When programming the start of a periodic output, the code wrongly places
the seconds value into the "low" register and the nanoseconds into the
"high" register. Even though this is backwards, it slipped through my
testing, because the re-arming code in the interrupt service routine is
correct, and the signal does appear starting with the second edge.
This patch fixes the issue by programming the registers correctly.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not check the return value of enic_dev_stats_dump(). If allocation
fails, we will hit NULL pointer reference.
Return only if memory allocation fails. For other failures, we return the
previously recorded values.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RGMII block is currently only powered on when using RGMII or
RGMII_NO_ID, which is not correct when using the GENET interface in MII
or Reverse MII modes. We always need to power on the RGMII interface for
this block to properly work, regardless of the MII mode in which we
operate.
Fixes: aa09677cba ("net: bcmgenet: add MDIO routines")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver gets unregistered a call to netif_napi_del() was
missing, this all was also missing in the error paths of
b44_init_one().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several places in the driver (all in control paths) where
coherent dma memory is being allocated using either dma_alloc_coherent()
or the deprecated pci_alloc_consistent(). All these calls should be
changed to use dma_zalloc_coherent() to avoid uninitialized fields in
data structures backed by this memory.
Reported-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the Tx timer function runs in softirq context the driver needs
to call disable_irq_nosync instead of a disable_irq.
Reported-by: Josh Stone <jistone@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SRIOV is enabled we need to be in VEB mode not VEPA mode at probe.
This fixes an NPAR bug when SRIOV is enabled in the BIOS.
Change-ID: Ibf006abafd9a0ca3698ec24848cd771cf345cbbc
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The patch fixes a bug in the default configuration which
prevented a software bridge loaded on the PF interface from
working correctly because broadcast packets are incorrectly
looped back.
Fix the general case, by loading the driver in VEPA mode Until a
VF or VMDq VSI is added. This way loopback on the Main VSI is
turned off until needed and can resolve the issue of unnecessary
reflection for users that do not have VF or VMDq VSIs setup.
The driver must now coordinate the loopback setting for the Flow
Director (FDIR) VSI to make sure it is in sync with the current
VEB or VEPA mode setting.
The user can still switch bridge modes from the bridge commands and
choose to be in VEPA mode with VF VSIs. Because of hardware
requirements, the call to switch to VEB mode when no VF/VMDqs are
present will be rejected.
NOTE: This patch uses BIT_ULL as that is preferred going forward,
a followup patch in the lower priority queue to net-next will fix
up the remaining 1 << usages.
Change-ID: Ib121ddb18fe4b3c4f52e9deda6fcbeb9105683d1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking fixes from David Miller:
1) Various VTI tunnel (mark handling, PMTU) bug fixes from Alexander
Duyck and Steffen Klassert.
2) Revert ethtool PHY query change, it wasn't correct. The PHY address
selected by the driver running the PHY to MAC connection decides
what PHY address GET ethtool operations return information from.
3) Fix handling of sequence number bits for encryption IV generation in
ESP driver, from Herbert Xu.
4) UDP can return -EAGAIN when we hit a bad checksum on receive, even
when there are other packets in the receive queue which is wrong.
Just respect the error returned from the generic socket recv
datagram helper. From Eric Dumazet.
5) Fix BNA driver firmware loading on big-endian systems, from Ivan
Vecera.
6) Fix regression in that we were inheriting the congestion control of
the listening socket for new connections, the intended behavior
always was to use the default in this case. From Neal Cardwell.
7) Fix NULL deref in brcmfmac driver, from Arend van Spriel.
8) OTP parsing fix in iwlwifi from Liad Kaufman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
vti6: Add pmtu handling to vti6_xmit.
