Simultaneous audio playback and capture on OMAP1510 can cause that second
stream is stalled if there is enough delay between startup of the audio
streams.
Current implementation of the omap_mcbsp_start is starting both transmitter
and receiver at the same time and it is called only for firstly started
audio stream from the OMAP McBSP based ASoC DAI driver.
Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is
missed if there is no DMA transfer set up at that time when the first word
after McBSP startup is transmitted. The problem hasn't noted before since
later OMAPs are using level sensitive DMA request lines.
Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by
allowing to start and stop individually McBSP transmitter and receiver
logics. Then call those functions individually for both audio playback
and capture streams. This ensures that DMA transfer is setup before
transmitter or receiver is started.
Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem
analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA
request line behavior differences between the OMAP generations.
Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
<linux/clk.h> should be included to get the base API prototypes.
This fixes the following sparse warnings:
arch/arm/common/clkdev.c:65:12:
warning: symbol 'clk_get_sys' was not declared. Should it be static?
arch/arm/common/clkdev.c:79:12:
warning: symbol 'clk_get' was not declared. Should it be static?
arch/arm/common/clkdev.c:87:6:
warning: symbol 'clk_put' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
preserve_crunch_context() calls __copy_to_user() which expects the
destination address to be in __user space. setup_sigframe() properly
passes the destination address.
restore_crunch_context() calls __copy_from_user() which expects the
source address to be in __user space. restore_sigframe() properly
passes the source address.
This fixes {preserve/restore}_crunch_context() to accept the
address as __user space and resolves the following sparse warnings:
arch/arm/kernel/signal.c:146:31:
warning: incorrect type in argument 1 (different address spaces)
expected void [noderef] <asn:1>*to
got struct crunch_sigframe *frame
arch/arm/kernel/signal.c:156:38:
warning: incorrect type in argument 2 (different address spaces)
expected void const [noderef] <asn:1>*from
got struct crunch_sigframe *frame
arch/arm/kernel/signal.c:250:48:
warning: incorrect type in argument 1 (different address spaces)
expected struct crunch_sigframe *frame
got struct crunch_sigframe [noderef] <asn:1>*<noident>
arch/arm/kernel/signal.c:365:49:
warning: incorrect type in argument 1 (different address spaces)
expected struct crunch_sigframe *frame
got struct crunch_sigframe [noderef] <asn:1>*<noident>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Stop referencing CLOCK_TICK_RATE in the KS8695 drivers, rather refer
to a KS8695_CLOCK_RATE.
Issue pointed out by Russell King on arm-linux-kernel mailing list.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This sockopt goes in line with SO_TYPE and SO_PROTOCOL. It makes it
possible for userspace programs to pass around file descriptors — I
am referring to arguments-to-functions, but it may even work for the
fd passing over UNIX sockets — without needing to also pass the
auxiliary information (PF_INET6/IPPROTO_TCP).
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to SO_TYPE returning the socket type, SO_PROTOCOL allows to
retrieve the protocol used with a given socket.
I am not quite sure why we have that-many copies of socket.h, and why
the values are not the same on all arches either, but for where hex
numbers dominate, I use 0x1029 for SO_PROTOCOL as that seems to be
the next free unused number across a bunch of operating systems, or
so Google results make me want to believe. SO_PROTOCOL for others
just uses the next free Linux number, 38.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If IRQ triggering is enabled, it can trigger a pending interrupt
even for masked interrupts. Any pending GPIO interrupts can
prevent the powerdomain from hitting retention.
Problem found, reported and additional review and testing by Chunquiu
Wang.
Tested-by: Chunquiu Wang <cqwang@motorola.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Powerdomain previous state is checked after restoring new states in
suspend. This patch fixes this problem.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Use the min/max settings from CPUfreq policy rather than
processor defined min/max settings.
Without this patch, it's possible to scale frequency outside
the current policy range.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Use list_add_tail() when adding discovered UART ports. This is so
traversal using list_for_each_entry() will traverse the list in the
order they were found.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch causes the OMAP uarts to honor the sysfs power/wakeup file
for IOPAD wakeups. Before the OMAP was always woken up from off mode
on a rs232 signal change. This patch also creates a different
platform device for each serial port so that the wakeup properties can
be control per port.
By default, IOPAD wakeups are enabled for each UART. To disable,
# echo disabled > /sys/devices/platform/serial8250.0/power/wakeup
Where serial8250.0 can be replaced by .1, or .2 to control the other
ports.
Original idea and original patch from Russ Dill <russ.dill@gmail.com>
Cc: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
It was possible for an unhandled interrupt to occur if there was incoming
serial traffic during wakeup from suspend. This was caused by the code
in arch-arm/mach-omap2/serial.c keeping interrupt enabled all the time,
but not acking its interrupts. Applies on top of PM branch.
Use the PM begin/end hooks to ensure that the "serial idle" interrupts
are disabled during the suspend path. Also, since begin/end hooks are
now used, use the suspend_state that is passed in the begin hook instead
of the enter hook as per the platform_suspend_ops docs.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Streamline the OMAP4 special IRQ assignments by putting inside
normal init loop instead of having a separate loop.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
By default, prevent functional wakeups from inside a module from
waking up the IVA2. Let DSP Bridge code handle this when loaded.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
gpio_get() should return DATAIN register value when the GPIO
is configured as input whereas it should return DATAOUT register
value when the GPIO is configured as output.
Now /sys/kernel/debug/gpio shows proper values for output GPIOs
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation
(x + d/2)/d but is perhaps more readable.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
@depends on haskernel@
expression x,__divisor;
@@
- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds board-specific data for IDE support on afeb9260.
Depends on #5631/1
Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds platform data for CF/IDE support
and SMC init code for AT91SAM9260 SoC.
Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add static setting cpu frequence for w90p910 platform.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SPI pins are now allocated in pcm037.c, remove them from EET.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: at_hdmac: add DMA slave transfers
dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller
dmaengine: dmatest: correct thread_count while using multiple thread per channel
dmaengine: dmatest: add a maximum number of test iterations
drivers/dma: Remove unnecessary semicolons
drivers/dma/fsldma.c: Remove unnecessary semicolons
dmaengine: move HIGHMEM64G restriction to ASYNC_TX_DMA
fsldma: do not clear bandwidth control bits on the 83xx controller
fsldma: enable external start for the 83xx controller
fsldma: use PCI Read Multiple command
The s3c64xx devices use the same hardware core as s3c24xx, so move
the timer/pwm handling to plat-s3c so it can be used by both.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the s3c_device_nand platform device from plat-s3c24xx to plat-s3c,
now that the nand driver also support the s3c64xx devices.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for the Airgoo HMT (home media terminal) device.
The HMT is a tablet device with a s3c6410, a 7" LCD and a number
of peripheral connections.
For more details of the hardware specs, see:
http://article.gmane.org/gmane.linux.debian.devel.embedded/4307
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
[ben-linux@fluff.org: subject rewrite]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The pwm hardware only checks the compare register after a decrement,
so the pin never toggles if tcmp = tcnt.
This happens when a very low duty cycle is requested. Fix it by always
ensuring that tcmp < tcnt.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add debugfs support for the cpufreq driver to allow
information about the system state to be exported to
the user.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add armclk for use with the cpufreq support and anything
else that may want it. This clock is just a direct
descendant of fclk.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add board support for CPUFREQ with the Simtec BAST board
registering the necessary information with the core.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add a sysdev S3C2410A sysdev to allow the differentiation
of the S3C2410A from the S3C2410. This is needed for the
CPUFREQ code to enable the extra features and update cpu
specific information.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update the mapping of the memory controler registers and
add the missing definitions of the register block for the
SSMC.
The register contents definitions can be found in the pl093
header.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Currently map-base.h defines the main virtual address mappings made
for all the support S3C SoC series, but does not then define any base
for per-cpu mappings to be made from.
Add S3C_ADDR_CPU() macro to define an virtual address as an offset
from the last of the core mappings.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add entries to select the crystal to select for each different
supported board. This information is then available for anything
else requiring this, such as the CPUFreq PLL tables.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add io-timing support for frequency scaling on the S3C2410 SoC.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the S3C24XX to the main ARM CPUFreq Kconfig support list.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add ARCH_HAS_CPUFREQ so that each machine config can select
it if they have CPUFREQ driver support. This means that the
CPUFREQ specific area does not need the if statement updating
each time a new machine is added.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the structure s3c_cpufreq_config from cpu-freq.h to the
less advertised cpu-freq-core.h as it is not needed by anything
outside the core drivers.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update arch/arm/plat-s3c/include/plat/cpu-freq.h to include kerneldoc
style documentation.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the core of the support for enabling the CPUFreq driver on
all S3C24XX based systems.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add definitions and an accessor macro to deal with
reading bus information from S3C2410_BWSCON for any
given numbered bank.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
CPUAT91 is based on Atmel's AT91RM9200 with up to 16MB Strataflash,
up to 128MB SDRAM and an ethernet PHY in RMII mode.
Signed-off-by: Eric Benard <ebenard@eukrea.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CPU9260 and CPU9G20 share the same PCB populated with either
Atmel's AT91SAM9260B or AT91SAM9G20B with up to 64MB Strataflash,
up to 128MB SDRAM, up to 2GB NAND and an ethernet PHY in RMII mode.
Signed-off-by: Eric Benard <eric@eukrea.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The EP93xx features two PWMs (one on the EP9307) with the following
features:
* Configurable dual output
* Separate input clocks for each PWM output
* 16-bit resolution
* Programmable pulse width (duty cycle), interval (frequency), and
polarity
This adds the necessary core support as well as the driver. A sysfs
interface is provided to control the PWM outputs.
Signed-off-by: Matthieu Crapet <mcrapet@gmail.com>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make software reset to avoid freeze if PCI bus was messed up
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After ftrace_trace_function is called r1 is probably clobbered so don't
try to use its value for restoring.
This was introduced in v2.6.29~38^2~7
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The value of armclk_mask needs to be inverted for use as a mask on
the register value when updating ARM_RATIO.
This is critical for cpufreq support, without it attempts to scale
the frequency of the core trash pretty much the entire clock tree.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
If the requested clock is faster than the parent clock then the
parent clock is the closest we can get to the request so we need
to return that instead of the requested clock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In the s3c_gpiolib_getchip implementation for s3c24xx the check whether a pin is
in the gpio banks range is reversed. Thus the function returns NULL for valid
pins and the gpio chip if its not valid.
As a result gpio states are not saved/restored properly during suspend/resume.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch creates McBSP support on OMAP4430 development platform. This patch
includes corresponding base address changes for OMAP4.
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
- enable PCM043, MX31LILLY, ARMADILLO5X0 and MX35_3DS boards
- enable MXC nand driver
- enable UBI support
- disable cs89x0 support which broke all boards which do not have this chip
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
mm: Pass virtual address to [__]p{te,ud,md}_free_tlb()
Upcoming paches to support the new 64-bit "BookE" powerpc architecture
will need to have the virtual address corresponding to PTE page when
freeing it, due to the way the HW table walker works.
Basically, the TLB can be loaded with "large" pages that cover the whole
virtual space (well, sort-of, half of it actually) represented by a PTE
page, and which contain an "indirect" bit indicating that this TLB entry
RPN points to an array of PTEs from which the TLB can then create direct
entries. Thus, in order to invalidate those when PTE pages are deleted,
we need the virtual address to pass to tlbilx or tlbivax instructions.
