Consequently refer to external PA instead of inverting the logic and
use an internal PA capability flag which is a bit confusing.
Currently this is used for Rt3352 only, but MT7620A also allows for an
external PA which will be supported by a follow up patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Basic support for MT7620 built-in wireless radio was added to
OpenWrt in r41441. It has seen some heavy cleaning and refactoring
since in order to match the Kernel's code quality standards.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of the macros used to describe the TX_PWR_CFG_4 register accidentally
refer to TX_PWR_CFG_3, probably a copy&paste error. Fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Even if we do not set AMPDU bit in TXWI, device still can aggregate
frame and send it with rate not corresponding to requested. That mean
we can do not sent probe frames with requested rate. To prevent that
use TXOP_BACKOFF for probe frames.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We use skb_desc->tx_rate_flags from entry as rate[].flags even if
skb does not match status. Patch corrects flags and also fixes
mcs for legacy rates.
rt2800_rate_from_status() is based on Felix's mt76
mt76x2_mac_process_tx_rate() function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we do not match skb entry, provide tx status via nomatch procedure.
Currently in that case we do rt2x00lib_txdone_noinfo(TXDONE_NOINFO),
which actually assume that entry->skb was posted without retries and
provide rate saved in skb desc as successful. Patch changed that to
rate read from TX_STAT_FIFO, however still do not provide correct
number of retries.
On SoC/PCI devices we keep providing status via standard txdone
procedure, no change in those devices, though we should thing about it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add bits rt2x00lib_fill_tx_status() when filling status in nomatch
case and hopefully do not break the function for existing cases.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This txdone nomatch function will be used when we get status from the HW,
but we could not match it with any sent skb.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This makes rt2x00lib_txdone a bit simpler and will allow to reuse
code in different variant of txdone which I'm preparing.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This makes rt2x00lib_txdone a bit simpler and will allow to reuse code
in different variant of txdone which I'm preparing.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add framework to identify sta based on tx status WCID. This is currently
not used, will start be utilized in the future patch.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The rt2800_drv_data structure contains driver specific
information. Move the declaration into the rt2800lib.h
header which is a more logical place for it. Also fix
the comment style to avoid checkpatch warning.
The patch contains no functional changes, it is in
preparation for the next patch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set the NL80211_EXT_FEATURE_CQM_RSSI_LIST wiphy extended feature
wholesale in all mac80211-based drivers that do not set the
IEEE80211_VIF_BEACON_FILTER flags on their interfaces. mac80211 will
be processing supplied RSSI values in ieee80211_rx_mgmt_beacon and
will detect when the thresholds set by
ieee80211_set_cqm_rssi_range_config are crossed. Remaining (few)
drivers need code to enable the firmware to monitor the thresholds.
This is mostly only compile-tested.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Declaring the factor is counter-intuitive, and people are prone
to using small(-ish) values even when that makes no sense.
Change the DECLARE_EWMA() macro to take the fractional precision,
in bits, rather than a factor, and update all users.
While at it, add some more documentation.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When CONFIG_KASAN is set, we get a rather large stack here:
drivers/net/wireless/ralink/rt2x00/rt2500usb.c: In function 'rt2500usb_set_device_state':
drivers/net/wireless/ralink/rt2x00/rt2500usb.c:1074:1: error: the frame size of 3032 bytes is larger than 100 bytes [-Werror=frame-larger-than=]
If we don't force those functions to be inline, the compiler can figure this
out better itself and not inline the functions when doing so would be harmful,
reducing the stack size to a merge 256 bytes.
Note that there is another problem that manifests in this driver, as a result
of the typecheck() macro causing even larger stack frames.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
queue_entry field of skbdesc is not read any more, remove it to allow
skbdesc contain other data.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We might kill TX or RX urb during rt2x00usb_flush_entry(), what can
cause anchor list corruption like shown below:
[ 2074.035633] WARNING: CPU: 2 PID: 14480 at lib/list_debug.c:33 __list_add+0xac/0xc0
[ 2074.035634] list_add corruption. prev->next should be next (ffff88020f362c28), but was dead000000000100. (prev=ffff8801d161bb70).
