Subsequent patches are going to add per-{Port, VLAN} neighbor
suppression, which will require br_flood() to potentially suppress ARP /
NS packets on a per-{Port, VLAN} basis.
As a preparation, pass the VLAN ID of the packet as another argument to
br_flood().
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge does not flood ARP / NS packets for which a reply was sent to
bridge ports that have neighbor suppression enabled.
Subsequent patches are going to add per-{Port, VLAN} neighbor
suppression, which is going to make it more expensive to check whether
neighbor suppression is enabled since a VLAN lookup will be required.
Therefore, instead of unnecessarily performing this lookup for every
packet, only perform it for ARP / NS packets for which a reply was sent.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a structural problem in switchdev, where the flag bits in
struct switchdev_notifier_fdb_info (added_by_user, is_local etc) only
represent a simplified / denatured view of what's in struct
net_bridge_fdb_entry :: flags (BR_FDB_ADDED_BY_USER, BR_FDB_LOCAL etc).
Each time we want to pass more information about struct
net_bridge_fdb_entry :: flags to struct switchdev_notifier_fdb_info
(here, BR_FDB_STATIC), we find that FDB entries were already notified to
switchdev with no regard to this flag, and thus, switchdev drivers had
no indication whether the notified entries were static or not.
For example, this command:
ip link add br0 type bridge && ip link set swp0 master br0
bridge fdb add dev swp0 00:01:02:03:04:05 master dynamic
has never worked as intended with switchdev. It causes a struct
net_bridge_fdb_entry to be passed to br_switchdev_fdb_notify() which has
a single flag set: BR_FDB_ADDED_BY_USER.
This is further passed to the switchdev notifier chain, where interested
drivers have no choice but to assume this is a static (does not age) and
sticky (does not migrate) FDB entry. So currently, all drivers offload
it to hardware as such, as can be seen below ("offload" is set).
bridge fdb get 00:01:02:03:04:05 dev swp0 master
00:01:02:03:04:05 dev swp0 offload master br0
The software FDB entry expires $ageing_time centiseconds after the
kernel last sees a packet with this MAC SA, and the bridge notifies its
deletion as well, so it eventually disappears from hardware too.
This is a problem, because it is actually desirable to start offloading
"master dynamic" FDB entries correctly - they should expire $ageing_time
centiseconds after the *hardware* port last sees a packet with this
MAC SA - and this is how the current incorrect behavior was discovered.
With an offloaded data plane, it can be expected that software only sees
exception path packets, so an otherwise active dynamic FDB entry would
be aged out by software sooner than it should.
With the change in place, these FDB entries are no longer offloaded:
bridge fdb get 00:01:02:03:04:05 dev swp0 master
00:01:02:03:04:05 dev swp0 master br0
and this also constitutes a better way (assuming a backport to stable
kernels) for user space to determine whether the kernel has the
capability of doing something sane with these or not.
As opposed to "master dynamic" FDB entries, on the current behavior of
which no one currently depends on (which can be deduced from the lack of
kselftests), Ido Schimmel explains that entries with the "extern_learn"
flag (BR_FDB_ADDED_BY_EXT_LEARN) should still be notified to switchdev,
since the spectrum driver listens to them (and this is kind of okay,
because although they are treated identically to "static", they are
expected to not age, and to roam).
Fixes: 6b26b51b1d ("net: bridge: Add support for notifying devices about FDB add/del")
Link: https://lore.kernel.org/netdev/20230327115206.jk5q5l753aoelwus@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20230418155902.898627-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Recent attempt to ensure PREROUTING hook is executed again when a
decrypted ipsec packet received on a bridge passes through the network
stack a second time broke the physdev match in INPUT hook.
We can't discard the nf_bridge info strct from sabotage_in hook, as
this is needed by the physdev match.
Keep the struct around and handle this with another conditional instead.
Fixes: 2b272bb558 ("netfilter: br_netfilter: disable sabotage_in hook after first suppression")
Reported-and-tested-by: Farid BENAMROUCHE <fariouche@yahoo.fr>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Under high contention dst_entry::__refcnt becomes a significant bottleneck.
atomic_inc_not_zero() is implemented with a cmpxchg() loop, which goes into
high retry rates on contention.
Switch the reference count to rcuref_t which results in a significant
performance gain. Rename the reference count member to __rcuref to reflect
the change.
The gain depends on the micro-architecture and the number of concurrent
operations and has been measured in the range of +25% to +130% with a
localhost memtier/memcached benchmark which amplifies the problem
massively.
Running the memtier/memcached benchmark over a real (1Gb) network
connection the conversion on top of the false sharing fix for struct
dst_entry::__refcnt results in a total gain in the 2%-5% range over the
upstream baseline.
Reported-by: Wangyang Guo <wangyang.guo@intel.com>
Reported-by: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230307125538.989175656@linutronix.de
Link: https://lore.kernel.org/r/20230323102800.215027837@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the upcoming VXLAN MDB implementation, the 0.0.0.0 and :: MDB entries
will act as catchall entries for unregistered IP multicast traffic in a
similar fashion to the 00:00:00:00:00:00 VXLAN FDB entry that is used to
transmit BUM traffic.
In deployments where inter-subnet multicast forwarding is used, not all
the VTEPs in a tenant domain are members in all the broadcast domains.
It is therefore advantageous to transmit BULL (broadcast, unknown
unicast and link-local multicast) and unregistered IP multicast traffic
on different tunnels. If the same tunnel was used, a VTEP only
interested in IP multicast traffic would also pull all the BULL traffic
and drop it as it is not a member in the originating broadcast domain
[1].
Prepare for this change by allowing the 0.0.0.0 group address in the
common rtnetlink MDB code and forbid it in the bridge driver. A similar
change is not needed for IPv6 because the common code only validates
that the group address is not the all-nodes address.
[1] https://datatracker.ietf.org/doc/html/draft-ietf-bess-evpn-irb-mcast#section-2.6
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the bridge driver registers handlers for MDB netlink
messages, making it impossible for other drivers to implement MDB
support.
As a preparation for VXLAN MDB support, move the MDB handlers out of the
bridge driver to the core rtnetlink code. The rtnetlink code will call
into individual drivers by invoking their previously added MDB net
device operations.
Note that while the diffstat is large, the change is mechanical. It
moves code out of the bridge driver to rtnetlink code. Also note that a
similar change was made in 2012 with commit 77162022ab ("net: add
generic PF_BRIDGE:RTM_ FDB hooks") that moved FDB handlers out of the
bridge driver to the core rtnetlink code.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the previously added MDB net device operations in the bridge
driver so that they could be invoked by core rtnetlink code in the next
patch.
The operations are identical to the existing br_mdb_{dump,add,del}
functions. The '_new' suffix will be removed in the next patch. The
functions are re-implemented in this patch to make the conversion in the
next patch easier to review.
Add dummy implementations when 'CONFIG_BRIDGE_IGMP_SNOOPING' is
disabled, so that an error will be returned to user space when it is
trying to add or delete an MDB entry. This is consistent with existing
behavior where the bridge driver does not even register rtnetlink
handlers for RTM_{NEW,DEL,GET}MDB messages when this Kconfig option is
disabled.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have many lockless accesses to n->nud_state.
Before adding another one in the following patch,
add annotations to readers and writers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename br_nf_check_hbh_len() to nf_ip6_check_hbh_len() and move it
to netfilter utils, so that it can be used by other modules, like
ovs and tc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
br_nf_check_hbh_len() is a function to check the Hop-by-hop option
header, and shouldn't do pskb_trim_rcsum() there. This patch is to
pass pkt_len out to br_validate_ipv6() and do pskb_trim_rcsum()
after calling br_validate_ipv6() instead.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
In the while loop of br_nf_check_hbh_len(), similar to ip6_parse_tlv(),
before accessing 'nh[off + 1]', it should add a check 'len < 2'; and
before parsing IPV6_TLV_JUMBO, it should add a check 'optlen > len',
in case of overflows.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
When checking Hop-by-hop option header, if the option data is in
nonlinear area, it should do pskb_may_pull instead of discarding
the skb as a bad IPv6 packet.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
nftables equivalent for ebtables -t broute.
Implement broute meta statement to set br_netfilter_broute flag
in skb to force a packet to be routed instead of being bridged.
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Florian Westphal <fw@strlen.de>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Fix broken listing of set elements when table has an owner.
2) Fix conntrack refcount leak in ctnetlink with related conntrack
entries, from Hangyu Hua.
3) Fix use-after-free/double-free in ctnetlink conntrack insert path,
from Florian Westphal.
4) Fix ip6t_rpfilter with VRF, from Phil Sutter.
5) Fix use-after-free in ebtables reported by syzbot, also from Florian.
6) Use skb->len in xt_length to deal with IPv6 jumbo packets,
from Xin Long.
7) Fix NETLINK_LISTEN_ALL_NSID with ctnetlink, from Florian Westphal.
8) Fix memleak in {ip_,ip6_,arp_}tables in ENOMEM error case,
from Pavel Tikhomirov.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: x_tables: fix percpu counter block leak on error path when creating new netns
netfilter: ctnetlink: make event listener tracking global
netfilter: xt_length: use skb len to match in length_mt6
netfilter: ebtables: fix table blob use-after-free
netfilter: ip6t_rpfilter: Fix regression with VRF interfaces
netfilter: conntrack: fix rmmod double-free race
netfilter: ctnetlink: fix possible refcount leak in ctnetlink_create_conntrack()
netfilter: nf_tables: allow to fetch set elements when table has an owner
====================
Link: https://lore.kernel.org/r/20230222092137.88637-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We are not allowed to return an error at this point.
Looking at the code it looks like ret is always 0 at this
point, but its not.
t = find_table_lock(net, repl->name, &ret, &ebt_mutex);
... this can return a valid table, with ret != 0.
This bug causes update of table->private with the new
blob, but then frees the blob right away in the caller.
Syzbot report:
BUG: KASAN: vmalloc-out-of-bounds in __ebt_unregister_table+0xc00/0xcd0 net/bridge/netfilter/ebtables.c:1168
Read of size 4 at addr ffffc90005425000 by task kworker/u4:4/74
Workqueue: netns cleanup_net
Call Trace:
kasan_report+0xbf/0x1f0 mm/kasan/report.c:517
__ebt_unregister_table+0xc00/0xcd0 net/bridge/netfilter/ebtables.c:1168
ebt_unregister_table+0x35/0x40 net/bridge/netfilter/ebtables.c:1372
ops_exit_list+0xb0/0x170 net/core/net_namespace.c:169
cleanup_net+0x4ee/0xb10 net/core/net_namespace.c:613
...
ip(6)tables appears to be ok (ret should be 0 at this point) but make
this more obvious.
Fixes: c58dd2dd44 ("netfilter: Can't fail and free after table replacement")
Reported-by: syzbot+f61594de72d6705aea03@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since commit ee6d3dd4ed ("driver core: make kobj_type constant.")
the driver core allows the usage of const struct kobj_type.