The old trick of sticking it somewhere in the PTE page struct page sucks
too much, the address is almost readily available in all call sites and
almost everybody implemets these as macros, so we may as well add the
argument everywhere. I added it to the pmd and pud variants for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV]
Acked-by: Nick Piggin <npiggin@suse.de>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
correct GPIO freed in treo680_irda_shutdown()
Signed-off-by: Tomáš ?ech <sleep_walker@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It adds DMA peripheral identifiers for hardware handshaking interface. It will
be used in platform code.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/plat-stmp3xxx/pinmux.c: linux/sysdev.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: dmitry pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/plat-s3c64xx/pm.c: plat/regs-gpio.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-omap2/mcbsp.c: mach/irqs.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-omap1/mcbsp.c: mach/irqs.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-sffsdr.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm646x-evm.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm644x-evm.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm355-leopard.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm355-evm.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/include/asm/atomic.h: asm/system.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/boot/compressed/misc.c: linux/compiler.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix two bugs in the OMAP3 clock tree pertaining to the SSI, DSS,
USBHOST, and HSOTGUSB devices. These devices are both interconnect
initiators and targets. Without this patch, clk_enable()s on clocks for
these modules can be very high latency (potentially up to ~200
milliseconds) and message such as the following are generated:
Clock usbhost_48m_fck didn't enable in 100000 tries
Two bugs are fixed by this patch. First, OMAP hardware only supports
target CM_IDLEST register bits on ES2+ chips and beyond. ES1 chips
should not wait for these clocks to enable. So, split the appropriate
clocks into ES1 and ES2+ variants, so that kernels running on ES1
devices won't try to wait.
Second, the current heuristic in omap2_clk_dflt_find_idlest() will
fail for these clocks. It assumes that the CM_IDLEST bit to wait upon
is the same as the CM_*CLKEN bit, which is false[1]. Fix by
implementing custom clkops .find_idlest function pointers for the
appropriate clocks that return the correct slave IDLEST bit shift.
This was originally fixed in the linux-omap kernel during 2.6.29 in a
slightly different manner[2][3].
In the medium-term future, all of the module IDLEST code will
eventually be moved to the omap_hwmod code.
Problem reported by Jarkko Nikula <jhnikula@gmail.com>:
http://marc.info/?l=linux-omap&m=124306184903679&w=2
...
1. See for example 34xx TRM Revision P Table 4-213 and 4-217 (for the
DSS case).
2. http://www.spinics.net/lists/linux-omap/msg05512.html et seq.
3. http://lkml.indiana.edu/hypermail/linux/kernel/0901.3/01498.html
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the CM_*CLKEN bits
are in CM_{I,F}CLKEN2_CORE [1]. Fix by implementing a custom clkops
.find_idlest function to return the correct slave IDLEST register.
...
1. OMAP2430 Multimedia Device Package-on-Package (POP) Silicon Revision 2.1
(Rev. V) Technical Reference Manual, tables 4-99 and 4-105.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some OMAP2/3 hardware modules have CM_IDLEST attributes that are not
handled by the current omap2_wait_clock_ready() code. In preparation
for patches that fix the unusual devices, rename the function
omap2_wait_clock_ready() to omap2_wait_module_ready() and split it
into three parts:
1. A clkops-specific companion clock return function (by default,
omap2_clk_dflt_find_companion())
2. A clkops-specific CM_IDLEST register address and bit shift return
function (by default, omap2_clk_dflt_find_idlest())
3. Code to wait for the CM to indicate that the module is ready
(omap2_cm_wait_idlest())
Clocks can now specify their own custom find_companion() and find_idlest()
functions; used in subsequent patches.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The clock stabilization delay post a M2 divider change is needed
even before a SDRC interface clock re-enable and not only before
jumping back to SDRAM.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch fixes a bug in the CORE dpll scaling sequence which was
errouneously clearing some bits in the SDRC DLLA CTRL register and
hence causing a freeze. The issue was observed only on platforms
which scale CORE dpll to < 83Mhz and hence program the DLL in fixed
delay mode.
Issue reported by Limei Wang <E12499@motorola.com>, with debugging
assistance from Richard Woodruff <r-woodruff2@ti.com> and Girish
Ghongdemath <girishsg@ti.com>.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Limei Wang <E12499@motorola.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Girish Ghongdemath <girishsg@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: updated patch description to include collaboration credits]
Stop setting SDRC_POWER.PWDENA on boot. There is a nasty erratum
(34xx erratum 1.150) that can cause memory corruption if PWDENA is
enabled.
Based originally on a patch from Samu P. Onkalo <samu.p.onkalo@nokia.com>.
Tested on BeagleBoard rev C2.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Samu P. Onkalo <samu.p.onkalo@nokia.com>
This patches ensures the MUX settings are correct for the SDRC
CKE signals to SDRAM. This allows the self-refresh to work when
2 chip-selects are in use.
A warning is thrown away in case the initial muxing is incorrect,
in order to track faulty or old-dated bootloaders.
Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options
must be enabled for the mux code to have effect.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.
This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS
Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers
Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The patch removes the "mrc" instruction in head-nommu.S overriding the
r0 register containing the value to be written in the CP15 system
control register.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The patch below adds ARM ptrace functions to get the process load address.
This is required for useful userspace debugging on mmuless systems. These
values are obtained by reading magic offsets with PTRACE_PEEKUSR, as on other
nommu targets. I picked arbitrary large values for the offsets.
Signed-off-by: Paul Brook <paul@codesourcery.com>
The patch adds the necessary ifdefs around functions that only make
sense when the MMU is enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the necessary entries to the Makefile and Kconfig
files for building the Thumb-2 kernel.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch sets bit 0 in the startup address passed to the secondary
CPUs so that they branch into Thumb-2 mode.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Modules compiled to Thumb-2 have two additional relocations needing to
be resolved at load time, R_ARM_THM_CALL and R_ARM_THM_JUMP24, for BL
and B.W instructions. The maximum Thumb-2 addressing range is +/-2^24
(+/-16MB) therefore the MODULES_VADDR macro in asm/memory.h is set to
(MODULES_END - 8MB) for the Thumb-2 compiled kernel.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds various C and assembler macros that help with using
the unified assembler syntax for compiling files to either ARM or
Thumb-2 modes.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since the Thumb-2 instructions can be 16-bit wide, data in the .text
sections may not be aligned to a 32-bit word and this leads to unaligned
exceptions. This patch does not affect the ARM code generation.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch updates the platform dma.h with new dma request lines
for OMAP4 peripherals. Also additional hardware register of OMAP4
sDMA module are included.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add spi resource define for w90p910 spi driver.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When programming clock api, I named this spi device
as w90p910-usi, now, I think named it as w90p910-spi better
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add mac resource define for w90p910 mac driver.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add fmi resource define for w90p910 platform.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the NOR flash support for TS-7200.
