Add the ability to advertise that the device
contains the AP SME and what features it can
support. There are currently no features in
the bitmap -- probe response offload will be
advertised by a few patches Arik is working
on now (who took over from Guy Eilam) and a
device with AP SME will typically implement
and require response offload.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add interface address so it can be mapped to a local
interface. Add max-ampdu and mpdu-density.
Print out the tid->baw_size
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on a quick test, TDLS seemed to be working fine with ath9k, so
let's start advertising support for this in the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The initval tables are updated as per system team input to improve
rx performance and power accuracy at 5GHz.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9462 chips have the capabilities to provoide bluetooth
profile information. For non-AR9462 btcoex chips, the BT
priority traffic was identified by periodically polling
the respective registers and updated dutycycle, stomptype,
etc. As AR9462 chip offers the BT profile informations,
let us make use of that to update aggregation limit,
dutycycle, stomptype and wieghtages.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To improve CCK sensitivity for AR9462 chips, performing
spur mitigation at 2440, 2464 frequencies alone is sufficient.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code here treats very large values of "limit" as less than
MAX_POWER_RATE because of the cast to int. We should do the compare
as u32 instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During the fast channel change noise floor values are being loaded
twice at init_cal and after channel_change. The commit "ath9k_hw:
Improve fast channel change for AR9003 chips" overlooked it that
caused failure to load nf while doing bgscan. This patch performs noise
floor calibration after the fast and full reset.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes system hang when resuming from S3 state
and lower rate sens failure issue.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the driver did not care if TX_CTL_REQ_TX_STATUS
was set on aggregated frames or not and it would silently
drop successfully sent frames if possible [much like:
"no news is good news!"].
But, TX_CTL_REQ_TX_STATUS was invented for a reason and
no tx status report should ever be dropped if it is set.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit ce407afc10 introduced regression for AR9330/AR9340
register offsets. Some of the register offsets are common
for AR9330/AR9340/AR9485 except AR9380. Fix that.
Cc: stable@kernel.org [3.1.0+]
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IQ calibration during fast channel change sometimes failed
with RTT. And also restoring invalid radio retention readings
during init cal could cause failure to set the channel properly.
This patch counts the valid rtt history readings and clears
rtt mask.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My recent commits (3782c69d, 324c74a) introduced regression
for register offset selection that based on the macversion.
Not using parentheses in proper manner for ternary operator
leads to select wrong offset for the registers.
This issue was observed with AR9462 chip that immediate disconnect
after the association with the following message
ieee80211 phy3: wlan0: Failed to send nullfunc to AP 00:23:69:12:ea:47
after 500ms, disconnecting.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Renamed to be in sync with Marketing term and to avoid
confusion with other chip names.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR946/8x chips are 2x2 Dual band with BT support. In order
to avoid misleading with other chips and to be in sync with
marketing team's term, AR9480 is renamed as AR9462.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support the fast channel change across band switch only when there
are available of reusable cabliration results. And also observed that
doing agc control calibration on fastcc, sometimes causing calibration
timeout. Hence changing agc control to be run only on full chip reset.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Supported calibrations of radio retention table (RTT) are
- DC offset
- Filter
- Peak detect
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To improve sensitivity for AR9480, the normal and minimum
noise floor values of both bands are updated.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: Improve fast channel change for AR9003 chips"
fixes the fast channel change issue for AR9003 chips that was
originally observed in AR9382 chip. Hence enabling fastcc support
again for 11A channel for AR9003 chips.
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently Tx IQ calibration is enabled by default for all AR9003
chips. But for AR9480, the calibration status should be read from
chip after processing ini. And also the carrier leak calibration
status is checked during init cal. As the init_cal is being called
for fast channel change too, the tx_cl status only be read after
full reset. Hence moving that into process ini function.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to reuse Carrier leak calibration
during fast channel change for AR9480 chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass an argument to decide whether to reuse the Tx IQ
calibration measurements or not during fast channel change.
This will be later used by MCI support for AR9480.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to reduce the overall scan time, fast channel change
should be implemented properly. This patch adds fast channel
change support across band switch or channel mode switch
instead of doing full chip reset. During the fastcc, tx iqcal
measurements are preserved and will be reloaded after successful
the channel change.
This patch also addressed fast channel issue where the STA can not
see APs in higher than operating channel on 5GHz band after
the association.
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 5G Tx gain table w/ XPA is updated to improve spur
performance in high_power Tx gain table.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ar9003 table is updated to increase XLNA BIAS
output driver strengh.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because of not clearing Bit 14 of AR_WA, the ASPM L1 is not
enabled when entering into sleep mode. AR9480 does not need
bit 14 to be set.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevents lots of broken frames from showing up on monitor interfaces
by default.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: Fix incorrect key_miss handling" changed the code
to only report key miss errors if a MIC error wasn't reported.