Take advantage of this to constify the structure definition to prevent
modification at runtime.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Future patches are going to move parts of the bridge MDB code to the
common rtnetlink code in preparation for VXLAN MDB support. To
facilitate code sharing between both drivers, move the validation of the
top level attributes in RTM_{NEW,DEL}MDB messages to a policy that will
eventually be moved to the rtnetlink code.
Use 'NLA_NESTED' for 'MDBA_SET_ENTRY_ATTRS' instead of
NLA_POLICY_NESTED() as this attribute is going to be validated using
different policies in the underlying drivers.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The purpose of the sequence generation counter in the netlink callback
is to identify if a multipart dump is consistent or not by calling
nl_dump_check_consistent() whenever a message is generated.
The function is not invoked by the MDB code, rendering the sequence
generation counter assignment pointless. Remove it.
Note that even if the function was invoked, we still could not
accurately determine if the dump is consistent or not, as there is no
sequence generation counter for MDB entries, unlike nexthop objects, for
example.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'MDB_PG_FLAGS_PERMANENT' and 'MDB_PERMANENT' happen to have the same
value, but the latter is uAPI and cannot change, so use it when dumping
an MDB entry.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous patch added accounting for number of MDB entries per port and
per port-VLAN, and the logic to verify that these values stay within
configured bounds. However it didn't provide means to actually configure
those bounds or read the occupancy. This patch does that.
Two new netlink attributes are added for the MDB occupancy:
IFLA_BRPORT_MCAST_N_GROUPS for the per-port occupancy and
BRIDGE_VLANDB_ENTRY_MCAST_N_GROUPS for the per-port-VLAN occupancy.
And another two for the maximum number of MDB entries:
IFLA_BRPORT_MCAST_MAX_GROUPS for the per-port maximum, and
BRIDGE_VLANDB_ENTRY_MCAST_MAX_GROUPS for the per-port-VLAN one.
Note that the two new IFLA_BRPORT_ attributes prompt bumping of
RTNL_SLAVE_MAX_TYPE to size the slave attribute tables large enough.
The new attributes are used like this:
# ip link add name br up type bridge vlan_filtering 1 mcast_snooping 1 \
mcast_vlan_snooping 1 mcast_querier 1
# ip link set dev v1 master br
# bridge vlan add dev v1 vid 2
# bridge vlan set dev v1 vid 1 mcast_max_groups 1
# bridge mdb add dev br port v1 grp 230.1.2.3 temp vid 1
# bridge mdb add dev br port v1 grp 230.1.2.4 temp vid 1
Error: bridge: Port-VLAN is already in 1 groups, and mcast_max_groups=1.
# bridge link set dev v1 mcast_max_groups 1
# bridge mdb add dev br port v1 grp 230.1.2.3 temp vid 2
Error: bridge: Port is already in 1 groups, and mcast_max_groups=1.
# bridge -d link show
5: v1@v2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 master br [...]
[...] mcast_n_groups 1 mcast_max_groups 1
# bridge -d vlan show
port vlan-id
br 1 PVID Egress Untagged
state forwarding mcast_router 1
v1 1 PVID Egress Untagged
[...] mcast_n_groups 1 mcast_max_groups 1
2
[...] mcast_n_groups 0 mcast_max_groups 0
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDB maintained by the bridge is limited. When the bridge is configured
for IGMP / MLD snooping, a buggy or malicious client can easily exhaust its
capacity. In SW datapath, the capacity is configurable through the
IFLA_BR_MCAST_HASH_MAX parameter, but ultimately is finite. Obviously a
similar limit exists in the HW datapath for purposes of offloading.
In order to prevent the issue of unilateral exhaustion of MDB resources,
introduce two parameters in each of two contexts:
- Per-port and per-port-VLAN number of MDB entries that the port
is member in.
- Per-port and (when BROPT_MCAST_VLAN_SNOOPING_ENABLED is enabled)
per-port-VLAN maximum permitted number of MDB entries, or 0 for
no limit.
The per-port multicast context is used for tracking of MDB entries for the
port as a whole. This is available for all bridges.
The per-port-VLAN multicast context is then only available on
VLAN-filtering bridges on VLANs that have multicast snooping on.
With these changes in place, it will be possible to configure MDB limit for
bridge as a whole, or any one port as a whole, or any single port-VLAN.
Note that unlike the global limit, exhaustion of the per-port and
per-port-VLAN maximums does not cause disablement of multicast snooping.
It is also permitted to configure the local limit larger than hash_max,
even though that is not useful.
In this patch, introduce only the accounting for number of entries, and the
max field itself, but not the means to toggle the max. The next patch
introduces the netlink APIs to toggle and read the values.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is getting more to clean up in the following patches.
Structuring the cleanups in one labeled block will allow reusing the same
cleanup from several places.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since cleaning up the effects of br_multicast_new_port_group() just
consists of delisting and freeing the memory, the function
br_mdb_add_group_star_g() inlines the corresponding code. In the following
patches, number of per-port and per-port-VLAN MDB entries is going to be
maintained, and that counter will have to be updated. Because that logic
is going to be hidden in the br_multicast module, introduce a new hook
intended to again remove a newly-created group.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that br_multicast_new_port_group() takes an extack argument, move
setting the extack there. The downside is that the error messages end
up being less specific (the function cannot distinguish between (S,G)
and (*,G) groups). However, the alternative is to check in the caller
whether the callee set the extack, and if it didn't, set it. But that
is only done when the callee is not exactly known. (E.g. in case of a
notifier invocation.)
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it possible to set an extack in br_multicast_new_port_group().
Eventually, this function will check for per-port and per-port-vlan
MDB maximums, and will use the extack to communicate the reason for
the bounce.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make any attributes newly-added to br_port_policy or vlan_tunnel_policy
parsed strictly, to prevent userspace from passing garbage. Note that this
patchset only touches the former policy. The latter was adjusted for
completeness' sake. There do not appear to be other _deprecated calls
with non-NULL policies.
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netdev common pattern, extack pointer is forwarded to the drivers
to be filled with error message. However, the caller can easily
overwrite the filled message.
Instead of adding multiple "if (!extack->_msg)" checks before any
NL_SET_ERR_MSG() call, which appears after call to the driver, let's
add new macro to common code.
[1] https://lore.kernel.org/all/Y9Irgrgf3uxOjwUm@unreal
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/6993fac557a40a1973dfa0095107c3d03d40bec1.1675171790.git.leon@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These 3 places in bridge netfilter are called on RX path after GRO
and IPv4 TCP GSO packets may come through, so replace iph tot_len
accessing with skb_ip_totlen() in there.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When using a xfrm interface in a bridged setup (the outgoing device is
bridged), the incoming packets in the xfrm interface are only tracked
in the outgoing direction.
$ brctl show
bridge name interfaces
br_eth1 eth1
$ conntrack -L
tcp 115 SYN_SENT src=192... dst=192... [UNREPLIED] ...
If br_netfilter is enabled, the first (encrypted) packet is received onR
eth1, conntrack hooks are called from br_netfilter emulation which
allocates nf_bridge info for this skb.
If the packet is for local machine, skb gets passed up the ip stack.
The skb passes through ip prerouting a second time. br_netfilter
ip_sabotage_in supresses the re-invocation of the hooks.
After this, skb gets decrypted in xfrm layer and appears in
network stack a second time (after decryption).
Then, ip_sabotage_in is called again and suppresses netfilter
hook invocation, even though the bridge layer never called them
for the plaintext incarnation of the packet.
Free the bridge info after the first suppression to avoid this.
I was unable to figure out where the regression comes from, as far as i
can see br_netfilter always had this problem; i did not expect that skb
is looped again with different headers.
Fixes: c4b0e771f9 ("netfilter: avoid using skb->nf_bridge directly")
Reported-and-tested-by: Wolfgang Nothdurft <wolfgang@linogate.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass in
a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be used
no matter what the const value is. This prevents every subsystem from
having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject, objects
as being "non-mutable". The changes to the kobject and driver core in
this pull request are the result of that, as there are lots of paths
where kobjects and device pointers are not modified at all, so marking
them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object rules.
All of this has been bike-shedded in quite a lot of detail on lkml with
different names and implementations resulting in the tiny version we
have in here, much better than my original proposal. Lots of subsystem
maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with no
problems, OTHER than some merge issues with other trees that should be
obvious when you hit them (block tree deletes a driver that this tree
modifies, iommufd tree modifies code that this tree also touches). If
there are merge problems with these trees, please let me know.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wz3A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yks0ACeKYUlVgCsER8eYW+x18szFa2QTXgAn2h/VhZe
1Fp53boFaQkGBjl8mGF8
=v+FB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass
in a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be
used no matter what the const value is. This prevents every subsystem
from having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject,
objects as being "non-mutable". The changes to the kobject and driver
core in this pull request are the result of that, as there are lots of
paths where kobjects and device pointers are not modified at all, so
marking them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object
rules.
All of this has been bike-shedded in quite a lot of detail on lkml
with different names and implementations resulting in the tiny version
we have in here, much better than my original proposal. Lots of
subsystem maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with
no problems"
* tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (58 commits)
device property: Fix documentation for fwnode_get_next_parent()
firmware_loader: fix up to_fw_sysfs() to preserve const
usb.h: take advantage of container_of_const()
device.h: move kobj_to_dev() to use container_of_const()
container_of: add container_of_const() that preserves const-ness of the pointer
driver core: fix up missed drivers/s390/char/hmcdrv_dev.c class.devnode() conversion.
driver core: fix up missed scsi/cxlflash class.devnode() conversion.
driver core: fix up some missing class.devnode() conversions.
driver core: make struct class.devnode() take a const *
driver core: make struct class.dev_uevent() take a const *
cacheinfo: Remove of_node_put() for fw_token
device property: Add a blank line in Kconfig of tests
device property: Rename goto label to be more precise
device property: Move PROPERTY_ENTRY_BOOL() a bit down
device property: Get rid of __PROPERTY_ENTRY_ARRAY_EL*SIZE*()
kernfs: fix all kernel-doc warnings and multiple typos
driver core: pass a const * into of_device_uevent()
kobject: kset_uevent_ops: make name() callback take a const *
kobject: kset_uevent_ops: make filter() callback take a const *
kobject: make kobject_namespace take a const *
...
Now that user space can specify additional attributes of port group
entries such as filter mode and source list, it makes sense to allow
user space to atomically modify these attributes by replacing entries
instead of forcing user space to delete the entries and add them back.
Replace MDB port group entries when the 'NLM_F_REPLACE' flag is
specified in the netlink message header.
When a (*, G) entry is replaced, update the following attributes: Source
list, state, filter mode, protocol and flags. If the entry is temporary
and in EXCLUDE mode, reset the group timer to the group membership
interval. If the entry is temporary and in INCLUDE mode, reset the
source timers of associated sources to the group membership interval.
