Patch from Lennert Buytenhek
Add support for the LogicPD PXA270 Card Engine.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add an RTC subsystem driver for the ARM SA1100/PXA2XX processor RTC.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Add an EXPORT_SYMBOL for the Akita IO Expander Device.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
asm/arch/irq.h used to be included from asm/irq.h, but was removed
from the ARM kernel a long time ago. Consequently, the contents
of asm/arch/irq.h (which mostly contain a definition for fixup_irq())
have not been used. Hence, remove asm/arch/irq.h.
Some machine support files incorrectly included this file, making
little or no use of the contents. Move the contents to a local
include file, and remove those include statements as well.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
The turbo flag is in bit 0 of the CLKCFG register, not bit 1.
This patch corrects this so get_clk_frequency_khz returns a correct
value.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This field is redundent since it must be equal to PHYS_OFFSET anyway.
Now that no code uses it anymore, mark it deprecated and remove all
initializations from the tree.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The arm clock semaphores are strict mutexes, convert them to the new
mutex implementation
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some ARM platforms have the ability to program the interrupt controller to
detect various interrupt edges and/or levels. For some platforms, this is
critical to setup correctly, particularly those which the setting is dependent
on the device.
Currently, ARM drivers do (eg) the following:
err = request_irq(irq, ...);
set_irq_type(irq, IRQT_RISING);
However, if the interrupt has previously been programmed to be level sensitive
(for whatever reason) then this will cause an interrupt storm.
Hence, if we combine set_irq_type() with request_irq(), we can then safely set
the type prior to unmasking the interrupt. The unfortunate problem is that in
order to support this, these flags need to be visible outside of the ARM
architecture - drivers such as smc91x need these flags and they're
cross-architecture.
Finally, the SA_TRIGGER_* flag passed to request_irq() should reflect the
property that the device would like. The IRQ controller code should do its
best to select the most appropriate supported mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Fix a gcc4 build error (incomplete element type) in the pxa SharpSL
PM code.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that i2c_add_driver() doesn't need the module owner to be set by
hand, we can delete it from the drivers. This patch catches all of the
drivers that I found in the current tree (if a driver sets the .owner by
hand, it's not a problem, just not needed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jean Delvare <khali@linux-fr.org>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the drivers for arm arch.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
CC: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make I2C_CLIENT_ALLOW_USE the default for all i2c clients. It doesn't
hurt if the usage count is actually never used for any given driver,
and allows for nice code simplifications in i2c-core.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just about every i2c chip driver sets the I2C_DF_NOTIFY flag, so we
can simply make it the default and drop the flag. If any driver really
doesn't want to be notified when i2c adapters are added, that driver
can simply omit to set .attach_adapter. This approach is also more
robust as it prevents accidental NULL pointer dereferences.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Jared Hulbert
The following patch changes the bus arbiter controller settings
for the Intel PXA27x Application Processor Family. Up to 5%
better video performance. It parks the bus on the core while not
in use and sets the arbitration for other bus items. The patch
only applies changes to the Intel Mainstone development platform.
This patch is not compatible with preproduction Intel PXA27x
silicon.
This patch is based on the Intel Linux Preview Kit released to the
public on 25 Feb. 2005 found at
ftp://ftp.arm.linux.org.uk/pub/linux/arm/people/xscale/mainstone/02-25-2005/.
Signed-off-by: Justin A Treon <justin_treon@yahoo.com>
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
The SL-Cxx00 devices have a power control register in SCOOP that is
shared by both CF and MMC/SD card slots. The CF reset code was resetting
this register leading to various lockups as the MMC power was suddenly
lost. This patch handles the CPR register in a more sensitive manner.
It also removes some unneeded collie specific calls as the reset code
handles this.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch moves a large chunk of the sharpsl_pm driver to
arch/arm/common so that it can be reused on other devices such as the
SL-5500 (collie). It also abstracts some functions from the core into
the machine and platform specific parts of the driver to aid reuse.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add platform code to enable the ohci device on the pxa27x based
Sharp Zaurus Cxx00 devices.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To allow multiple platforms to use the PXA27x OHCI driver, the platform
code needs to be moved into the board specific files in
arch/arm/mach-pxa. This patch does this for mainstone and adds
preliminary hooks to allow other boards to use the driver.
This has been compile tested for mainstone and successfully run on Spitz
(Sharp Zaurus SL-C3000) with the addition of an appropriate board
support file.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Lothar Wassmann
The patch makes sure, that the ouptut functions of pins are restored
before restoring the Alternat Function settings, preventing pins from
being intermediately configured for undefined or unwanted alternate
functions.
Here is the original comment:
I've got a PXA270 system that uses GPIO80 as nCS4. This system did
hang on resume. Digging into the problem I found that the processor
stalled immediately when restoring the GAFR2_U register which restored
the alternate function for GPIO80. Since the GPDR registers were
restored after the GAFR registers, the offending GPIO was configured
as input at this point.
Thus the alternate function that was in effect after restoring the
GAFR was in fact the input function "MBREQ" instead of the output
function "nCS4". The "PXA27x Processor Family Developer's Manual"
(Footnote in Table 6-1 on page 6-3) states that:
"The MBREQ alternate function must not be enabled until the PSSR[RDH]
bit field is cleared. For more details, see Table 3-15, "PSSR Bit
Definitions" on page 3-71."