<snip>
[ 2074.035670] Call Trace:
[ 2074.035672] [<ffffffff813bde47>] dump_stack+0x63/0x8c
[ 2074.035674] [<ffffffff810a2231>] __warn+0xd1/0xf0
[ 2074.035676] [<ffffffff810a22af>] warn_slowpath_fmt+0x5f/0x80
[ 2074.035678] [<ffffffffa073855d>] ? rt2x00usb_register_write_lock+0x3d/0x60 [rt2800usb]
[ 2074.035679] [<ffffffff813dbe4c>] __list_add+0xac/0xc0
[ 2074.035681] [<ffffffff81591c6c>] usb_anchor_urb+0x4c/0xa0
[ 2074.035683] [<ffffffffa07322af>] rt2x00usb_kick_rx_entry+0xaf/0x100 [rt2x00usb]
[ 2074.035684] [<ffffffffa0732322>] rt2x00usb_clear_entry+0x22/0x30 [rt2x00usb]
To fix do not anchor TX and RX urb's, it is not needed as during
shutdown we kill those urbs in rt2x00usb_free_entries().
Cc: Vishal Thanki <vishalthanki@gmail.com>
Fixes: 8b4c000931 ("rt2x00usb: Use usb anchor to manage URB")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As reported by Felix:
Though protected by an ifdef, introducing an usb symbol dependency in
the rt2x00lib module is a major inconvenience for distributions that
package kernel modules split into individual packages.
Get rid of this unnecessary dependency by calling the usb related
function from a more suitable place.
Cc: Vishal Thanki <vishalthanki@gmail.com>
Reported-by: Felix Fietkau <nbd@nbd.name>
Fixes: 8b4c000931 ("rt2x00usb: Use usb anchor to manage URB")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we restart system using sysrq RT3290 device do not initalize
properly, hance always enable it via WLAN_FUN_CTRL register on
probe.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=85461
Reported-and-tested-by: Giedrius Statkevičius <edrius.statkevicius@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
clk_get() takes two arguments and might return ERR_PTR(), so we
have to nullify pointer on that case, to do not break further call
to clk_get_rate().
Reported-by: Felix Fietkau <nbd@nbd.name>
Fixes: 34db70b92f ("rt2x00: add copy of clk for soc devices")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support for the RT5350 WiSoC was added to OpenWrt after having a
lengthy debate about the legality of the original submission, see
https://lists.openwrt.org/pipermail/openwrt-devel/2013-January/018224.html
MTK/Ralink Acked replied and says we can merge this patch under the GPL.
https://dev.openwrt.org/changeset/36177
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Tested-by: Michel Stempin <michel.stempin@wanadoo.fr>
Acked-by: John Crispin <blogic@openwrt.org>
[daniel@makrotopia.org: added commit message, cleaned up code]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On Rt3352 the driver needs to know the frequency of an external
crystal which can be either 40 MHz (as on all other WiSoCs until now)
or 20 MHz.
Get the clock attached by ramips WiSoC platform code which probes
SYSC_REG_SYSCFG (added by John Crispin in commit 6ac8579b96) and
introduce a new flag clk_is_20mhz in struct hw_mode_spec to make the
driver aware and use either 40 MHz or 20 MHz specific rf_vals on those
WiSoC platforms.
The introduced support for boards with a 20 MHz crystal is also needed
for RT5350.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since clk_get() is not trivial add copy of clk pointer to rt2x00dev
for System On Chip devices and initialize it on probe routine.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is needed for WiFi to work e.g. on DIR-615 rev.H1 which got
external RF power amplifiers connected to the WiSoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simple patch to correct HT20/HT40 filter setting.
Tested with Rt3290, Rt3352 and Rt5350
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since rt2800pci update beacon settings asynchronously from
tbtt tasklet, without beacon_skb_mutex protection, number of
currently active beacons entries can be different than
number pointed by rt2x00dev->intf_beaconing. Remove warning
about that inconsistency.
Reported-by: evaxige@qq.com
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All Ralink USB devices I have, including old ones, work well with
max_psdu = 3 (64kB tx AMPDUs).
Fix indent on the way.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we do not get TX status in reasonable time, we most likely fail to
send frame hence mark it as so.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable RTS frame retry fall-back and limit number of RTS retries to 7
what is default number of retries for small frames. As RTS/CTS is used
for TXOP protection, those settings prevent posting lots of RTS
frames when remote station do not response with CTS at the moment. After
sending 7 RTS's the HW will start back-off mechanism and after it will
start posing RTS again to get access to the medium.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We do not have option to set per frame retry count. We have only global
TX_RTY_CFG registers which specify the number or retries. Set setting
of that register to value that correspond rate control algorithm number
of frame post (number of retries + 1), which is 3 for aggregated frames.
