Show more info for interrupt only lines in debugfs. It's useful
to monitor the lines that have been never requested as GPIOs,
but IRQs.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240530191418.1138003-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add support for the TI TCA9535 variant.
The NXP PCA9535 is already supported by the driver.
TCA9535 supports lower voltage operation (down to 1.65V VCC)
compared to PCA (down to 2.3V VCC).
>From a software perspective, these models are equivalent as they
have the same register map.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20240531121801.2161154-1-festevam@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The GPIO_BRCMSTB hardware IP is also included in the bcm2712
SoC so enable the driver to also be built for ARCH_BCM2835.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240530181737.1261450-1-pbrobinson@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The handling of kfifo_out() errors in read functions obscures any error.
The error condition should never occur but, while a ret is set to -EIO, it
is subsequently ignored and the read functions instead return the number
of bytes copied to that point, potentially masking the fact that any error
occurred.
Log a warning and return -EIO in the case of a kfifo_out() error to make
it clear something very odd is going on here.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240529131953.195777-4-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The allocation of the linereq events kfifo is performed in two separate
places. Add a helper function to remove the duplication.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240529131953.195777-3-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The initialisation of the linereq events kfifo relies on the struct being
zeroed and a subsequent call to kfifo_alloc(). The call to kfifo_alloc()
is deferred until edge detection is first enabled for the linereq. If the
kfifo is inadvertently accessed before the call to kfifo_alloc(), as was
the case in a recently discovered bug, it behaves as a FIFO of size 1 with
an element size of 0, so writes and reads to the kfifo appear successful
but copy no actual data.
As a defensive measure, initialise the kfifo with INIT_KFIFO() when the
events kfifo is constructed. This initialises the kfifo element size
and zeroes its data pointer, so any inadvertant access prior to the
kfifo_alloc() call will trigger an oops.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240529131953.195777-2-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
rdc_gpio_config() uses pci_{read,write}_config_dword() that return
PCIBIOS_* codes. rdc_gpio_config() is used for
direction_{input,output}() in the struct gpio_chip which both require
normal errnos to be returned.
Similarly, rdc321x_gpio_probe() that is probe function returns
PCIBIOS_* codes without converting them first into normal errnos.
Convert PCIBIOS_* returns code using pcibios_err_to_errno() into normal
errno before returning them to fix both issues.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240527132345.13956-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
amd_gpio_init() uses pci_read_config_dword() that returns PCIBIOS_*
codes. The return code is then returned as is but amd_gpio_init() is
a module init function that should return normal errnos.
Convert PCIBIOS_* returns code using pcibios_err_to_errno() into normal
errno before returning it from amd_gpio_init().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240527132345.13956-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Do not issue "can't read the data register offset!" when gpio,syscon-dev
is not set albeit unneeded. gpio-syscon is used with rk3328 chip, but
this iomem region is documented in
Documentation/devicetree/bindings/gpio/rockchip,rk3328-grf-gpio.yaml and
does not require gpio,syscon-dev setting.
Signed-off-by: Etienne Buira <etienne.buira@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/Zktwd4Y8zu6XSGaE@Z926fQmE5jqhFMgp6
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Userspace may trigger a speculative read of an address outside the gpio
descriptor array.
Users can do that by calling gpio_ioctl() with an offset out of range.
Offset is copied from user and then used as an array index to get
the gpio descriptor without sanitization in gpio_device_get_desc().
This change ensures that the offset is sanitized by using
array_index_nospec() to mitigate any possibility of speculative
information leaks.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Signed-off-by: Hagar Hemdan <hagarhem@amazon.com>
Link: https://lore.kernel.org/r/20240523085332.1801-1-hagarhem@amazon.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Several new features here:
- virtio-net is finally supported in vduse.
- Virtio (balloon and mem) interaction with suspend is improved
- vhost-scsi now handles signals better/faster.
