There is a race condition between wl1271_tx_work() and the
channel switch, so make sure all the pending packets are
being sent before switching channel.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl12xx uses a single probe response template, regardless of
the probe request.
However, the P2P spec forbids including the p2p ie in some
cases (e.g. the probe request didn't include the p2p ie).
The fw responds only to probe requests that don't
include the p2p ie, and passes up probe requests that
include them (the supplicant will answer them).
Thus, strip the p2p ie from the probe response template.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl12xx uses the beacon as the probe response template.
However, the beacon includes a TIM ie, which shouldn't
exist in the probe response.
Delete it from the skb before configuring the probe
response template.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We were including only 11b rates in IBSS mode. This patch adds OFDM
rates.
[Rephrased commit log and removed one unnecessary comment. -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Due to some changes in PM in recent kernels, the sdio_test module has
been broken for a while. This patch fixes the code that powers the
card on and off.
Also made some small indentation fixes in the Makefile.
[Rephrased commit log and removed the change in the FW name, since
it's done in another patch. -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We were using incorrect max and min dwell times during forced passive
scans because we were still using the active scan states to scan
(passively) the channels that were not marked as passive.
Instead of doing passive scans in active states, we now skip active
states and scan for all channels in passive states.
Cc: <stable@kernel.org> # 2.6.36+
Signed-off-by: Luciano Coelho <coelho@ti.com>
Declare support for p2p interfaces, and create p2p_cli/p2p_go
roles when being asked for.
Indicate we are using a p2p interface by setting the wl->p2p flag.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We set the mac80211 flag for A-MPDU support and also indicate that
Tx-agg session setup is performed in HW.
This patch depends on
"mac80211: add flag to indicate HW only Tx-agg setup support"
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reset the BA state of all connected stations and explicitly clear the
Tx queues. The latter is needed for clearing dummy packets from
tx_queue_count.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Unblock the RX BA constraint event from firmware in AP mode as well.
This allows us to stop RX BA sessions when the FW requests it.
In addition refactor the handler for this event to make the flow
clearer.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When operating as AP track the number of connected stations. When a
single STA is connected don't regulate the PS status of the link.
Since this is the only STA connected, there's no point holding space in
FW for other links. This will speed up communications with a single
connected STA in PSM.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Check a STA is associated before regulating its PS-status in mac80211.
Should never happen, so warn as a precaution.
[Small cosmetic change wrt Kalle Valo's comment. -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Dummy packets are currently only sent on the system_hlid link. The
system_hlid link should never be filtered for PS (as it is not
a STA link). Even so, for correctness, don't indicate dummy packets up.
The skb does not belong to mac80211 and as such does not contain a
correct skb->cb.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
For now, cfg80211 only support match sets with SSIDs, but in the
future more parameters will be added. This patch ignores eventual
matches that do not contain SSIDs in preparation for the future. This
change also affects the case where broadcast SSIDs are used. Matching
a broadcast SSID will match everything, so they can be ignored.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The latest firmware supports up to 16 SSIDs in the scheduled scan
lists. Increase the number we report to cfg80211 and increase the
min/max dwell time to 30 and 60 TUs respectively, because otherwise we
don't have the time to send the probes for all SSIDs.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Implement support for filtering in scheduled scans.
With this commit we now use the match sets passed by cfg80211 to
filter on SSIDs. Due to the nature of the wl12xx firmware API, we
don't allow SSIDs to be sent in the probe requests if they are not
going to match any of the filters.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Declare support for uapsd when working as AP, and
set psd_type and sp_len whan a station is being added.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The driver now support HT properly, so we can always have HT enabled.
Remove the WL12XX_HT configuration.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The firmware only asks for one dummy packet at a time, but sometimes we
are unable to provide it before a FW timer expires. When this happens,
the FW will re-request the dummy packet. If a packet is still queued in
the driver queues, do nothing in this case.
This prevents spurious dummy packets from clogging up the VO AC.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add wl12xx_acx_config_hangover() and respective conf values.
This command configures how long the chip will stay awake
after it was configured to enter psm.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When scan completes, and we are not associated, we should start
the dev role and ROC. however, we might already be in this situation
(e.g. if we got disconnected during scan). check for it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When setting the WL1271_SCAN_OPT_PRIORITY_HIGH flag, the
driver requests a scan *now*, and the fw doesn't enter psm
before scanning, which in turn might cause packets loss.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Allow enabling/disabling beacon_filtering by debugfs,
in order to reduce the log size while debugging (beacon
filtering is disabled by default in AP mode, as beacons
are needed for ERP configuration).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Crashing on recovery is useful for debugging, as a JTAG
can be connected in order to investigate the current fw state.
(otherwise, a reconfiguration will occur)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Make it easier to match the driver log against
a sniffer log.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add id param to the acx debug print (on wl1271_cmd_configure)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Commit c302b2c959 ("wl12xx: Use a single
fw for both STA and AP roles") changed the name of the firmware name
definition, breaking the build of wl12xx/sdio_test.c.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we are scanning for the wildcard SSID in a scheduled scan, we
should use SCAN_SSID_TYPE_PUBLIC so that we don't filter out the scan
results.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx firmwares support multiple SSIDs in a single sched_scan
run. This patch implements support for it.
We use three different types os sched_scan: FILTER_ANY (ie. not
filtering, only wildcard SSID in the probe_reqs); FILTER_LIST (ie. send out
probe_reqs with the specified SSIDs and only report if they are
found); and FILTER_DISABLED (ie. send out probe_reqs with the
specified SSIDs, but report anything found).
Since we still don't have proper filter support in nl80211/cfg80211
yet, we cannot use filters when the wildcard SSID is used. Thus, we
will not filter anything if the wildcard SSID is specified.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The station didn't get into psm after recovery, because
psm was configured before sta role was started.
Move wl1271_ps_set_mode() to be executed only after
the role was started.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In congested env, sometimes 5 psm entry retries are not enough.
Increase the retries count to 8.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In some corner cases, (invalid) 11g rates were used while
working on 11a band.
Take care of it by initializing rate_set according to the
configured band.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
There was a check preventing 127x devices from using the 11a band when
operating as AP. Since we now support this functionality, remove the
check.
With this patch, a 11a AP starts ok on 127x cards.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add tx_spare_blocks member to the wl1271 struct
for more generic configuration of the amount
of spare TX blocks that should be used.
The default value is 1.
In case GEM cipher is used by the STA, we need
2 spare TX blocks instead of just 1.
Signed-off-by: Guy Eilam <guy@wizery.com>
Acked-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
After commit 5a865ba, we require a separate value to indicate the
number of supported SSIDs in scheduled scans. This patch adds a
proper value to the wl12xx driver.
This fixes a regression in 3.1-rc3 where scheduled scans were not
working properly with the wl12xx driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1271_sdio_power_on checks if the return value of pm_runtime_get_sync
is non-zero, and if so bails out.