The TS-7200 models all have 16-bit NOR flash. Update the platform
init to support this.
Remove the private TS72XX_NOR_* defines and use the common ep93xx
defines for the external chip select physical base address instead.
Move the NOR flash registration into a static __init function. When
the NAND flash support is updated this function will also be used
to register the NAND flash for the TS-7250 and TS-7260.
Tested-by: Matthieu Crapet <mcrapet@gmail.com>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch for at_hdmac adds the slave transfers capability to the Atmel DMA
controller available on some AT91 SOCs. This allow peripheral to memory and
memory to peripheral transfers with hardware handshaking.
Slave structure for controller specific information is passed through channel
private data. This at_dma_slave structure is defined in at_hdmac.h header file
and relative hardware definition are moved to this file from at_hdmac_regs.h.
Doing this we allow the channel configuration from platform definition code.
This work is intensively based on dw_dmac and several slave implementations.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on
at91sam9rl chip. It will be used on other products in the future.
This first release covers only the memory-to-memory tranfer type. This is the
only tranfer type supported by this chip. On other products, it will be used
also for peripheral DMA transfer (slave API support to come).
I used dmatest client without problem in different configurations to test it.
Full documentation for this controller can be found in the SAM9RL datasheet:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4243
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
clk_disable() in remove method is not needed since we already
have clk_disable in pxa27x_keypad_close().
Also make sure the driver uses resource_size() and helpers from
include/input/matrix_keypad.h
Tested-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If CONFIG_APM_EMULATION=n em-x270 build fails with linker error:
arch/arm/mach-pxa/built-in.o: In function `em_x270_battery_critical': em-x270.c:(.text+0x12c0): undefined reference to `apm_queue_event'
arch/arm/mach-pxa/built-in.o: In function `em_x270_battery_low': em-x270.c:(.text+0x12c8): undefined reference to `apm_queue_event'
make: *** [.tmp_vmlinux1] Error 1
Fix it.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch reworks platform driver power management code
for omap drivers using late/early legacy callbacks.
The callbacks are converted for CONFIG_SUSPEND like this:
suspend_late() -> suspend_noirq()
resume_early() -> resume_noirq()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Allow architecture specific data in struct platform_device V3.
With this patch struct pdev_archdata is added to struct
platform_device, similar to struct dev_archdata in found in
struct device. Useful for architecture code that needs to
keep extra data associated with each platform device.
Struct pdev_archdata is different from dev.platform_data, the
convention is that dev.platform_data points to driver-specific
data. It may or may not be required by the driver. The format
of this depends on driver but is the same across architectures.
The structure pdev_archdata is a place for architecture specific
data. This data is handled by architecture specific code (for
example runtime PM), and since it is architecture specific it
should _never_ be touched by device driver code. Exactly like
struct dev_archdata but for platform devices.
[rjw: This change is for power management mostly and that's why it
goes through the suspend tree.]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
From: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
As __builtin_return_address(n) doesn't work for ARM with n > 0, the
kernel needs its own implementation.
This fixes many warnings saying:
warning: unsupported argument to '__builtin_return_address'
The new methods and walk_stackframe must not be instrumented because
CALLER_ADDRESSx is used in the various tracers and tracing the tracer is
a bad idea.
What's currently missing is an implementation using unwind tables. This
is not fatal though, it's just that the tracers don't get enough
information to be really useful.
Note that if both ARM_UNWIND and FRAME_POINTER are enabled,
walk_stackframe uses unwind information. So in this case the same
implementation is used as when FRAME_POINTER is disabled.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The EP93xx has two gpio pins specifically assigned to drive
external LEDs. Add core support for these LEDs.
On the EDB93xx development boards, the rdled is connected to
an external reset circuit. Turning this led on for an extended
amount of time will cause the circuit to issue a manual reset.
Refer to Cirrus App Note AN258 for more information.
http://www.cirrus.com/en/pubs/appNote/AN258REV2.pdf
This led can be safely used as the system heartbeat with the
ledtrig-heartbeat driver.
echo heartbeat > /sys/class/leds/platform:rdled/trigger
The grled can be used for any desired purpose.
Tested-by: Matthieu Crapet <mcrapet@gmail.com>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix i2c_board_info definitions - we were defining the 'type' field
of these structures twice since the first argument of I2C_BOARD_INFO
sets this field. Move the second definition into I2C_BOARD_INFO().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Add support for the ADC controller on the S3C series of processors to
drivers/hwmon for use with hardware monitoring systems.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
To add HWMON support, we need a synchronous read() call that blocks
until completion. Add the client that is being service to the select
and convert callbacks to make the code easier.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add platform device information for the ADC channels to be exported
via HWMON. This exports all the ADCs not being used for the touchscreen
interface.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change the hwmon device name to something more generic as this
should be functional for both the s3c24xx and s3c64xx archs.
Since it has yet to have a driver, it is pretty safe to change
as there are no extant users.