Examples:
# bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 permanent source_list 192.0.2.1,192.0.2.2 filter_mode include
# bridge -d -s mdb show
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.2 permanent filter_mode include proto static 0.00
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include proto static 0.00
dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode include source_list 192.0.2.2/0.00,192.0.2.1/0.00 proto static 0.00
# bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 permanent source_list 192.0.2.1,192.0.2.3 filter_mode exclude proto zebra
# bridge -d -s mdb show
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.3 permanent filter_mode include proto zebra blocked 0.00
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include proto zebra blocked 0.00
dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode exclude source_list 192.0.2.3/0.00,192.0.2.1/0.00 proto zebra 0.00
# bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 temp source_list 192.0.2.4,192.0.2.3 filter_mode include proto bgp
# bridge -d -s mdb show
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.4 temp filter_mode include proto bgp 0.00
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.3 temp filter_mode include proto bgp 0.00
dev br0 port dummy10 grp 239.1.1.1 temp filter_mode include source_list 192.0.2.4/259.44,192.0.2.3/259.44 proto bgp 0.00
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the 'MDBE_ATTR_RTPORT' attribute to allow user space to specify the
routing protocol of the MDB port group entry. Enforce a minimum value of
'RTPROT_STATIC' to prevent user space from using protocol values that
should only be set by the kernel (e.g., 'RTPROT_KERNEL'). Maintain
backward compatibility by defaulting to 'RTPROT_STATIC'.
The protocol is already visible to user space in RTM_NEWMDB responses
and notifications via the 'MDBA_MDB_EATTR_RTPROT' attribute.
The routing protocol allows a routing daemon to distinguish between
entries configured by it and those configured by the administrator. Once
MDB flush is supported, the protocol can be used as a criterion
according to which the flush is performed.
Examples:
# bridge mdb add dev br0 port dummy10 grp 239.1.1.1 permanent proto kernel
Error: integer out of range.
# bridge mdb add dev br0 port dummy10 grp 239.1.1.1 permanent proto static
# bridge mdb add dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent proto zebra
# bridge mdb add dev br0 port dummy10 grp 239.1.1.2 permanent source_list 198.51.100.1,198.51.100.2 filter_mode include proto 250
# bridge -d mdb show
dev br0 port dummy10 grp 239.1.1.2 src 198.51.100.2 permanent filter_mode include proto 250
dev br0 port dummy10 grp 239.1.1.2 src 198.51.100.1 permanent filter_mode include proto 250
dev br0 port dummy10 grp 239.1.1.2 permanent filter_mode include source_list 198.51.100.2/0.00,198.51.100.1/0.00 proto 250
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include proto zebra
dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode exclude proto static
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new netlink attributes to the RTM_NEWMDB request that allow user
space to add (*, G) with a source list and filter mode.
The RTM_NEWMDB message can already dump such entries (created by the
kernel) so there is no need to add dump support. However, the message
contains a different set of attributes depending if it is a request or a
response. The naming and structure of the new attributes try to follow
the existing ones used in the response.
Request:
[ struct nlmsghdr ]
[ struct br_port_msg ]
[ MDBA_SET_ENTRY ]
struct br_mdb_entry
[ MDBA_SET_ENTRY_ATTRS ]
[ MDBE_ATTR_SOURCE ]
struct in_addr / struct in6_addr
[ MDBE_ATTR_SRC_LIST ] // new
[ MDBE_SRC_LIST_ENTRY ]
[ MDBE_SRCATTR_ADDRESS ]
struct in_addr / struct in6_addr
[ ...]
[ MDBE_ATTR_GROUP_MODE ] // new
u8
Response:
[ struct nlmsghdr ]
[ struct br_port_msg ]
[ MDBA_MDB ]
[ MDBA_MDB_ENTRY ]
[ MDBA_MDB_ENTRY_INFO ]
struct br_mdb_entry
[ MDBA_MDB_EATTR_TIMER ]
u32
[ MDBA_MDB_EATTR_SOURCE ]
struct in_addr / struct in6_addr
[ MDBA_MDB_EATTR_RTPROT ]
u8
[ MDBA_MDB_EATTR_SRC_LIST ]
[ MDBA_MDB_SRCLIST_ENTRY ]
[ MDBA_MDB_SRCATTR_ADDRESS ]
struct in_addr / struct in6_addr
[ MDBA_MDB_SRCATTR_TIMER ]
u8
[...]
[ MDBA_MDB_EATTR_GROUP_MODE ]
u8
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for allowing user space to add (*, G) entries with a
source list and associated filter mode, add the necessary plumbing to
handle such requests.
Extend the MDB configuration structure with a currently empty source
array and filter mode that is currently hard coded to EXCLUDE.
Add the source entries and the corresponding (S, G) entries before
making the new (*, G) port group entry visible to the data path.
Handle the creation of each source entry in a similar fashion to how it
is created from the data path in response to received Membership
Reports: Create the source entry, arm the source timer (if needed), add
a corresponding (S, G) forwarding entry and finally mark the source
entry as installed (by user space).
Add the (S, G) entry by populating an MDB configuration structure and
calling br_mdb_add_group_sg() as if a new entry is created by user
space, with the sole difference that the 'src_entry' field is set to
make sure that the group timer of such entries is never armed.
Note that it is not currently possible to add more than 32 source
entries to a port group entry. If this proves to be a problem we can
either increase 'PG_SRC_ENT_LIMIT' or avoid forcing a limit on entries
created by user space.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
User space will soon be able to install a (*, G) with a source list,
prompting the creation of a (S, G) entry for each source.
In this case, the group timer of the (S, G) entry should never be set.
Solve this by adding a new field to the MDB configuration structure that
denotes whether the (S, G) corresponds to a source or not.
The field will be set in a subsequent patch where br_mdb_add_group_sg()
is called in order to create a (S, G) entry for each user provided
source.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are a few places where the bridge driver differentiates between
(S, G) entries installed by the kernel (in response to Membership
Reports) and those installed by user space. One of them is when deleting
an (S, G) entry corresponding to a source entry that is being deleted.
While user space cannot currently add a source entry to a (*, G), it can
add an (S, G) entry that later corresponds to a source entry created by
the reception of a Membership Report. If this source entry is later
deleted because its source timer expired or because the (*, G) entry is
being deleted, the bridge driver will not delete the corresponding (S,
G) entry if it was added by user space as permanent.
This is going to be a problem when the ability to install a (*, G) with
a source list is exposed to user space. In this case, when user space
installs the (*, G) as permanent, then all the (S, G) entries
corresponding to its source list will also be installed as permanent.
When user space deletes the (*, G), all the source entries will be
deleted and the expectation is that the corresponding (S, G) entries
will be deleted as well.
Solve this by introducing a new source entry flag denoting that the
entry was installed by user space. When the entry is deleted, delete the
corresponding (S, G) entry even if it was installed by user space as
permanent, as the flag tells us that it was installed in response to the
source entry being created.
The flag will be set in a subsequent patch where source entries are
created in response to user requests.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Expose __br_multicast_del_group_src() which is symmetric to
br_multicast_new_group_src() and does not remove the installed {S, G}
forwarding entry, unlike br_multicast_del_group_src().
The function will be used in the error path when user space was able to
add a new source entry, but failed to install a corresponding forwarding
entry.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, new group source entries are only created in response to
received Membership Reports. Subsequent patches are going to allow user
space to install (*, G) entries with a source list.
As a preparatory step, expose br_multicast_new_group_src() so that it
could later be invoked from the MDB code (i.e., br_mdb.c) that handles
RTM_NEWMDB messages.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Subsequent patches will add memory allocations in br_mdb_config_init()
as the MDB configuration structure will include a linked list of source
entries. This memory will need to be freed regardless if br_mdb_add()
succeeded or failed.
As a preparation for this change, add a centralized error path where the
memory will be freed.
Note that br_mdb_del() already has one error path and therefore does not
require any changes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Subsequent patches are going to add additional validation functions and
netlink policies. Some of these functions will need to perform parsing
using nla_parse_nested() and the new policies.
In order to keep all the policies next to each other, move the current
policy to before the validation functions.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the bridge is using IGMP version 3 or MLD version 2, it handles the
addition of (*, G) and (S, G) entries differently.
When a new (S, G) port group entry is added, all the (*, G) EXCLUDE
ports need to be added to the port group of the new entry. Similarly,
when a new (*, G) EXCLUDE port group entry is added, the port needs to
be added to the port group of all the matching (S, G) entries.
Subsequent patches will create more differences between both entry
types. Namely, filter mode and source list can only be specified for (*,
G) entries.
Given the current and future differences between both entry types,
handle the addition of each entry type in a different function, thereby
avoiding the creation of one complex function.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the filter mode (i.e., INCLUDE / EXCLUDE) of MDB entries
cannot be set from user space. Instead, it is set by the kernel
according to the entry type: (*, G) entries are treated as EXCLUDE and
(S, G) entries are treated as INCLUDE. This allows the kernel to derive
the entry type from its filter mode.
Subsequent patches will allow user space to set the filter mode of (*,
G) entries, making the current assumption incorrect.
As a preparation, remove the current assumption and instead determine
the entry type from its key, which is a more direct way.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
1) Incorrect error check in nft_expr_inner_parse(), from Dan Carpenter.
2) Add DATA_SENT state to SCTP connection tracking helper, from
Sriram Yagnaraman.
3) Consolidate nf_confirm for ipv4 and ipv6, from Florian Westphal.
4) Add bitmask support for ipset, from Vishwanath Pai.
5) Handle icmpv6 redirects as RELATED, from Florian Westphal.
6) Add WARN_ON_ONCE() to impossible case in flowtable datapath,
from Li Qiong.
7) A large batch of IPVS updates to replace timer-based estimators by
kthreads to scale up wrt. CPUs and workload (millions of estimators).
Julian Anastasov says:
This patchset implements stats estimation in kthread context.
It replaces the code that runs on single CPU in timer context every 2
seconds and causing latency splats as shown in reports [1], [2], [3].
The solution targets setups with thousands of IPVS services,
destinations and multi-CPU boxes.
Spread the estimation on multiple (configured) CPUs and multiple
time slots (timer ticks) by using multiple chains organized under RCU
rules. When stats are not needed, it is recommended to use
run_estimation=0 as already implemented before this change.
RCU Locking:
- As stats are now RCU-locked, tot_stats, svc and dest which
hold estimator structures are now always freed from RCU
callback. This ensures RCU grace period after the
ip_vs_stop_estimator() call.
Kthread data:
- every kthread works over its own data structure and all
such structures are attached to array. For now we limit
kthreads depending on the number of CPUs.
- even while there can be a kthread structure, its task
may not be running, eg. before first service is added or
while the sysctl var is set to an empty cpulist or
when run_estimation is set to 0 to disable the estimation.
- the allocated kthread context may grow from 1 to 50
allocated structures for timer ticks which saves memory for
setups with small number of estimators
- a task and its structure may be released if all
estimators are unlinked from its chains, leaving the
slot in the array empty
- every kthread data structure allows limited number
of estimators. Kthread 0 is also used to initially
calculate the max number of estimators to allow in every
chain considering a sub-100 microsecond cond_resched
rate. This number can be from 1 to hundreds.
- kthread 0 has an additional job of optimizing the
adding of estimators: they are first added in
temp list (est_temp_list) and later kthread 0
distributes them to other kthreads. The optimization
is based on the fact that newly added estimator
should be estimated after 2 seconds, so we have the
time to offload the adding to chain from controlling
process to kthread 0.