However, pm_runtime_get_sync can return a positive number which does not
suggest an error has occurred. This is problematic for two reasons:
1. The function will needlessly bail out without decrementing back the
runtime PM reference counter.
2. wl1271_power_on only checks if wl1271_power_on return value is
negative. This means that wl1271_power_on will continue even if
wl1271_sdio_power_on bailed out. As a result, sdio transactions will
be initiated without properly enabling the sdio function and claiming
the host. This could even lead to a kernel panic.
Fix this by only checking that the return value of pm_runtime_get_sync
is non-negative.
Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The testmode NVS push command is no longer in use. In addition, it has
several implementation issues that prevent it from working correctly:
1. wl1271_tm_cmd_configure relies on wl->chip.id being set. However,
since the device was not necessarily booted by the time the function
is called, wl->chip.id will be initialized to 0.
2. The NVS file is fetched by calling request_firmware() before it is
possible to push an NVS file.
3. The maximum allowed size of nl binary payloads is not sufficient for
pushing NVS files.
4. Pushing 128x NVS files will always fail due to a bug in the
validation code.
5. In case the pushed NVS file is found invalid, the mutex will be kept
locked and the nvs member will become a dangling pointer.
Since this feature is not being used, remove it completely instead of
fixing it.
Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only increment the queue count after actually queuing the skb. This
avoids a spurious increment is case of dropped packets.
Also move the Tx-watermark checking code after the packet is enqueued.
This makes the count more accurate - it includes the just-queued
packet.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Don't pollute the queues with Tx directed to invalid stations. This
can happen during recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This fix eliminates a potential race between starting the AP role
and setting encryption keys.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This adjusts FW TX block allocation for connected stations in PS.
Firmware congestion is measured in allocated packets instead of blocks.
Allow a link in PS to queue up to 2 packets to the FW.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Sometimes the fw doesn't send the DISCONNECT_EVENT_COMPLETE_ID
on station role stop, so don't wait for it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When the FW Tx released blocks counter wraps around, we should correct
our calculation of released blocks. Otherwise we add a large negative
figure to our driver freed blocks counter
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When selecting packets for transmission, prefer the ACs that are least
occupied in the FW. When packets for multiple ACs are present in the FW,
it decides which to transmit according to WMM QoS parameters.
With these changes, lower priority ACs should not be starved when higher
priority traffic is present.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Track the number of freed packets in each AC when receiving an interrupt
from the FW. This paves the way for tracking allocated packets per AC.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When wep key was removed after disconnection, sta_hlid was invalid,
and it resulted in a fw crash.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
when the key was recorded, wl->ap_bcast_hlid was invalid
(since the role wasn't started), so when configuring the
key we need to use the current ap_bcast_hlid.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Unconditionally configure HT rate support to the FW on all ACs
when starting the AP.
When 11n support is disabled by usermode (hostapd), each STA joining
the AP will appear as a non-HT STA. This will stop us from accidentally
transmitting using MCS rates.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When a new STA joins the BSS, configure the HT rates it supports to the
FW.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In addition, set global HT operation mode via ACX_HT_BSS_OPERATION when
a change is detected by usermode
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Start IBSS role when the interface type is IBSS.
As with sta role, use the dev role until the role
is started.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add wl12xx_cmd_role_start_ibss() implementation and defintion.
This function is used in order to start the IBSS role.
Stopping the IBSS is done by using the same api as stop STA,
so there is no need for a separate function.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If hlid was already removed, there is no need to remove
its key (it might cause a fw crash, as the key is invalid).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
After adding a station, call wl12xx_cmd_set_peer_state().
This is required for 11n support.
Change wl12xx_cmd_set_peer_state() prototype to get hlid
as param.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Incorporate interface changes for HT support.
Add ba_bitmap field to the wl1271_link struct, to indicate
activate RX BA sessions (for AP mode).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Using hlid=0 in AP mode is a bug. Dynamically allocate HLIDs.
Set the "first sta hlid" as 3. This will have to be changed
when multiple vifs will be supported.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The BT coex params api have been changed.
Update it, and init coex for both sta and ap.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The ROC command asks the fw stay on the channel of the given
hlid. it currently has 2 primary functions:
1. Allow tx/rx from the device role.
In order to tx/rx packets while the stations is not associated
(e.g. auth req/resp), the device role has to be used, along
with ROC on its link.
Keep the logic similiar to the one used in dummy_join. However,
since we can't scan while we ROC, we add CROC before starting
a scan, and ROC again (if needed) on scan complete.
2. Keeping the antenna for a specific link.
We ROC until the connection was completed (after EAPOLs exchange)
in order to prevent BT coex operations from taking the antenna
and failing the connection (after this stage, psm can be used).
During association, we ROC on the station role, and then CROC
the device role, thus assuring being ROC during all the connection
process.
Delete the WL1271_FLAG_JOINED flag, and use a roc bitmap
to indicate what roles are currently ROCed.
Add wl12xx_roc/croc functions in order to wrap the roc/croc
commands while taking care of the roc bitmap.
The current ROC/CROC state-machine is a bit complicated. In
the future we'll probably want to use wpa_supplicant to control
the ROC during connection.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Allow handling of DUMMY_PACKET_EVENT_ID also in ap mode.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add structs and functions to support the ROC/CROC commands.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
system_hlid is a const hlid (always 0), used by the fw and driver
for packets which are not bound to specific role (e.g. dynamic
memory packets).
indicate it as always allocated.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use ACX_BEACON_FILTER_OPT for both station and ap roles
(use the generic wl1271_acx_beacon_filter_opt()
instead of wl1271_acx_set_ap_beacon_filter() ).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The max template size was increased in the new fw.
However, we should use the max size only when needed, as it
consumes some of the chip's memory.
Thus, by default initialize the templates to the default size.
Initialize to the maximum size only when required.
Use WL1271_CMD_TEMPL_DFLT_SIZE instead of some of the
predefined structs, as some of them didn't account
for additional IEs that might be added to the template.
Delete structs defintions not used after these changes.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Update the rx/tx descriptors according to the new fw api
(fw >= 6/7.3.0.0.75)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Update the scan command to use the new fw api
(fw 6/7.3.0.0.75).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The device role is a special role used for rx and tx frames
prior to association (as the STA role can get packets only
from its associated bssid)
Since this role is required for the sta association process,
we enable it when a new sta interface is created.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
According to the new multi-role flow, we have to enable the
role before using (starting) it, and disable it on cleanup
(after it's no longer needed).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Change the commands and events according to the new fw api
(fw >= 6/7.3.0.0.75).
The main change is the replacement of JOIN/DISCONNECT commands,
with ROLE_START/ROLE_STOP commands.
The use of these commands should be preceded by the ROLE_ENABLE
command (allocating role resources), and followed by the
ROLE_DISABLE command (freeing role resources).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Update the acx commands according to the new fw api
(fw >= 6/7.3.0.0.75).