Also add the necessary entry in devs.h which seems to have been
missed out at somepoint.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
WARNING: at drivers/gpio/gpiolib.c:83 gpio_ensure_requested+0x58/0xbc()
autorequest GPIO-71
Modules linked in:
[<c0028bd0>] (unwind_backtrace+0x0/0xe8) from [<c003c328>] (warn_slowpath_common+0x48/0x78)
[<c003c328>] (warn_slowpath_common+0x48/0x78) from [<c003c394>] (warn_slowpath_fmt+0x28/0x38)
[<c003c394>] (warn_slowpath_fmt+0x28/0x38) from [<c0146128>] (gpio_ensure_requested+0x58/0xbc)
[<c0146128>] (gpio_ensure_requested+0x58/0xbc) from [<c0146308>] (gpio_direction_input+0x80/0xf4)
[<c0146308>] (gpio_direction_input+0x80/0xf4) from [<c000c668>] (zylonite_pxa300_init+0x108/0x214)
[<c000c668>] (zylonite_pxa300_init+0x108/0x214) from [<c000c4e4>] (zylonite_init+0x8/0x84)
[<c000c4e4>] (zylonite_init+0x8/0x84) from [<c00097cc>] (customize_machine+0x18/0x24)
[<c00097cc>] (customize_machine+0x18/0x24) from [<c00222e0>] (do_one_initcall+0x30/0x1b0)
[<c00222e0>] (do_one_initcall+0x30/0x1b0) from [<c00083f4>] (kernel_init+0xa4/0x11c)
[<c00083f4>] (kernel_init+0xa4/0x11c) from [<c0023f3c>] (kernel_thread_exit+0x0/0x8)
---[ end trace 1b75b31a2719ed1c ]---
This issue is caused by using gpio pin without request. Add gpio_request()
into zylonite. To simplify the code, error checking is omitted since this
is being performed early.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Removed the LBD support that isn't of any use right now at least,
then remove remnants of the TCM config flags that somehow crept
in by mistake (not yet merged patch for 2.6.32) and then the usual
defconfig noise from updated menus.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add keypad multi-function pin api for w90p910 platform.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add HAVE_CLK depends on for w90p910 platform.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add missing register defines for ep93xx keypad clock support.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change the reg argument of the ep93xx_syscon_swlocked_write function
to be an __iomem pointer. Fixes a number of build warnings.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix a number of build errors in ep93xx gpio.c due to to missing irq.h
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MAC address for the ep93xx ethernet driver can be optionally
copied from registers in the controller when booting. Due to
[ARM] 5573/1: ep93xx: ensure typesafe io, the cast for the source
address is no longer needed.
EP93XX_ETHERNET_BASE is typed as a (void __iomem __force *) so
memcpy_fromio() needs to be used instead of memcpy().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The EP93XX_VIC{1/2}_BASE defines are now typesafe due to
[ARM] 5573/1: ep93xx: ensure typesafe io. The (void *) cast
is not needed when calling vic_init().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For future compatibility, we need to ensure that swap and file Linux
PTEs conform with the hardware PTEs "fault" encoding. Swap PTEs
already fit in with this, but file PTEs do not. Shift them by one
bit to ensure that they conform, using bit 2 to distinguish between
swap and file PTEs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These old symbols are meaningless now that we have memory type
support implemented. The entire memory type field needs to be
modified rather than just a few bits twiddled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull the initial preempt_count value into a single
definition site.
Maintainers for: alpha, ia64 and m68k, please have a look,
your arch code is funny.
The header magic is a bit odd, but similar to the KERNEL_DS
one, CPP waits with expanding these macros until the
INIT_THREAD_INFO macro itself is expanded, which is in
arch/*/kernel/init_task.c where we've already included
sched.h so we're good.
Cc: tony.luck@intel.com
Cc: rth@twiddle.net
Cc: geert@linux-m68k.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The WM8731 driver has been updated to allow registration via normal
device model methods rather than from within the ASoC driver probe
so update the AT91SAM9G20-EK to make use of this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add group irq enable/disable for w90p910 platform.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes the VIC resume from suspend flagged IRQ:s identical to
the flags indicating all possible interrupts. This is perhaps not
the optimal setting but setting it to 0 makes the system suspend
and never come back again (all IRQ sources masked off).
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To ensure typesafe io, the enable_reg variable should be a
void __iomem pointer not u32.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-ep93xx/include/mach/hardware.h
1. Properly name the include files so that they are loaded
from the <mach/*> directory and not the local directory.
2. Remove including the ts72xx.h header. This header is not
generic to the ep93xx platform. It should only be included
by the ts72xx specific files that require it. The only
two users in the tree are arch/arm/mach-ep93xx/ts72xx.c
and drivers/mtd/nand/ts7250.c.
arch/arm/mach-ep93xx/include/mach/ts72xx.h
1. <linux/io.h> should already be included by any user of this
header. Doing the include here hides it from being needed
by the calling source file.
arch/arm/mach-ep93xx/core.c
1. Remove unnecessary headers. They were probably included
originally due to cut-and-paste from other files.
2. <linux/io.h> should be included not <mach/gpio.h>
arch/arm/mach-ep93xx/adsphere.c
arch/arm/mach-ep93xx/edb93xx.c
arch/arm/mach-ep93xx/gesbc9312.c
arch/arm/mach-ep93xx/micro9.c
arch/arm/mach-ep93xx/ts72xx.c
1. Remove unnecessary headers.
arch/arm/mach-ep93xx/ts72xx.c
1. Remove unnecessary headers.
2. Add platform specific header <mach/ts72xx.h>.
drivers/mtd/nand/ts7250.c
1. <linux/io.h> should be included not <asm/io.h>.
2. Add platform specific header <mach/ts72xx.h>.
Cc: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
<linux/io.h> was getting included by <mach/ts72xx.h>, is should be
included by this file.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add clkdev support for the ep93xx_keypad driver.
A matrix keypad driver for the ep93xx just got merged via the
input subsystem group. For this driver to work the keypad clock
needs to be added to the ep93xx clkdev support. In order to
accomplish this the following changes are implemented:
1) Move the EP93XX_EXT_*_RATE defines to mach/include/hardware.h.
2) Add EP93XX_KEYTCHCLK_DIV{4/16} for the keypad driver.
3) Add support for programmable clocks (set_rate() callback).
4) Add clk_keypad for the keypad driver.
5) tab indent the clk_lookup table for easier reading.