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmZN570PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp2JUH/1K3fZOHymop6Y5Z3USFS7YdlF+dniedY/vg
TKyWERkXOlxq1d9DVxC0mN7tk72DweuWI0YJjLXofrEW1VuW29ecSbyFXxpeWJls
b7ErffxDAFRas5jkMCngD8TuFnbEegU0mGP5kbiHpEndBydQ2hH99Gg0x7swW+cE
xsvU5zonCCLwLGIP2DrVrn9qGOHtV6o8eZfVKDVXfvicn3lFBkUSxlwEYsO9RMup
aKxV4FT2Pb1yBicwBK4TH1oeEXqEGy1YLEn+kAHRbgoC/5L0/LaiqrkzwzwwOIPj
uPGkacf8CIbX0qZo5EzD8kvfcYL1xhU3eT9WBmpp2ZwD+4bINd4=
=nax1
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"Several new features here:
- virtio-net is finally supported in vduse
- virtio (balloon and mem) interaction with suspend is improved
- vhost-scsi now handles signals better/faster
And fixes, cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (48 commits)
virtio-pci: Check if is_avq is NULL
virtio: delete vq in vp_find_vqs_msix() when request_irq() fails
MAINTAINERS: add Eugenio Pérez as reviewer
vhost-vdpa: Remove usage of the deprecated ida_simple_xx() API
vp_vdpa: don't allocate unused msix vectors
sound: virtio: drop owner assignment
fuse: virtio: drop owner assignment
scsi: virtio: drop owner assignment
rpmsg: virtio: drop owner assignment
nvdimm: virtio_pmem: drop owner assignment
wifi: mac80211_hwsim: drop owner assignment
vsock/virtio: drop owner assignment
net: 9p: virtio: drop owner assignment
net: virtio: drop owner assignment
net: caif: virtio: drop owner assignment
misc: nsm: drop owner assignment
iommu: virtio: drop owner assignment
drm/virtio: drop owner assignment
gpio: virtio: drop owner assignment
firmware: arm_scmi: virtio: drop owner assignment
...
virtio core already sets the .owner, so driver does not need to.
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Message-Id: <20240331-module-owner-virtio-v2-12-98f04bfaf46a@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Previous patch modified the standard used by acpi_gpiochip_find()
to match device nodes. Using the device node set in gc->gpiodev->d-
ev instead of gc->parent.
However, there is a situation in gpio-dwapb where the GPIO device
driver will set gc->fwnode for each port corresponding to a child
node under a GPIO device, so gc->gpiodev->dev will be assigned the
value of each child node in gpiochip_add_data().
gpio-dwapb.c:
128,31 static int dwapb_gpio_add_port(struct dwapb_gpio *gpio,
struct dwapb_port_property *pp,
unsigned int offs);
port->gc.fwnode = pp->fwnode;
693,39 static int dwapb_gpio_probe;
err = dwapb_gpio_add_port(gpio, &pdata->properties[i], i);
When other drivers request GPIO pin resources through the GPIO device
node provided by ACPI (corresponding to the parent node), the change
of the matching object to gc->gpiodev->dev in acpi_gpiochip_find()
only allows finding the value of each port (child node), resulting
in a failed request.
Reapply the condition of using gc->parent for match in acpi_gpio-
chip_find() in the code can compatible with the problem of gpio-dwapb,
and will not affect the two cases mentioned in the patch:
1. There is no setting for gc->fwnode.
2. The case that depends on using gc->fwnode for match.
Fixes: 5062e4c14b ("gpiolib: acpi: use the fwnode in acpi_gpiochip_find()")
Fixes: 067dbc1ea5 ("gpiolib: acpi: Don't use GPIO chip fwnode in acpi_gpiochip_find()")
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Following the relocation of the function call outside of
__acpi_find_gpio(), move the ACPI device NULL check to
acpi_can_fallback_to_crs().
Signed-off-by: Laura Nao <laura.nao@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reported-by: kernelci.org bot <bot@kernelci.org>
Closes: https://lore.kernel.org/all/20240426154208.81894-1-laura.nao@collabora.com/
Fixes: 49c02f6e90 ("gpiolib: acpi: Move acpi_can_fallback_to_crs() out of __acpi_find_gpio()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
GPIO core:
- remove more unused legacy interfaces (after converting the last remaining
users to better alternatives)
- update kerneldocs
- improve error handling and log messages in GPIO ACPI code
- remove dead code (always true checks) from GPIOLIB
New drivers:
- add a driver for Intel Granite Rapids-D vGPIO
Driver improvements:
- use -ENOTSUPP consistently in gpio-regmap and gpio-pcie-idio-24
- provide an ID table for gpio-cros-ec to avoid a driver name fallback check
- add support for gpio-ranges for GPIO drivers supporting multiple GPIO banks
- switch to using dynamic GPIO base in gpio-brcmstb
- fix irq handling in gpio-npcm-sgpio
- switch to memory mapped IO accessors in gpio-sch
DT bindings:
- add support for gpio-ranges to gpio-brcmstb
- add support for a new model and the gpio-line-names property to gpio-mpfs
Documentation:
- replace leading tabs with spaces in code blocks
- fix typos
-----BEGIN PGP SIGNATURE-----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=mBWd
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski
"This was a quiet release cycle for the GPIO tree and so this
pull-request is relatively small.