This should help with big amount of retries on bad conditions, hence
mitigate buffer-bloat like problems.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reset tuner use curr_band value, make sure it is updated.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When medium is busy or frames have to be resend, it takes time to send
the frames and get TX status from hardware. For some really bad medium
conditions it can take seconds. Patch change TX status timeout to give
HW more time to provide it, however 500ms is not enough for bad
conditions. In the future this timeout should be removed and replaced
with proper watchdog mechanism.
Increase flush timeout accordingly as well.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On rt2800usb, if we do not get TX status from HW, we assume frames were
posted and after entry->last_action timeout, we forcibly provide TX
status to mac80211. So it's not possible to detect hardware TX hung
based on the timeout. Additionally TXRQ_PCNT tells on number of frames
in the Packet Buffer (buffer between bus interface and chip MAC
subsystem), which can be non zero on normal conditions. To check HW hung
we will need provide some different mechanism, for now remove watchdog
as current implementation is wrong and not useful.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The most notable change here is the inclusion of airtime fairness
scheduling to ath9k. It prevents slow clients from hogging all the
airtime and unfairly slowing down faster clients.
Otherwise smaller changes and cleanup.
Major changes:
ath9k
* cleanup eeprom endian handling
* add airtime fairness scheduling
ath10k
* fix issues for new QCA9377 firmware version
* support dev_coredump() for firmware crash dump
* enable channel 169 on 5 GHz band
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYalDTAAoJEG4XJFUm622ba2EH/ivoHG9CvmT6HgNw77odDr6b
Zc7plDi2dd9LIzp3rF/9j8Ietfzpu31Pp9Qz0o1Su/s8RJIlXKVF5UeG5IignnEG
02rv7Z+BGPW7SUNDb0cLa27PMYqUAh8vI39sxYSdQ9NQLIlpMLIxxx5iOZyAK5eV
HBRS0pVlSxbAntb1JgWiN/LjjXe/PdhX3CR/b9b468KAcWB6UWj9nXQxFmz7d3uM
dH3buDTgwaq7K24ZAFc1BsD7rgxprpauXxgIMWCKxRERf64WFfYkYdfdCER+PSPH
maV5Te1KzTJBrQHDOPs1ezVe8gDUhb5YE4BJY9SppZpOE1arucq2g3+3obQUeHE=
=DAVq
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-01-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
The most notable change here is the inclusion of airtime fairness
scheduling to ath9k. It prevents slow clients from hogging all the
airtime and unfairly slowing down faster clients.
Otherwise smaller changes and cleanup.
Major changes:
ath9k
* cleanup eeprom endian handling
* add airtime fairness scheduling
ath10k
* fix issues for new QCA9377 firmware version
* support dev_coredump() for firmware crash dump
* enable channel 169 on 5 GHz band
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not perform mac80211 config and link_tuner at the same time,
this can possibly result in wrong RF or BBP configuration.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
msleep(1) can sleep much more time then requested 1ms, this is not good
on channel switch, which we want to be performed fast (i.e. to make scan
faster). Replace msleep() with usleep_range(), which has much smaller
maximum sleeping time boundary.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This procedure can sleep, hence mdelay is not needed.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We need to perform different actions (AGC and VCO calibrations and VGC
tuning) periodically at different intervals. We don't need separate
works for those, we can use link tuner work and just check for proper
interval on it.
This fixes performing AGC and VCO calibration when scanning on STA
mode. We need to be on-channel to perform those calibrations.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since we reset TX_PIN_CFG register, we have to finish recalibration.
Warn if this is not possible.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have different modes of adjusting freq offset on different chips.
Call current adjustment similarly like vendor driver - mode1 .
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MAX_LEN_CFG_MAX_PSDU specify maximum transmitted by HW AMPDU length
(0 - 8kB, 1 - 16kB, 2 - 32kB, 3 - 64kB). Set this option according to
remote stations capabilities (based on HT ampdu_factor). However limit
the value based our hardware TX capabilities as some chips can not send
more than 16kB (factor 1). Limit for all chips is currently 32kB
(factor 2), but perhaps for some chips this could be increased
to 64kB by setting drv_data->max_psdu to 3.