The main change in most of the ACXs is the addition
of a new role_id/link_id field, which is required
for multi-role operation.
Currently, we don't really support multi-role, as
most of our data (inside wl) is global.
As the current fw doesn't support concurrent roles
yet, keep it this way and add wl->role_id and
wl->sta_hlid to save the active role/link.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Update the fw status struct according to the new fw api
(fw >= 6/7.0.0.35).
All the roles use the same struct now.
The memory accounting was changed a bit according to
the struct changes.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The new fw doesn't support rx_filtering configuration (as a
stand-alone command. the rx filtering is done automatically
according to the active role).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In order to keep to driver compiling during the patchset,
while avoiding one-huge-patch, temporarily disable some
advanced ap functions.
These changes will be reverted later in the patchset, as
part of the patches for advanced ap functions support.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This does not make sense in fw >= 6/7.3.0.0.75 (wl127x/wl128x) -
we don't use Tx blocks to measure FW occupancy anymore.
This reverts commit 9e374a37b6.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In each case, the freed data should be freed in the error handling code
as
well.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the value of PG version for 128x at sysfs, remove write permissions
from PG version (hw_pg_ver) in sysfs and add remove files
(hw_pg_ver,bt_coex_state) from sysfs while freeing hardware.
New macro names for register Fuse_data_2_1 depend on architecture.
Propagate chip id through wiphy in PLT mode which still not work of
a bug in ethtool.
Signed-off-by: Gery Kahn <geryk@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In case of QoS packets the packet payload isn't aligned to
4 bytes. In that case the mac80211 layer take care of that
via memmove() in ieee80211_deliver_skb().
Add support of copy packets from aggregation buffer to the
skbs with packet payload aligned care. In case of QoS packets
copy the packets in offset of 2 bytes guarantee payload aligned
to 4 bytes.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This driver uses IW_ESSID_MAX_SIZE when it should
be using IEEE80211_MAX_SSID_LEN instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split tx_queue_count to count per-AC skb's queued, instead of relying on
the skb-queue len. The skb queues used were only valid in STA-mode, as
AP-mode uses per-link queues.
This fixes a major regression in AP-mode, caused by the patch
"wl12xx: implement Tx watermarks per AC". With that patch applied, we
effectively had no regulation of Tx queues in AP-mode. Therefore a
sustained high rate of Tx could cause exhaustion of the skb memory pool.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Sometimes we only get the Tx power level via op->config when the FW is
off. Record the received power level when this happens and use it to
initialize the firmware during boot.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Set the maximum FW supported power levels for 11a channels.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Configure the device (to wowlan) only if the sta/ap
is associated/started.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Skip manual device power on in case runtime PM is enabled for
our device.
This eliminates a secondary & redundant SDIO init sequence.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Each AC is stopped when its queue is filled up to the high watermark,
and restarted when its queue it lower than the low watermark. This
ensures congested ACs are not able to starve other ACs.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The current TX watermark settings cause the driver to stop queues too
frequently. Among other things, this can have a negative impact on WMM
prioritization, since mac80211 sorts pending packets by their ACs.
Fix this by increasing the high watermark to 256 packets. Increase the
low watermark to 32 to minimize periods with queues being stopped.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When selecting packets for transmission, prefer the ACs that are least
occupied in the FW. When packets for multiple ACs are present in the FW,
it decides which to transmit according to WMM QoS parameters.
With these changes, lower priority ACs should not be starved when higher
priority traffic is present.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When operating with TKIP encryption, the function wl1271_tx_fill_hdr()
relocates the 802.11 header to the start of the frame, and leaves room
for the security header.
Some functions in the Tx path rely on the location of the header,
namely, for purposes of roaming in STA mode and connecting new stations
in AP mode. Call these functions only after the header is relocated.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In AP mode we register for the MAX_TX_RETRY and INACTIVE_STA events.
Both are reported to the upper layers as a TX failure in the offending
stations.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Do not reset the security sequence number when issuing a join command or
interface is removed. Instead, reset the counter only during the unjoin
command.
Added the notion of counter wrap-around to the LSB number in
wl1271_tx_complete_packet.
Added post recovery padding to adjust for potential security number
progress during the recovery process by the firmware and avoid
potential interop issues in encrypted networks.
Signed-off-by: Oz Krakowski <ozk@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When adding a station, use the information given in the mac80211
populated ieee80211_sta structure to determine if it supports WME.
Provide this information to the FW.
This patch depends on "mac80211: propagate information about
STA WME support down".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A recently added feature to the firmware enables the driver to retrieve
firmware logs via the host bus (SDIO or SPI).
There are two modes of operation:
1. On-demand: The FW collects its log in an internal ring buffer. This
buffer can later be read, for example, upon recovery.
2. Continuous: The FW pushes the FW logs as special packets in the RX
path.
Reading the internal ring buffer does not involve the FW. Thus, as long
as the HW is not in ELP, it should be possible to read the logs, even if
the FW crashes.
A sysfs binary file named "fwlog" was added to support this feature,
letting a monitor process read the FW messages. The log is transferred
from the FW only when available, so the reading process might block.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
During recovery work commands sent to the FW could fail and schedule
additional recovery work. Since the chip is going to be powered off,
avoid recursive recoveries.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The FW initialization might depend on the FW revision, so check for any
FW quirks right after booting it.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When resuming (after wowlan), we want the rx packets (which is
usually the wake-up packet itself) to be passed to mac80211 only
after the resume notifier was completed, and mac80211 is up and
running (otherwise, the packets will be dropped).
By enqueueing the netstack_work to a freezable workqueue, we can
guarantee the rx processing to occur only after mac80211 was resumed.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl1271_flush_deferred_work(), which calls ieee80211_rx() and
ieee80211_tx_status(), is called from a process context.
hence, use ieee80211_tx_status_ni() instead of ieee80211_tx_status().
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When resuming while connected (without wowlan), the interface
is already IF_OPER_UP, so we won't get the notifier callback,
and hence never complete the association (from wl12xx perspective)
This situation, among other potential problems, prevents the
station from entering psm.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some platforms don't support the wake_irq, so disable wowlan
in this case, and avoid the "Unbalanced IRQ wake disable"
warning on disable_irq_wake().
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Beacon filtering needs to be enabled so AP won't wake up by
by every received beacon.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We set wl->wow_enabled on every suspend(), so we need to clear it
on every resume().
(we can't rely on setting wl->wow_enabled=false in suspend(),
as it being called only when wowlan triggers are configured)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Since mac80211 calls suspend/resume only when wowlan triggers
exist, there is no need to check for triggers existance in the
callbacks as well.
Add a WARN_ON() to verify it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The Low Power DRPw (LPD) mode contains several optimizations
that designed to reduce power consumption. The purpose
is to save current consumption in RX and Listen mode.