We have one new driver, some minor improvements to the GPIO core code
and across several drivers, some DT and documentation updates but in
general nothing stands out or is controversial. All changes have spent
time in next with no reported issues (or ones that were quickly
fixed).
GPIO core:
- remove more unused legacy interfaces (after converting the last
remaining users to better alternatives)
- update kerneldocs
- improve error handling and log messages in GPIO ACPI code
- remove dead code (always true checks) from GPIOLIB
New drivers:
- add a driver for Intel Granite Rapids-D vGPIO
Driver improvements:
- use -ENOTSUPP consistently in gpio-regmap and gpio-pcie-idio-24
- provide an ID table for gpio-cros-ec to avoid a driver name
fallback check
- add support for gpio-ranges for GPIO drivers supporting multiple
GPIO banks
- switch to using dynamic GPIO base in gpio-brcmstb
- fix irq handling in gpio-npcm-sgpio
- switch to memory mapped IO accessors in gpio-sch
DT bindings:
- add support for gpio-ranges to gpio-brcmstb
- add support for a new model and the gpio-line-names property to
gpio-mpfs
Documentation:
- replace leading tabs with spaces in code blocks
- fix typos"
* tag 'gpio-updates-for-v6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (30 commits)
gpio: nuvoton: Fix sgpio irq handle error
gpiolib: Discourage to use formatting strings in line names
gpio: brcmstb: add support for gpio-ranges
gpio: of: support gpio-ranges for multiple gpiochip devices
dt-bindings: gpio: brcmstb: add gpio-ranges
gpio: Add Intel Granite Rapids-D vGPIO driver
gpio: brcmstb: Use dynamic GPIO base numbers
gpiolib: acpi: Set label for IRQ only lines
gpiolib: acpi: Add fwnode name to the GPIO interrupt label
gpiolib: Get rid of never false gpio_is_valid() calls
gpiolib: acpi: Pass con_id instead of property into acpi_dev_gpio_irq_get_by()
gpiolib: acpi: Move acpi_can_fallback_to_crs() out of __acpi_find_gpio()
gpiolib: acpi: Simplify error handling in __acpi_find_gpio()
gpiolib: acpi: Extract __acpi_find_gpio() helper
gpio: sch: Utilise temporary variable for struct device
gpio: sch: Switch to memory mapped IO accessors
gpio: regmap: Use -ENOTSUPP consistently
gpio: pcie-idio-24: Use -ENOTSUPP consistently
Documentation: gpio: Replace leading TABs by spaces in code blocks
gpiolib: acpi: Check for errors first in acpi_find_gpio()
...
The diffstat for this release is dominated by the new Airoha driver,
mainly as a result of this being a generally quite quiet release. There
were a couple of cleanups in the core but nothing substantial, the
updates here are almost all driver specific ones.
- Support for multi-word mode in the OMAP2 McSPI driver.
- Overhaul of the PXA2xx driver, mostly API updates.
- A number of DT binding conversions.
- Support for Airoha NAND controllers, Cirrus Logic CS35L56, Mobileye
EYEQ5 and Renesas R8A779H0.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmZB2z0ACgkQJNaLcl1U
h9CCxgf/ZSy6jKbUejdq/JtdrhVCamaEVQ1X5FAk18wlumQVwFC/Bsntr1hVWDjg
Ai+G/UYWtfabyVePZKh1zCcoloSuZheHcxAMP+43un1doWcHps6leiPfb9yAysux
VxeIBfSUOfeFbN697Jz8PDTIhxHMUh0R4QYqqIyrT1RSS0alRZoDyaQpTWied0Nt
pOUWi9SVt0jm/G+X29a6Q/pFsr0oEJHxZgvriwlJAyzWr1OModFXdTfdK+qMS1Hn
huafVu4bWCEognGlnXCQSRL94Fxo1nab1PvMuWK2VXNDL7xexqQ33cp4VILZvJo1
qR9YtiRXpScAmO7f8ccGcSlz8vw5jQ==
=x3Vz
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The diffstat for this release is dominated by the new Airoha driver,
mainly as a result of this being a generally quite quiet release.