Revert "net: core: 'ethtool' issue with querying phy settings"
bnx2x: Move statistics implementation into semaphores
xen: netback: read hotplug script once at start of day.
xen: netback: fix printf format string warning
Revert "netfilter: ensure number of counters is >0 in do_replace()"
net: dsa: Properly propagate errors from dsa_switch_setup_one
tcp: fix child sockets to use system default congestion control if not set
udp: fix behavior of wrong checksums
sfc: free multiple Rx buffers when required
bna: fix soft lock-up during firmware initialization failure
bna: remove unreasonable iocpf timer start
bna: fix firmware loading on big-endian machines
bridge: fix br_multicast_query_expired() bug
via-rhine: Resigning as maintainer
brcmfmac: avoid null pointer access when brcmf_msgbuf_get_pktid() fails
mac80211: Fix mac80211.h docbook comments
iwlwifi: nvm: fix otp parsing in 8000 hw family
iwlwifi: pcie: fix tracking of cmd_in_flight
ip_vti/ip6_vti: Preserve skb->mark after rcv_cb call
...
Commit dff173de84 ("bnx2x: Fix statistics locking scheme") changed the
bnx2x locking around statistics state into using a mutex - but the lock
is being accessed via a timer which is forbidden.
[If compiled with CONFIG_DEBUG_MUTEXES, logs show a warning about
accessing the mutex in interrupt context]
This moves the implementation into using a semaphore [with size '1']
instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we come to tear things down in netback_remove() and generate the
uevent it is possible that the xenstore directory has already been
removed (details below).
In such cases netback_uevent() won't be able to read the hotplug
script and will write a xenstore error node.
A recent change to the hypervisor exposed this race such that we now
sometimes lose it (where apparently we didn't ever before).
Instead read the hotplug script configuration during setup and use it
for the lifetime of the backend device.
The apparently more obvious fix of moving the transition to
state=Closed in netback_remove() to after the uevent does not work
because it is possible that we are already in state=Closed (in
reaction to the guest having disconnected as it shutdown). Being
already in Closed means the toolstack is at liberty to start tearing
down the xenstore directories. In principal it might be possible to
arrange to unregister the device sooner (e.g on transition to Closing)
such that xenstore would still be there but this state machine is
fragile and prone to anger...
A modern Xen system only relies on the hotplug uevent for driver
domains, when the backend is in the same domain as the toolstack it
will run the necessary setup/teardown directly in the correct sequence
wrt xenstore changes.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/xen-netback/netback.c: In function ‘xenvif_tx_build_gops’:
drivers/net/xen-netback/netback.c:1253:8: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 5 has type ‘int’ [-Wformat=]
(txreq.offset&~PAGE_MASK) + txreq.size);
^
PAGE_MASK's type can vary by arch, so a cast is needed.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
----
v2: Cast to unsigned long, since PAGE_MASK can vary by arch.
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Rx packet data must be dropped, all the buffers
associated with that Rx packet must be freed. Extend
and rename efx_free_rx_buffer() to efx_free_rx_buffers()
and loop through all the fragments.
By doing so this patch fixes a possible memory leak.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug in the driver initialization causes soft-lockup if firmware
initialization timeout is reached. Polling function bfa_ioc_poll_fwinit()
incorrectly calls bfa_nw_iocpf_timeout() when the timeout is reached.
The problem is that bfa_nw_iocpf_timeout() calls again
bfa_ioc_poll_fwinit()... etc. The bfa_ioc_poll_fwinit() should directly
send timeout event for iocpf and the same should be done if firmware
download into HW fails.
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver starts iocpf timer prior bnad_ioceth_enable() call and this is
unreasonable. This piece of code probably originates from Brocade/Qlogic
out-of-box driver during initial import into upstream. This driver uses
only one timer and queue to implement multiple timers and this timer is
started at this place. The upstream driver uses multiple timers instead
of this.
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware required by bna is stored in appropriate files as sequence
of LE32 integers. After loading by request_firmware() they need to be
byte-swapped on big-endian arches. Without this conversion the NIC
is unusable on big-endian machines.