When checking the flags in that order in the MAC code, it might miss some
real events, because the value of the MIC error flag is undefined under
some conditions.
The primary issue addressed by the previous commit is making sure that
MIC errors are properly reported on the STA side. This can be fixed in
a better way by adding a separate rx status flag for key miss and
ignoring it for multicast frames.
This fix slightly improves stability in AP mode on some older hardware,
like AR9132.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is unused since the previous dead code that was using it had been
removed earlier.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code for handling various restrictions concerning regulatory limits,
antenna gain, etc. is very convoluted and duplicated across various
EEPROM parsing implementations, making it hard to review.
This patch partially cleans up the mess by unifying regulatory limit
handling in one function and simplifying handling of antenna gain.
It also removes unused transmit power scaling arrays from the EEPROM code,
which belonged to an unimplemented API that isn't supposed to be in
the driver anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PHY errors relevant for ANI are always tracked by hardware counters, the
bits that allow them to pass through the rx filter are independent of that.
Enabling PHY errors in the rx filter often creates lots of useless DMA traffic
and might be responsible for some of the rx dma stop failure warnings.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When tx is suspended temporarily and the queue is flushed, do not increase
the retry count or attempt to send out BAR frames. Instead simply retry
the affected subframes normally after the reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not increment the retry counter if packets to a sleeping station
were not sent because of tx failure, instead of only checking the filter
flag.
Clear the PS filter only after an A-MPDU was reported as filtered,
otherwise the hardware might do some unnecessary extra retransmissions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export how many times each of the reset triggers has fired through debugfs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If "axq_qnum >= ARRAY_SIZE(sc->tx.txq)", then the call to
ath9k_hw_releasetxqueue() would read beyond the end of the ah->txq[]
array and possibly corrupt memory. Fortunately,
ath9k_hw_setuptxqueue() doesn't return high values of "axq_qnum" and
this code can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
th5k_hw_setup_tx_queue() returns a valid offset into the ah->ah_txq[]
array. The ah->ah_txq[] and the ah->txqs[] array are the same size.
Both have AR5K_NUM_TX_QUEUES elements. So this error handling code
will never trigger.
Also it's wrong. The call to ath5k_hw_release_tx_queue() with a qnum
of AR5K_NUM_TX_QUEUES or more will just trigger a WARN_ON() and
return. Or if it missed the WARN_ON(), it would just corrupt some
memory and return.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/ath/ath6kl/cfg80211.o
drivers/net/wireless/ath/ath6kl/cfg80211.c:1838:2: warning: initialization from incompatible pointer type
Caused by commit e9f935e3e8dc0bddd0df6d148165d95925422502...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the AR_SREV register does not seems to indicate whether AR9480 is
pci_express capable or not though the other information like macVersion
etc can be obtained properly. this fix is essential as ASPM won't be intialized
and its related driver functionality ath9k_hw_configpcipowersave won't be
called
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this patch fixes the assumption of maximum number of GPIO pins present
in AR9287/AR9300. this fix is essential as we might encounter some
functionality issues involved in accessing the status of GPIO pins which
are all incorrectly assumed to be not within the range of max_num_gpio
of AR9300/AR9287 chipsets
Cc: stable@kernel.org
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx params should be configured per interface.
add ieee80211_vif param to the conf_tx callback,
and change all the drivers that use this callback.
The following spatch was used:
@rule1@
struct ieee80211_ops ops;
identifier conf_tx_op;
@@
ops.conf_tx = conf_tx_op;
@rule2@
identifier rule1.conf_tx_op;
identifier hw, queue, params;
@@
conf_tx_op (
- struct ieee80211_hw *hw,
+ struct ieee80211_hw *hw, struct ieee80211_vif *vif,
u16 queue,
const struct ieee80211_tx_queue_params *params) {...}
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this extends the bits for rf kill GPIO selection to [7:2] from [4:2] as
we use GPIO pin 11 as rfkill for AR9480 and also remove few unused
macros
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: "Hu, Russell" <rhu@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was reported and tested by Martin Walter over at AVM GmbH Berlin.
This also applies to 3.0.1 so sendint to stable.
Cc: s.kirste@avm.de
Cc: d.friedel@avm.de
Cc: Martin Walter <m.walter@avm.de>
Cc: Peter Grabienski <pgrabien@qca.qualcomm.com>
Cc: stable@kernel.org
Tested-by: Martin Walter <m.walter@avm.de>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes compilation errors when compiling for ARM:
ath6kl/debug.c:312: error: implicit declaration of function 'vmalloc'
ath6kl/debug.c:312: warning: assignment makes pointer from integer without a cast
ath6kl/debug.c:342: error: implicit declaration of function 'vfree'
ath6kl/debug.c:696: warning: assignment makes pointer from integer without a cast
ath6kl/debug.c:871: warning: assignment makes pointer from integer without a cast
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