There were a couple of cleanups in the core but nothing substantial,
the updates here are almost all driver specific ones.
- Support for multi-word mode in the OMAP2 McSPI driver
- Overhaul of the PXA2xx driver, mostly API updates
- A number of DT binding conversions
- Support for Airoha NAND controllers, Cirrus Logic CS35L56, Mobileye
EYEQ5 and Renesas R8A779H0"
* tag 'spi-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: dw: Bail out early on unsupported target mode
spi: Remove unneded check for orig_nents
MAINTAINERS: repair file entry in AIROHA SPI SNFI DRIVER
spi: pxa2xx: Drop the stale entry in documentation TOC
spi: pxa2xx: Don't provide struct chip_data for others
spi: pxa2xx: Remove timeout field from struct chip_data
spi: pxa2xx: Remove DMA parameters from struct chip_data
spi: pxa2xx: Drop struct pxa2xx_spi_chip
spi: pxa2xx: Don't use "proxy" headers
spi: pxa2xx: Remove outdated documentation
spi: pxa2xx: Move contents of linux/spi/pxa2xx_spi.h to a local one
spi: pxa2xx: Provide num-cs for Sharp PDAs via device properties
spi: pxa2xx: Allow number of chip select pins to be read from property
spi: dt-bindings: ti,qspi: convert to dtschema
spi: bitbang: Add missing MODULE_DESCRIPTION()
spi: bitbang: Use NSEC_PER_*SEC rather than hard coding
spi: dw: Drop default number of CS setting
spi: dw: Convert dw_spi::num_cs to u32
spi: dw: Add a number of native CS auto-detection
spi: dw: Convert to using BITS_TO_BYTES() macro
...
If a line is requested with debounce, and that results in debouncing
in software, and the line is subsequently reconfigured to enable edge
detection then the allocation of the kfifo to contain edge events is
overlooked. This results in events being written to and read from an
uninitialised kfifo. Read events are returned to userspace.
Initialise the kfifo in the case where the software debounce is
already active.
Fixes: 65cff70464 ("gpiolib: cdev: support setting debounce")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20240510065342.36191-1-warthog618@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The use-after-free issue occurs as follows: when the GPIO chip device file
is being closed by invoking gpio_chrdev_release(), watched_lines is freed
by bitmap_free(), but the unregistration of lineinfo_changed_nb notifier
chain failed due to waiting write rwsem. Additionally, one of the GPIO
chip's lines is also in the release process and holds the notifier chain's
read rwsem. Consequently, a race condition leads to the use-after-free of
watched_lines.
Here is the typical stack when issue happened:
[free]
gpio_chrdev_release()
--> bitmap_free(cdev->watched_lines) <-- freed
--> blocking_notifier_chain_unregister()
--> down_write(&nh->rwsem) <-- waiting rwsem
--> __down_write_common()
--> rwsem_down_write_slowpath()
--> schedule_preempt_disabled()
--> schedule()
[use]
st54spi_gpio_dev_release()
--> gpio_free()
--> gpiod_free()
--> gpiod_free_commit()
--> gpiod_line_state_notify()
--> blocking_notifier_call_chain()
--> down_read(&nh->rwsem); <-- held rwsem
--> notifier_call_chain()
--> lineinfo_changed_notify()
--> test_bit(xxxx, cdev->watched_lines) <-- use after free
The side effect of the use-after-free issue is that a GPIO line event is
being generated for userspace where it shouldn't. However, since the chrdev
is being closed, userspace won't have the chance to read that event anyway.
To fix the issue, call the bitmap_free() function after the unregistration
of lineinfo_changed_nb notifier chain.
Fixes: 51c1064e82 ("gpiolib: add new ioctl() for monitoring changes in line info")
Signed-off-by: Zhongqiu Han <quic_zhonhan@quicinc.com>
Link: https://lore.kernel.org/r/20240505141156.2944912-1-quic_zhonhan@quicinc.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
We used a per-descriptor SRCU struct in order to not impose a wait with
synchronize_srcu() for descriptor X on read-only operations of
descriptor Y. Now that we no longer call synchronize_srcu() on
descriptor label change but only when releasing descriptor resources, we
can use a single SRCU structure for all GPIO descriptors in a given chip.