LPD setting apply only for wl127x AP mode (not wl128x)
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If our SDIO function has its runtime PM disabled, don't try to
manipulate its runtime PM status at all. This way we can still
power on cards plugged to mmc hosts that are not MMC_CAP_POWER_OFF_CARD.
Reported-and-tested-by: Tim Yamin <tim@kangatronix.co.uk>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The firmware, in practice, treats the channels in three separate
blocks, one for each band (bg, a and j). Instead of using a single
array and doing some magic with indices, split the array in 3 to make
it more readable.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Due to rebase error, the patch for commit cb5ae0 ("wl12xx: configure
rates when working in ibss mode") was wrong - a blob was added
into the wrong function. fix it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
crc7 is used only in wl12xx_spi.
Remove redundant crc7.h includes, and update Kconfig to select CRC7
only if WL12XX_SPI is being selected.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Beacon early termination doesn't help much in the 5GHz band and masks
channel switch IE Beacons. Thus, change the code to use BET only in
2.4GHz.
[Reworded the commit log slightly -- Luca.]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Allow control over rx_streaming interval and operation mode
(always/only on coex) via debugfs.
e.g.
echo 100 > /debug/ieee80211/phy0/wl12xx/rx_streaming/interval
echo 1 > /debug/ieee80211/phy0/wl12xx/rx_streaming/always
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When rx_streaming.interval is non-zero, use automatic rx streaming.
Enable rx streaming on the each rx/tx packet, and disable it
rx_streaming.duration msecs later.
When rx_streaming.always=0 (default), rx streaming is enabled only
when there is a coex operation.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl12xx supports the "rx streaming" feature:
When in ps mode, and @timeout msecs have been passed since
the last rx/tx, it issues trigger packets (QoS-null/PS-Poll packets,
according to the ac type) in const intervals (in order to reduce
the rx time).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Those have little value. Remove those to
make the driver less noisy.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Nops aren't needed. When we actually need
those calls, then we add them with meat
and barbecue sauce.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
->init and ->reset are optional - at least
sdio.c doesn't implement them - so allow those
pointers to be NULL.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Those have little value. Remove those to make
the driver less noisy.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
That's only needed during init anyway, let's free
some space after we're done probing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Adding new event that close RX BA session in case of periodic BT activity
limiting WLAN activity.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel oops when trying to use passive scheduled scans. The
reason was that in passive scans there are no SSIDs, so there was a
NULL pointer dereference.
To solve the problem, we now check the number of SSIDs provided in the
sched_scan request and only access the list if there's one or more
(ie. passive scan is not forced). We also force all the channels to
be passive by adding the IEEE80211_CHAN_PASSIVE_SCAN flag locally
before the checks in the wl1271_scan_get_sched_scan_channels()
function.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a different value for DFS dwell time when performing a scheduled
scan. Previously we were using the same value as for normal passive
scans. This adds some flexibility between these two different types
of passive scan.
For now we use 150 TUs for DFS channel dwell time. This may need to
be fine-tuned in the future.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DFS channels were never getting included in the scheduled scans,
because they always contain the passive flag as well and the call was
asking for DFS and active channels.
Fix this by ignoring the passive flag when collecting DFS channels.
Also, move the DFS channels in the channel list before the 5GHz active
channels (this was implemented in the FW differently than specified).
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were comparing bitwise AND results with a boolean, so when the
boolean was set to true, it was not matching as it should.
Fix this by booleanizing the bitwise AND results with !!.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a compilation error when PM is not enabled:
CC [M] drivers/net/wireless/wl12xx/main.o
drivers/net/wireless/wl12xx/main.c:3653: error: unknown field 'suspend' specified in initializer
drivers/net/wireless/wl12xx/main.c:3653: warning: initialization from incompatible pointer type
drivers/net/wireless/wl12xx/main.c:3654: error: unknown field 'resume' specified in initializer
drivers/net/wireless/wl12xx/main.c:3654: warning: initialization from incompatible pointer type
Fix this by adding #ifdef's in the appropriate places.
Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When operating as station, enter psm before suspending
the device into wowlan state.
Add a new completion event to signal when psm was entered
successfully.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Since wowlan requires the ability to stay awake while the host
is suspended, declare support for NL80211_WOW_TRIGGER_ANYTHING
if the MMC_PM_KEEP_POWER capability is being supported.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When WoW is enabled, the interface will stay up and the chip will
be powered on, so we have to flush/cancel any remaining work, and
prevent the irq handler from scheduling a new work until the system
is resumed.
Add 2 new flags:
* WL1271_FLAG_SUSPENDED - the system is (about to be) suspended.
* WL1271_FLAG_PENDING_WORK - there is a pending irq work which
should be scheduled when the system is being resumed.
In order to wake-up the system while getting an irq, we initialize
the device as wakeup device, and calling pm_wakeup_event() upon
getting the interrupt (while the system is about to be suspended)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
if a wow trigger was configured, set the MMC_PM_KEEP_POWER flag
on suspend, so our power will be kept while the system is suspended.
We needed to set this flag on each suspend attempt (when we want
to keep power)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Additionally, add wow_enabled field to wl, to indicate
whether wowlan was configured.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
set the sdio interrupt as wake_up interrupt, so we will be able
to wake up the suspended system (Wake-On-Wireless)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The current firmware only supports scheduled scan in station mode and
when idle. To prevent the firmware from crashing, return -EOPNOTSUPP
when sched_scan start is called in an invalid state.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Subscribe and listen to PERIODIC_SCAN_REPORT_EVENT_ID and
PERIODIC_SCAN_COMPLETE_EVENT_ID in preparation for the scheduled scan
implementation.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Set the spectrum management bit in the hw flags so that mac80211 will
set the WLAN_CAPABILITY_SPECTRUM_MGMT bit in association requests
(which in practice means that we support 802.11h spectrum management).
[Reworded the commit log -- Luca.]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This patch adds a beacon filter rule to pass up the beacons that
contain changed HT information elements. These beacons need to be
passed to mac80211 so that it can act on such changes.
[Reworded commit log -- Luca.]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Simplify wl1271_ssid_set by re-using cfg80211_find_ie instead of
reimplementing it.
Additionally, add a length check to prevent a potential buffer overflow.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
By reading the "driver_state" debugfs value we get all the important
state information from the wl12xx driver. This helps testing and
debugging, particularly in situations where the driver seems "stuck".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When operating as AP, the TX queues are not stopped when we start
recovery. mac80211 is notified only after the fact. When there is
pending TX, it will be queued even after the FW is down. This leads to
situations where the TX queues are stopped (because of the TX-watermark
mechanism), and are never woken up when we return from recovery.
Fix this by explicitly stopping the TX queues when before initiating
recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This entry is useful for debugging the driver state machine during
recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When there's a change in the basic rates of the AP, reconfigure relevant
templates with the new rates.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the minimal rate configured in the basic rates set as the AP
broadcast and multicast rate. The minimal rate is used to ensure weak
links can still communicate.