- to add new estimators we use the last added kthread
context (est_add_ktid). The new estimators are linked to
the chains just before the estimated one, based on add_row.
This ensures their estimation will start after 2 seconds.
If estimators are added in bursts, common case if all
services and dests are initially configured, we may
spread the estimators to more chains and as result,
reducing the initial delay below 2 seconds.
Many thanks to Jiri Wiesner for his valuable comments
and for spending a lot of time reviewing and testing
the changes on different platforms with 48-256 CPUs and
1-8 NUMA nodes under different cpufreq governors.
The new IPVS estimators do not use workqueue infrastructure
because:
- The estimation can take long time when using multiple IPVS rules (eg.
millions estimator structures) and especially when box has multiple
CPUs due to the for_each_possible_cpu usage that expects packets from
any CPU. With est_nice sysctl we have more control how to prioritize the
estimation kthreads compared to other processes/kthreads that have
latency requirements (such as servers). As a benefit, we can see these
kthreads in top and decide if we will need some further control to limit
their CPU usage (max number of structure to estimate per kthread).
- with kthreads we run code that is read-mostly, no write/lock
operations to process the estimators in 2-second intervals.
- work items are one-shot: as estimators are processed every
2 seconds, they need to be re-added every time. This again
loads the timers (add_timer) if we use delayed works, as there are
no kthreads to do the timings.
[1] Report from Yunhong Jiang:
https://lore.kernel.org/netdev/D25792C1-1B89-45DE-9F10-EC350DC04ADC@gmail.com/
[2] https://marc.info/?l=linux-virtual-server&m=159679809118027&w=2
[3] Report from Dust:
https://archive.linuxvirtualserver.org/html/lvs-devel/2020-12/msg00000.html
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
ipvs: run_estimation should control the kthread tasks
ipvs: add est_cpulist and est_nice sysctl vars
ipvs: use kthreads for stats estimation
ipvs: use u64_stats_t for the per-cpu counters
ipvs: use common functions for stats allocation
ipvs: add rcu protection to stats
netfilter: flowtable: add a 'default' case to flowtable datapath
netfilter: conntrack: set icmpv6 redirects as RELATED
netfilter: ipset: Add support for new bitmask parameter
netfilter: conntrack: merge ipv4+ipv6 confirm functions
netfilter: conntrack: add sctp DATA_SENT state
netfilter: nft_inner: fix IS_ERR() vs NULL check
====================
Link: https://lore.kernel.org/r/20221211101204.1751-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'group' argument is not modified, so mark it as 'const'. It will
allow us to constify arguments of the callers of this function in future
patches.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop the first three arguments and instead extract them from the MDB
configuration structure.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The checks only require information parsed from the RTM_NEWMDB netlink
message and do not rely on any state stored in the bridge driver.
Therefore, there is no need to perform the checks in the critical
section under the multicast lock.
Move the checks out of the critical section.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The parsing of the netlink messages and the validity checks are now
performed in br_mdb_config_init() so we can remove br_mdb_parse().
This finally allows us to stop passing netlink attributes deep in the
MDB control path and only use the MDB configuration structure.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MDB group key (i.e., {source, destination, protocol, VID}) is
currently determined under the multicast lock from the netlink
attributes. Instead, use the group key from the MDB configuration
structure that was prepared before acquiring the lock.
No functional changes intended.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As an intermediate step towards only using the new MDB configuration
structure, pass it further in the control path instead of passing
individual attributes.
No functional changes intended.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MDB configuration structure (i.e., struct br_mdb_config) now
includes all the necessary information from the parsed RTM_{NEW,DEL}MDB
netlink messages, so use it.
This will later allow us to delete the calls to br_mdb_parse() from
br_mdb_add() and br_mdb_del().
No functional changes intended.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These checks are now redundant as they are performed by
br_mdb_config_init() while parsing the RTM_{NEW,DEL}MDB messages.
Remove them.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Netlink attributes are currently passed deep in the MDB creation call
chain, making it difficult to add new attributes. In addition, some
validity checks are performed under the multicast lock although they can
be performed before it is ever acquired.
As a first step towards solving these issues, parse the RTM_{NEW,DEL}MDB
messages into a configuration structure, relieving other functions from
the need to handle raw netlink attributes.
Subsequent patches will convert the MDB code to use this configuration
structure.
This is consistent with how other rtnetlink objects are handled, such as
routes and nexthops.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
No need to have distinct functions. After merge, ipv6 can avoid
protooff computation if the connection neither needs sequence adjustment
nor helper invocation -- this is the normal case.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The call, kobject_get_ownership(), does not modify the kobject passed
into it, so make it const. This propagates down into the kobj_type
function callbacks so make the kobject passed into them also const,
ensuring that nothing in the kobject is being changed here.
This helps make it more obvious what calls and callbacks do, and do not,
modify structures passed to them.
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Anna Schumaker <anna@kernel.org>
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: Jeff Layton <jlayton@kernel.org>
Cc: linux-nfs@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20221121094649.1556002-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bridge driver can offload VLANs to the underlying hardware either
via switchdev or the 8021q driver. When the former is used, the VLAN is
marked in the bridge driver with the 'BR_VLFLAG_ADDED_BY_SWITCHDEV'
private flag.
To avoid the memory leaks mentioned in the cited commit, the bridge
driver will try to delete a VLAN via the 8021q driver if the VLAN is not
marked with the previously mentioned flag.
When the VLAN protocol of the bridge changes, switchdev drivers are
notified via the 'SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL' attribute, but
the 8021q driver is also called to add the existing VLANs with the new
protocol and delete them with the old protocol.
In case the VLANs were offloaded via switchdev, the above behavior is
both redundant and buggy. Redundant because the VLANs are already
programmed in hardware and drivers that support VLAN protocol change
(currently only mlx5) change the protocol upon the switchdev attribute
notification. Buggy because the 8021q driver is called despite these
VLANs being marked with 'BR_VLFLAG_ADDED_BY_SWITCHDEV'. This leads to
memory leaks [1] when the VLANs are deleted.
Fix by not calling the 8021q driver for VLANs that were already
programmed via switchdev.
[1]
unreferenced object 0xffff8881f6771200 (size 256):
comm "ip", pid 446855, jiffies 4298238841 (age 55.240s)
hex dump (first 32 bytes):
00 00 7f 0e 83 88 ff ff 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000012819ac>] vlan_vid_add+0x437/0x750
[<00000000f2281fad>] __br_vlan_set_proto+0x289/0x920
[<000000000632b56f>] br_changelink+0x3d6/0x13f0
[<0000000089d25f04>] __rtnl_newlink+0x8ae/0x14c0
[<00000000f6276baf>] rtnl_newlink+0x5f/0x90
[<00000000746dc902>] rtnetlink_rcv_msg+0x336/0xa00
[<000000001c2241c0>] netlink_rcv_skb+0x11d/0x340
[<0000000010588814>] netlink_unicast+0x438/0x710
[<00000000e1a4cd5c>] netlink_sendmsg+0x788/0xc40
[<00000000e8992d4e>] sock_sendmsg+0xb0/0xe0
[<00000000621b8f91>] ____sys_sendmsg+0x4ff/0x6d0
[<000000000ea26996>] ___sys_sendmsg+0x12e/0x1b0
[<00000000684f7e25>] __sys_sendmsg+0xab/0x130
[<000000004538b104>] do_syscall_64+0x3d/0x90
[<0000000091ed9678>] entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: 279737939a ("net: bridge: Fix VLANs memory leak")
Reported-by: Vlad Buslov <vladbu@nvidia.com>
Tested-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20221114084509.860831-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
No changes in generated code.
Reported-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20221110085422.521059-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reflect the 'BR_PORT_MAB' flag to device drivers so that:
* Drivers that support MAB could act upon the flag being toggled.
* Drivers that do not support MAB will prevent MAB from being enabled.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the bridge is offloaded to hardware, FDB entries are learned and
aged-out by the hardware. Some device drivers synchronize the hardware
and software FDBs by generating switchdev events towards the bridge.
When a port is locked, the hardware must not learn autonomously, as
otherwise any host will blindly gain authorization. Instead, the
hardware should generate events regarding hosts that are trying to gain
authorization and their MAC addresses should be notified by the device
driver as locked FDB entries towards the bridge driver.
Allow device drivers to notify the bridge driver about such entries by
extending the 'switchdev_notifier_fdb_info' structure with the 'locked'
bit. The bit can only be set by device drivers and not by the bridge
driver.
Prevent a locked entry from being installed if MAB is not enabled on the
bridge port.
If an entry already exists in the bridge driver, reject the locked entry
if the current entry does not have the "locked" flag set or if it points
to a different port. The same semantics are implemented in the software
data path.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, FDB entries that are notified to the bridge via
'SWITCHDEV_FDB_ADD_TO_BRIDGE' are always marked as offloaded. With MAB
enabled, this will no longer be universally true. Device drivers will
report locked FDB entries to the bridge to let it know that the
corresponding hosts required authorization, but it does not mean that
these entries are necessarily programmed in the underlying hardware.
Solve this by determining the offload indication based of the
'offloaded' bit in the FDB notification.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hosts that support 802.1X authentication are able to authenticate
themselves by exchanging EAPOL frames with an authenticator (Ethernet
bridge, in this case) and an authentication server. Access to the
network is only granted by the authenticator to successfully
authenticated hosts.
The above is implemented in the bridge using the "locked" bridge port
option. When enabled, link-local frames (e.g., EAPOL) can be locally
received by the bridge, but all other frames are dropped unless the host
is authenticated. That is, unless the user space control plane installed
an FDB entry according to which the source address of the frame is
located behind the locked ingress port. The entry can be dynamic, in
which case learning needs to be enabled so that the entry will be
refreshed by incoming traffic.
There are deployments in which not all the devices connected to the
authenticator (the bridge) support 802.1X. Such devices can include
printers and cameras. One option to support such deployments is to
unlock the bridge ports connecting these devices, but a slightly more
secure option is to use MAB. When MAB is enabled, the MAC address of the
connected device is used as the user name and password for the
authentication.
For MAB to work, the user space control plane needs to be notified about
MAC addresses that are trying to gain access so that they will be
compared against an allow list. This can be implemented via the regular
learning process with the sole difference that learned FDB entries are
installed with a new "locked" flag indicating that the entry cannot be
used to authenticate the device. The flag cannot be set by user space,
but user space can clear the flag by replacing the entry, thereby
authenticating the device.
Locked FDB entries implement the following semantics with regards to
roaming, aging and forwarding:
1. Roaming: Locked FDB entries can roam to unlocked (authorized) ports,
in which case the "locked" flag is cleared. FDB entries cannot roam
to locked ports regardless of MAB being enabled or not. Therefore,
locked FDB entries are only created if an FDB entry with the given {MAC,
VID} does not already exist. This behavior prevents unauthenticated
devices from disrupting traffic destined to already authenticated
devices.
2. Aging: Locked FDB entries age and refresh by incoming traffic like
regular entries.