6) Add the set_rate() callback to program the keypad clock.
This callback is generalized since the ADC clock (touchscreen)
can use the same callback.
7) Use the ep93xx_syscon_swlocked_write() core function for updating
the software locked register.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add core functions to handle writes to the ep93xx software locked
registers.
There are a number of registers in the EP93xx System Controller
that require a write to the software lock register before they
can be updated. This patch adds a number of exported functions
to the ep93xx core that handle this access.
The software locked clock divider registers, VidClkDiv, MIRClkDiv,
I2SClkDiv and KeyTchClkDiv would typically involve writing a
specific value to the register. To support this the
ep93xx_syscon_swlocked_write() function is provided.
For the DeviceCfg register it's more typical to only need to
set or clear a single bit. A generic ep93xx_devcfg_set_clear()
function is provided to handle both operations. Two inline
functions, ep93xx_devcfg_set_bits() and ep93xx_devcfg_clear_bits()
are also provided to improve code readability.
In addition, the remaining bits in the System Controller Device
Config Register have been documented and the previously defined
names shortened.
All code paths that use this functionality have been updated
except for arch/arm/kernel/crunch.c. That code is in a context
switch path, which is not reentrant, so it is safe against itself.
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add and initialize the gpio_wp and gpio_cd members. We need to
ensure that all users are covered, because GPIO 0 may be valid.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Attepmpt to configure ULPI pins gives the following compile error:
CC arch/arm/mach-pxa/cm-x300.o
arch/arm/mach-pxa/cm-x300.c:155: error: 'MFP_MFP_AF0' undeclared here (not in a function)
arch/arm/mach-pxa/cm-x300.c:155: error: 'MFP_MFP_DS01X' undeclared here (not in a function)
make[2]: *** [arch/arm/mach-pxa/cm-x300.o] Error 1
make[1]: *** [arch/arm/mach-pxa] Error 2
make: *** [sub-make] Error 2
Fix it.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Document the layout of our swp PTE entries, adding definitions for
the bit masks/shifts/sizes, and implement MAX_SWAPFILES_CHECK()
such that we fail to build if we are unable to properly encode the
swp type field.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now required for libsas:
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Building modules, stage 2.
MODPOST 1096 modules
ERROR: "xscale_flush_kern_dcache_page" [drivers/scsi/libsas/libsas.ko] undefined!
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As slab is available early now, use kzalloc() rather than
alloc_bootmem_low() in pxa_init_gpio_chip().
This removes the following boot time warning:
<4>------------[ cut here ]------------
<4>WARNING: at mm/bootmem.c:535 alloc_arch_preferred_bootmem+0x2c/0x54()
<d>Modules linked in:
[<c0029430>] (unwind_backtrace+0x0/0xdc) from [<c0036f64>] (warn_slowpath_common+0x4c/0x80)
[<c0036f64>] (warn_slowpath_common+0x4c/0x80) from [<c000ede0>] (alloc_arch_preferred_bootmem+0x2c/0x54)
[<c000ede0>] (alloc_arch_preferred_bootmem+0x2c/0x54) from [<c000f2e4>] (___alloc_bootmem_nopanic+0x34/0xd0)
[<c000f2e4>] (___alloc_bootmem_nopanic+0x34/0xd0) from [<c000f6e4>] (___alloc_bootmem+0xc/0x34)
[<c000f6e4>] (___alloc_bootmem+0xc/0x34) from [<c000cb20>] (pxa_init_gpio+0x48/0x228)
[<c000cb20>] (pxa_init_gpio+0x48/0x228) from [<c0009794>] (init_IRQ+0x34/0x44)
[<c0009794>] (init_IRQ+0x34/0x44) from [<c00089d4>] (start_kernel+0x144/0x264)
[<c00089d4>] (start_kernel+0x144/0x264) from [<a0008034>] (0xa0008034)
<4>---[ end trace 1b75b31a2719ed1c ]---
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
In commit f23d491131, the pwr-i2c device name changed due to the
newly introduced device table. This patch fixes the clock so the
driver's probe will succeed again.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The default configuration file for the KwikByte kb9202 board was based on a 2.6.13-rc2 kernel and doesn't produce a bootable kernel. Update the
configuration in order to produce a bootable image.
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the basic infrastructure for the Nomadik 8815
CPU and the "Nomadik Hardware Kit" NHK8815. This patch only
includes the serial console and core stuff, no drivers.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PrimeCell Vectored Interrupt Controller offers a way to trigger
any interrupt through software. This is a useful tool for developing,
but such software interrupt can only be acked by writing a bit in the
"software clear" register, or the handler will loop forever. This
splits ack from mask, and acks the soft irq in case it was the source.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Nomadik SoC (not yet merged) has a modified PL090 VIC cell. This adds
support for it by reading the PrimeCell ID at the end of the page and
calling a separate init function.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds a few default locks to the clocks (the clocks were used
before the locks were initialized by code), then renames the clocks
a bit to fit with the latest driver names (some changed during
review). Lastly it moves the initialization of the clock debugfs
entry to module_init() initcall level since the debugfs isn't up
in core_initcall().
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This defconfig update selects all the new U300 drivers merged for
2.6.31-rc1 in the merge window and add defaults for the new
config options. It compiles and boots nicely from initramfs on
the U300.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Hong Xu <hong.xu@atmel.com>
Here are the modification to at91sam9261 files dedicated to the support of
at91sam9g10. This direction has been adopted to minimize code duplication.
All at91sam9261 drivers are enabled in _devices and board- files. Modificaton
to peripherals that support at91sam9g10 will be added in future patches.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Hong Xu <hong.xu@atmel.com>
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Here is the basic header file support for this product.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Hong Xu <hong.xu@atmel.com>
Add the at91sam9g10 support to the AT91 generic clock file. It takes
advantage of the management by functionalities of those PLLs and clocks.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds input keyboard gpio support on at91sam9g20ek board.