When the basic rates contains at least one OFDM rate, configure all
unicast TX rates to OFDM only.
Unify rate configuration on initialization and on change notification
into a single function.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When performing recovery, print the firmware version and program
counter (by reading the SCR_PAD4 register). The value of the firmware
program counter during assert can be useful for debugging.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We use a long timeout (2 seconds) when sending commands to the FW.
When a command times out, it means the FW is stuck, and we should
commence recovery.
This should make recovery times shorter as we'll recover on the first
timeout indication.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New AP-mode FWs filter external beacons by default. Disable this
filtering on start up so we can properly configure ERP protection.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the wiphy RTS and fragmentation thresholds for initializing the FW
when possible. This mitigates a bug where previously set values are
forgotten after interface down/up.
Add checks before settings these values to ensure they are valid. Use
default values when invalid thresholds are configured.
Update the default RTS threshold to the maximum value given by the
specification.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize AP specific BT coexitance parameters to default values and
enable them in AP mode.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
It is preferred to use the setter that to set queue_mapping directly.
This also helps backporting in compat-wireless.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When packets arrive with a RX descriptor indicating corruption, discard
them.
In general white-list the RX descriptor status to prevent rouge data
from being sent up.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Frames are considered pending when they reside in the driver TX queue or
already queued in the FW.
This notion of "pending" is appropriate for power save considerations in
STA mode, but not necessarily in other modes (for instance P2P-GO).
[Fixed a sparse warning about missing "static" in a function
declaration -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The FW can dynamically manage its internal TX & RX memory pools, moving
blocks from one pool to another when necessary. This can significantly
improve performance. Currently this feature is enabled only for 128x.
Enable dynamic memory for 127x as well. Other parameters in the memory
configuration structure may need to be fine tuned, as the optimal values
for these may change once dynamic memory is enabled.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The driver stops sending TX packets when either there aren't enough
memory blocks, or it runs out of TX descriptors. The driver continues to
send packets to the FW only when more memory blocks are available.
The FW might free TX descriptors without freeing the corresponding
memory blocks, especially when dynamic memory is enabled. In cases where
memory blocks are not freed at all, the driver will keep waiting for
more memory blocks indefinitely.
Fix this by clearing the WL1271_FLAG_FW_TX_BUSY flag when there are
available TX descriptors.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The 128x/AP firmware does not yet support dynamic memory. Temporarily,
the memory configuration for the 127x was used both for 127x/AP as well
as 128x/AP. Since the two chips don't have the same number of memory
blocks, TP was significantly degraded.
This hasn't been fine tuned yet, but using the base 128x numbers
(without dynamic memory) seems to yield much better results (around 30%
more). Additional fine tuning will be required in the future.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When configuring ACX_WAKE_UP_CONDITIONS (before entering psm), we
tell the firmware to wake up once in N DTIMs/beacons.
Allow control of this value via debugfs (for debugging purposes).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reducing the retries of sending PS exit packets to the peer AP.
That fix is to avoid sending unrealizable number of PS exit packets
in case of ap lost.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add support to FM WLAN coexistence (STA only). Some WiFi harmonics
may interfere with FM operation, to avoid this problem special
coexistence techniques are activated around some FM frequencies.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When working in ibss mode, we don't configure rate policy per station
(as we use the same link for multiple stations), so currently the
1mb/s rate is being used.
Instead, configure the firmware to use the whole 11b rates by default.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
ieee80211_reconfig() sets most of the "changed" flags regardless
of the actual change (e.g. BSS_CHANGED_ASSOC will be set even if
the interface is still not associated). in this case the driver
will issue some unneeded commands.
Since the driver relies solely on the BSS_CHANGED_ASSOC flag,
without checking if there was an actual change, it will end up
issuing unjoin() and dummy_join() commands, although it was
never associated and should just remain idle.
Avoid it by checking the actual state change, in addition to the
"changed" flag.
(there seem to be more redundant configuration commands being
issued, but they shouldn't harm)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When debugging, reduce the padding size from each rx packet, to
get the actual packet size (so comparing it against a cap file
will be easier)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Fix mismatch between the REF CLK and TCXO CLK information that is
set in the platform data and the NVS, so we override what comes
from the NVS and replace it with what comes from the platform data.
[Small fix in a comment -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The elp_work is being enqueued on wl1271_ps_elp_sleep, but doesn't get
cancelled on wl1271_ps_elp_wakeup. This might cause immediate entrance
to elp when the wl->mutex is being released, rather than using the delayed
enqueueing optimization.
Cancel elp_work on wakeup request, and add a new WL1271_FLAG_ELP_REQUESTED
flag to further synchronize the elp actions.
[Fixed a couple of typos in some comments -- Luca]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
commit d05c806 ("wl12xx: rearrange some ELP wake_up/sleep calls")
introduced a bug in which wl1271_ps_elp_wakeup() was called instead
of wl1271_ps_elp_sleep() after completing the tx work.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
End-of-transaction flag should be set when working with
wl127x chip on AP mode.
Thanks Ido Yariv <ido@wizery.com> for the guidance with that.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In AP mode we register for the MAX_TX_RETRY and INACTIVE_STA events.
Both are reported to the upper layers as a TX failure in the offending
stations.
In STA mode we register only for the MAX_TX_RETRY event. A TX failure is
interpreted as a loss of connection.
Support for IEEE80211_HW_REPORTS_TX_ACK_STATUS has been removed to avoid
the inherent race condition of a mac80211 TX failure counter in addition
to the FW counter.
This patch depends on "mac80211: allow low level driver to report packet
loss"
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix sparse warning:
CHECK drivers/net/wireless/wl12xx/main.c
drivers/net/wireless/wl12xx/main.c:1246:17: warning: symbol 'wl12xx_alloc_dummy_packet' was not declared. Should it be static?
Signed-off-by: Luciano Coelho <coelho@ti.com>
Instead of hardcoding the hci_io_ds configuration that we write to the
SDIO_IO_DS top registed, read it from the default configuration so
that it's easier to change for different platforms.
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some platforms are incapable of triggering on level interrupts. Add a
platform quirks member in the platform data structure, as well as an
edge interrupt quirk which can be set on such platforms.
When the interrupt is requested with IRQF_TRIGGER_RISING, IRQF_ONESHOT
cannot be used, as we might miss interrupts that occur after the FW
status is cleared and before the threaded interrupt handler exits.
Moreover, when IRQF_ONESHOT is not set, iterating more than once in the
threaded interrupt handler introduces a few race conditions between this
handler and the hardirq handler. Currently this is worked around by
limiting the loop to one iteration only. This workaround has an impact
on performance. To remove to this restriction, the race conditions will
need to be addressed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The total number of TX memory blocks may change when the dynamic memory
option is enabled. The current implementation only tracks the available
memory blocks, which over-complicates TX blocks accounting.