3. Forwarding: Locked FDB entries forward traffic like regular entries.
If user space detects an unauthorized MAC behind a locked port and
wishes to prevent traffic with this MAC DA from reaching the host, it
can do so using tc or a different mechanism.
Enable the above behavior using a new bridge port option called "mab".
It can only be enabled on a bridge port that is both locked and has
learning enabled. Locked FDB entries are flushed from the port once MAB
is disabled. A new option is added because there are pure 802.1X
deployments that are not interested in notifications about locked FDB
entries.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The following commands should result in all the dynamic FDB entries
being flushed, but instead all the non-local (non-permanent) entries are
flushed:
# bridge fdb add 00:aa:bb:cc:dd:ee dev dummy1 master static
# bridge fdb add 00:11:22:33:44:55 dev dummy1 master dynamic
# ip link set dev br0 type bridge fdb_flush
# bridge fdb show brport dummy1
00:00:00:00:00:01 master br0 permanent
33:33:00:00:00:01 self permanent
01:00:5e:00:00:01 self permanent
This is because br_fdb_flush() works with FDB flags and not the
corresponding enumerator values. Fix by passing the FDB flag instead.
After the fix:
# bridge fdb add 00:aa:bb:cc:dd:ee dev dummy1 master static
# bridge fdb add 00:11:22:33:44:55 dev dummy1 master dynamic
# ip link set dev br0 type bridge fdb_flush
# bridge fdb show brport dummy1
00:aa:bb:cc:dd:ee master br0 static
00:00:00:00:00:01 master br0 permanent
33:33:00:00:00:01 self permanent
01:00:5e:00:00:01 self permanent
Fixes: 1f78ee14ee ("net: bridge: fdb: add support for fine-grained flushing")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20221101185753.2120691-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.
Convert to the regular interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before creating a new MDB entry, br_multicast_new_group() will call
br_mdb_ip_get() to see if one exists and return it if so.
Therefore, simply call br_multicast_new_group() and omit the call to
br_mdb_ip_get().
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IGMPv3 / MLDv2 Membership Reports are only processed from the data path
with softIRQ disabled, so there is no need to call spin_lock_bh(). Use
spin_lock() instead.
This is consistent with how other IGMP / MLD packets are processed.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As 2.5G, 5G ethernet ports are more common and affordable,
these ports are being used in LAN bridge devices.
STP port_cost() is missing path_cost assignment for these link speeds,
causes highest cost 100 being used.
This result in lower speed port being picked
when there is loop between 5G and 1G ports.
Original path_cost: 10G=2, 1G=4, 100m=19, 10m=100
Adjusted path_cost: 10G=2, 5G=3, 2.5G=4, 1G=5, 100m=19, 10m=100
speed greater than 10G = 1
Signed-off-by: Steven Hsieh <steven.hsieh@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bug fix was incomplete, it "replaced" crash with a memory leak.
The old code had an assignment to "ret" embedded into the conditional,
restore this.
Fixes: 7997eff828 ("netfilter: ebtables: reject blobs that don't provide all entry points")
Reported-and-tested-by: syzbot+a24c5252f3e3ab733464@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The IPv6 path already drops dst in the daddr changed case, but the IPv4
path does not. This change makes the two code paths consistent.
Further, it is possible that there is already a metadata_dst allocated from
ingress that might already be attached to skbuff->dst while following
the bridge path. If it is not released before setting a new
metadata_dst, it will be leaked. This is similar to what is done in
bpf_set_tunnel_key() or ip6_route_input().
It is important to note that the memory being leaked is not the dst
being set in the bridge code, but rather memory allocated from some
other code path that is not being freed correctly before the skb dst is
overwritten.
An example of the leakage fixed by this commit found using kmemleak:
unreferenced object 0xffff888010112b00 (size 256):
comm "softirq", pid 0, jiffies 4294762496 (age 32.012s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 80 16 f1 83 ff ff ff ff ................
e1 4e f6 82 ff ff ff ff 00 00 00 00 00 00 00 00 .N..............
backtrace:
[<00000000d79567ea>] metadata_dst_alloc+0x1b/0xe0
[<00000000be113e13>] udp_tun_rx_dst+0x174/0x1f0
[<00000000a36848f4>] geneve_udp_encap_recv+0x350/0x7b0
[<00000000d4afb476>] udp_queue_rcv_one_skb+0x380/0x560
[<00000000ac064aea>] udp_unicast_rcv_skb+0x75/0x90
[<000000009a8ee8c5>] ip_protocol_deliver_rcu+0xd8/0x230
[<00000000ef4980bb>] ip_local_deliver_finish+0x7a/0xa0
[<00000000d7533c8c>] __netif_receive_skb_one_core+0x89/0xa0
[<00000000a879497d>] process_backlog+0x93/0x190
[<00000000e41ade9f>] __napi_poll+0x28/0x170
[<00000000b4c0906b>] net_rx_action+0x14f/0x2a0
[<00000000b20dd5d4>] __do_softirq+0xf4/0x305
[<000000003a7d7e15>] __irq_exit_rcu+0xc3/0x140
[<00000000968d39a2>] sysvec_apic_timer_interrupt+0x9e/0xc0
[<000000009e920794>] asm_sysvec_apic_timer_interrupt+0x16/0x20
[<000000008942add0>] native_safe_halt+0x13/0x20
Florian Westphal says: "Original code was likely fine because nothing
ever did set a skb->dst entry earlier than bridge in those days."
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Harsh Modi <harshmodi@google.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Harshit Mogalapalli says:
In ebt_do_table() function dereferencing 'private->hook_entry[hook]'
can lead to NULL pointer dereference. [..] Kernel panic:
general protection fault, probably for non-canonical address 0xdffffc0000000005: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f]
[..]
RIP: 0010:ebt_do_table+0x1dc/0x1ce0
Code: 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 5c 16 00 00 48 b8 00 00 00 00 00 fc ff df 49 8b 6c df 08 48 8d 7d 2c 48 89 fa 48 c1 ea 03 <0f> b6 14 02 48 89 f8 83 e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85 88
[..]
Call Trace:
nf_hook_slow+0xb1/0x170
__br_forward+0x289/0x730
maybe_deliver+0x24b/0x380
br_flood+0xc6/0x390
br_dev_xmit+0xa2e/0x12c0
For some reason ebtables rejects blobs that provide entry points that are
not supported by the table, but what it should instead reject is the
opposite: blobs that DO NOT provide an entry point supported by the table.
t->valid_hooks is the bitmask of hooks (input, forward ...) that will see
packets. Providing an entry point that is not support is harmless
(never called/used), but the inverse isn't: it results in a crash
because the ebtables traverser doesn't expect a NULL blob for a location
its receiving packets for.
Instead of fixing all the individual checks, do what iptables is doing and
reject all blobs that differ from the expected hooks.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
When DSA gains support for multiple CPU ports in a LAG, it will become
mandatory to monitor the changeupper events for the DSA master.
In fact, there are already some restrictions to be imposed in that area,
namely that a DSA master cannot be a bridge port except in some special
circumstances.
Centralize the restrictions at the level of the DSA layer as a
preliminary step.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After commit b6c02ef549 ("bridge: Netlink interface fix."),
br_fill_ifinfo() started to send an empty IFLA_AF_SPEC attribute when a
bridge vlan dump is requested but an interface does not have any vlans
configured.
iproute2 ignores such an empty attribute since commit b262a9becbcb
("bridge: Fix output with empty vlan lists") but older iproute2 versions as
well as other utilities have their output changed by the cited kernel
commit, resulting in failed test cases. Regardless, emitting an empty
attribute is pointless and inefficient.
Avoid this change by canceling the attribute if no AF_SPEC data was added.
Fixes: b6c02ef549 ("bridge: Netlink interface fix.")
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20220725001236.95062-1-bpoirier@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Same as the existing ones, no conversions. This is just for sparse sake
only so that we no longer mix be16/u16 and be32/u32 types.
Alternative is to add __force __beX in various places, but this
seems nicer.
objdiff shows no changes.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c
9c5de246c1 ("net: sparx5: mdb add/del handle non-sparx5 devices")
fbb89d02e3 ("net: sparx5: Allow mdb entries to both CPU and ports")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When br_netfilter module is loaded, skbs may be diverted to the
ipv4/ipv6 hooks, just like as if we were routing.
Unfortunately, bridge filter hooks with priority 0 may be skipped
in this case.
Example:
1. an nftables bridge ruleset is loaded, with a prerouting
hook that has priority 0.
2. interface is added to the bridge.
3. no tcp packet is ever seen by the bridge prerouting hook.
4. flush the ruleset
5. load the bridge ruleset again.
6. tcp packets are processed as expected.
After 1) the only registered hook is the bridge prerouting hook, but its
not called yet because the bridge hasn't been brought up yet.
After 2), hook order is:
0 br_nf_pre_routing // br_netfilter internal hook
0 chain bridge f prerouting // nftables bridge ruleset
The packet is diverted to br_nf_pre_routing.
If call-iptables is off, the nftables bridge ruleset is called as expected.
But if its enabled, br_nf_hook_thresh() will skip it because it assumes
that all 0-priority hooks had been called previously in bridge context.
To avoid this, check for the br_nf_pre_routing hook itself, we need to
resume directly after it, even if this hook has a priority of 0.
Unfortunately, this still results in different packet flow.
With this fix, the eval order after in 3) is:
1. br_nf_pre_routing
2. ip(6)tables (if enabled)
3. nftables bridge
but after 5 its the much saner:
1. nftables bridge
2. br_nf_pre_routing
3. ip(6)tables (if enabled)
Unfortunately I don't see a solution here:
It would be possible to move br_nf_pre_routing to a higher priority
so that it will be called later in the pipeline, but this also impacts
ebtables evaluation order, and would still result in this very ordering
problem for all nftables-bridge hooks with the same priority as the
br_nf_pre_routing one.
Searching back through the git history I don't think this has
ever behaved in any other way, hence, no fixes-tag.
Reported-by: Radim Hrazdil <rhrazdil@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Adding mdb entries on disabled ports allows you to do setup before
accepting any traffic, avoiding any time where the port is not in the
multicast group.
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in commit 316580b69d ("u64_stats: provide u64_stats_t type")
we should use u64_stats_t and related accessors to avoid load/store tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Netdev reference helpers have a dev_ prefix for historic
reasons. Renaming the old helpers would be too much churn
but we can rename the tracking ones which are relatively
recent and should be the default for new code.
Rename:
dev_hold_track() -> netdev_hold()
dev_put_track() -> netdev_put()
dev_replace_track() -> netdev_ref_replace()
Link: https://lore.kernel.org/r/20220608043955.919359-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It is possible to stack bridges on top of each other. Consider the
following which makes use of an Ethernet switch:
br1
/ \
/ \
/ \
br0.11 wlan0
|
br0
/ | \
p1 p2 p3
br0 is offloaded to the switch. Above br0 is a vlan interface, for
vlan 11. This vlan interface is then a slave of br1. br1 also has a
wireless interface as a slave. This setup trunks wireless lan traffic
over the copper network inside a VLAN.
