In situations where zoning is not being used, thus NVMe initiators see
other NVMe initiators as well as NVMe targets, a link bounce on an
initiator will cause the NVMe initiators to spew "6169" State Error
messages.
The driver is not qualifying whether the remote port is a NVMe targer or
not before calling the lpfc_nvme_rescan_port(), which validates the role
and prints the message if its only an NVMe initiator.
Fix by the following:
- Before calling lpfc_nvme_rescan_port() ensure that the node is a NVMe
storage target or a NVMe discovery controller.
- Clean up implementation of lpfc_nvme_rescan_port. remoteport pointer
will always be NULL if a NVMe initiator only. But, grabbing of
remoteport pointer should be done under lock to coincide with the
registering of the remote port with the fc transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On an SLI-3 adapter which does not support NVMe, but with the driver global
attribute to enable nvme on any adapter if it does support NVMe
(e.g. module parameter lpfc_enable_fc4_type=3), the SGL and total SGE
values are being munged by the protocol enablement when it shouldn't be.
Correct by changing the location of where the NVME sgl information is being
applied, which will avoid any SLI-3-based adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If admin changes the devloss_tmo on an rport via the fc_remote_port rport
dev_loss_tmo attribute, the value is on set on scsi stack. The change is
not propagated to NVMe.
The set routine in the lldd lacks the call to
nvme_fc_set_remoteport_devloss() to set the value.
Fix by adding the call to the lldd set routine.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In tests with remote ports contantly logging out/logging coupled with
occassional local link bounce, if a remote port is disocnnected for longer
than devloss_tmo and then subsequently reconnected, eventually the test
will fail to login with the remote port and remote port connectivity is
lost.
When devloss_tmo expires, the driver does not free the node struct until
the port or npiv instances is being deleted. The node is left allocated but
the state set to UNUSED. If the node was in the process of logging in when
the local link drop occurred, meaning the RPI was allocated for the node in
order to send the ELS, but not yet registered which comes after successful
login, the node is moved to the NPR state, and if devloss expires, to
UNUSED state. If the remote port comes back, the node associated with it
is restarted and this path happens to allocate a new RPI and overwrites the
prior RPI value. In the cases where the port was logged in and loggs out,
the path did release the RPI but did not set the node rpi value. In the
cases where the remote port never finished logging in, the path never did
the call to release the rpi. In this latter case, when the node is
subsequently restore, the new rpi allocation overwrites the rpi that was
not released, and the rpi is now leaked. Eventually the port will run out
of RPI resources to log into new remote ports.
Fix by following changes:
- When an rpi is released, do so under locks and ensure the node rpi value
is set to a non-allocated value (LPFC_RPI_ALLOC_ERROR). Note:
refactored to a small service routine to avoid indentation issues.
- When re-enabling a node, check the rpi value to determine if a new
allocation is necessary. If already set, use the prior rpi.
Enhanced logging to help in the future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a remote port is removed and remains removed for devloss_tmo, if an RSCN
is subsequently received indicating the presence of the remte port, the
driver does not login to and rediscovery the remote port.
Currently, in order to for a port to be rediscovered post an RSCN, the node
state must be NPR to reflect not logged in. When devloss expires, the node
state is marked UNUSED. When an RSCN occurs, the nodes referenced by the
RSCN will have a NPR_2B_DISC flag set, but the re-login will only be
attempted if the node is in NPR_NODE state. Thus the node is skipped over.
Fix by recognizing the NPR_2B_DISC and UNUSED and transition the node back
to NPR state to allow the re-login to take place.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an admin updates lpfc's devloss_tmo sysfs attribute, the kernel will
oops.
Coding of a loop allowed a new value (rport) to be set/checked for null
followed by an older value (remoteport) checked for null to allow progress
where the new value, even though null, will be referenced.
Rework the logic to validate and prevent any reference to the null ptr.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's possible for the driver to initiate an FLOGI and before it completes,
another link down/up transition occurs requiring a new FLOGI. Currently,
nothing is done to abort/noop the older FLOGI request to the adapter, so if
this transition occurs and the FLOGI completion is received after the link
down/up transition, the driver may erroneously act on the older FLOGI. In
most cases, the adapter properly terminates/fails the FLOGI, but there is a
timing condition where the FLOGI may complete on the wire prior to the
transition, but the response may not be seen/processed by the driver before
the driver sees the link transition.
Fix by having the link down handler in the driver run through any
outstanding ELS's and change the completion handler of the ELS so that it
will be no-op'd and released.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When tearing down the adapter for a reset, online/offline, or driver
unload, the queue free routine would hit a GPF oops. This only occurs on
conditions where the number of hardware queues created is fewer than the
number of cpus in the system. In this condition cpus share a hardware
queue. And of course, it's the 2nd cpu that shares a hardware that
attempted to free it a second time and hit the oops.
Fix by reworking the cpu to hardware queue mapping such that:
Assignment of hardware queues to cpus occur in two passes:
first pass: is first time assignment of a hardware queue to a cpu.
This will set the LPFC_CPU_FIRST_IRQ flag for the cpu.
second pass: for cpus that did not get a hardware queue they will
be assigned one from a primary cpu (one set in first pass).
Deletion of hardware queues is driven by cpu itteration, and queues
will only be deleted if the LPFC_CPU_FIRST_IRQ flag is set.
Also contains a few small cleanup fixes and a little better logging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The adapter reset path (lpfc_sli_hba_down) is taking/releasing a lock with
irq. But, the path is already under the hbalock which raised irq so it's
unnecessary.
Convert to simple lock/unlock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_nvme_register_port hit a null prev_ndlp pointer in a test with lots of
target ports swapping addresses. The oldport value was stale, thus it's
ndlp (prev_ndlp set to it) was used.
Fix by moving oldrport pointer checks, and if used prev_ndlp pointer
assignment, to be done while the lock is held.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is inadvertently trying to issue an INIT_VPI mailbox command on
an SLI-3 driver. The command is specific to SLI-4. When the call is made to
send the command, if on an SLI-3 adapter, an array pointer is NULL and the
driver will oops.
Fix by restricting the command to SLI-4 adapters only.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a target issues an ADISC to the port and the target is a NVME target,
the driver is inadvertantly invalidating the login and marking the remote
port as logged out. Communication with the target is lost.
Revise the ADISC check so that FCP or NVME targets will be marked valid at
the end of ADISC processing. Enhance logging to recognize condition
better.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some remote ports may be slow in registering their GID_FT protocol
information with the fabric. If the remote port is an initiator, it may
send PLOGI to the port before the GID_FT logic is complete. Meaning, after
accepting the PLOGI, when the driver may see no response to the GID_FT that
is issued after the login to determine the protocols supported so that
proper PRLI's may be transmit. If the driver has no fc4 information, it
currently stops and the remote port is not discovered.
Fix by issuing a LOGO when there is no GID_FT information. The LOGO
completion handling will attempt to re-login if the nport_id is still
present.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In cases of remote-port-side cable pull/replug, there happens to be a
target that upon replug will send the port a PLOGI, a PRLI, and a LOGO.
When this sequence is received by the driver, the PLOGI accepted and a
GFT_ID is issued to find the protocol support for the remote port. While
the GFT_ID is outstanding, a LOGO is received. The driver logs the remote
port out and unregisters the RPI and schedules a new PLOGI transmission.