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two fixes which got lost in my recent distraction. One is a weird
cpumask function which needed to be rewritten, the other is a module
bug which is cc:stable.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVaBENAAoJENkgDmzRrbjxxL4QAJMFwo21VN8rwIsEJ2P/Yh4u
YXxJtnbrSPZtyad8J4G6FGOOfM7ImkkADhGJE8MN05goIFmeORWduAiozBtZBfo3
OVpeo0HIGTEMXq/QCxSQsDhP9MSeWV592vjhlqQJ2KhU9Gpstc/Ub9ArVWuY3FD3
CFN6ciw+5DIhoc6jMI2P9XX7jpR4VOBu320j+3lQ1QZ1aEZIaPefWH+VYuIZXirq
E6N4yKgTahKb1Clr0DS6EB2Z5g+upNzFf4WBHaChP5EklwatZkHAOvzfSLWcbShI
ochGV5LBPcn7ruqOD5mR4LGkxfQSYPCKCKihmenD/EVoO/dshKOQREfsqRXNsh5X
xk4yx/VCy68ubIjx7FIDL18qDvJrX82+Z2bYZbENvKrVinaQ7MWB+CokK0fNW0ai
ZMP5s32vSUZMMIIE7+fS4n3BLUxOpLZC8S0wIac19jNKzCHVTuhnUolCHk11zQLk
IIDHEJwzvWtPjKOyUyd7HG0bYeczwf8DZgHg+xom9BNbHbK3Jk5d1Sibjgf8eGg+
O36XR8FYYvqHwqqrPKSSaWoLj578/IWyHZg/V4tQ2HWi189BVHk6Iw2knftsvvPw
pBu2AdbRSLLD+X/pwrdmm+xgytjUIr1X/Qnwj/eE5MvB/vaVVwV0OjapU/Z6S+dL
JrZGvbWcviyjpvGD+vG1
=wuP+
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull fixes for cpumask and modules from Rusty Russell:
"** NOW WITH TESTING! **
Two fixes which got lost in my recent distraction. One is a weird
cpumask function which needed to be rewritten, the other is a module
bug which is cc:stable"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
cpumask_set_cpu_local_first => cpumask_local_spread, lament
module: Call module notifier on failure after complete_formation()
The radio cfg DWORD was taken from the wrong place in the
8000 HW family, after a line in the code was wrongly changed
by mistake. This broke several 8260 devices.
Fixes: 5dd9c68a85 ("iwlwifi: drop support for early versions of 8000")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The cmd_in_flight tracking was introduced to workaround faulty
power management hardware, by having the driver keep the NIC
awake as long as there are commands in flight. However, some of
the code handling this workaround was unconditionally executed,
which resulted with an inconsistent state where the driver assumed
that the NIC was awake although it wasn't.
Fix this by renaming 'cmd_in_flight' to 'cmd_hold_nic_awake' and
handling the NIC requested awake state only for hardwares for
which the workaround is needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
da91309e0a (cpumask: Utility function to set n'th cpu...) created a
genuinely weird function. I never saw it before, it went through DaveM.
(He only does this to make us other maintainers feel better about our own
mistakes.)
cpumask_set_cpu_local_first's purpose is say "I need to spread things
across N online cpus, choose the ones on this numa node first"; you call
it in a loop.
It can fail. One of the two callers ignores this, the other aborts and
fails the device open.
It can fail in two ways: allocating the off-stack cpumask, or through a
convoluted codepath which AFAICT can only occur if cpu_online_mask
changes. Which shouldn't happen, because if cpu_online_mask can change
while you call this, it could return a now-offline cpu anyway.
It contains a nonsensical test "!cpumask_of_node(numa_node)". This was
drawn to my attention by Geert, who said this causes a warning on Sparc.
It sets a single bit in a cpumask instead of returning a cpu number,
because that's what the callers want.
It could be made more efficient by passing the previous cpu rather than
an index, but that would be more invasive to the callers.
Fixes: da91309e0a
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (then rebased)
Tested-by: Amir Vadai <amirv@mellanox.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Acked-by: David S. Miller <davem@davemloft.net>
xennet_remove() freed the queues before freeing the netdevice which
results in a use-after-free when free_netdev() tries to delete the
napi instances that have already been freed.
Fix this by fully destroy the queues (which includes deleting the napi
instances) before freeing the netdevice.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test in mlx4_load_one() to remove MLX4_FLAG_MSI_X expects mlx4_NOP() to
fail with -EBUSY. It is also necessary to avoid the reset since the device
is not fully reinitialized before calling mlx4_start_hca() a second time.
Note that this will also affect mlx4_test_interrupts(), the only other user
of MLX4_CMD_NOP.