A frame received on p1 which is passed up to the bridge has the
skb->offload_fwd_mark flag set to true, indicating that the switch has
dealt with forwarding the frame out ports p2 and p3 as needed. This
flag instructs the software bridge it does not need to pass the frame
back down again. However, the flag is not getting reset when the frame
is passed upwards. As a result br1 sees the flag, wrongly interprets
it, and fails to forward the frame to wlan0.
When passing a frame upwards, clear the flag. This is the Rx
equivalent of br_switchdev_frame_unmark() in br_dev_xmit().
Fixes: f1c2eddf4c ("bridge: switchdev: Use an helper to clear forward mark")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20220518005840.771575-1-andrew@lunn.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add extack support to .ndo_fdb_del in netdevice.h and
all related methods.
Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call the TSO setting helper, GSO is controllable
by user space.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_vlan_group() can return NULL and thus return value must be checked
to avoid dereferencing a NULL pointer.
Fixes: 6284c723d9 ("net: bridge: mst: Notify switchdev drivers of VLAN MSTI migrations")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20220421101247.121896-1-clement.leger@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for fdb flush filtering based on destination ifindex and
vlan id. The ifindex must either match a port's device ifindex or the
bridge's. The vlan support is trivial since it's already validated by
rtnl_fdb_del, we just need to fill it in.
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for fdb flush filtering based on ndm flags and state. NDM
state and flags are mapped to bridge-specific flags and matched
according to the specified masks. NTF_USE is used to represent
added_by_user flag since it sets it on fdb add and we don't have a 1:1
mapping for it. Only allowed bits can be set, NTF_SELF and NTF_MASTER are
ignored.
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to specify exactly which fdbs to be flushed. They are
described by a new structure - net_bridge_fdb_flush_desc. Currently it
can match on port/bridge ifindex, vlan id and fdb flags. It is used to
describe the existing dynamic fdb flush operation. Note that this flush
operation doesn't treat permanent entries in a special way (fdb_delete vs
fdb_delete_local), it will delete them regardless if any port is using
them, so currently it can't directly replace deletes which need to handle
that case, although we can extend it later for that too.
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a minimal ndo_fdb_del_bulk implementation which flushes all entries.
Support for more fine-grained filtering will be added in the following
patches.
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch expands on the earlier work on layer-2 mdb entries by adding
support for host entries. Due to the fact that host joined entries do
not have any flag field, we infer the permanent flag when reporting the
entries to userspace, which otherwise would be listed as 'temp'.
Before patch:
~# bridge mdb add dev br0 port br0 grp 01:00:00:c0:ff:ee permanent
Error: bridge: Flags are not allowed for host groups.
~# bridge mdb add dev br0 port br0 grp 01:00:00:c0:ff:ee
Error: bridge: Only permanent L2 entries allowed.
After patch:
~# bridge mdb add dev br0 port br0 grp 01:00:00:c0:ff:ee permanent
~# bridge mdb show
dev br0 port br0 grp 01:00:00:c0:ff:ee permanent vid 1
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add BR_HAIRPIN_MODE, BR_ISOLATED and BR_MULTICAST_TO_UNICAST port flags to
BR_PORT_FLAGS_HW_OFFLOAD so that switchdev drivers which have an offloaded
data plane have a chance to reject these bridge port flags if they don't
support them yet.
It makes the code path go through the
SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS driver handlers, which return
-EINVAL for everything they don't recognize.
For drivers that don't catch SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS at
all, switchdev will return -EOPNOTSUPP for those which is then ignored, but
those are in the minority.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220410134227.18810-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensure that no bridge masters are ever considered for MST info
dumping. MST states are only supported on bridge ports, not bridge
masters - which br_mst_info_size relies on.
Fixes: 122c29486e ("net: bridge: mst: Support setting and reporting MST port states")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20220322133001.16181-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
its enough to export the meta get reduce helper and then call it
from nft_meta_bridge too.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Output of expressions might be larger than one single register, this might
clobber existing data. Reset tracking for all destination registers that
required to store the expression output.
This patch adds three new helper functions:
- nft_reg_track_update: cancel previous register tracking and update it.
- nft_reg_track_cancel: cancel any previous register tracking info.
- __nft_reg_track_cancel: cancel only one single register tracking info.
Partial register clobbering detection is also supported by checking the
.num_reg field which describes the number of register that are used.
This patch updates the following expressions:
- meta_bridge
- bitwise
- byteorder
- meta
- payload
to use these helper functions.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Skip register tracking for expressions that perform read-only operations
on the registers. Define and use a cookie pointer NFT_REDUCE_READONLY to
avoid defining stubs for these expressions.
This patch re-enables register tracking which was disabled in ed5f85d422
("netfilter: nf_tables: disable register tracking"). Follow up patches
add remaining register tracking for existing expressions.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is useful for switchdev drivers who are offloading MST states
into hardware. As an example, a driver may wish to flush the FDB for a
port when it transitions from forwarding to blocking - which means
that the previous state must be discoverable.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is useful for switchdev drivers that might want to refuse to join
a bridge where MST is enabled, if the hardware can't support it.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
br_mst_get_info answers the question: "On this bridge, which VIDs are
mapped to the given MSTI?"
This is useful in switchdev drivers, which might have to fan-out
operations, relating to an MSTI, per VLAN.
An example: When a port's MST state changes from forwarding to
blocking, a driver may choose to flush the dynamic FDB entries on that
port to get faster reconvergence of the network, but this should only
be done in the VLANs that are managed by the MSTI in question.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Generate a switchdev notification whenever an MST state changes. This
notification is keyed by the VLANs MSTI rather than the VID, since
multiple VLANs may share the same MST instance.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Whenever a VLAN moves to a new MSTI, send a switchdev notification so
that switchdevs can track a bridge's VID to MSTI mappings.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Trigger a switchdev event whenever the bridge's MST mode is
enabled/disabled. This allows constituent ports to either perform any
required hardware config, or refuse the change if it not supported.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make it possible to change the port state in a given MSTI by extending
the bridge port netlink interface (RTM_SETLINK on PF_BRIDGE).The
proposed iproute2 interface would be:
bridge mst set dev <PORT> msti <MSTI> state <STATE>
Current states in all applicable MSTIs can also be dumped via a
corresponding RTM_GETLINK. The proposed iproute interface looks like
this:
$ bridge mst
port msti
vb1 0
state forwarding
100
state disabled
vb2 0
state forwarding
100
state forwarding
The preexisting per-VLAN states are still valid in the MST
mode (although they are read-only), and can be queried as usual if one
is interested in knowing a particular VLAN's state without having to
care about the VID to MSTI mapping (in this example VLAN 20 and 30 are
bound to MSTI 100):
$ bridge -d vlan
port vlan-id
vb1 10
state forwarding mcast_router 1
20
state disabled mcast_router 1
30
state disabled mcast_router 1
40
state forwarding mcast_router 1
vb2 10
state forwarding mcast_router 1
20
state forwarding mcast_router 1
30
state forwarding mcast_router 1
40
state forwarding mcast_router 1
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow a VLAN to move out of the CST (MSTI 0), to an independent tree.
The user manages the VID to MSTI mappings via a global VLAN
setting. The proposed iproute2 interface would be:
bridge vlan global set dev br0 vid <VID> msti <MSTI>
Changing the state in non-zero MSTIs is still not supported, but will
be addressed in upcoming changes.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow the user to switch from the current per-VLAN STP mode to an MST
mode.
Up to this point, per-VLAN STP states where always isolated from each
other. This is in contrast to the MSTP standard (802.1Q-2018, Clause
13.5), where VLANs are grouped into MST instances (MSTIs), and the
state is managed on a per-MSTI level, rather that at the per-VLAN
level.
Perhaps due to the prevalence of the standard, many switching ASICs
are built after the same model. Therefore, add a corresponding MST
mode to the bridge, which we can later add offloading support for in a
straight-forward way.
For now, all VLANs are fixed to MSTI 0, also called the Common
Spanning Tree (CST). That is, all VLANs will follow the port-global
state.
Upcoming changes will make this actually useful by allowing VLANs to
be mapped to arbitrary MSTIs and allow individual MSTI states to be
changed.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
1) Revert CHECKSUM_UNNECESSARY for UDP packet from conntrack.
2) Reject unsupported families when creating tables, from Phil Sutter.
3) GRE support for the flowtable, from Toshiaki Makita.
4) Add GRE offload support for act_ct, also from Toshiaki.
5) Update mlx5 driver to support for GRE flowtable offload,
from Toshiaki Makita.
6) Oneliner to clean up incorrect indentation in nf_conntrack_bridge,
from Jiapeng Chong.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: bridge: clean up some inconsistent indenting
net/mlx5: Support GRE conntrack offload
act_ct: Support GRE offload
netfilter: flowtable: Support GRE
netfilter: nf_tables: Reject tables of unsupported family
Revert "netfilter: conntrack: mark UDP zero checksum as CHECKSUM_UNNECESSARY"
====================
Link: https://lore.kernel.org/r/20220315091513.66544-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, skb->tstamp is reset to 0 whenever the skb is forwarded.
If skb->tstamp has the mono delivery_time, clearing it can hurt
the performance when it finally transmits out to fq@phy-dev.
The earlier patch added a skb->mono_delivery_time bit to
flag the skb->tstamp carrying the mono delivery_time.
This patch adds skb_clear_tstamp() helper which keeps
the mono delivery_time and clears everything else.
The delivery_time clearing will be postponed until the stack knows the
skb will be delivered locally. It will be done in a latter patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->tstamp was first used as the (rcv) timestamp.
The major usage is to report it to the user (e.g. SO_TIMESTAMP).
Later, skb->tstamp is also set as the (future) delivery_time (e.g. EDT in TCP)
during egress and used by the qdisc (e.g. sch_fq) to make decision on when
the skb can be passed to the dev.
Currently, there is no way to tell skb->tstamp having the (rcv) timestamp
or the delivery_time, so it is always reset to 0 whenever forwarded
between egress and ingress.
While it makes sense to always clear the (rcv) timestamp in skb->tstamp
to avoid confusing sch_fq that expects the delivery_time, it is a
performance issue [0] to clear the delivery_time if the skb finally
egress to a fq@phy-dev. For example, when forwarding from egress to
ingress and then finally back to egress:
tcp-sender => veth@netns => veth@hostns => fq@eth0@hostns
^ ^
reset rest
This patch adds one bit skb->mono_delivery_time to flag the skb->tstamp
is storing the mono delivery_time (EDT) instead of the (rcv) timestamp.
The current use case is to keep the TCP mono delivery_time (EDT) and
to be used with sch_fq. A latter patch will also allow tc-bpf@ingress
to read and change the mono delivery_time.
In the future, another bit (e.g. skb->user_delivery_time) can be added
for the SCM_TXTIME where the clock base is tracked by sk->sk_clockid.
[ This patch is a prep work. The following patches will
get the other parts of the stack ready first. Then another patch
after that will finally set the skb->mono_delivery_time. ]
skb_set_delivery_time() function is added. It is used by the tcp_output.c
and during ip[6] fragmentation to assign the delivery_time to
the skb->tstamp and also set the skb->mono_delivery_time.
A note on the change in ip_send_unicast_reply() in ip_output.c.