However, the GFT_ID was not terminated. When it completed, the driver
attempted to transition the remote port to PRLI transmission, which cancels
the PLOGI scheduling. The PRLI transmit attempt is rejected by the adapter
as the remote port is not logged in. No retry is attempted as it's expected
the logout is noted and the supposedly scheduled PLOGI should address the
state. As there is no PLOGI, the remote port does not get re-discovered.
Fix by aborting the outstanding GFT_ID if the related remote port is logged
out.
Ensure a PRLI transmit attempt only occurs if the remote port is logging
in. This avoids the incorrect attempt while logged out.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter is reset while there are outstanding ELS's, subsequent
reinitialization of the adapter will fail as it has not recovered all of
the io contexts relative to the ELS's.
If an ELS timed out or otherwise failed and an the ELS was attempted to be
aborted (which changes the ELS completion context), in causes where the
driver generates completions for the outstanding IO as the adapter would
not due to being reset, the driver released only the ELS context and failed
to release the abort context. When the adapter went to reinit, as it had
not received all of the contexts, it failed to reinit.
Fix by having the ELS completion handler identify the driver-generated
completion status and release the abort context.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unusually high IO latency can be observed with little IO in progress. The
latency may remain high regardless of amount of IO and can only be cleared
by forcing lpfc_fcp_imax values to non-zero and then back to zero.
The driver's eq_delay mechanism that scales the interrupt coalescing based
on io completion load failed to reduce or turn off coalescing when load
decreased. Specifically, if no io completed on a cpu within an eq_delay
polling window, the eq delay processing was skipped and no change was made
to the coalescing values. This left the coalescing values set when they
were no longer applicable.
Fix by always clearing the percpu counters for each time period and always
run the eq_delay calculations if an eq has a non-zero coalescing value.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a timer routine uses workqueues, it could fire before the workqueue is
allocated.
Fix by allocating the workqueue before the timer routines are setup
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After seeing some interoperability issues with ADISC, it was determined the
ELS definitions in lpfc were using types that allowed the compiler to add
pad to the structure, causing the structure to no longer be per spec. The
offending structures are ADISC, FAN, and RNID.
This patch implements the simple fix of eliminating the pad by forcing the
compiler to pack the structure. Care was taken to ensure field accesses
won't be by operations that would hit a bad field alignment.
The better solution would be to convert to the uapi fc header definitions,
but the number of changes required to do is rather intrusive so this course
of action was deferred.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When connected to a high number of remote ports, the driver is encountering
PLOGI errors. The errors are due to adapter detected failures indicating
illegal field values.
Turns out the driver was prematurely clearing an RPI bitmask before waiting
for an UNREG_RPI mailbox completion. This allowed the RPI to be reused
before it was actually available.
Fix by clearing RPI bitmask only after UNREG_RPI mailbox completion.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi-mq operation inherently performs pre-allocation of resources for
blk-mq request queues. Even though the kdump environment reduces the
configuration to a single CPU, thus 1 hardware queue, which helps
significantly, the resources are still rather large due to the per request
allocations. blk-mq pre-allocations can be over 4KB per request. With
adapter can_queue values in the 4k or 8k range, this can easily be 32MBs
before any other driver memory is factored in. Driver SGL DMA buffer
allocation can be up to 8KB per request as well adding an additional
64MB. Totals are well over 100MB for a single shost. Given kdump memory
auto-sizing utilities don't accommodate this amount of memory well, it's
very possible for kdump to fail due to lack of memory.
Fix by having the driver recognize that it is booting within a kdump
context and reduce the number of requests it will support to a more
reasonable value.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As dma_pool_destroy and mempool_destroy functions has NULL check. We may
not need NULL check before calling them.
Fix below warnings reported by coccicheck
./drivers/scsi/lpfc/lpfc_mem.c:252:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:255:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:258:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:261:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:265:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:269:2-17: WARNING: NULL check before some
freeing functions is not needed.
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When SCSI-MQ is enabled, the SCSI-MQ layers will do pre-allocation of MQ
resources based on shost values set by the driver. In newer cases of the
driver, which attempts to set nr_hw_queues to the cpu count, the
multipliers become excessive, with a single shost having SCSI-MQ
pre-allocation reaching into the multiple GBytes range. NPIV, which
creates additional shosts, only multiply this overhead. On lower-memory
systems, this can exhaust system memory very quickly, resulting in a system
crash or failures in the driver or elsewhere due to low memory conditions.
After testing several scenarios, the situation can be mitigated by limiting
the value set in shost->nr_hw_queues to 4. Although the shost values were
changed, the driver still had per-cpu hardware queues of its own that
allowed parallelization per-cpu. Testing revealed that even with the
smallish number for nr_hw_queues for SCSI-MQ, performance levels remained
near maximum with the within-driver affiinitization.
A module parameter was created to allow the value set for the nr_hw_queues
to be tunable.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As spin_unlock_irq will enable interrupts.
Function lpfc_findnode_rpi is called from
lpfc_sli_abts_err_handler (./drivers/scsi/lpfc/lpfc_sli.c)
<- lpfc_sli_async_event_handler
<- lpfc_sli_process_unsol_iocb
<- lpfc_sli_handle_fast_ring_event
<- lpfc_sli_fp_intr_handler
<- lpfc_sli_intr_handler
and lpfc_sli_intr_handler is an interrupt handler.
Interrupts are enabled in interrupt handler. Use
spin_lock_irqsave/spin_unlock_irqrestore instead of spin_(un)lock_irq in
IRQ context to avoid this.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the redundant initialization code.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a configurations runs with a single cpu (such as a kdump kernel),
which causes the driver to request a single vector, when the driver
subsequently requests an irq affinity mask, the mask comes back null. The
driver currently does nothing in this scenario, which leaves mappings to
hardware queues incomplete and crashes the system.
Fix by recognizing the null mask and assigning the vector to the first cpu
in the system.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A null check before a kfree is redundant, so remove it. This is detected
by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the final round of mostly small fixes in our initial submit.
It's mostly minor fixes and driver updates. The only change of note
is adding a virt_boundary_mask to the SCSI host and host template to
parametrise this for NVMe devices instead of having them do a call in
slave_alloc. It's a fairly straightforward conversion except in the
two NVMe handling drivers that didn't set it who now have a virtual
infinity parameter added.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXTJS/yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQTNAQCsTdkA
IN1BvDBbE+KO8mvL5DuRxLtnDU6Pq5K6fkrE3gD/a1GkqyPPaJIuspq7fQY87DH/
o7VsJd/5uGphIE2Ls+M=
=38XV
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is the final round of mostly small fixes in our initial submit.
It's mostly minor fixes and driver updates. The only change of note is
adding a virt_boundary_mask to the SCSI host and host template to
parametrise this for NVMe devices instead of having them do a call in
slave_alloc. It's a fairly straightforward conversion except in the
two NVMe handling drivers that didn't set it who now have a virtual
infinity parameter added"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: megaraid_sas: set an unlimited max_segment_size
scsi: mpt3sas: set an unlimited max_segment_size for SAS 3.0 HBAs
scsi: IB/srp: set virt_boundary_mask in the scsi host
scsi: IB/iser: set virt_boundary_mask in the scsi host
scsi: storvsc: set virt_boundary_mask in the scsi host template
scsi: ufshcd: set max_segment_size in the scsi host template
scsi: core: take the DMA max mapping size into account
scsi: core: add a host / host template field for the virt boundary
scsi: core: Fix race on creating sense cache
scsi: sd_zbc: Fix compilation warning
scsi: libfc: fix null pointer dereference on a null lport
scsi: zfcp: fix GCC compiler warning emitted with -Wmaybe-uninitialized
scsi: zfcp: fix request object use-after-free in send path causing wrong traces
scsi: zfcp: fix request object use-after-free in send path causing seqno errors
scsi: megaraid_sas: Update driver version to 07.710.50.00
scsi: megaraid_sas: Add module parameter for FW Async event logging
scsi: megaraid_sas: Enable msix_load_balance for Invader and later controllers
scsi: megaraid_sas: Fix calculation of target ID
scsi: lpfc: reduce stack size with CONFIG_GCC_PLUGIN_STRUCTLEAK_VERBOSE
scsi: devinfo: BLIST_TRY_VPD_PAGES for SanDisk Cruzer Blade
...
