On new Intel platforms like ApolloLake, legacy interrupt mechanism
(INTx) is not supported, so WLAN modules are not working because
interrupts are missing, therefore this patch is to add MSI support to
ath9k. With module paremeter "use_msi=1", ath9k driver would try to
use MSI instead of INTx.
Signed-off-by: Russell Hu <rhu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add bits definition for AR_BT_COEX_MODE2 and AR_BT_COEX_MODE3, which
needed by SOC chips (AR9340, AR9531, AR9550, AR9561).
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make ath_init_leds() and ath_deinit_leds() pairs as the only
API to set leds, also removed direction configuration from
ath9k_start() and ath9k_stop(). So the initial is more clear
now.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Define correct GPIO numbers and MASK bits to indicate the WMAC
GPIO resource.
Allow SOC chips(AR9340, AR9531, AR9550, AR9561) to access all GPIOs
which rely on gpiolib framework. But restrict SOC AR9330 only to
access WMAC GPIO which has the same design with the old chips.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One crash issue be found on ar9300: RTC_RC reg read leads crash, leading
the data bus error, due to RTC_RC reg write not happen properly.
Warm Reset trigger in continuous beacon stuck for one of the customer for
other chip, noticed the MAC was stuck in RTC reset. After analysis noticed
DMA did not complete when RTC was put in reset.
So, before resetting the MAC need to make sure there are no pending DMA
transactions because this reset does not reset all parts of the chip.
The 12th and 11th bit of MAC _DMA_CFG register used to do that.
12 cfg_halt_ack 0x0
0 DMA has not yet halted
1 DMA has halted
11 cfg_halt_req 0x0
0 DMA logic operates normally
1 Request DMA logic to stop so software can reset the MAC
The Bit [12] of this register indicates when the halt has taken effect or
not. the DMA halt IS NOT recoverable; once software sets bit [11] to
request a DMA halt, software must wait for bit [12] to be set and reset
the MAC.
So, the same thing we implemented for ar9580 chip.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ar9550 or later chips, the AR_GPIO_IN_OUT register only can
control GPIO[0:3]. For the extra GPIO, use standard GPIO calls
instead of WMAC internal registers.
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Chips in the AR9003 family have a second TSF, which
needs to be cleared when putting the card to
sleep.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This can be used if we need to apply register settings
for all PCOEM solutions (in the AR9003 family).
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add TX power per-rate tables for different MIMO modes (e.g STBC) in order to
cap the maximum TX power value per-rate in the TX descriptor path.
Cap TX power for self generated frames (ACK, RTS/CTS).
Currently TPC is supported just by AR9003 based chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The base TSF is used for HW timers 0..7, but chips
in the AR9003 family and above can support more generic
timers. To use them, however, a second HW TSF needs to
be enabled. This patch allows usage of the extra
timers by starting the second TSF properly.
The extra set of HW timers is apparently also present
in AR9287, but we enable it only for the AR9003 family.
Cc: Kobi Cohen-Arazi <kobic@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The initvals use up quite a bit of space, and PC-OEM support is
typically not needed on embedded systems
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR934x and newer SoC devices, the layout of the AR_RTC_PLL_CONTROL
register changed. This currently breaks at least 5/10 MHz operation.
AR933x uses the old layout.
It might also have been causing other stability issues because of the
different location of the PLL_BYPASS bit which needs to be set during
PLL clock initialization.
This patch also removes more instances of hardcoded register values in
favor of properly computed ones with the PLL_BYPASS bit added.
Reported-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR934x rev 3, settin the ad-hoc flag completely messes up hardware
state - beacons get stuck, almost no packets make it out, hardware is
constantly reset.
When leaving out that flag and setting up the hw like in AP mode, TSF
timers won't be automatically synced, but at least the rest works.
AR934x rev 2 and older are not affected by this bug
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The data transmission to the power save station should be aborted
immediately, whenever the station informs sleep state. Right now
the frames queued into into hardware are being transmitted until
the hardware detects the power save station based excessive retries
of the data frames due to unacknowlegdement. Then remaining frames
are returned with filetered status and might be retried later by
driver or mac80211.
Per WFA certification testing, AP should not send out more than two
frames after processing nullfunc with PM bit set from associated
station. To speed up tx filtering, the pending frames in hardware
queues for given station will be aborted immediately via tx filter
registers. This transmit filters can be ignored if the descriptor
is having invalid destination index or clear destination mask set.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Program the required baseband watchdog interrupt
mask to ensure that the correct watchdog interrupts
are raised when the BB is hung for some reason.
Also, use the capability HW_BB_WATCHDOG instead of
relying on other flags.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR934x v1.3 no longer needs the DCU backoff reduction workaround for
preventing rx overruns, but in turn needs the number of usable Tx
buffers to be reduced slightly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a local bus timeout has been detected, the host interface needs to be
reset to clear the errors. AR934x uses a different synchronous interrupt
bit to indicate this, so the check needs to be fixed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Preparation for updating common->macaddr along with virtual interface
MAC address changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Improves stability on affected devices and also fixes the Tx IQ calibration
related regression on some AR9340 devices such as the TP-Link TL-WDR4300.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever WLAN receives scheduling msg from BT, it reduces tx power
based on RSSI level. And then BT starts simultaneous transmission
along with WLAN. Sometimes HW MAC compares tx power that is used
prior to power reduction which is causing BT transmission to defer.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And recognize the device in the init path.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the CONT_* and LNA_* messages from
AR_MCI_INTERRUPT_RX_MSG_DEFAULT. Those MCI rx messages only
meant for debugging purpose. Including them in default rx_msg
series could raise huge amount of MCI interrupts when BT traffic
is going on. And also it increases power consumption when WLAN
is scanning.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some register values of bit shifts are corrected in order to support the upcoming
transmission power control (tpc) for control packets as well.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WLAN driver initialization is muting BT which is terminating
the ongoing BT traffic. The reason to mute BT is to avoid any
incoming MCI messages from BT when MCI reset is in progress that
could corrupt WLAN MCI RX state machine. But we should not
dedicate radio completely to WLAN in driver init itself. So this
patch removes the wlan weightage changes from mute BT to retain
BT connection.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable WLAN and BT mode for switching regulator discontinuous
orverride for AR9462 chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tested in AR9462 Rev:2, both hardware capability flag are set
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
v1.0 chips are not available in the market.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
send halt BT GPM if the chip is in network sleep and BT state
is awake
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
these definitions will be used by MCI state machine and the corresponding
hardware code
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove all wlan weight macros and group it together for better
understanding & readability. It makes the code reusable for
AR9462 wlan weights.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Renamed to be in sync with Marketing term and to avoid
confusion with other chip names.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Supported calibrations of radio retention table (RTT) are
- DC offset
- Filter
- Peak detect
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