It is only used by TCP to send reset/ack out of a ctl_sk.
Like the new skb_set_delivery_time(), this patch sets
the skb->mono_delivery_time to 0 for now as a place
holder. It will be enabled in a latter patch.
A similar case in tcp_ipv6 can be done with
skb_set_delivery_time() in tcp_v6_send_response().
[0] (slide 22): https://linuxplumbersconf.org/event/11/contributions/953/attachments/867/1658/LPC_2021_BPF_Datapath_Extensions.pdf
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various switchcores support setting ports in locked mode, so that
clients behind locked ports cannot send traffic through the port
unless a fdb entry is added with the clients MAC address.
Signed-off-by: Hans Schultz <schultz.hans+netdev@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a 802.1X scenario, clients connected to a bridge port shall not
be allowed to have traffic forwarded until fully authenticated.
A static fdb entry of the clients MAC address for the bridge port
unlocks the client and allows bidirectional communication.
This scenario is facilitated with setting the bridge port in locked
mode, which is also supported by various switchcore chipsets.
Signed-off-by: Hans Schultz <schultz.hans+netdev@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cleanup_net() is competing with other rtnl users.
Instead of calling br_net_exit() for each netns,
call br_net_exit_batch() once.
This gives cleanup_net() ability to group more devices
and call unregister_netdevice_many() only once for all bridge devices.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever bridge driver hits the max capacity of MDBs, it disables
the MC processing (by setting corresponding bridge option), but never
notifies switchdev about such change (the notifiers are called only upon
explicit setting of this option, through the registered netlink interface).
This could lead to situation when Software MDB processing gets disabled,
but this event never gets offloaded to the underlying Hardware.
Fix this by adding a notify message in such case.
Fixes: 147c1e9b90 ("switchdev: bridge: Offload multicast disabled")
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20220215165303.31908-1-oleksandr.mazur@plvision.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The major user of replayed switchdev objects is DSA, and so far it
hasn't needed information about anything other than bridge port VLANs,
so this is all that br_switchdev_vlan_replay() knows to handle.
DSA has managed to get by through replicating every VLAN addition on a
user port such that the same VLAN is also added on all DSA and CPU
ports, but there is a corner case where this does not work.
The mv88e6xxx DSA driver currently prints this error message as soon as
the first port of a switch joins a bridge:
mv88e6085 0x0000000008b96000:00: port 0 failed to add a6:ef:77:c8:5f:3d vid 1 to fdb: -95
where a6:ef:77:c8:5f:3d vid 1 is a local FDB entry corresponding to the
bridge MAC address in the default_pvid.
The -EOPNOTSUPP is returned by mv88e6xxx_port_db_load_purge() because it
tries to map VID 1 to a FID (the ATU is indexed by FID not VID), but
fails to do so. This is because ->port_fdb_add() is called before
->port_vlan_add() for VID 1.
The abridged timeline of the calls is:
br_add_if
-> netdev_master_upper_dev_link
-> dsa_port_bridge_join
-> switchdev_bridge_port_offload
-> br_switchdev_vlan_replay (*)
-> br_switchdev_fdb_replay
-> mv88e6xxx_port_fdb_add
-> nbp_vlan_init
-> nbp_vlan_add
-> mv88e6xxx_port_vlan_add
and the issue is that at the time of (*), the bridge port isn't in VID 1
(nbp_vlan_init hasn't been called), therefore br_switchdev_vlan_replay()
won't have anything to replay, therefore VID 1 won't be in the VTU by
the time mv88e6xxx_port_fdb_add() is called.
This happens only when the first port of a switch joins. For further
ports, the initial mv88e6xxx_port_vlan_add() is sufficient for VID 1 to
be loaded in the VTU (which is switch-wide, not per port).
The problem is somewhat unique to mv88e6xxx by chance, because most
other drivers offload an FDB entry by VID, so FDBs and VLANs can be
added asynchronously with respect to each other, but addressing the
issue at the bridge layer makes sense, since what mv88e6xxx requires
isn't absurd.
To fix this problem, we need to recognize that it isn't the VLAN group
of the port that we're interested in, but the VLAN group of the bridge
itself (so it isn't a timing issue, but rather insufficient information
being passed from switchdev to drivers).
As mentioned, currently nbp_switchdev_sync_objs() only calls
br_switchdev_vlan_replay() for VLANs corresponding to the port, but the
VLANs corresponding to the bridge itself, for local termination, also
need to be replayed. In this case, VID 1 is not (yet) present in the
port's VLAN group but is present in the bridge's VLAN group.
So to fix this bug, DSA is now obligated to explicitly handle VLANs
pointing towards the bridge in order to "close this race" (which isn't
really a race). As Tobias Waldekranz notices, this also implies that it
must explicitly handle port VLANs on foreign interfaces, something that
worked implicitly before:
https://patchwork.kernel.org/project/netdevbpf/patch/20220209213044.2353153-6-vladimir.oltean@nxp.com/#24735260
So in the end, br_switchdev_vlan_replay() must replay all VLANs from all
VLAN groups: all the ports, and the bridge itself.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There may be switchdev drivers that can add/remove a FDB or MDB entry
only as long as the VLAN it's in has been notified and offloaded first.
The nbp_switchdev_sync_objs() method satisfies this requirement on
addition, but nbp_switchdev_unsync_objs() first deletes VLANs, then
deletes MDBs and FDBs. Reverse the order of the function calls to cater
to this requirement.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_switchdev_port_vlan_add() currently emits a SWITCHDEV_PORT_OBJ_ADD
event with a SWITCHDEV_OBJ_ID_PORT_VLAN for 2 distinct cases:
- a struct net_bridge_vlan got created
- an existing struct net_bridge_vlan was modified
This makes it impossible for switchdev drivers to properly balance
PORT_OBJ_ADD with PORT_OBJ_DEL events, so if we want to allow that to
happen, we must provide a way for drivers to distinguish between a
VLAN with changed flags and a new one.
Annotate struct switchdev_obj_port_vlan with a "bool changed" that
distinguishes the 2 cases above.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when a VLAN entry is added multiple times in a row to a
bridge port, nbp_vlan_add() calls br_switchdev_port_vlan_add() each
time, even if the VLAN already exists and nothing about it has changed:
bridge vlan add dev lan12 vid 100 master static
Similarly, when a VLAN is added multiple times in a row to a bridge,
br_vlan_add_existing() doesn't filter at all the calls to
br_switchdev_port_vlan_add():
bridge vlan add dev br0 vid 100 self
This behavior makes driver-level accounting of VLANs impossible, since
it is enough for a single deletion event to remove a VLAN, but the
addition event can be emitted an unlimited number of times.
The cause for this can be identified as follows: we rely on
__vlan_add_flags() to retroactively tell us whether it has changed
anything about the VLAN flags or VLAN group pvid. So we'd first have to
call __vlan_add_flags() before calling br_switchdev_port_vlan_add(), in
order to have access to the "bool *changed" information. But we don't
want to change the event ordering, because we'd have to revert the
struct net_bridge_vlan changes we've made if switchdev returns an error.
So to solve this, we need another function that tells us whether any
change is going to occur in the VLAN or VLAN group, _prior_ to calling
__vlan_add_flags().
Split __vlan_add_flags() into a precommit and a commit stage, and rename
it to __vlan_flags_update(). The precommit stage,
__vlan_flags_would_change(), will determine whether there is any reason
to notify switchdev due to a change of flags (note: the BRENTRY flag
transition from false to true is treated separately: as a new switchdev
entry, because we skipped notifying the master VLAN when it wasn't a
brentry yet, and therefore not as a change of flags).
With this lookahead/precommit function in place, we can avoid notifying
switchdev if nothing changed for the VLAN and VLAN group.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is a very subtle aspect to the behavior of
__vlan_add_flags(): it changes the struct net_bridge_vlan flags and
pvid, yet it returns true ("changed") even if none of those changed,
just a transition of br_vlan_is_brentry(v) took place from false to
true.
This can be seen in br_vlan_add_existing(), however we do not actually
rely on this subtle behavior, since the "if" condition that checks that
the vlan wasn't a brentry before had a useless (until now) assignment:
*changed = true;
Make things more obvious by actually making __vlan_add_flags() do what's
written on the box, and be more specific about what is actually written
on the box. This is needed because further transformations will be done
to __vlan_add_flags().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN is added to a bridge port and it doesn't exist on the bridge
device yet, it gets created for the multicast context, but it is
'hidden', since it doesn't have the BRENTRY flag yet:
ip link add br0 type bridge && ip link set swp0 master br0
bridge vlan add dev swp0 vid 100 # the master VLAN 100 gets created
bridge vlan add dev br0 vid 100 self # that VLAN becomes brentry just now
All switchdev drivers ignore switchdev notifiers for VLAN entries which
have the BRENTRY unset, and for good reason: these are merely private
data structures used by the bridge driver. So we might just as well not
notify those at all.
Cleanup in the switchdev drivers that check for the BRENTRY flag is now
possible, and will be handled separately, since those checks just became
dead code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN is added to a bridge port, a master VLAN gets created on the
bridge for context, but it doesn't have the BRENTRY flag.
Then, when the same VLAN is added to the bridge itself, that enters
through the br_vlan_add_existing() code path and gains the BRENTRY flag,
thus it becomes "existing".
It seems natural to check for this condition early, because the current
code flow is to notify switchdev of the addition of a VLAN that isn't a
brentry, just to delete it immediately afterwards.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the following call path returns an error from switchdev:
nbp_vlan_flush
-> __vlan_del
-> __vlan_vid_del
-> br_switchdev_port_vlan_del
-> __vlan_group_free
-> WARN_ON(!list_empty(&vg->vlan_list));
then the deletion of the net_bridge_vlan is silently halted, which will
trigger the WARN_ON from __vlan_group_free().
The WARN_ON is rather unhelpful, because nothing about the source of the
error is printed. Add a print to catch errors from __vlan_del.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Remove leftovers from flowtable modules, from Geert Uytterhoeven.
2) Missing refcount increment of conntrack template in nft_ct,
from Florian Westphal.
3) Reduce nft_zone selftest time, also from Florian.
4) Add selftest to cover stateless NAT on fragments, from Florian Westphal.
5) Do not set net_device when for reject packets from the bridge path,
from Phil Sutter.
6) Cancel register tracking info on nft_byteorder operations.
7) Extend nft_concat_range selftest to cover set reload with no elements,
from Florian Westphal.
8) Remove useless update of pointer in chain blob builder, reported
by kbuild test robot.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: nf_tables: remove assignment with no effect in chain blob builder
selftests: nft_concat_range: add test for reload with no element add/del
netfilter: nft_byteorder: track register operations
netfilter: nft_reject_bridge: Fix for missing reply from prerouting
selftests: netfilter: check stateless nat udp checksum fixup
selftests: netfilter: reduce zone stress test running time
netfilter: nft_ct: fix use after free when attaching zone template
netfilter: Remove flowtable relics
====================
Link: https://lore.kernel.org/r/20220127235235.656931-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When using per-vlan state, if vlan snooping and stats are disabled,
untagged or priority-tagged ingress frame will go to check pvid state.