Merge updates from Andrew Morton:
"Am experimenting with splitting MM up into identifiable subsystems
perhaps with a view to gitifying it in complex ways. Also with more
verbose "incoming" emails.
Most of MM is here and a few other trees.
Subsystems affected by this patch series:
- hotfixes
- iommu
- scripts
- arch/sh
- ocfs2
- mm:slab-generic
- mm:slub
- mm:kmemleak
- mm:kasan
- mm:cleanups
- mm:debug
- mm:pagecache
- mm:swap
- mm:memcg
- mm:gup
- mm:pagemap
- mm:infrastructure
- mm:vmalloc
- mm:initialization
- mm:pagealloc
- mm:vmscan
- mm:tools
- mm:proc
- mm:ras
- mm:oom-kill
hotfixes:
mm: vmscan: scan anonymous pages on file refaults
mm/nvdimm: add is_ioremap_addr and use that to check ioremap address
mm/memcontrol: fix wrong statistics in memory.stat
mm/z3fold.c: lock z3fold page before __SetPageMovable()
nilfs2: do not use unexported cpu_to_le32()/le32_to_cpu() in uapi header
MAINTAINERS: nilfs2: update email address
iommu:
include/linux/dmar.h: replace single-char identifiers in macros
scripts:
scripts/decode_stacktrace: match basepath using shell prefix operator, not regex
scripts/decode_stacktrace: look for modules with .ko.debug extension
scripts/spelling.txt: drop "sepc" from the misspelling list
scripts/spelling.txt: add spelling fix for prohibited
scripts/decode_stacktrace: Accept dash/underscore in modules
scripts/spelling.txt: add more spellings to spelling.txt
arch/sh:
arch/sh/configs/sdk7786_defconfig: remove CONFIG_LOGFS
sh: config: remove left-over BACKLIGHT_LCD_SUPPORT
sh: prevent warnings when using iounmap
ocfs2:
fs: ocfs: fix spelling mistake "hearbeating" -> "heartbeat"
ocfs2/dlm: use struct_size() helper
ocfs2: add last unlock times in locking_state
ocfs2: add locking filter debugfs file
ocfs2: add first lock wait time in locking_state
ocfs: no need to check return value of debugfs_create functions
fs/ocfs2/dlmglue.c: unneeded variable: "status"
ocfs2: use kmemdup rather than duplicating its implementation
mm:slab-generic:
Patch series "mm/slab: Improved sanity checking":
mm/slab: validate cache membership under freelist hardening
mm/slab: sanity-check page type when looking up cache
lkdtm/heap: add tests for freelist hardening
mm:slub:
mm/slub.c: avoid double string traverse in kmem_cache_flags()
slub: don't panic for memcg kmem cache creation failure
mm:kmemleak:
mm/kmemleak.c: fix check for softirq context
mm/kmemleak.c: change error at _write when kmemleak is disabled
docs: kmemleak: add more documentation details
mm:kasan:
mm/kasan: print frame description for stack bugs
Patch series "Bitops instrumentation for KASAN", v5:
lib/test_kasan: add bitops tests
x86: use static_cpu_has in uaccess region to avoid instrumentation
asm-generic, x86: add bitops instrumentation for KASAN
Patch series "mm/kasan: Add object validation in ksize()", v3:
mm/kasan: introduce __kasan_check_{read,write}
mm/kasan: change kasan_check_{read,write} to return boolean
lib/test_kasan: Add test for double-kzfree detection
mm/slab: refactor common ksize KASAN logic into slab_common.c
mm/kasan: add object validation in ksize()
mm:cleanups:
include/linux/pfn_t.h: remove pfn_t_to_virt()
Patch series "remove ARCH_SELECT_MEMORY_MODEL where it has no effect":
arm: remove ARCH_SELECT_MEMORY_MODEL
s390: remove ARCH_SELECT_MEMORY_MODEL
sparc: remove ARCH_SELECT_MEMORY_MODEL
mm/gup.c: make follow_page_mask() static
mm/memory.c: trivial clean up in insert_page()
mm: make !CONFIG_HUGE_PAGE wrappers into static inlines
include/linux/mm_types.h: ifdef struct vm_area_struct::swap_readahead_info
mm: remove the account_page_dirtied export
mm/page_isolation.c: change the prototype of undo_isolate_page_range()
include/linux/vmpressure.h: use spinlock_t instead of struct spinlock
mm: remove the exporting of totalram_pages
include/linux/pagemap.h: document trylock_page() return value
mm:debug:
mm/failslab.c: by default, do not fail allocations with direct reclaim only
Patch series "debug_pagealloc improvements":
mm, debug_pagelloc: use static keys to enable debugging
mm, page_alloc: more extensive free page checking with debug_pagealloc
mm, debug_pagealloc: use a page type instead of page_ext flag
mm:pagecache:
Patch series "fix filler_t callback type mismatches", v2:
mm/filemap.c: fix an overly long line in read_cache_page
mm/filemap: don't cast ->readpage to filler_t for do_read_cache_page
jffs2: pass the correct prototype to read_cache_page
9p: pass the correct prototype to read_cache_page
mm/filemap.c: correct the comment about VM_FAULT_RETRY
mm:swap:
mm, swap: fix race between swapoff and some swap operations
mm/swap_state.c: simplify total_swapcache_pages() with get_swap_device()
mm, swap: use rbtree for swap_extent
mm/mincore.c: fix race between swapoff and mincore
mm:memcg:
memcg, oom: no oom-kill for __GFP_RETRY_MAYFAIL
memcg, fsnotify: no oom-kill for remote memcg charging
mm, memcg: introduce memory.events.local
mm: memcontrol: dump memory.stat during cgroup OOM
Patch series "mm: reparent slab memory on cgroup removal", v7:
mm: memcg/slab: postpone kmem_cache memcg pointer initialization to memcg_link_cache()
mm: memcg/slab: rename slab delayed deactivation functions and fields
mm: memcg/slab: generalize postponed non-root kmem_cache deactivation
mm: memcg/slab: introduce __memcg_kmem_uncharge_memcg()
mm: memcg/slab: unify SLAB and SLUB page accounting
mm: memcg/slab: don't check the dying flag on kmem_cache creation
mm: memcg/slab: synchronize access to kmem_cache dying flag using a spinlock
mm: memcg/slab: rework non-root kmem_cache lifecycle management
mm: memcg/slab: stop setting page->mem_cgroup pointer for slab pages
mm: memcg/slab: reparent memcg kmem_caches on cgroup removal
mm, memcg: add a memcg_slabinfo debugfs file
mm:gup:
Patch series "switch the remaining architectures to use generic GUP", v4:
mm: use untagged_addr() for get_user_pages_fast addresses
mm: simplify gup_fast_permitted
mm: lift the x86_32 PAE version of gup_get_pte to common code
MIPS: use the generic get_user_pages_fast code
sh: add the missing pud_page definition
sh: use the generic get_user_pages_fast code
sparc64: add the missing pgd_page definition
sparc64: define untagged_addr()
sparc64: use the generic get_user_pages_fast code
mm: rename CONFIG_HAVE_GENERIC_GUP to CONFIG_HAVE_FAST_GUP