Since MAX_LEN_CFG_MAX_PSDU is global setting, on multi stations modes
(AP, IBSS, mesh) we limit according to less capable remote STA. We can
not set bigger value to speed up communication with some stations and
do not break communication with slow stations.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not set ampdu_density and ba_size for frames without AMPDU bit i.e.
frames that will not be aggregated to AMPDU.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initalize max ampdu_factor supported by us based on rx chains, vendor
driver do the same.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYOAC4AAoJEG4XJFUm622bUYkH/3SSYp6moSdKpVnVPx7ST7yK
t9WHR9IMZFIhD6vq8AK6+8OQr1TgGjHfPu+WZj7CIl8nu53kcgPRi51gg1mndbNg
9N3RbVp06nGbM2VnW8ZIpg3OLIXatZ4c9g3LFvvtyobYvWGJ6W4D79JdlmTG1ELr
XAjInbxFsgon+CwqCMOaAJx8xYp42rBnPRZZvhOq9O33kRw8Umo9UQw0s1U2Vfgx
prxQ6d0GxNAPEe8QiDw/vtBcXWFMOhQeDl8sK70ZcojSn1FY730NsIh/Y86PcQTK
6TsvOL5gg+rd0ln8TZRAslnDrZBAhTEDqUzLQMRJ9VjEj5RFd8eLCSIzHfaroI8=
=4qCH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending frames in CCK rates on HT can cause performance problems.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use RTS/CTS protection for TXOP on all rates modes as default and
disable CCK rates (this cause performance problems).
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change default to RTS/CTS protection. This has a cost of transmitting
one more control frame (RTS) however protect us from traffic from
hidden node.
On station mode will use CTS-to-self if AP will configure that
for the network.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Those TX_SW_CFG1 values are used in vendor driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialize AUTO_RSP_CFG register to similar value as vendor driver does.
Do not set BAC_ACK_POLICY based on short preamble setting, those are
unrelated.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We already initlized WPDMA_GLO_CFG_WP_DMA_BURST_SIZE to 3 on
rt2800_init_registers() for USB devices. For PCI devices we will use
HW default setting, which is 2, so patch does not change behaviour
on PCI devices.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We should not reset USB_DMA_CFG on rt2800usb_init_registers() as this
function is called indirectly from rt2800_enable_radio(). If we
do so, we wipe out USB_DMA_CFG settings from rt2800usb_enable_radio().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We should only set IEEE80211_HT_MCS_TX_RX_DIF when TX and RX MCS sets
are not equal, i.e. when number of tx streams is different than
number of RX streams.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In device removal routine, usage of "#ifdef CONFIG_RT2X00_LIB_USB"
will not cover the case when it is configured as module. This will
omit the entire if-block which does cleanup of URBs and cancellation
of pending work. Changing the #ifdef to #if IS_ENABLED() to fix it.
Signed-off-by: Vishal Thanki <vishalthanki@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On some devices the EEPROMs of Ralink Wi-Fi chips have a default Ralink
MAC address set (RT3062F: 00:0C:43:30:62:00, RT3060F:
00:0C:43:30:60:00). Using multiple of these devices in the same network
can cause nasty issues.
Allow to override the MAC in the EEPROM with (a known good) one set in
the device tree to bypass the issue.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The old WDS 4-addr frame support is very limited, e.g.
* no encryption is possible on such links
* it cannot support rate/HT/VHT negotiation
* management APIs are very restricted
These make the WDS legacy mode useless in practice.
All of these are resolved by the 4-addr AP/client support,
so there's also no reason to improve WDS in the future.
Therefore, add a Kconfig option to disable legacy WDS.
This gives people an "emergency valve" while they migrate
to the better-supported 4-addr AP/client option; we plan
to remove it (and the associated cfg80211/mac80211 code,
which is the ultimate goal) in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We know that 'retval = 0' because it has been tested a few lines above.
So, if 'devm_kmalloc' fails, 0 will be returned instead of an error code.
Return -ENOMEM instead.
Fixes: 8b4c000931 ("rt2x00usb: Use usb anchor to manage URB")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If rt2800usb is loaded with nohwcrypt=1, mac80211 takes
care of the crypto with software encryption/decryption
and thus, MFP can be used.
Tested for secured mesh using ath9k_htc and ath9k.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With current driver, it is observed that a URB is not
completed while the USB disconnect is initiated. Due to
that, the URB completion handler is trying to access
the resource which was freed as a part of USB disconnect.
Managing the URBs with anchor will make sure that all
the URBs are handled gracefully before device gets
disconnected.