Fixes: f5aef5a ("net/mlx4_core: Activate reset flow upon fatal command cases")
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e9ce7cb6b1 ("xen-netback: Factor queue-specific data into queue
struct") introduced a regression when moving queue-specific data into
the queue struct by failing to set the credit_bytes field. This
prevented bandwidth limiting from working. Initialize the field as it
was done before multiqueue support was added.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If read() syscall requests unexpected number of bytes from "dimm" binary
attribute file, return EINVAL instead of EPERM.
At the same time pin down sysfs file size to the fixed
sizeof(struct netxen_dimm_cfg), which allows to exploit some missing
sanity checks from kernfs (file boundary checks vs offset etc.)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ethtool command is used to set the speed of the device while
the device is down, the check to set the initial mode may fail when
the device is brought up, causing failure to bring the device up.
Update the code to set the initial mode based on the desired speed if
auto-negotiation is disabled.
This patch fixes a bug introduced by:
d9663c8c21 ("amd-xgbe-phy: Use phydev advertising field vs supported")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pair of nested spin locks was introduced in commit 63502b8d0
"dp83640: Fix receive timestamp race condition".
Unfortunately the 'flags' parameter was reused for the inner lock,
clobbering the originally saved IRQ state. This patch fixes the issue
by changing the inner lock to plain spin_lock without irqsave.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of the ext_write function are supposed to hold a mutex that
protects the state of the dialed page, but one caller was missing the
lock from the very start, and over time the code has been changed
without following the rule. This patch cleans up the call sites in
violation of the rule.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the calibration function that corrects the initial offsets
among multiple devices only works the first time. If the function is
called more than once, the calibration fails and bogus offsets will be
programmed into the devices.
In a well hidden spot, the device documentation tells that trigger indexes
0 and 1 are special in allowing the TRIG_IF_LATE flag to actually work.
This patch fixes the issue by using one of the special triggers during the
recalibration method.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac DebugFS entries are currently global to the driver. As a result,
having more than one stmmac device in the system creates the following
error:
* ERROR stmmaceth, debugfs create directory failed
* stmmac_hw_setup: failed debugFS registration
This also results in being able to access the debugfs information for
the first registered device only.
This patch changes the debugfs structure to have one sub-directory per
net-device. Files under "/sys/kernel/debug/stmmaceth" will now show-up
under /sys/kernel/debug/stmmaceth/ethN/.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix in send of emac regs dump to ethtool which
causing in wrong data interpretation on ethtool
layer for MII and EMAC.
Signed-off-by: Ivan Mikhaylov <ivan@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix firmware name and other things to enable 3165
* fix bad APMG configuration for 8000 (no AMPG on these devices)
* fix MAC address assignment for 8000
* fix firmware debugging triggers (MLME)
* fix several bugs in low power states code (net-detect, d0i3)
ssb:
* fix reboot after device reset for WRT350N v1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVYwxHAAoJEG4XJFUm622bBTwH/RH0Yx5MBK+sD4d16i70d5nh
dbE0wSBy9ZOT6cMVkAqViZg9T+EQ61+Lre7hwNNM6l/NLkTyjyEXB0Not9ERfLc/
E1g4BBHUfg9LUrbufIgWcTZRLewMk7lOBDN22hIcaVYAM6m9QFNwK+qnkFSXNkCq
Pc0aRDWEYHrVvx8A/XYjInrb/oJqT6z7t83lWHbgtJGmCAVsEaqSvdn2badpecHi
xar7PrdvYkXzFyd7xxmXPcvwkiAzKdIDdF3WR+SuS/V7Tk+2Cw5yrBWrIKc3QqtA
+DfIY3Xa9zHHr1SLvoOQ0VooWTsY+RhSdmEbilG0KFOgNnJz3Zm5Abr2mzkvqvA=
=05aZ
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2015-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi:
* fix firmware name and other things to enable 3165
* fix bad APMG configuration for 8000 (no AMPG on these devices)
* fix MAC address assignment for 8000
* fix firmware debugging triggers (MLME)
* fix several bugs in low power states code (net-detect, d0i3)
ssb:
* fix reboot after device reset for WRT350N v1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding support for 7425 PHY in the 7xxx PHY driver, the ID that
was used was actually coming from an external PHY: a BCM5461x. Fix this
by using the proper ID for the internal 7425 PHY and set the
PHY_IS_INTERNAL flag, otherwise consumers of this PHY driver would not
be able to properly identify it as such.