mm: reorder code blocks in gup.c
mm: consolidate the get_user_pages* implementations
mm: validate get_user_pages_fast flags
mm: move the powerpc hugepd code to mm/gup.c
mm: switch gup_hugepte to use try_get_compound_head
mm: mark the page referenced in gup_hugepte
mm/gup: speed up check_and_migrate_cma_pages() on huge page
mm/gup.c: remove some BUG_ONs from get_gate_page()
mm/gup.c: mark undo_dev_pagemap as __maybe_unused
mm:pagemap:
asm-generic, x86: introduce generic pte_{alloc,free}_one[_kernel]
alpha: switch to generic version of pte allocation
arm: switch to generic version of pte allocation
arm64: switch to generic version of pte allocation
csky: switch to generic version of pte allocation
m68k: sun3: switch to generic version of pte allocation
mips: switch to generic version of pte allocation
nds32: switch to generic version of pte allocation
nios2: switch to generic version of pte allocation
parisc: switch to generic version of pte allocation
riscv: switch to generic version of pte allocation
um: switch to generic version of pte allocation
unicore32: switch to generic version of pte allocation
mm/pgtable: drop pgtable_t variable from pte_fn_t functions
mm/memory.c: fail when offset == num in first check of __vm_map_pages()
mm:infrastructure:
mm/mmu_notifier: use hlist_add_head_rcu()
mm:vmalloc:
Patch series "Some cleanups for the KVA/vmalloc", v5:
mm/vmalloc.c: remove "node" argument
mm/vmalloc.c: preload a CPU with one object for split purpose
mm/vmalloc.c: get rid of one single unlink_va() when merge
mm/vmalloc.c: switch to WARN_ON() and move it under unlink_va()
mm/vmalloc.c: spelling> s/informaion/information/
mm:initialization:
mm/large system hash: use vmalloc for size > MAX_ORDER when !hashdist
mm/large system hash: clear hashdist when only one node with memory is booted
mm:pagealloc:
arm64: move jump_label_init() before parse_early_param()
Patch series "add init_on_alloc/init_on_free boot options", v10:
mm: security: introduce init_on_alloc=1 and init_on_free=1 boot options
mm: init: report memory auto-initialization features at boot time
mm:vmscan:
mm: vmscan: remove double slab pressure by inc'ing sc->nr_scanned
mm: vmscan: correct some vmscan counters for THP swapout
mm:tools:
tools/vm/slabinfo: order command line options
tools/vm/slabinfo: add partial slab listing to -X
tools/vm/slabinfo: add option to sort by partial slabs
tools/vm/slabinfo: add sorting info to help menu
mm:proc:
proc: use down_read_killable mmap_sem for /proc/pid/maps
proc: use down_read_killable mmap_sem for /proc/pid/smaps_rollup
proc: use down_read_killable mmap_sem for /proc/pid/pagemap
proc: use down_read_killable mmap_sem for /proc/pid/clear_refs
proc: use down_read_killable mmap_sem for /proc/pid/map_files
mm: use down_read_killable for locking mmap_sem in access_remote_vm
mm: smaps: split PSS into components
mm: vmalloc: show number of vmalloc pages in /proc/meminfo
mm:ras:
mm/memory-failure.c: clarify error message
mm:oom-kill:
mm: memcontrol: use CSS_TASK_ITER_PROCS at mem_cgroup_scan_tasks()
mm, oom: refactor dump_tasks for memcg OOMs
mm, oom: remove redundant task_in_mem_cgroup() check
oom: decouple mems_allowed from oom_unkillable_task
mm/oom_kill.c: remove redundant OOM score normalization in select_bad_process()"
* akpm: (147 commits)
mm/oom_kill.c: remove redundant OOM score normalization in select_bad_process()
oom: decouple mems_allowed from oom_unkillable_task
mm, oom: remove redundant task_in_mem_cgroup() check
mm, oom: refactor dump_tasks for memcg OOMs
mm: memcontrol: use CSS_TASK_ITER_PROCS at mem_cgroup_scan_tasks()
mm/memory-failure.c: clarify error message
mm: vmalloc: show number of vmalloc pages in /proc/meminfo
mm: smaps: split PSS into components
mm: use down_read_killable for locking mmap_sem in access_remote_vm
proc: use down_read_killable mmap_sem for /proc/pid/map_files
proc: use down_read_killable mmap_sem for /proc/pid/clear_refs
proc: use down_read_killable mmap_sem for /proc/pid/pagemap
proc: use down_read_killable mmap_sem for /proc/pid/smaps_rollup
proc: use down_read_killable mmap_sem for /proc/pid/maps
tools/vm/slabinfo: add sorting info to help menu
tools/vm/slabinfo: add option to sort by partial slabs
tools/vm/slabinfo: add partial slab listing to -X
tools/vm/slabinfo: order command line options
mm: vmscan: correct some vmscan counters for THP swapout
mm: vmscan: remove double slab pressure by inc'ing sc->nr_scanned
...
The RISC-V architecture has a register named the "Supervisor Exception
Program Counter", or "sepc". This abbreviation triggers checkpatch.pl's
misspelling detector, resulting in noise in the checkpatch output. The
risk that this noise could cause more useful warnings to be missed seems
to outweigh the harm of an occasional misspelling of "spec". Thus drop
the "sepc" entry from the misspelling list.
[akpm@linux-foundation.org: fix existing "sepc" instances, per Joe]
Link: http://lkml.kernel.org/r/20190518210037.13674-1-paul.walmsley@sifive.com
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lpfc_debug_dump_all_queues() function repeatedly calls into
lpfc_debug_dump_qe() which has a temporary 128 byte buffer. This was fine
before the introduction of CONFIG_GCC_PLUGIN_STRUCTLEAK_VERBOSE because
each instance could occupy the same stack slot. However, now they each get
their own copy, which leads to a huge increase in stack usage as seen from
the compiler warning:
drivers/scsi/lpfc/lpfc_debugfs.c: In function 'lpfc_debug_dump_all_queues':
drivers/scsi/lpfc/lpfc_debugfs.c:6474:1: error: the frame size of 1712 bytes is larger than 100 bytes [-Werror=frame-larger-than=]
Avoid this by not marking lpfc_debug_dump_qe() as inline so the compiler
can choose to emit a static version of this function when it's needed or
otherwise silently drop it. As an added benefit, not inlining multiple
copies of this function means we save several kilobytes of .text section,
reducing the file size from 47kb to 43.
It is somewhat unusual to have a function that is static but not inline in
a header file, but this does not cause problems here because it is only
used by other inline functions. It would however seem reasonable to move
all the lpfc_debug_dump_* functions into lpfc_debugfs.c and not mark them
inline as a later cleanup.