By tracking the number of allocated blocks, calculation of the number of
available blocks becomes simpler and cleaner. It simply equals the total
number of TX memory blocks minus the allocated ones.
Also, remove some unnecessary castings and use union member accesses
instead.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The current implementation allocates a skb each time one is requested by
the firmware. Since dummy packets are handled differently than regular
packets, the skb needs to be marked. Currently, this is done by
setting the pkt_type member to 5. This might not be safe, as we cannot
be sure that there won't be any other packets with this pkt_type value.
Since the packet does not change from one request to another, we can
simply allocate a dummy packet template and always send it. All changes
to the skb done during packet preparation must be reverted, so the same
skb can be reused.
The dummy packets are not transmitted, therefore there's no need to set
the BSSID or our own MAC address.
In addition, the header portion of the packet was zeroed by mistake, so
fix that as well.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Simplify and clean up the block size alignment code:
1. Set the block size according to the padding field type, as it cannot
exceed the maximum value this field can hold.
2. Move the alignment code into a function instead of duplicating it in
multiple places.
3. In the current implementation, the block_size member can be
misleading because a zero value actually means that there's no need to
align. Declare a block size alignment quirk instead.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Clean up the boot sequence code & fix the following issues:
1. Always read the registers' values and set the relevant bits instead of
zeroing all other bits
2. Handle cases where wl1271_top_reg_read returns an error
3. Verify that the HW can detect the selected clock source
4. Remove 128x PG10 initialization code
5. Configure the MCS PLL to work in HP mode
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Issuing multiple JOIN commands to the wl12xx's firmware, while
we're associated, might have undesired implications, so the driver
prints a message when that happens, and warn developers who check
out the source.
Update the commentary in order to consider the one valid scenario
where this can happen: roaming.
Cautiously keep the message for now, until we either gain confidence
there are no unintentional JOIN-while-associated events, or until
we move to the new multi-role fw who solves this multiple-join issue
for good.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx device normally drops all frames coming from BSSID
it is not joined with.
This behavior is configured today by the wl12xx driver in response
to a handful of ieee80211_bss_change and ieee80211_conf_changed
notification flags, such as BSS_CHANGED_ASSOC, BSS_CHANGED_BSSID,
IEEE80211_CONF_CHANGE_IDLE, etc..
This breaks when we roam to a new BSSID, where authentication frames
are sent before any BSS_CHANGED/CONF_CHANGED flags are received.
When this happens the hardware silently drops the authentication
responses, and the roaming fails.
Ideally this aggressive filtering behavior of the device should be disabled
upon a notification from mac80211. Such notification will take place
after multi-channel support will be added: mac80211 will likely send a
remain-on-channel notification to drivers when entering sensitive
states (like authentication), otherwise the firmware might jump to
different channels (to serve a different role).
Until those notifications materialize, disable the hw BSSID filter
when authentication requests are sent, so roaming would work.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Because of the hardware recovery mechanism, its possible the
__wl1271_op_remove_interface is called twice. Currently, this leads to a
kernel crash even before a kernel WARNing can be issued.
Fix this.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
ELP (Extremely/Enhanced Low Power, or something like that ;)) refers to
the powerstate of the 12xx chip, in which very low power is consumed,
and no commands (from the host) can be issued until the chip is woken up.
Wakeup/sleep commands must be protected by a wl->mutex, so it's generally
a good idea to call wakeup/sleep along with the mutex lock/unlock (where
needed). However, in some places the wl12xx driver calls wakeup/sleep in
some "inner" functions. This result in some "nested" wakeup/sleep calls
which might end up letting the chip go to sleep prematurely (e.g. during
event handling).
Fix it by rearranging the elp calls to come along with mutex_lock/unlock.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize the channel and band from mac80211 conf even when the FW is
not yet loaded. This mitigates a bug in AP-mode where the channel was
never changed from its initial setting after FW boot and was therefore
never configured to FW.
Reported-by: Alexander Boukaty <alexanderb@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We were using an array of booleans to mark the channels we had already
scanned. This was causing a sparse error, because bool is not a type
with defined size. To fix this, use bitmasks instead, which is much
cleaner anyway.
Thanks Johannes Berg for the idea.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Fix the following sparse warnings:
drivers/net/wireless/wl12xx/main.c:1129:5: warning: symbol '__wl1271_plt_stop' was not declared. Should it be static?
drivers/net/wireless/wl12xx/main.c:2988:5: warning: symbol 'wl1271_op_ampdu_action' was not declared. Should it be static?
Both functions should be static.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The Soft Gemini BT load ratio value has changed its meaning with FW
version 6.1.0.0.310. It now means the passive scan compensation
percentage during A2DP EDR. Instead of 50, we need to use 200.
Fix the SG configuration accordingly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The firmware requires dummy packets to be sent using TID 7
(WL1271_TID_MGMT). Instead of hardcoding it in the tx_fill_hdr()
function, set it when creating the packet itself.
This requires Eliad's fix to set the actual TID in the TX descriptor.
Cc: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When passing a tx frame, the driver incorrectly set desc->tid
with the ac instead of the actual tid.
It has some serious implications when using 802.11n + QoS,
as the fw starts a BlockAck with the wrong tid (which finally
cause beacon loss and disconnection / some fw crash)
Fix it by using the actual tid stored in skb->priority.
Reported-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The interface list maintained in main.c is not mutex protected. This could
cause issues, as the list is accessed from notifier chains.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On wl128x based devices, when TX packets are aggregated, each packet
size must be aligned to the SDIO block size, and sent using block mode
transfers.
The block size is set to 256 bytes, which is less than the maximum
possible byte transfer. Thus, if two small packets (< 256 bytes) are
aggregated, the aggregation buffer size would be 512, and will be sent
using byte mode transfers. This can have undesired side effects.
Fix this by setting the MMC_QUIRK_BLKSZ_FOR_BYTE_MODE mmc card quirk.
For 127x chips this has no effect, as the block size is set to 512
bytes.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Allow early termination of 50 consecutive beacons.
This value is the recommended one by the 12xx's system/RF team,
and tests show that power consumption is improved as expected.
Reported-by: Ruthy Zaphir <ruthyz@ti.com>
Tested-by: Danil Shalumov <danils@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx chip supports one Rx STBC spatial stream. Announce this in
the HT capabilities info field.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The rx-status passed to mac80211 along with each received frame contains the
band on which the frame was received. Under certain circumstances, this band
information may be incorrect, causing in worst case a WARNING from mac80211,
and causes the received frame to be dropped.
This scenario mainly occurs when performing connected-mode scans, when the
received scan results are from the other band than the one currently
associated to.
[Since desc_band doesn't exist anymore, use status->band in the later
call to ieee80211_channel_to_frequency() to fix compilation -- Luca]
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
All the new firmware versions (>=6.1.3.50.58 for STA and >=6.2.0.0.47
for AP) use 1 spare TX block. We still want to support older
firmwares that require 2 spare blocks, so added a quirk to handle the
difference.