Suggested-by: "Paul E. McKenney" <paulmck@kernel.org>
Acked-by: "Paul E. McKenney" <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20240507172414.28513-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Commit 1f2bcb8c8c ("gpio: protect the descriptor label with SRCU")
caused a massive drop in performance of requesting GPIO lines due to the
call to synchronize_srcu() on each label change. Rework the code to not
wait until all read-only users are done with reading the label but
instead atomically replace the label pointer and schedule its release
after all read-only critical sections are done.
To that end wrap the descriptor label in a struct that also contains the
rcu_head struct required for deferring tasks using call_srcu() and stop
using kstrdup_const() as we're required to allocate memory anyway. Just
allocate enough for the label string and rcu_head in one go.
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Closes: https://lore.kernel.org/linux-gpio/CAMRc=Mfig2oooDQYTqo23W3PXSdzhVO4p=G4+P8y1ppBOrkrJQ@mail.gmail.com/
Fixes: 1f2bcb8c8c ("gpio: protect the descriptor label with SRCU")
Suggested-by: "Paul E. McKenney" <paulmck@kernel.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Acked-by: "Paul E. McKenney" <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20240507121346.16969-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The generic_handle_domain_irq() function calls irq_resolve_mapping().
Thus delete a duplicative irq_find_mapping() call
so that a stack trace and an RCU stall will be avoided.
Fixes: c4f8457d17 ("gpio: nuvoton: Add Nuvoton NPCM sgpio driver")
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20240506064244.1645922-1-JJLIU0@nuvoton.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
* New driver for vGPIO controller on Intel Granite Rapids-D
* Update ACPI GPIO library to unify the IRQ code path
* Better GPIO IRQ line labeling for ACPI
* Switched Intel SCH driver to use "mapped" I/O accessors
The following is an automated git shortlog grouped by driver:
Add Intel Granite Rapids-D vGPIO driver:
- Add Intel Granite Rapids-D vGPIO driver
crystalcove:
- Use -ENOTSUPP consistently
gpiolib:
- acpi: Set label for IRQ only lines
- acpi: Add fwnode name to the GPIO interrupt label
- acpi: Pass con_id instead of property into acpi_dev_gpio_irq_get_by()
- acpi: Move acpi_can_fallback_to_crs() out of __acpi_find_gpio()
- acpi: Simplify error handling in __acpi_find_gpio()
- acpi: Extract __acpi_find_gpio() helper
- acpi: Check for errors first in acpi_find_gpio()
- acpi: Remove never true check in acpi_get_gpiod_by_index()
sch:
- Utilise temporary variable for struct device
- Switch to memory mapped IO accessors
wcove:
- Use -ENOTSUPP consistently
-----BEGIN PGP SIGNATURE-----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=33sC
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-next
intel-gpio for v6.10-1
* New driver for vGPIO controller on Intel Granite Rapids-D
* Update ACPI GPIO library to unify the IRQ code path
* Better GPIO IRQ line labeling for ACPI
* Switched Intel SCH driver to use "mapped" I/O accessors
The following is an automated git shortlog grouped by driver:
Add Intel Granite Rapids-D vGPIO driver:
- Add Intel Granite Rapids-D vGPIO driver
crystalcove:
- Use -ENOTSUPP consistently
gpiolib:
- acpi: Set label for IRQ only lines
- acpi: Add fwnode name to the GPIO interrupt label
- acpi: Pass con_id instead of property into acpi_dev_gpio_irq_get_by()
- acpi: Move acpi_can_fallback_to_crs() out of __acpi_find_gpio()
- acpi: Simplify error handling in __acpi_find_gpio()
- acpi: Extract __acpi_find_gpio() helper
- acpi: Check for errors first in acpi_find_gpio()
- acpi: Remove never true check in acpi_get_gpiod_by_index()
sch:
- Utilise temporary variable for struct device
- Switch to memory mapped IO accessors
wcove:
- Use -ENOTSUPP consistently
A pin controller device mapped with the gpio-ranges property
will need implementations of the .request and .free members of
the gpiochip.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Tested-by: Phil Elwell <phil@raspberrypi.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240424185039.1707812-4-opendmb@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Some drivers (e.g. gpio-mt7621 and gpio-brcmstb) have multiple
gpiochip banks within a single device. Unfortunately, the
gpio-ranges property of the device node was being applied to
every gpiochip of the device with device relative GPIO offset
values rather than gpiochip relative GPIO offset values.