Fixes: 81a56f6dcd ("gcc-plugins: structleak: Generalize to all variable types")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This topic branch covers a fundamental change in how our sg lists are
allocated to make mq more efficient by reducing the size of the
preallocated sg list. This necessitates a large number of driver
changes because the previous guarantee that if a driver specified
SG_ALL as the size of its scatter list, it would get a non-chained
list and didn't need to bother with scatterlist iterators is now
broken and every driver *must* use scatterlist iterators.
This was broken out as a separate topic because we need to convert all
the drivers before pulling the trigger and unconverted drivers kept
being found, necessitating a rebase.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTzzCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishZB+AP9I8j/s
wWfg0Z3WNuf4D5I3rH4x1J3cQTqPJed+RjwgcQEA1gZvtOTg1ZEn/CYMVnaB92x0
t6MZSchIaFXeqfD+E7U=
=cv8o
-----END PGP SIGNATURE-----
Merge tag 'scsi-sg' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI scatter-gather list updates from James Bottomley:
"This topic branch covers a fundamental change in how our sg lists are
allocated to make mq more efficient by reducing the size of the
preallocated sg list.
This necessitates a large number of driver changes because the
previous guarantee that if a driver specified SG_ALL as the size of
its scatter list, it would get a non-chained list and didn't need to
bother with scatterlist iterators is now broken and every driver
*must* use scatterlist iterators.
This was broken out as a separate topic because we need to convert all
the drivers before pulling the trigger and unconverted drivers kept
being found, necessitating a rebase"
* tag 'scsi-sg' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
scsi: core: don't preallocate small SGL in case of NO_SG_CHAIN
scsi: lib/sg_pool.c: clear 'first_chunk' in case of no preallocation
scsi: core: avoid preallocating big SGL for data
scsi: core: avoid preallocating big SGL for protection information
scsi: lib/sg_pool.c: improve APIs for allocating sg pool
scsi: esp: use sg helper to iterate over scatterlist
scsi: NCR5380: use sg helper to iterate over scatterlist
scsi: wd33c93: use sg helper to iterate over scatterlist
scsi: ppa: use sg helper to iterate over scatterlist
scsi: pcmcia: nsp_cs: use sg helper to iterate over scatterlist
scsi: imm: use sg helper to iterate over scatterlist
scsi: aha152x: use sg helper to iterate over scatterlist
scsi: s390: zfcp_fc: use sg helper to iterate over scatterlist
scsi: staging: unisys: visorhba: use sg helper to iterate over scatterlist
scsi: usb: image: microtek: use sg helper to iterate over scatterlist
scsi: pmcraid: use sg helper to iterate over scatterlist
scsi: ipr: use sg helper to iterate over scatterlist
scsi: mvumi: use sg helper to iterate over scatterlist
scsi: lpfc: use sg helper to iterate over scatterlist
scsi: advansys: use sg helper to iterate over scatterlist
...
This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTl4yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdcxAQDCJVbd
fPUX76/V1ldupunF97+3DTharxxbst+VnkOnCwD8D4c0KFFFOI9+F36cnMGCPegE
fjy17dQLvsJ4GsidHy8=
=aS5B
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
The big merge conflict this time around is the SPDX licence tags.
Following discussion on linux-next, we believe our version to be more
accurate than the one in the tree, so the resolution is to take our
version for all the SPDX conflicts"
Note on the SPDX license tag conversion conflicts: the SCSI tree had
done its own SPDX conversion, which in some cases conflicted with the
treewide ones done by Thomas & co.
In almost all cases, the conflicts were purely syntactic: the SCSI tree
used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the
treewide conversion had used the new-style ones ("GPL-2.0-only" and
"GPL-2.0-or-later").
In these cases I picked the new-style one.
In a few cases, the SPDX conversion was actually different, though. As
explained by James above, and in more detail in a pre-pull-request
thread:
"The other problem is actually substantive: In the libsas code Luben
Tuikov originally specified gpl 2.0 only by dint of stating:
* This file is licensed under GPLv2.
In all the libsas files, but then muddied the water by quoting GPLv2
verbatim (which includes the or later than language). So for these
files Christoph did the conversion to v2 only SPDX tags and Thomas
converted to v2 or later tags"
So in those cases, where the spdx tag substantially mattered, I took the
SCSI tree conversion of it, but then also took the opportunity to turn
the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag.
Similarly, when there were whitespace differences or other differences
to the comments around the copyright notices, I took the version from
the SCSI tree as being the more specific conversion.
Finally, in the spdx conversions that had no conflicts (because the
treewide ones hadn't been done for those files), I just took the SCSI
tree version as-is, even if it was old-style. The old-style conversions
are perfectly valid, even if the "-only" and "-or-later" versions are
perhaps more descriptive.
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits)
scsi: qla2xxx: move IO flush to the front of NVME rport unregistration
scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition
scsi: qla2xxx: on session delete, return nvme cmd
scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices
scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1
scsi: megaraid_sas: Introduce various Aero performance modes
scsi: megaraid_sas: Use high IOPS queues based on IO workload
scsi: megaraid_sas: Set affinity for high IOPS reply queues
scsi: megaraid_sas: Enable coalescing for high IOPS queues
scsi: megaraid_sas: Add support for High IOPS queues
scsi: megaraid_sas: Add support for MPI toolbox commands
scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver
scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura
scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD
scsi: megaraid_sas: Handle sequence JBOD map failure at driver level
scsi: megaraid_sas: Don't send FPIO to RL Bypass queue
scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault
scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout
scsi: megaraid_sas: Call disable_irq from process IRQ poll
scsi: megaraid_sas: Remove few debug counters from IO path
...
To support scenarios which aren't bound to nvmetcli add port scenarios,
which is currently where the nvmet_fc transport invokes the discovery
event callbacks, a syfs attribute is added to lpfc which can be written
to cause an RSCN to be generated for the nport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch updates RSCN receive processing to check for the remote
port being an NVME port, and if so, invoke the nvme_fc callback to
rescan the remote port. The rescan will generate a discovery udev
event.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds support for the nvmet discovery op. When the callback
routine is called, the driver will call the routine to generate an RSCN
to the port on the other end of the link.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds general RSCN support:
- The ability to transmit an RSCN to the port on the other end of
the link (regular port if pt2pt, or fabric controller if fabric).
- And general recognition of an RSCN ELS when an ELS is received.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message]
Reviewed by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When building powerpc pseries_defconfig or powernv_defconfig:
drivers/scsi/lpfc/lpfc_nvmet.c:224:1: error: unused function
'lpfc_nvmet_get_ctx_for_xri' [-Werror,-Wunused-function]
drivers/scsi/lpfc/lpfc_nvmet.c:246:1: error: unused function
'lpfc_nvmet_get_ctx_for_oxid' [-Werror,-Wunused-function]
These functions are only compiled when CONFIG_NVME_TARGET_FC is enabled.
Use that same condition so there is no more warning. While the fixes commit
did not introduce these functions, it caused these warnings.