It adds button 3 and 4.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here are the at91 specific files dedicated to the at91sam9g45 series. They
mimic the traditional at91 way of managing chips & boards.
The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES. In
the future, the main board for this 9g45 series will be the
AT91SAM9M10G45-EK (I choose this last name for the board file).
Simple drivers are enabled in _devices and board- files. Newer peripheral
support will be added in future patches.
Incuded peripherals support (for now):
- USART
- SPI
- Ethernet
- NAND flash
- LCD
- gpio/joystick/buttons
- leds and pwm
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embedds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.
Here is the basic header file support for this product series.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the at91sam9g45 series support to the AT91 generic clock file.
This takes care of the particularities of the PMC for this series.
It also takes advantage of the management by functionalities of
those PLLs and clocks.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove at91_gpiolib_request. It returns -EPERM if a request pin is not
in GPIO mode, however we want to be able to gpio_request alternative
function pins to reserve them, and in some cases we need to be able to
use the gpiolib functions on alternative function pins.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds input keyboard gpio support on at91sam9rlek board. It adds button 1
and 2 (left and right click).
It also adds gpio leds ds1, ds2 and ds3.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here is a little update to the at91sam9rlek lcd interface.
This will correct the power pin of the LCD.
It will also add precision to the struct atmel_lcdfb_info
scructure: backlight enabling and wiring mode correction:
RGB wiring on the -EK board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ep93xx: Show gpio interrupt type in debugfs output.
EP93xx uses a private implementation for the debugfs output.
Modify this output so it includes the interrupt type when the
gpio is configured as an interrupt
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix ep93xx gpio.c header includes and __iomem pointers.
1. <linux/gpio.h> should be included instead of <asm/gpio.h>
2. <mach/hardware.h> should be included instead of <mach/ep93xx-regs.h>
3. data_reg and data_dir_reg in struct ep93xx_gpio_chip should be
void __iomem pointers not unsigned int
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM: ep93xx: ensure typesafe io
For the ep93xx platform, all EP93XX_*_BASE defines are based
on virtual addresses. Ensure that all these defines are
properly typesafe for the __raw_{read/write}* macros.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the link script for ARM to use PAGE_SIZE instead of hard-
coded 4096. Also the old RODATA macro is deprecated
for the RO_DATA(PAGE_SIZE) macro. As a consequence the PAGE_SIZE
was changed from (1UL << PAGE_SHIFT) to (_AC(1,UL) << PAGE_SHIFT)
because the linker does not understand the "UL" suffix to numeric
constants.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
handle_bad_irq() expects the IRQ number to be valid (used for statistics),
so it cannot be called with an illegal vector. The problem was reported
by a static analysis tool.
The change makes bad_irq_desc redundant, so delete it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes two errors we get when building GTA02 kernel.
~ use_bbt is incorrect, we need flash_bbt.
~ We do not need .force_soft_ecc because we can unset
CONFIG_MTD_NAND_S3C2410_HWECC.
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: updated patch description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The commit 9db41f9edc added
the .flash_bbt flag to the nand set, so add this back into
the mach-mini2440.c file (taken out on initial commit to
allow build).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit 52da219e96 added IIS
platform devices, but these do not build on s3c24xx systems
and the file depends on SND_S3C24XX_SOC, which is selected
for all S3C64XX/S3C24XX systems.
As a quick fix, make the dev-audio.o file depends on
SND_S3C64XX_SOC_I2S instead.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit 52da219e96 removed
the s3c_device_iis, but didn't replace it with anything
so a number of s3c24xx machines are currently failing
to build.
As a temporary fix, re-instate s3c_device_iis until a
proper replacement can be done for it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The commit ec976d6eb0
removed a number of gpio definitions from <mach/hardware.h>
but misssed updating these two files:
Fix the following build errors by including <linux/gpio.h>:
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c: In function 's3c24xx_spi_gpiocfg_bus1_gpg5_6_7':
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c:25: error: implicit declaration of function 's3c2410_gpio_cfgpin'
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c:28: error: implicit declaration of function 's3c2410_gpio_pullup'
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c: In function 's3c24xx_spi_gpiocfg_bus0_gpe11_12_13':
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c:25: error: implicit declaration of function 's3c2410_gpio_cfgpin'
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c:28: error: implicit declaration of function 's3c2410_gpio_pullup'
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The "EET" variant of the pcm037 board has an OLED display, using a S6E63D6
display controller on the first SPI interface, using GPIO57 as a chip-select
for it. S6E63D6 is initialised in the boot-loader, so we only have to take care
of the LCD. EET also adds several buttons and LEDs on GPIOs. This patch adds a
"pcm037_variant=" kernel command line parameter to specify at boot-time which
board the kernel is running on, default is "pcm970", specify "eet" for the EET
board.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for the MT9T031 CMOS camera sensor from Aptina to the PCM037
board. Also add two I2C iomux pin definitions, needed for pcm037. Also
remove now unneeded #ifdef CONFIG_I2C_IMX.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since recent mxc_nand driver fixes from linux-mtd this patch
add support for ST NAND02GW3B2CN6 (2k pages flash) placed on the armadillo 500
motherboard.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch add support for NOR flash mapping through the physmap driver.
The purpose is to maintain the original Atmark partition model.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove the unused CONFIG_DEBUG_S3C_PORT as we currently only have
support for using the S3C UARTs via the low-level debug code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
CONFIG_S3C24XX_PWM was defined in arch/arm/plat-s3c24xx/Kconfig but
not used anywhere else as the corresponding makefile used
CONFIG_HAVE_PWM (selected by CONFIG_S3C24XX_PWM) to compile the PWM
driver.
Change the makefile to use CONFIG_S3C24XX_PWM to compile this driver
to ensure it is only build when needed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Some bootloader may initialize debounce register and this will make
dbclk not consist with the debounce register after linux kernel boot
up.
Signed-off-by: janboe <janboe.ye@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The function flush_iotlb_page is not loading the CAM register with
the correct entry to be flushed, so it is flushing other entry
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use async timings when sync timings are not requested.