This commit makes use of the gpio_chip offset value which can be
non-zero for such devices to split the device node gpio-ranges
property into GPIO offset ranges that can be applied to each
of the relevant gpiochips of the device.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240424185039.1707812-3-opendmb@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
* Make data pointer dereference robust in Intel Tangier driver
The following is an automated git shortlog grouped by driver:
tangier:
- Use correct type for the IRQ chip data
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEqaflIX74DDDzMJJtb7wzTHR8rCgFAmYqRFQACgkQb7wzTHR8
rCi5pBAAqbwggKHNuIf4WOqHkwjHgS5VnRUxcBtX3u83piSuSHJ5x+AemL3SIbdn
1lINHv1rTB589KeyT9erbxdwBP8ggERuQvf9DrWZo1jibzqNDUN84wq/yC9ITG8M
JNymf/zpTEIgOidt4XwfK8xzSlCSuUtwVawXtA4WyQ8vYYAe2Lqb0SYlVlXvm4v9
mllNuNmxL2uR/4KVNysw2qTWHF9+MifsM3whS6a/y0Ymh3Aay3ehRf3Lc06ZGWF+
i7LbKoVyIa69w0WHk/QD1YCQJ+wS20w8XAauw0nUHorShckIc8/1AX3INAT7ZjcT
V71mTCsPUvakgjQEpWzsOoRhv7F8opvwGeibzxU9RciOV3vydRQXR+43rp8kkPG0
DYKTmOcE2EzwRWlGP3+IZMkp+XHk3qoNUBcI6+6PwXFvScyo5rxJ3a00hyJ4wovH
+gIYnT2vVbSaMWJSMClz6p/QCrkMh+cVNsSk3efQ/OcD+6XTWOFZQMPZ9hIS85jX
LwCjn9KjJA+Y5780n3qaoCcJmlp+sYnCGRhwid/ZiZH17S9tKjPOByPvOoFf8qxd
mSlyD9hu0CnP+e3JbUQl/g2er0/rjotSKKloUWDP9z+J0n9DDABlUWkmeMbJli1/
ON3p8/W4blEkXtKaBxbwOwnymOazDzd6JRohfPzvRV7pcLLGAJQ=
=688G
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-current
intel-gpio for v6.9-2
* Make data pointer dereference robust in Intel Tangier driver
The following is an automated git shortlog grouped by driver:
tangier:
- Use correct type for the IRQ chip data
This driver provides a basic GPIO driver for the Intel Granite Rapids-D
virtual GPIOs. On SoCs with limited physical pins on the package, the
physical pins controlled by this driver would be exposed on an external
device such as a BMC or CPLD. The virtual GPIO registers are an
interface to firmware, which communicates with the external device that
implements the GPIO hardware functionality.
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The controller has several register bits describing access control
information for a given GPIO pin. When SCR_SEC_[R|W]EN is unset, it
means we have full read/write access to all the registers for given GPIO
pin. When SCR_SEC[R|W]EN is set, it means we need to further check the
accompanying SCR_SEC_G1[R|W] bit to determine read/write access to all
the registers for given GPIO pin.
This check was previously declaring that a GPIO pin was accessible
only if either of the following conditions were met:
- SCR_SEC_REN + SCR_SEC_WEN both set
or
- SCR_SEC_REN + SCR_SEC_WEN both set and
SCR_SEC_G1R + SCR_SEC_G1W both set
Update the check to properly handle cases where only one of
SCR_SEC_REN or SCR_SEC_WEN is set.
Fixes: b2b56a1632 ("gpio: tegra186: Check GPIO pin permission before access.")
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240424095514.24397-1-pshete@nvidia.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Forcing a gpiochip to have a fixed base number now leads to a warning
message. Remove the need to do so by using the offset value of the
gpiochip.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240423184605.2094376-1-opendmb@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
When line locked as IRQ it has no label assigned. Assign
the meaningful value to it.
Ex. (for the PCA9355 and MAX3111e chips connected to the system):
=== Before ===
PCA953x: interrupt
MAX3111e: interrupt
=== After ===
PCA953x: NIO1 GpioInt(0)
MAX3111e: URT0 GpioInt(0)
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It's ambiguous to have a device-related index in the GPIO interrupt
label as most of the devices will have it the same or very similar.