Fixes: 4064b27417a7 ("scsi: lpfc: Make some symbols static")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warnings:
drivers/scsi/lpfc/lpfc_sli.c:115:1: warning: symbol 'lpfc_sli4_pcimem_bcopy' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_sli.c:7854:1: warning: symbol 'lpfc_sli4_process_missed_mbox_completions' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:223:27: warning: symbol 'lpfc_nvmet_get_ctx_for_xri' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_nvmet.c:245:27: warning: symbol 'lpfc_nvmet_get_ctx_for_oxid' was not declared. Should it be static?
drivers/scsi/lpfc/lpfc_init.c:75:10: warning: symbol 'lpfc_present_cpu' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/scsi/lpfc/lpfc_init.c: In function lpfc_setup_cq_lookup:
drivers/scsi/lpfc/lpfc_init.c:9359:30: warning: variable qp set but not used [-Wunused-but-set-variable]
It's not used since commit e70596a60f88 ("scsi: lpfc: Fix poor use of
hardware queues if fewer irq vectors")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use *_pool_zalloc rather than *_pool_alloc followed by memset with 0.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.2.0.3
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kernel warnings may be seen with preempt debugging enabled.
Replace smp_processor_id calls with raw_smp_processor_id or cpu information
stored in hdwq structures.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Crashes in scsi_queue_rq or in dma_unmap_direct_sg during BFS when lpfc has
lpfc_enable_bg=1.
lpfc is setting DIX and prot sg after scsi_add_host_with_dma() has been
called. The scsi_host_set_prot() and scsi_host_set_guard() routines need to
be called before scsi_add_host_with_dma().
Revise the calling sequence to set the protection/guard data before calling
scsi_add_host_with_dma().
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FDMI protocol support registration was not accurately showing nvme
support. The fcponly-path clears the parameter object.
Move the code out of the fcponly code path. Fix the FDMI registration data
to properly check for nvme support. Commonize the manner in which the fdmi
routines set protocol support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issuing a LUN reset was resulting in a command failure which then escalated
to a host reset.
The FCP-4 spec allows fcp_rsp_len field to specify the number of valid
bytes of FCP_RSP_INFO, and the value could be 4 or 8. The driver is
allowing only a value of 8, thus it failed the command.
Revise the driver to allow 4 or 8.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While fixing the resources per socket, realized the driver was not using
hardware queues (up to 1 per cpu) if there were fewer interrupt
vectors. The driver was only using the hardware queue assigned to the cpu
with the vector.
Rework the affinity map check to use the additional hardware queue elements
that had been allocated. If the cpu count exceeds the hardware queue count
- share, but choose what is shared with by: hyperthread peer, core peer,
socket peer, or finally similar cpu in a different socket.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver was coded expecting enough hardware queues and interrupt vectors
such that at least there was one per socket. In the case where there were
fewer than sockets, cpus were left unassigned thus null pointers.
Rework the affinity mappings. Map settings for the cpu's that are in the
irq cpu mask. For each cpu not in the mask, map to another cpu that does
have a mask. Choice of the "other" cpu will attempt to map to the same cpu
but differing hyperthread, or cpu within in same core, or cpu within same
socket, or finally cpu in the base socket.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Invalid logical speed is displayed for trunk enabled ports when all ports
are down. Also noted that link speed is incorrectly reported for the units
when links are up.
Current code is returning the logical link speed from the last event from
the adapter. In cases where the last link went down, the link speed in the
event was not valid - meaning that although the links where down the field
had a bogus value.
Rework the event handling to qualify the trunk link state before using the
event speed data.
Also correct units on other areas where the logical link speed was taken
from a link event.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
eq create is leaking mailbox memory if it encounters an error.
rework error path to free the memory.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver unconditionally says fw doesn't support nvme when in
truth it was a driver parameter settings that disabled nvme support.
Rework the code validating nvme support to accurately report what
condition is disabling nvme support. Save state on whether nvme
fw supports nvme in case sysfs attributes change dynamically.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a race condition with the abort handler declaring a waitq
item on it's stack, followed by a timeout in the abort handler that
has it give up on the abort return to its caller. When the io is
finally aborted and its completion handler called, it references
the waitq element that the abort_handler set up, which is no longer
valid resulting in a deadlock.
Fix by clearing the waitq reference, under lock, when the abort
handler timeout gives up. Have the completion handler validate the
waitq before referencing it.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When queued work is executed posting a new command to the transport
the driver is reporting a null buffer.
The driver had received an ABTS which matched a command that had
been scheduled for delivery to the transport. The driver proceeded
to cancel the command, but the work item was never cancelled.
Fix by cancelling the queued work item. Also turns out the ABTS
response was not properly sending a BA_ACC, so set the flag to
send the ACC.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use-after-free memory overwrite detected. Problem reported
by Ewan Milne at Red Hat after running lpfc target with additional
memory checking enabled.
Race condition when lpfc_nvmet_xmt_ls_rsp_cmp frees the ctxp
memory in interrupt context before lpfc_nvmet_xmt_ls_rsp
clears a field in the ctxp after successfully issuing the wqe.
Remove the unnecessary ctxp write after reposting the rq buffer. The
ctxp->rqb_buffer field is not checked in LS handling after the wqe
is submitted.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reported-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under heavy load the target stops responding, the drivers aborts
timeout and we start recovery by logging out of the target, but
the target is never logged into again.
In a point-to-point scenario, there were battling PLOGI's. When we
received a PLOGI request after having sent one, the driver cancels
the processing of the original plogi. However, the completion path
of the remaining plogi was coded to skip the reg_rpi that should
be happening on the 2nd plogi.
Correct by adding a simple pt2pt check such that the 2nd plogi isn't
skipped and the reg_login occurs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Turns out the message change in 12.2.0.1 for unsupported topology
makes the linux driver out of sync with other products.
Revert the message back to the prior content for product consistency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver currently is relying on firmware to match ABTSs to existing
exchanges. This works fine as long as an exchange has been assigned to the
io and work posted to it. However, for unmapped frames (rxid=0xFFFF), the
driver has yet to assign an xri. The driver was blindly saying it couldn't
match the ABTS and sending the BA_xxx. However, the command frame may have
been in queues waiting on xri's before posting to the nvmet_fc layer. When
xri's became available, the command frame would still be pushed to the
transport and that io would execute, even though the io had been killed by
ABTS. The initiator, seeing the io ABTS'd, would reuse the exchange for a
different io which would be received on the target and pushed up. If the
"zombie" io then came back down and started transmitting, the initiator
would match the oxid and accept erroneous data. Bad things happened.
Add tracking of active exchanges in the target to allow matching of a
received ABTS against active or pending IO requests. If the ABTS is matched
to a pending or active IO, the drive initiates cleanup and conditionally
notifies the transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver is notified of new command frame receipt by CQEs. As
part of the CQE processing, the driver upcalls the nvmet_fc transport to
deliver the command. nvmet_fc, as part of receiving the command builds out
a context for it, where one of the first steps is to allocate memory for
the io.
When running with tests that do large ios (1MB), it was found on some
systems, the total number of outstanding I/O's, at 1MB per, completely
consumed the system's memory. Thus additional ios were getting blocked in
the memory allocator. Given that this blocked the lpfc thread processing
CQEs, there were lots of other commands that were received and which are
then held up, and given CQEs are serially processed, the aggregate delays
for an IO waiting behind the others became cummulative - enough so that the
initiator hit timeouts for the ios.
The basic fix is to avoid the direct upcall and instead schedule a work
item for each io as it is received. This allows the cq processing to
complete very quickly, and each io can then run or block on it's own.
However, this general solution hurts latency when there are few ios. As
such, implemented the fix such that the driver watches how many CQEs it has
processed sequentially in one run. As long as the count is below a
threshold, the direct nvmet_fc upcall will be made. Only when the count is
exceeded will it revert to work scheduling.