There is another note in the Developer's Manual (chapter 24.4.2
"GPIO operation as Alternate Function" on page 24-4)
stating that:
"Configuring a GPIO for an alternate function that is not defined for
it causes unpredictable results."
Since some GPIOs have no input function defined, and to prevent
inadvertedly programming the MBREQ function on some pin, the GAFR
registers should be restored after the GPDR registers have been
restored.
Additional provisions have to be made when the MBREQ function is
actually required. The corresponding GAFR bits should not be restored
with the regular GAFR restore, but must be set only after the PSSR
bits have been cleared.
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Akita requires inbuilt kernel i2c support for its GPIOs. Add this
requirement to Kconfig and update the defconfig to match.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add iWMMX Extentions for the pxa27x based Zaurus models and
fix a couple of minor mistakes in the PXA Kconfig file.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dirk Opfer
Fix an error in tosa.c after the platform device conversion.
Signed-off-by: Dirk Opfer <Dirk@Opfer-Online.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a driver for the extra GPIOs found on the Sharp SL-C1000 (Akita).
These GPIOs are found on a Maxim MAX7310 I2C i/o expander chip. A
generic GPIO driver for the MAX7310 was attempted but this mini
driver is a much simpler and much more effective solution avoiding
several issues and complexity the generic driver had (as discussed
on LKML).
The platform device is required so the device parent can be set
correctly which ensures the device is one of the last to suspend
and first to resume. Whilst the i2c suspend/resume calls can be
influenced, nothing guarantees this is easlier/later than the
subsystems the gpios are used on which are all independent of i2c
(sound, irda, video/backlight etc.).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a SharpSL PM device driver for the SL-Cxx00 machines.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a SharpSL PM device driver for the SL-C7x0 machines.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Updates to the SharpSL PM driver including cleanups from both
Pavel Machek and myself and updates after the platform device
changes to make it compile again.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add the core machine support for the Sharp SL-C1000 (Akita)
and enable the Kconfig selection for it.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Liam Girdwood
This patch allows users of the pxa SSP driver to register their own irq
handlers instead of using the default SSP handler. It also cleans up the
CKEN clock and irq detection as the values are now stored in a table.
This patch replaces 2845/1
Changes:-
o Added flags parameter to ssp_init()
o Added SSP_NO_IRQ flag to disable registering of ssp irq handler (for
drivers that want to register their own handler)
o Cleaned up clock and irq detection, values are now stored in table.
o Added build changes to allow other drivers (e.g audio) to select the
ssp driver.
o corgi_ssp.c changed to use new interface.
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch adds a power and battery management core driver which with
the addition of the right device files, supports the c7x0 and cxx00
series of Sharp Zaurus handhelds.
The driver is complex for several reasons. Battery charging is manually
monitored and controlled. When suspended, the device needs to
periodically partially resume, check the charging status and then
re-suspend. It does without bothering the higher linux layers as
a full resume and re-suspend is unnecessary. The code is carefully
written to avoid interrupts or calling code outside the module under
these circumstances. It also vets the various wake up sources and
monitors the device's power situation.
Hooks to limit the backlight intensity and to notify the battery
monitoring code of backlight events are connected/added as the
backlight is one of the biggest users of power on the device.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Nicolas Pitre
Make it completely deterministic and leave nothing to chance
(even if it had at worst 0.001% probability of failing).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dirk Opfer
This patch updates the tosa machine to use the new SharpSL PCMCIA layer introduced with Patch #3093/1
Depends on #3093/1
Signed-off-by: Dirk Opfer <Dirk@Opfer-Online.de>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
The Sharp SL-Cxx00 models have a combined power control for the SD
and CF slot 0. This patch adds hooks to the scoop driver to allow
machines to provide a custom control function for this and such a
function is added for spitz/akita/borzoi.
It also moves the gpio init code into the machine files as this
is machine dependent and differs between some models. A couple of
warnings when compiling for collie are also fixed.
Signed-off-by: Richard Purdie
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dirk Opfer
This patch adds MMC, IRDA and UDC support to the Sharp SL-6000x device. Also it adds a platform device for the keyboard driver.
Signed-off-by: Dirk Opfer
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix more include file problems that surfaced since I submitted the previous
fix-missing-includes.patch. This should now allow not to include sched.h
from module.h, which is done by a followup patch.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Update the PXA pm.c file to allow machines (such as the Sharp
Zaurus) to override the standard pm functions but reuse/wrap them
where needed.
The init call is made slightly earlier to give machine code an init
level to override them in removing any race.
Signed-off-by: Richard Purdie
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dirk Opfer
This patch adds basic machine support for the Sharp SL-6000x (Tosa) PDAs.
Signed-off-by: Dirk Opfer
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Todd Poynor
Add platform devices for flash to Lubbock and Mainstone board files.
Once in place, the two existing mtd map drivers for the boards will be
converted to use a single pxa2xx map driver in the linux-mtd tree.
Take 4: flash_platform_data .map_name vs. .name cleaned up, resync with
merged irda patch context.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
Lubbock updates:
* Provide an address for the SMC91x chip that doesn't generate
a boot-time warning (matching the EEPROM).
* Update MMC support to (a) detect card insert/remove, and
(b) report the readonly switch setting for SD cards.
Previously, MMC/SD cards had to be present at boot time else they
couldn't be detected.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