Also implemented a generic way of setting quirks that depend on the
firmware revision.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add support to wl128x chip via chip id
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Choose a different FW for AP-mode wl127x and wl128x chips, base on chip
ID at boot time.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Support sending dummy packet to wl128x FW as results of
dummy packet event. That is part of dynamic TX mem blocks mechanism.
Only send dummy packet when not in AP mode.
[Even though the DUMMY_PACKET_EVENT_ID and the
STA_REMOVE_COMPLETE_EVENT_ID events are defined to the same value, we
need to treat them separately in the code. Keep the check and enable
STA_REMOVE_COMPLETE_EVENT_ID for AP mode and DUMMY_PACKET_EVENT_ID for
STA. Moved one warning to a cleaner place. Use WL1271_TID_MGMT for
dummy packets -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reduced bus transactions in the Tx & Rx path.
[Removed unnecessary check wl->chip.id != CHIP_ID_1283_PG20 when
checking the quirk -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Separate the memory configuration to chip-specific structures and
implement dynamic memory for wl128x.
This feature allows us to move TX memory blocks to the RX pool when
the RX path is overloaded.
Thanks for Arik Nemtsov <arik@wizery.com> for helping simplify the
wl1271_fw_status() code.
[Rewrote the commit subject and message for clarity; improved some
comments and changed "spare" to "padding" for consistency; added a
FIXME for the AP memory configuration -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Boot sequence support FREF clock and TCXO clock.
WL128x has two clocks input - TCXO and FREF.
TCXO is the main clock of the device, while FREF is used to sync
between the GPS and the cellular modem.
Auto-detection checks where TCXO is 32.736MHz or 16.368MHz, in that
case the FREF will be used as the WLAN/BT main clock.
[Use clock enumeration as defined in linux/wl12xx.h; remove
unnecessary else block in wl128x_switch_fref; remove unnecessary
change in main.c; remove some unnecessary debug prints and comments;
fix potential use of uninitialized value (pll_config) -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Take care of FW & NVS with the auto-detection between wl127x and
wl128x.
[Moved some common code outside if statements and added notes about
NVS structure assumptions; Fixed a bug when checking the nvs size: if
the size was incorrect, the local nvs variable was set to NULL, it
should be wl->nvs instead. -- Luca]
[Merged with potential buffer overflow fix -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New general and radio parameters structures and functions.
Implemented as separate functions due to auto-detection
between wl127x and wl128x.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add the the set_block_size op in the SDIO and in the SPI modules.
Since it is only used with SDIO, just explicitly set the op to NULL in
spi.c
Signed-off-by: Luciano Coelho <coelho@ti.com>
New acx command that sets: Rx fifo enable reduced bus transactions
in RX path. Tx bus transactions padding to SDIO block size that
improve preference in Tx and essential for working with SDIO HS (48Mhz).
The max SDIO block size is 256 when working with Tx bus transactions
padding to SDIO block.
Add new ops to SDIO & SPI that handles the win size change in case of
transactions padding (relevant only for SDIO).
[Fix endianess issues; simplify sdio-specific block_size handling;
minor changes in comments; use "aligned_len" in one calculation
instead of "pad" to avoid confusion -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Definitions to support wl128x:
- New FW file name
- Chip ID
- New PLL Configuration Algorithm macros that will be used at wl128x
boot stage
- Rename NVS macro name: wl127x and wl128x are using the same NVS
file name. However, the ini parameters between them are
different. The driver will validate the correct NVS size in
wl1271_boot_upload_nvs().
[Cleaned up some of the definitions. -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In order to prevent overran of IRQ polarity via FW the polarity setting move after
FW download and before IRQ enable.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net: Add support for SMSC LAN9530, LAN9730 and LAN89530
mlx4_en: Restoring RX buffer pointer in case of failure
mlx4: Sensing link type at device initialization
ipv4: Fix "Set rt->rt_iif more sanely on output routes."
MAINTAINERS: add entry for Xen network backend
be2net: Fix suspend/resume operation
be2net: Rename some struct members for clarity
pppoe: drop PPPOX_ZOMBIEs in pppoe_flush_dev
dsa/mv88e6131: add support for mv88e6085 switch
ipv6: Enable RFS sk_rxhash tracking for ipv6 sockets (v2)
be2net: Fix a potential crash during shutdown.
bna: Fix for handling firmware heartbeat failure
can: mcp251x: Allow pass IRQ flags through platform data.
smsc911x: fix mac_lock acquision before calling smsc911x_mac_read
iwlwifi: accept EEPROM version 0x423 for iwl6000
rt2x00: fix cancelling uninitialized work
rtlwifi: Fix some warnings/bugs
p54usb: IDs for two new devices
wl12xx: fix potential buffer overflow in testmode nvs push
zd1211rw: reset rx idle timer from tasklet
...
We were allocating the size of the NVS file struct and not checking
whether the length of the buffer passed was correct before copying it
into the allocated memory. This is a security hole because buffer
overflows can occur if the userspace passes a bigger file than what is
expected.
With this patch, we check if the size of the data passed from
userspace matches the size required.
This bug was introduced in 2.6.36.
Cc: stable@kernel.org
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MODULE_AUTHOR() macro in the main module (wl12xx) has been updated
to reflect one of the author's new email address, but the wl12xx_spi
and wl12xx_sdio modules haven't been updated. This patches updates
them.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the gf_protection bit when calling ACX_HT_BSS_OPERATION according
to the GF bit passed by mac80211 in ht_operation_mode.
[Added a proper commit message -- Luca]
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Commands are sometimes sent to FW on scan completion. Make sure the chip
is awake to receive them. Sending commands while the chip is in ELP
can cause SDIO read errors and/or crash the FW.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Tests have shown that the requested number of memory blocks is
sub-optimal. Slightly modify the requested number of memory blocks for
TX.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
TX might be handled in the threaded IRQ handler, in which case, TX work
might be scheduled just to discover it has nothing to do.
Save a few context switches by cancelling redundant TX work in case TX
is about to be handled in the threaded IRQ handler. Also, avoid
scheduling TX work from wl1271_op_tx if not needed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The interrupt of the wl12xx is a level interrupt in nature, since the
interrupt line is not auto-reset. However, since resetting the interrupt
requires bus transactions, this cannot be done from an interrupt
context. Thus, requesting a level interrupt would require to disable the
irq and re-enable it after the HW is acknowledged. Since we now request
a threaded irq, this can also be done by specifying the IRQF_ONESHOT
flag.
Triggering on an edge can be problematic in some platforms, if the
sampling frequency is not sufficient for detecting very frequent
interrupts. In case an interrupt is missed, the driver will hang as the
interrupt line will stay high until it is acknowledged by the driver,
which will never happen.