Given that debug of this showed a surprisingly long delay in cq processing,
the io timer stats were updated to better reflect the processing of the
different points.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise a stalled adapter message to also include the number of jobs that
are stalling the thread.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A race condition resulted in receive buffers being placed in the free list
twice.
Change the locking and handling to check whether the "other" path will be
freeing the entry in a later thread and skip it if it is.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After receiving an unsolicited ABTS (meaning rxid is 0xFFFF), the driver
used the oxid from the initiator to match against a local xri which may
have been allocated for the io. The xri would be the rxid - it's an invalid
check resulting in the command not being matched or erroneously matched.
Change the lookup to use the oxid and the SID to match against received
IO's original values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Softlockups are seen in low memory situations. They are due to doing
oas_lun allocation with GFP_KERNEL in atomic contexts.
Change the calls to oas_lun to indicate atomic context so that GFP_ATOMIC
is used.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due to the couple of bug fixes, update lpfc version to 12.2.0.2
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There was a missing qualification of a valid ndlp structure when calling to
send an RRQ for an abort. Add the check.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many of the exit cases were not releasing the rcu read lock. Corrected the
exit paths.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There were a number of erroneous comments and incorrect older lockdep
checks that were causing a number of warnings.
Resolve the following:
- Inconsistent lock state warnings in lpfc_nvme_info_show().
- Fixed comments and code on sequences where ring lock is now held instead
of hbalock.
- Reworked calling sequences around lpfc_sli_iocbq_lookup(). Rather than
locking prior to the routine and have routine guess on what lock, take
the lock within the routine. The lockdep check becomes unnecessary.
- Fixed comments and removed erroneous hbalock checks.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Bart Van Assche <bvanassche@acm.org>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warning:
drivers/scsi/lpfc/lpfc_init.c:13091:1: warning:
symbol 'lpfc_sli4_oas_verify' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We have a few submissions for 5.2 that depend on fixes merged post
5.1-rc1. Merge the fixes branch into queue.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the FC-NVMe driver is leverating the SCSI FC transport class to
access the remote ports. Which means that all FC-NVMe remote ports will be
visible to the fc transport layer, but due to missing definitions the port
roles will always be 'unknown'. This patch adds the missing definitions to
the fc transport class to that the port roles are correctly displayed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Giridhar Malavali <gmalavali@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support to recognize FPIN ELS's that are received. When
one is received, the fc transport will be called to handle the the FPIN.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the following compiler warning is reported with
CONFIG_NVME_FC=n:
drivers/scsi/lpfc/lpfc_nvme.c:2140:1: warning: 'lpfc_nvme_lport_unreg_wait' defined but not used [-Wunused-function]
lpfc_nvme_lport_unreg_wait(struct lpfc_vport *vport,
^~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 3999df75bc ("scsi: lpfc: Declare local functions static")
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Abort thread wakeups, on some wqe types, are not happening. The thread
wakeup logic is dependent upon the LPFC_DRIVER_ABORTED flag. However, on
these wqes, the completion handler running prior to the io completion
routine ends up clearing the flag.
Rework the wakeup logic to look at a non-null waitq element which must be
set if the abort thread is waiting. This is reverting the change in the
indicated patch.
Fixes: c2017260ee ("scsi: lpfc: Rework locking on SCSI io completion")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that a kernel warning appears when smp_processor_id() is
called with preempt debugging enabled.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove those functions that are not called from outside the removed
functions.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality but avoids that the compiler
complains about set-but-not-used variables when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arrays should be defined in .c files instead of in a header file. This
patch reduces the size of the lpfc kernel module.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler warns about missing fall-through
annotation when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoid that smatch complains about misleading indentation.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler complains about missing declarations
when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
clang -Wuninitialized incorrectly sees a variable being used without
initialization:
drivers/scsi/lpfc/lpfc_nvme.c:2102:37: error: variable 'localport' is uninitialized when used here
[-Werror,-Wuninitialized]
lport = (struct lpfc_nvme_lport *)localport->private;
^~~~~~~~~
drivers/scsi/lpfc/lpfc_nvme.c:2059:38: note: initialize the variable 'localport' to silence this warning
struct nvme_fc_local_port *localport;
^
= NULL
1 error generated.
This is clearly in dead code, as the condition leading up to it is always
false when CONFIG_NVME_FC is disabled, and the variable is always
initialized when nvme_fc_register_localport() got called successfully.
Change the preprocessor conditional to the equivalent C construct, which
makes the code more readable and gets rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.
1) Uses of size += snprintf(buf, SIZE - size, fmt, ...)
In this case, if snprintf would have written more characters than what the
buffer size (SIZE) is, then size will end up larger than SIZE. In later
uses of snprintf, SIZE - size will result in a negative number, leading
to problems. Note that size might already be too large by using
size = snprintf before the code reaches a case of size += snprintf.
2) If size is ultimately used as a length parameter for a copy back to user
space, then it will potentially allow for a buffer overflow and information
disclosure when size is greater than SIZE. When the size is used to index
the buffer directly, we can have memory corruption. This also means when
size = snprintf... is used, it may also cause problems since size may become
large. Copying to userspace is mitigated by the HARDENED_USERCOPY kernel
configuration.
The solution to these issues is to use scnprintf which returns the number of
characters actually written to the buffer, so the size variable will never
exceed SIZE.
Signed-off-by: Silvio Cesare <silvio.cesare@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Declaring interrupt clear routines as inline is bogus as they are used as
an indirect pointer.
Remove the inline references.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
You can't declare a function inline in a header if it doesn't have a body
available to the compiler. So realistically you either don't declare it
inline or you make it a static inline in the header. I think the latter
applies in this case, so this should be the fix
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.2.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise driver copyright message to show 2019. Update couple of files
modified by 12.2.0.1 patch set.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the 6072 log message string to print the whole 32 bits of the
extended status.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver had duplicated log message numbers making debug difficult.
Make all messages unique.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change the SLI4 queue creation code to use NUMA node based memory
allocation based on the cpu the queues will be related to.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver maintains a sideband structure which has a pointer for
each queue element. However, at 8 bytes per pointer, and up to 4k elements
per queue, and 100s of queues, this can take up a lot of memory.
Convert the driver to using an access routine that calculates the element
address based on its index rather than using the pointer table.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When in trunking mode, the adapter can be placed into diagnostic mode and
each link in the trunk tested via loopback.
Add support to the driver to perform per-link loopback testing when in
trunking mode.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is using uint16_t and is encountering an overflow of the 16bits when
calculating link speed.
Fix by using a u32 type.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If all the trunk links drop and a single link resumes, the link_state is
not properly reported. When trunked, the driver receives two async
cqes. One acqe reports the trunk link states, which the driver records.
The other cqe reports the overall state of the trunk. In the failing case,
the trunk link state acqe preceeds the overall trunk link state acqe. The
trunk link state acqe, as it's an "up" transition, calls a code path which
ensures a down transition before moving to the up state. The down
transition had a side effect of clearing the just-saved trunk link states.
Fix by not clearing the trunk link states if we've already transitioned
to a down state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Invalid test is allowing Loop to be a supported topology on G6 and G7
adapters. The chips do not support loop as their link speeds prohibit loop
per standard.
Correct the conditional so that loop is not reported.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently reporting the firmware revision not the actual boot
bios version in FDMI data.