Fixes: d068b02cfd ("net: phy: add BCM7425 and BCM7429 PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the Zynq TRM, gigabit half duplex is not supported. Add a
new cap and compatible string so Zynq can avoid advertising that mode.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_curr_frame_payload field is u32. When we try to calculate a
small negative delta based on it, we end up with a positive integer
close to 2^32 instead. So the tx_bytes pointer increases by about
2^32 for every transmitted frame.
Fix by calculating the delta as a signed long.
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reported-by: Florian Bruhin <me@the-compiler.org>
Fixes: 7a1e890e21 ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix bad APMG configuration for 8000 (no AMPG on these devices)
* fix MAC address assignment for 8000
* fix firmware debugging triggers (MLME)
* fix several bugs in low power states code (net-detect,
d0i3)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bz0b
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2015-05-21' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* fix firmware name and other things to enable 3165
* fix bad APMG configuration for 8000 (no AMPG on these devices)
* fix MAC address assignment for 8000
* fix firmware debugging triggers (MLME)
* fix several bugs in low power states code (net-detect,
d0i3)
qos_seq points (to a struct) inside the command response data.
Make sure to free the response only after qos_seq is not
needed anymore.
Reported-by: Heng Luo <heng.luo@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There are buses that can't handle ASYNC command without
copying them. Duplicate the host command instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Take the MAC address from the OTP even if one is present in
the NVM, if that MAC address happens to be a reserved one.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
fw_status is the only pointer pointing to a block of memory
allocated above and should be freed after use.
Note: this come from Klockwork static analyzer.
Cc: stable@vger.kernel.org [3.19+]
Fixes: 2021a89d7b ("iwlwifi: mvm: treat netdetect wake up separately")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is an alternative way of fixing:
commit db9683fb41 ("net: phy: Make sure PHY_RESUMING state change
is always processed")
When the PHY state transitions from PHY_HALTED to PHY_RESUMING, there are
two things we need to do:
1). Re-enable interrupts (and power up the physical link, if powered down)
2). Update the PHY state and net-device based on the link status.
There's no strict reason why #1 has to be done from within the main
phy_state_machine() function. There is a risk that other changes to the
PHY (e.g. setting speed/duplex, which calls phy_start_aneg()) could cause
a subsequent state transition before phy_state_machine() has processed
the PHY_RESUMING state change. This would leave the PHY with interrupts
disabled and/or still in the BMCR_PDOWN/low-power mode.
Moving enabling the interrupts and phy_resume() into phy_start() will
guarantee this work always gets done. As the PHY is already in the HALTED
state and interrupts are disabled, it shouldn't conflict with any work
being done in phy_state_machine(). The downside of this change is that if
the PHY_RESUMING state is ever entered from anywhere else, it'll also have
to repeat this work.
Signed-off-by: Tim Beale <tim.beale@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
By inspection, this appears to be a typo. The gating comparison
involves vxlan->dev rather than dev. In fact, dev is the iterator in
the preceding loop above but it is actually constant in the 2nd loop.
Use of dev seems to be a bad cut-n-paste from the prior call to
unregister_netdevice_queue. Change dev to vxlan->dev, since that is
what is actually being checked.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the patch, the command 'ip link add bond2 type bond mode 802.3ad'
causes the kernel to send a rtnl message for the bond2 interface, with an
ifindex 0.
'ip monitor' shows:
0: bond2: <BROADCAST,MULTICAST,MASTER> mtu 1500 state DOWN group default
link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
9: bond2@NONE: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN group default
link/ether ea:3e:1f:53:92:7b brd ff:ff:ff:ff:ff:ff
[snip]
The patch fixes the spotted bug by checking in bond driver if the interface
is registered before calling the notifier chain.
It also adds a check in rtmsg_ifinfo() to prevent this kind of bug in the
future.
Fixes: d4261e5650 ("bonding: create netlink event when bonding option is changed")
CC: Jiri Pirko <jiri@resnulli.us>
Reported-by: Julien Meunier <julien.meunier@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