Signed-off-by: Vishal Thanki <vishalthanki@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add USB ID 0411:01fd for Buffalo WLI-UC-G450 wireless adapter,
RT chipset 3593
Signed-off-by: Anthony Wong <anthony.wong@ubuntu.com>
Cc: stable@vger.kernel.org
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The buffer needs to be zero terminated in case the user data is not.
Otherwise we run off the end of the buffer.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wl12xx
* add device tree support for SPI
mwifiex
* add debugfs file to read chip information
* add MSIx support for newer pcie chipsets (8997 onwards)
* add schedule scan support
* add WoWLAN net-detect support
* firmware dump support for w8997 chipset
iwlwifi
* continue the work on multiple Rx queues
* add support for beacon storing used in low power states
* use the regular firmware image of WoWLAN
* fix 8000 devices for Big Endian machines
* more firmware debug hooks
* add support for P2P Client snoozing
* make the beacon filtering for AP mode configurable
* fix transmit queues overflow with LSO
libertas
* add support for setting power save via cfg80211
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWvbW+AAoJEG4XJFUm622b1lIH/RmFoJNbJka9/CrDse5ndb3A
TBRDGvinOjubHn9Hn8Baz7u0huXvBpWoN/YI4hqjKTW4YsXfN8cB1IJakzohLFCF
I9kUhITYGrK7hKDwkBsop2qxwJsrkAzv/XNzi+yGqxlj/IqZp+pYBmZTb9H6G963
lb8hJPhx+t2aCBPvDdkAd5n67kdq0C35At+a1KB1CYFYKdYO5y5QeDLYtb+5zrWT
/Pwel7gRdgcf4TpaUZs++mDf+agcFo+JjG+olLrZNw1BDthA8VC46agMyfffrt4l
dRZIS07fUDd0zf4HJMWV05l8kKdEwqrRAuoBOnxGI611GNN94M3NWJDxU/MgBos=
=zE9m
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-02-12' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
wl12xx
* add device tree support for SPI
mwifiex
* add debugfs file to read chip information
* add MSIx support for newer pcie chipsets (8997 onwards)
* add schedule scan support
* add WoWLAN net-detect support
* firmware dump support for w8997 chipset
iwlwifi
* continue the work on multiple Rx queues
* add support for beacon storing used in low power states
* use the regular firmware image of WoWLAN
* fix 8000 devices for Big Endian machines
* more firmware debug hooks
* add support for P2P Client snoozing
* make the beacon filtering for AP mode configurable
* fix transmit queues overflow with LSO
libertas
* add support for setting power save via cfg80211
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Space needed before open parenthesis
Signed-off-by: Paul McQuade <paulmcquad@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Removed empty spaces before/after parenthesis
Signed-off-by: Paul McQuade <paulmcquad@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Removed empty spaces before/after parenthesis
Signed-off-by: Paul McQuade <paulmcquad@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit df1404650c ("mac80211: remove support for IFF_PROMISC")
monitor mode for rt2x00 has been made effectively useless because the
hardware filter is configured to drop packets whose intended recipient is
not the device, regardless of the presence of monitor mode interfaces.
This patch fixes this regression by adding explicit monitor mode support,
and by configuring the hardware filter accordingly.
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently mac80211 does not inform the driver of the session
block ack timeout when starting a rx aggregation session.
Drivers that manage the reorder buffer need to know this
parameter.
Seeing that there are now too many arguments for the
drv_ampdu_action() function, wrap them inside a structure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver calls pci_set_mwi to enable memory-write-invalidate when it
is initialized, but does not call pci_clear_mwi when it is removed. Many
other drivers calls pci_clear_mwi when pci_set_mwi is called, such as
r8169, 8139cp and e1000.
This patch adds pci_clear_mwi in error handling and removal procedure,
which can fix the problem.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This code causes a static checker bug.
drivers/net/wireless/ralink/rt2x00/rt2500usb.c:232 _rt2500usb_register_read()
warn: passing casted pointer 'value' to 'rt2500usb_register_read()' 32 vs 16.
If the low 16 bits were initialized to zero then this code would only be
a problem on big endian systems. But in this case this is case the low
16 bits are never initialized. This is called from a function which is
created using a macro:
RT2X00DEBUGFS_OPS(csr, "0x%.8x\n", u32);
We end up copying uninitialized data to the user which is bogus and an
information leak.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