If the port state is forwarding and the pvid state is not
learning/forwarding, untagged or priority-tagged frame will be dropped
but skb memory is not freed.
Should free skb when __allowed_ingress returns false.
Fixes: a580c76d53 ("net: bridge: vlan: add per-vlan state")
Signed-off-by: Tim Yi <tim.yi@pica8.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20220127074953.12632-1-tim.yi@pica8.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When dumping vlan options for a single net device we send the same
entries infinitely because user-space expects a 0 return at the end but
we keep returning skb->len and restarting the dump on retry. Fix it by
returning the value from br_vlan_dump_dev() if it completed or there was
an error. The only case that must return skb->len is when the dump was
incomplete and needs to continue (-EMSGSIZE).
Reported-by: Benjamin Poirier <bpoirier@nvidia.com>
Fixes: 8dcea18708 ("net: bridge: vlan: add rtm definitions and dump support")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to commit fa538f7cf0 ("netfilter: nf_reject: add reject skbuff
creation helpers"), nft_reject_bridge did not assign to nskb->dev before
passing nskb on to br_forward(). The shared skbuff creation helpers
introduced in above commit do which seems to confuse br_forward() as
reject statements in prerouting hook won't emit a packet anymore.
Fix this by simply passing NULL instead of 'dev' to the helpers - they
use the pointer for just that assignment, nothing else.
Fixes: fa538f7cf0 ("netfilter: nf_reject: add reject skbuff creation helpers")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
I left one dev_put() in br_add_if() error path and sure enough
syzbot found its way.
As the tracker is allocated in new_nbp(), we must make sure
to properly free it.
We have to call dev_put_track(dev, &p->dev_tracker) before
@p object is freed, of course. This is not an issue because
br_add_if() owns a reference on @dev.
Fixes: b2dcdc7f73 ("net: bridge: add net device refcount tracker")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next. This
includes one patch to update ovs and act_ct to use nf_ct_put() instead
of nf_conntrack_put().
1) Add netns_tracker to nfnetlink_log and masquerade, from Eric Dumazet.
2) Remove redundant rcu read-size lock in nf_tables packet path.
3) Replace BUG() by WARN_ON_ONCE() in nft_payload.
4) Consolidate rule verdict tracing.
5) Replace WARN_ON() by WARN_ON_ONCE() in nf_tables core.
6) Make counter support built-in in nf_tables.
7) Add new field to conntrack object to identify locally generated
traffic, from Florian Westphal.
8) Prevent NAT from shadowing well-known ports, from Florian Westphal.
9) Merge nf_flow_table_{ipv4,ipv6} into nf_flow_table_inet, also from
Florian.
10) Remove redundant pointer in nft_pipapo AVX2 support, from Colin Ian King.
11) Replace opencoded max() in conntrack, from Jiapeng Chong.
12) Update conntrack to use refcount_t API, from Florian Westphal.
13) Move ip_ct_attach indirection into the nf_ct_hook structure.
14) Constify several pointer object in the netfilter codebase,
from Florian Westphal.
15) Tree-wide replacement of nf_conntrack_put() by nf_ct_put(), also
from Florian.
16) Fix egress splat due to incorrect rcu notation, from Florian.
17) Move stateful fields of connlimit, last, quota, numgen and limit
out of the expression data area.
18) Build a blob to represent the ruleset in nf_tables, this is a
requirement of the new register tracking infrastructure.
19) Add NFT_REG32_NUM to define the maximum number of 32-bit registers.
20) Add register tracking infrastructure to skip redundant
store-to-register operations, this includes support for payload,
meta and bitwise expresssions.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next: (32 commits)
netfilter: nft_meta: cancel register tracking after meta update
netfilter: nft_payload: cancel register tracking after payload update
netfilter: nft_bitwise: track register operations
netfilter: nft_meta: track register operations
netfilter: nft_payload: track register operations
netfilter: nf_tables: add register tracking infrastructure
netfilter: nf_tables: add NFT_REG32_NUM
netfilter: nf_tables: add rule blob layout
netfilter: nft_limit: move stateful fields out of expression data
netfilter: nft_limit: rename stateful structure
netfilter: nft_numgen: move stateful fields out of expression data
netfilter: nft_quota: move stateful fields out of expression data
netfilter: nft_last: move stateful fields out of expression data
netfilter: nft_connlimit: move stateful fields out of expression data
netfilter: egress: avoid a lockdep splat
net: prefer nf_ct_put instead of nf_conntrack_put
netfilter: conntrack: avoid useless indirection during conntrack destruction
netfilter: make function op structures const
netfilter: core: move ip_ct_attach indirection to struct nf_ct_hook
netfilter: conntrack: convert to refcount_t api
...
====================
Link: https://lore.kernel.org/r/20220109231640.104123-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The meta expression might mangle the packet metadata, cancel register
tracking since any metadata in the registers is stale.
Finer grain register tracking cancellation by inspecting the meta type
on the register is also possible.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
commit 077cdda764 ("net/mlx5e: TC, Fix memory leak with rules with internal port")
commit 31108d142f ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
commit 4390c6edc0 ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
https://lore.kernel.org/all/20211229065352.30178-1-saeed@kernel.org/
net/smc/smc_wr.c
commit 49dc9013e3 ("net/smc: Use the bitmap API when applicable")
commit 349d43127d ("net/smc: fix kernel panic caused by race of smc_sock")
bitmap_zero()/memset() is removed by the fix
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We need to first check if the context is a vlan one, then we need to
check the global bridge multicast vlan snooping flag, and finally the
vlan's multicast flag, otherwise we will unnecessarily enable vlan mcast
processing (e.g. querier timers).
Fixes: 7b54aaaf53 ("net: bridge: multicast: add vlan state initialization and control")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20211228153142.536969-1-nikolay@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As reported[1] if startup query interval is set too low in combination with
large number of startup queries and we have multiple bridges or even a
single bridge with multiple querier vlans configured we can crash the
machine. Add a 1 second minimum which must be enforced by overwriting the
value if set lower (i.e. without returning an error) to avoid breaking
user-space. If that happens a log message is emitted to let the admin know
that the startup interval has been set to the minimum. It doesn't make
sense to make the startup interval lower than the normal query interval
so use the same value of 1 second. The issue has been present since these
intervals could be user-controlled.
[1] https://lore.kernel.org/netdev/e8b9ce41-57b9-b6e2-a46a-ff9c791cf0ba@gmail.com/
Fixes: d902eee43f ("bridge: Add multicast count/interval sysfs entries")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As reported[1] if query interval is set too low and we have multiple
bridges or even a single bridge with multiple querier vlans configured
we can crash the machine. Add a 1 second minimum which must be enforced
by overwriting the value if set lower (i.e. without returning an error) to
avoid breaking user-space. If that happens a log message is emitted to let
the administrator know that the interval has been set to the minimum.
The issue has been present since these intervals could be user-controlled.
[1] https://lore.kernel.org/netdev/e8b9ce41-57b9-b6e2-a46a-ff9c791cf0ba@gmail.com/
Fixes: d902eee43f ("bridge: Add multicast count/interval sysfs entries")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sock.h is pretty heavily used (5k objects rebuilt on x86 after
it's touched). We can drop the include of filter.h from it and
add a forward declaration of struct sk_filter instead.
This decreases the number of rebuilt objects when bpf.h
is touched from ~5k to ~1k.
There's a lot of missing includes this was masking. Primarily
in networking tho, this time.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/bpf/20211229004913.513372-1-kuba@kernel.org
In compat mode SIOC{G,S}IFBR ioctls were only supporting
BRCTL_GET_VERSION returning an artificially version to spur userland
tool to use SIOCDEVPRIVATE instead. But some userland tools ignore that
and use SIOC{G,S}IFBR unconditionally as seen with busybox's brctl.
Example of non working 32-bit brctl with CONFIG_COMPAT=y:
$ brctl show
brctl: SIOCGIFBR: Invalid argument
Example of fixed 32-bit brctl with CONFIG_COMPAT=y:
$ brctl show
bridge name bridge id STP enabled interfaces
br0
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Co-developed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 561d835281 ("bridge: use ndo_siocdevprivate") changed the
source and destination arguments of copy_{to,from}_user in bridge's
old_deviceless() from args[1] to uarg breaking SIOC{G,S}IFBR ioctls.
Commit cbd7ad29a5 ("net: bridge: fix ioctl old_deviceless bridge
argument") fixed only BRCTL_{ADD,DEL}_BRIDGES commands leaving
BRCTL_GET_BRIDGES one untouched.
The fixes BRCTL_GET_BRIDGES as well and has been tested with busybox's
brctl.
Example of broken brctl:
$ brctl show
bridge name bridge id STP enabled interfaces
brctl: can't get bridge name for index 0: No such device or address
Example of fixed brctl:
$ brctl show
bridge name bridge id STP enabled interfaces
br0 8000.000000000000 no
Fixes: 561d835281 ("bridge: use ndo_siocdevprivate")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/all/20211223153139.7661-2-repk@triplefau.lt/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next, mostly
rather small housekeeping patches:
1) Remove unused variable in IPVS, from GuoYong Zheng.
2) Use memset_after in conntrack, from Kees Cook.
3) Remove leftover function in nfnetlink_queue, from Florian Westphal.
4) Remove redundant test on bool in conntrack, from Bernard Zhao.
5) egress support for nft_fwd, from Lukas Wunner.
6) Make pppoe work for br_netfilter, from Florian Westphal.
7) Remove unused variable in conntrack resize routine, from luo penghao.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next:
netfilter: conntrack: Remove useless assignment statements
netfilter: bridge: add support for pppoe filtering
netfilter: nft_fwd_netdev: Support egress hook
netfilter: ctnetlink: remove useless type conversion to bool
netfilter: nf_queue: remove leftover synchronize_rcu
netfilter: conntrack: Use memset_startat() to zero struct nf_conn
ipvs: remove unused variable for ip_vs_new_dest
====================
Link: https://lore.kernel.org/r/20211215234911.170741-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This makes 'bridge-nf-filter-pppoe-tagged' sysctl work for
bridged traffic.
Looking at the original commit it doesn't appear this ever worked:
static unsigned int br_nf_post_routing(unsigned int hook, struct sk_buff **pskb,
[..]
if (skb->protocol == htons(ETH_P_8021Q)) {
skb_pull(skb, VLAN_HLEN);
skb->network_header += VLAN_HLEN;
+ } else if (skb->protocol == htons(ETH_P_PPP_SES)) {
+ skb_pull(skb, PPPOE_SES_HLEN);
+ skb->network_header += PPPOE_SES_HLEN;
}
[..]
NF_HOOK(... POST_ROUTING, ...)
... but the adjusted offsets are never restored.
The alternative would be to rip this code out for good,
but otoh we'd have to keep this anyway for the vlan handling
(which works because vlan tag info is in the skb, not the packet
payload).
Reported-and-tested-by: Amish Chana <amish@3g.co.za>
Fixes: 516299d2f5 ("[NETFILTER]: bridge-nf: filter bridged IPv4/IPv6 encapsulated in pppoe traffic")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