Also ensure that OneNAND is in async mode when async
timings are used.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enables MStandby smart-idle mode, autoidle smartidle mode,
and the autoidle bit for DMA4_OCP_SYSCONFIG.
Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.deeprootsystems.com>
SRAM size fix for HS/EMU devices
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap_type() function is added and returns the DEVICETYPE field of
the CONTROL_STATUS register. The result can be used for conditional
code based on whether device is GP (general purpose), EMU or
HS (high security). Also move the type defines so omap1 code
compile does not require ifdefs for sections using these defines.
This code is needed for the following fix to set the SRAM
size correctly for HS omaps. Also at least PM and watchdog
code will need this function.
Signed-off-by: Kevin Hilman <khilman@ti.deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
platform_get_irq may return -ENXIO. but struct omap_mbox mbox_dsp_info.irq
is unsigned, so the error was not noticed.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
twl_mmc23_set_power() has MMC2 twl_mmc_controller hardcoded in it, which
breaks MMC3. Find the right controller to use instead.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some of the N770's MMC configuration options seem to have been
dropped. This patch adds them back in again.
Note that only the .ocr_mask change was /critical/, but I've added the
.max_freq setting back as well, as the original sources had it. Can
anyone confirm if this is unnecessary?
Secondly, there is support in the original code for a 4wire/higher
speed mode. As I don't have the requisite N770 hardware (I think it
was a rev2 N770?) to test this, I can't really add it back.
Signed-off-by: Andrew de Quincey <adq@lidskialf.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes the positioning of " in MODULE_AUTHOR, which is currently
causing a build failure on latest git with CONFIG_OMAP_MBOX_FWK=m; the
original breakage appears to date from the end of last year in
a5abbbe52b7e89a7633319c5417bd4331f7ac8ed
Signed-Off-By: Jonathan McDowell <noodles@earth.li>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.infradead.org/mtd-2.6: (63 commits)
mtd: OneNAND: Allow setting of boundary information when built as module
jffs2: leaking jffs2_summary in function jffs2_scan_medium
mtd: nand: Fix memory leak on txx9ndfmc probe failure.
mtd: orion_nand: use burst reads with double word accesses
mtd/nand: s3c6400 support for s3c2410 driver
[MTD] [NAND] S3C2410: Use DIV_ROUND_UP
[MTD] [NAND] S3C2410: Deal with unaligned lengths in S3C2440 buffer read/write
[MTD] [NAND] S3C2410: Allow the machine code to get the BBT table from NAND
[MTD] [NAND] S3C2410: Added a kerneldoc for s3c2410_nand_set
mtd: physmap_of: Add multiple regions and concatenation support
mtd: nand: max_retries off by one in mxc_nand
mtd: nand: s3c2410_nand_setrate(): use correct macros for 2412/2440
mtd: onenand: add bbt_wait & unlock_all as replaceable for some platform
mtd: Flex-OneNAND support
mtd: nand: add OMAP2/OMAP3 NAND driver
mtd: maps: Blackfin async: fix memory leaks in probe/remove funcs
mtd: uclinux: mark local stuff static
mtd: uclinux: do not allow to be built as a module
mtd: uclinux: allow systems to override map addr/size
mtd: blackfin NFC: fix hang when using NAND on BF527-EZKITs
...
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (49 commits)
[ARM] idle: clean up pm_idle calling, obey hlt_counter
[ARM] S3C: Fix gpio-config off-by-one bug
[ARM] S3C64XX: add to_irq() support for EINT() GPIO
[ARM] S3C64XX: clock.c: fix typo in usb-host clock ctrlbit
[ARM] S3C64XX: fix HCLK gate defines
[ARM] Update mach-types
[ARM] wire up rt_tgsigqueueinfo and perf_counter_open
OMAP2 clock/powerdomain: off by 1 error in loop timeout comparisons
OMAP3 SDRC: set FIXEDDELAY when disabling SDRC DLL
OMAP3: Add support for DPLL3 divisor values higher than 2
OMAP3 SRAM: convert SRAM code to use macros rather than magic numbers
OMAP3 SRAM: add more comments on the SRAM code
OMAP3 clock/SDRC: program SDRC_MR register during SDRC clock change
OMAP3 clock: add a short delay when lowering CORE clk rate
OMAP3 clock: initialize SDRC timings at kernel start
OMAP3 clock: remove wait for DPLL3 M2 clock to stabilize
[ARM] Add old Feroceon support to compressed/head.S
[ARM] 5559/1: Limit the stack unwinding caused by a kthread exit
[ARM] 5558/1: Add extra checks to ARM unwinder to avoid tracing corrupt stacks
[ARM] 5557/1: Discard some ARM.ex*.*exit.text sections when !HOTPLUG or !HOTPLUG_CPU
...
pm_idle is used by infrastructure (eg, cpuidle) which expects architectures
to call it in a certain way. Arrange for ARM to follow x86's lead on this
and call pm_idle() with interrupts already disabled. However, we expect
pm_idle() to enable interrupts before it returns.
Also, OMAP wants to be able to disable hlt-ing, so allow hlt_counter to
prevent all calls to pm_idle.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix gpio-config off-by-one bug. Without this patch, touching GPA0 pin on
S3C64XX platform causes kernel oops.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
N group
Add to_irq() function to onvert gpio to irq for external interrupt
group (GPN).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The usb-host clock was using the wrong define (the SCLK enable for the
usb-host-bus) to change the HCLK register instead of the HCLK_UHOST bit.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
A few typos seems to have sneaked into the HCLK gate defines, causing the
usb host clock to not get enabled. Fix them according to the reference
manual and throw in the 3d accel bit for good measure.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This allows the callers to now pass down the full set of FAULT_FLAG_xyz
flags to handle_mm_fault(). All callers have been (mechanically)
converted to the new calling convention, there's almost certainly room
for architectures to clean up their code and then add FAULT_FLAG_RETRY
when that support is added.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
