When filling data->als_contr, the register content read into status needs
to be used, instead of the return status value of regmap_read.
Fixes: 8592a7eefa ("iio: ltr501: Add support for ltr559 chip")
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support to calculate lux value from visible
and IR spectrum adc count values. Also added IIO_LIGHT
channel to enable user read the lux value directly
from device using illuminance input ABI.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently, proximity sensor boundary check is done
inside the switch block but outside the case
statement.Since this code will never get executed,
moved the check outside the switch case statement.
867 case IIO_PROXIMITY:
868 switch (dir) {
// Following line has been moved outside the switch block.
869 if (val > LTR501_PS_THRESH_MASK)
870 return -EINVAL;
871 case IIO_EV_DIR_RISING:
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Clearly the intent was to error if the value was not 0 or 1.
As implemented we have (A != 0 || A != 1) which is always true
as A is never both 0 and 1 at the same time.
As the autobuilder suggested, && makes more sense for this error
check.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for Liteon 301 Ambient light sensor. Since
LTR-301 and LTR-501 are register compatible(and even have same
part id), LTR-501 driver has been extended to support both
devices. LTR-501 is similar to LTR-301 in ALS sensing, But the
only difference is, LTR-501 also supports proximity sensing.
LTR-501 - ALS + Proximity combo
LTR-301 - ALS sensor.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This device is register compatible with LTR501, with a minor difference for
ALS control register as showed below:
ALS Control register for LTR501:
7 6 5 4 3 2 1 0
+------+------+------+------+------+------+------+------+
| | | | |
| Reserved | Gain | SW | ALS Mode |
| | | Reset| |
+------+------+------+------+------+------+------+------+
ALS Control register for LTR559:
7 6 5 4 3 2 1 0
+------+------+------+------+------+------+------+------+
| | | | |
| Reserved | Gain | SW | ALS |
| | | Reset| Mode |
+------+------+------+------+------+------+------+------+
We handle this difference by introducing ltr501_chip_info.
Datasheet for LTR559 is at:
http://optoelectronics.liteon.com/upload/download/DS86-2013-0003/S_110_LTR-559ALS-01_DS_V1.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added ACPI enumeration support for LTR501 chip.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added rate control support for ALS and proximity
threshold interrupts.Also, Added support to modify
and read ALS & proximity sensor sampling frequency.
LTR-501 supports interrupt rate control using persistence
register settings. Writing <n> to persistence register
would generate interrupt only if there are <n> consecutive
data values outside the threshold range.
Since we don't have any existing ABI's to directly
control the persistence register count, we have implemented
the rate control using IIO_EV_INFO_PERIOD. _period event
attribute represents the amount of time in seconds an
event should be true for the device to generate the
interrupt. So using _period value and device frequency,
persistence count is calculated in driver using following
logic.
count = period / measurement_rate
If the given period is not a multiple of measurement rate then
we round up the value to next multiple.
This patch also handles change to persistence count whenever
there is change in frequency.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds interrupt support for Liteon 501 chip.
Interrupt will be generated whenever ALS or proximity
data exceeds values given in upper and lower threshold
register settings.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support to modify and read ALS integration time.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added regmap support. It will be useful to handle
bitwise updates to als & ps control registers.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This makes ltr501 code consistent with the coding style adopted
for the new drivers added to IIO.
We prepare the path for adding support for LTR559 chip.
Reported by checkpatch.pl
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Power down device when an error occurs in order to avoid wasting
power. Move powerdown function up to be seen by the new call and
align parameters for the ltr501_write_contr() call.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
combined ambient light (two channels) and proximity sensor with I2C
interface; the ALS channels are visible+IR and IR
datasheet is here
http://optoelectronics.liteon.com/upload/download/DS86-2012-0006/P_100_LTR-501ALS-01_PrelimDS_ver1.1.pdf
v3:
* fix use of sizeof in _read_als()
v2: (thanks to Lars-Peter Clausen)
* cannot use devm_iio_device_register() due to cleanup order in _remove()
* mutex around data wait/read
* turn info message in _probe() into check for part number
* change copyright year to 2014
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