Extend label with fwnode name for better granularity. It significantly
reduces the scope of searching among devices.
Ex. (for the PCA9355 and MAX3111e chips connected to the system):
=== Before ===
PCA953x: GpioInt() 0
MAX3111e: GpioInt() 0
=== After ===
PCA953x: NIO1 GpioInt(0)
MAX3111e: URT0 GpioInt(0)
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In the cases when gpio_is_valid() is called with unsigned parameter
the result is always true in the GPIO library code, hence the check
for false won't ever be true. Get rid of such calls.
While at it, move GPIO device base to be unsigned to clearly show
it won't ever be negative. This requires a new definition for the
maximum GPIO number in the system.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
SPI devices can specify a cs-gpios property to enumerate their
chip selects. Under device tree, a zero entry in this property can
be used to specify that a particular chip select is using the SPI
controllers native chip select, for example:
cs-gpios = <&gpio1 0 0>, <0>;
Here, the second chip select is native. However, when using swnodes
there is currently no way to specify a native chip select. The
proposal here is to register a swnode_gpio_undefined software node,
that can be specified to allow the indication of a native chip
select. For example:
static const struct software_node_ref_args device_cs_refs[] = {
{
.node = &device_gpiochip_swnode,
.nargs = 2,
.args = { 0, GPIO_ACTIVE_LOW },
},
{
.node = &swnode_gpio_undefined,
.nargs = 0,
},
};
Register the swnode as the gpiolib is initialised and check in
swnode_get_gpio_device() if the returned node matches
swnode_gpio_undefined and return -ENOENT, which matches the
behaviour of the device tree system when it encounters a 0 phandle.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240416100904.3738093-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pass the con_id instead of property so that callers won't repeat
the GPIO suffixes to try.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
New coming user may need to check for _CRS fallback slightly differently.
Move the current check out of the helper function to allow that user to
use it.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Now that we don't perform anything on the GPIO descriptor,
we may simplify the error path in newly introduced helper.
Do it so.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We want to reuse it later on in the code. In particular, it helps
to clean up the users of acpi_dev_gpio_irq_wake_get_by().
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We have a temporary variable to keep a pointer to struct device.
Utilise it where it makes sense.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
IRQ chip data contains a pointer to the GPIO chip. Luckily we have
the pointers the same, but strictly speaking it's not guaranteed.
Even though, still better to fix this.
Fixes: ccf6fd6dcc ("gpio: merrifield: Introduce GPIO driver to support Merrifield")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The GPIO library expects the drivers to return -ENOTSUPP in some cases
and not using analogue POSIX code. Make the driver to follow this.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The GPIO library expects the drivers to return -ENOTSUPP in some cases
and not using analogue POSIX code. Make the driver to follow this.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: William Breathitt Gray <wbg@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add MODULE_DEVICE_TABLE(), so the module could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
It's better to parse the code when the usual pattern is being used,
i.e. checking for error condition first.
There is no functional or code generation change (tested in LLVM).
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The acpi_get_gpiod_by_index() never is called with adev being NULL.
Remove the redundant check.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
* Fix returned code in the error path in Intel PMIC GPIO drivers
The following is an automated git shortlog grouped by driver:
crystalcove:
- Use -ENOTSUPP consistently
wcove:
- Use -ENOTSUPP consistently
-----BEGIN PGP SIGNATURE-----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=nT1m
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-current
intel-gpio for v6.9-1
* Fix returned code in the error path in Intel PMIC GPIO drivers
The following is an automated git shortlog grouped by driver:
crystalcove:
- Use -ENOTSUPP consistently
wcove:
- Use -ENOTSUPP consistently
The GPIO library expects the drivers to return -ENOTSUPP in some
cases and not using analogue POSIX code. Make the driver to follow
this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The GPIO library expects the drivers to return -ENOTSUPP in some
cases and not using analogue POSIX code. Make the driver to follow
this.
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When adding sanitization of the label, the path through
edge_detector_setup() that leads to debounce_setup() was overlooked.
A request taking this path does not allocate a new label and the
request label is freed twice when the request is released, resulting
in memory corruption.
Add label sanitization to debounce_setup().
Cc: stable@vger.kernel.org
Fixes: b34490879b ("gpio: cdev: sanitize the label before requesting the interrupt")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
[Bartosz: rebased on top of the fix for empty GPIO labels]
Co-developed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