Fix this by requesting a level triggered interrupt, with the
IRQF_ONESHOT flag.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
To achieve maximal throughput, it is very important to react to
interrupts as soon as possible. Currently the interrupt handler wakes up
a worker for handling interrupts in process context. A cleaner and more
efficient design would be to request a threaded interrupt handler. This
handler's priority is very high, and can do blocking operations such as
SDIO/SPI transactions.
Some work can be deferred, mostly calls to mac80211 APIs
(ieee80211_rx_ni and ieee80211_tx_status). By deferring such work to a
different worker, we can keep the irq handler thread more I/O
responsive. In addition, on multi-core systems the two threads can be
scheduled on different cores, which will improve overall performance.
The use of WL1271_FLAG_IRQ_PENDING & WL1271_FLAG_IRQ_RUNNING was
changed. For simplicity, always query the FW for more pending
interrupts. Since there are relatively long bursts of interrupts, the
extra FW status read overhead is negligible. In addition, this enables
registering the IRQ handler with the ONESHOT option.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The SDIO bus is claimed and released for each SDIO transaction. In
addition to the few CPU cycles it takes to claim and release the bus, it
may also cause undesired side effects such as the MMC host stopping its
internal clocks.
Since only the wl12xx_sdio driver drives this SDIO card, it is safe to
claim the SDIO host once (on power on), and release it only when turning
the power off.
This patch was inspired by Juuso Oikarinen's (juuso.oikarinen@nokia.com)
patch "wl12xx: Change claiming of the (SDIO) bus".
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On newer hardware revisions, there is no need to write the host's
counter at the end of a RX transaction. The same applies to writing the
number of packets at the end of a TX transaction.
It is generally a good idea to avoid unnecessary SDIO/SPI transfers.
Throughput and CPU usage are improved when avoiding these.
Send the host's RX counter and the TX packet count only if needed, based
on the hardware revision.
[Changed WL12XX_QUIRK_END_OF_TRANSACTION to use BIT(0) -- Luca]
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The FW has a limited amount of memory for holding frames. In case it
runs out of memory reserved for RX frames, it'll have no other choice
but to drop packets received from the AP. Thus, it is important to
handle RX data interrupts as soon as possible, before handling anything
else.
In addition, since there are enough TX descriptors to go around, it is
better to first send TX frames, and only then handle TX completions.
Fix this by changing the order of function calls in wl1271_irq_work.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Frames in the tx_frames array include extra private headers, which must
be removed before passing the skbs to ieee80211_tx_status.
Fix this by removing any private headers in wl1271_tx_reset, similar to
how this is done in wl1271_tx_complete_packet.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Runtime PM might not always be enabled. Even if it is enabled in the
running kernel, it can still be temporarily disabled, for instance
during suspend. Runtime PM is opportunistic in nature, and should not be
relied on for toggling power.
In case the interface is removed and re-added while runtime PM is
disabled, the FW will fail to boot, as it is mandatory to toggle power
between boots. For instance, this can happen during suspend in case one
of the devices fails to suspend before the MMC host suspends, but after
mac80211 was suspended. The interface will be removed and reactivated
without toggling the power.
Fix this by calling mmc_power_save_host/mmc_power_restore_host in
wl1271_sdio_power_on/off functions. It will toggle the power to the chip
even if runtime PM is disabled. The runtime PM functions should still be
called to make sure runtime PM does not opportunistically power the chip
off (e.g. after resuming from system suspend).
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In the linux-firmware git tree, the firmwares and the NVS are inside
the ti-connectivity directory. Fix the filenames that the driver
looks for accordingly.
[Fixed commit message and merged with the latest changes. -- Luca]
Signed-off-by: Sebastien Jan <s-jan@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The return value of the tx operation is commonly
misused by drivers, leading to errors. All drivers
will drop frames if they fail to TX the frame, and
they must also properly manage the queues (if they
didn't, mac80211 would already warn).
Removing the ability for drivers to return a BUSY
value also allows significant cleanups of the TX
TX handling code in mac80211.
Note that this also fixes a bug in ath9k_htc, the
old "return -1" there was wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com> [ath5k]
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> [rt2x00]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net> [b43, rtl8187, rtlwifi]
Acked-by: Luciano Coelho <coelho@ti.com> [wl12xx]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the PS mode of each link according to a bitmap polled from
fw_status. Manually notify mac80211 about PS mode changes in connected
stations.
mac80211 will only be notified about PS start when the station is in PS
and there is a small number of TX blocks from this link ready in HW.
This is required for waking up the remote station since the TIM is
updated entirely by FW.
When a station enters mac80211-PS-mode, we drop all the skbs in the
low-level TX queues belonging to this sta with STAT_TX_FILTERED
to keep our queues clean.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Count the number of FW TX blocks allocated per link. We add blocks to a
link counter when allocated for a TX descriptor. We remove blocks
according to counters in fw_status indicating the number of freed blocks
in FW. These counters are polled after each IRQ.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Remove an active hlid when chip wakeup fails. In addition rename the
involved functions.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When operating in AP mode the wl1271 hardware filters out null-data
packets as well as management packets. This makes it impossible for
mac80211 to monitor the PS mode by using the PM bit of incoming frames.
Disable mac80211 automatic link PS-mode handling by supporting
IEEE80211_HW_AP_LINK_PS in HW flags.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Report a TX rate idx of -1 and count 0 when returning untransmitted
skbs to mac80211 using ieee80211_tx_status(). Otherwise mac80211
tries to use the returned (essentially garbage) status.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When operating in AP-mode we require a per link tx-queue.
This allows us to implement HW assisted PS mode for links,
as well as regulate per-link FW TX blocks consumption.
Split each link into ACs to support future QoS for AP-mode.
AC queues are emptied in priority and per-link queues are
scheduled in a simple round-robin fashion.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If a sta starts transmitting immediately after authentication, sometimes
the FW deauthenticates it. Fix this by marking the sta "in-connection"
in FW before sending the autentication response.
The "in-connection" entry is automatically removed when connection
succeeds or after a timeout.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Check the conditions for the high/low TX queue watermarks when the
spin-lock is taken. This prevents race conditions as tx_queue_count and
the flag checked are only modified when the spin-lock is taken.
The following race was in mind:
- Queues are almost full and wl1271_op_tx() will stop the queues, but it
doesn't get the spin-lock yet.
- (on another CPU) tx_work_locked() dequeues 15 skbs from this queue and
tx_queue_count is updated to reflect this
- wl1271_op_tx() does not check tx_queue_count after taking the
spin-lock and incorrectly stops the queue.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The mac_address should be set also when ht caps are disabled.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the standard ALIGN() macro instead of redefining similar macros.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx fw supports ack status reporting for tx frames, so
add the IEEE80211_HW_REPORTS_TX_ACK_STATUS flag to our supported
features.
Since we do the rate control in the fw, we'll probably want
to adjust the STA_LOST_PKT_THRESHOLD heuristics in the future, to
account for retransmissions as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