Modify the driver to obtain the boot bios version from the adapter and use
that data in the FMDI data sent to the switch.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The switch is rejecting FDMI2 registration for symbolic name. There is a
"\n" in the name string, which the switch dislikes thus rejects the
registration.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is reporting support for NVME even when not configured for NVME
operation.
Fix (and make more readable) when NVME protocol support is indicated.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The FDMI manufacturer value being reported on Linux is inconsistent with
other OS's.
Set the value to "Emulex Corporation" for consistency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the driver undergoes repeated host resets it starts losing exchange
structures and eventually returns SCSI_MLQUEUE_HOST_BUSY and does not
recover. The offline path is not reclaiming the outstanding ios on the fcp
pring txcmplq before calling lpfc_destroy_multixripool, which causes the
txmcplq to be reinit and the resources lost.
Flush the fcp rings before destroying the multixripools.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The adapter initialization sequence enables interrupts, initializes the
adapter link_state to LINK_DOWN, then issues commands to initialize the
adapter. The interrupt handler on the adapter validates the link_state (has
to be at least LINK_DOWN) and if invalid, will discard the interrupting
event.
In most cases, there is not a command completion, thus an interrupt until
the initialization commands have been sent which is post the setting of
state to LINK_DOWN. However, in cases of firmware reset, the reset will
modify the link_state to an invalid value (indicating a reset of the
adapter) and there occasionally are cases where the adapter will generate
an asynchronous event which shares the eq/cq used for mailbox commands. In
the failure case, an interrupt is generated immediately after enabling them
due to the async event. As link_state is invalid, the eq is list and the
CQ not serviced. At this point link_state is initialized and the mailbox
command sent. As the CQ has not been serviced, it is not armed, so no
interrupt event is generated when the mailbox command completes.
Modify the initialization sequence so that interrupts are enabled after
link_state is properly initialized, which avoids the race condition with
the async event.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's possible for the scsi error handler to fire and call the target reset
handler simultaneously to the driver logging out and relogging into the
system. If hit just right, the re-login may not have fully re-established
the remote port and the rdata->pnod structure may be null.
Check for NULL in the reset handler and return failure if NULL.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code incorrectly specifies a completion wait timeout duration in 5
jiffies, when it should have been 5 seconds.
Fix the adjust for units for the completion timeout call.
[mkp: manual merge]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code is using msleep when polling for hw ready. Unfortunately the
msleep routine isn't very accurate on rescheduling. In fact, on a busy
systems which reset the adapter, it became 10s of seconds before it was
rescheduled.
Fix by busy waiting using udelay. As we're now busy waiting, significantly
reduce the wait time so that we can exit the pool loop as soon as possible.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver periodically checks for adapter error in a background thread. If
the thread detects an error, the adapter will be reset including the
deletion and reallocation of workqueues on the adapter. Simultaneously,
there may be a user-space request to offline the adapter which may try to
do many of the same steps, in parallel, on a different thread. As memory
was deallocated while unexpected, the parallel offline request hit a bad
pointer.
Add coordination between the two threads. The error recovery thread has
precedence. So, when an error is detected, a flag is set on the adapter to
indicate the error thread is terminating the adapter. But, before doing
that work, it will look for a flag that is set by the offline flow, and if
set, will wait for it to complete before then processing the error handling
path. Similarly, in the offline thread, it first checks for whether the
error thread is resetting the adapter, and if so, will then wait for the
error thread to finish. Only after it has finished, will it set its flag
and offline the adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a couple of cases, the driver detected a pci error (via pci device state
or via failed register reads) but didn't take any action to disable the
device. Additionally, the driver is ignoring the status of pci
configuration space reads.
Having the driver take the adapter offline whenever the pci error is
detected. Pay attention to pci_config_space_read status and return failure
if an error is seen.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an adapter fails, causing a board reset, the board reset routine
lpfc_hba_down_s4() takes the hbalock out then calls
lpfc_nvmet_ctxbuf_post() who then tries to take out the same lock. As the
context lists are now protected under the buf_list_locks, there is no need
for the hbalock to be held by the board reset routine.
Fix by no longer taking the hbalock in the board reset routine.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With negative test injection, the driver is receiving a command with first
burst enabled, meaning Sequence initiative is not passed with the command
frame. The driver notes the condition and discards the frame. However the
driver calls the incorrect buffer free routine, resulting in a NULL pointer
reference.
For hbq buffer free, convert to using lpfc_rq_buf_free().
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, when lpfc_nvmet_mrq is 0 it could mean 2 different things
depending on when its looked at. If at module load time it specifies the
default number of hardware queues to allocate, with 0 meaning default to
the number of CPUs. But post module load, a value of zero means to disable
mrq use.
Changed the driver so that enablement of mrq is based on whether nvme
target mode is enabled or not. When enabled, mrq is enabled. Thus, the
cfg_nvemt_mrq field only specifies the number of mrq queues to enable, with
0 defaulting to the number of cpus.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under circustances with high load, the driver is running out of async
receive buffers which may result in one of the following messages:
0:6401 RQE Error x13, posted 226 err_cnt 0: 925c6050 925c604e 925c5d54
or
0:2885 Port Status Event: port status reg 0x81800000,
port smphr reg 0xc000, error 1=0x52004a01, error 2=0x0
The driver is waiting for full io completion before returning receive
buffers to the adapter. There is no need for such a relationship.
Whenever a new command is received from the wire, the driver will have two
contexts - an io context (ctxp) and a receive buffer context. In current
code, the receive buffer context stays 1:1 with the io and won't be
reposted to the hardware until the io completes. There is no need for such
a relationship.
Change the driver so that up on successful handing of the command to the
transport, where the transport has copied what it needed thus the buffer is
returned to the driver, have the driver immediately repost the buffer to
the hardware. If the command cannot be successfully handed to the transport
as transport resources are temporarily busy, have the driver allocate a new
and separate receive buffer and post it to the hardware so that hardware
can continue while the command is queued for the transport.
When an io is complete, the transport returns the io context to the driver,
and the driver may be waiting for more contexts, thus immediately reuse the
io context. In this path, there was a buffer posted when the receive buffer
was queued waiting for an io context so a replacement is not needed in the
new code additions. Thus, exempt this the context reuse case from the
buffer reposting.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The debug ktime counters that trace an io were inadvertently not placed in
the common section of an io buffer. Thus, they generate an invalid opcode
error when accessed.
Move the ktime counters into the common area.
Fixes: 0794d601d1 ("scsi: lpfc: Implement common IO buffers between NVME and SCSI")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During debug, it was seen that the driver is issuing commands specific to
SLI3 on SLI4 devices. Although the adapter correctly rejected the command,
this should not be done.
Revise the code to stop sending these commands on a SLI4 adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When unloading the driver, mailbox commands may be sent without holding a
reference on the ndlp. By the time the mailbox command completes, the ndlp
may have reduced its ref counts and been freed. The problem was reported
by KASAN.
While unregistering due to driver unload, have the completion noop'd by
setting the ndlp context NULL'd. Due to the unload, no further action was
necessary. Also, while reviewing this path, the generic nulling of the
context after handling should be slightly moved.
Reported by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A patch in the 12.2.0.0 set caused a new lockdep warning:
WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
5.0.0-rc8-next-20190301-dbg+ #1 Not tainted
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(&qp->io_buf_list_put_lock)->rlock);
local_irq_disable();
lock(&(&phba->hbalock)->rlock);
lock(&(&qp->io_buf_list_put_lock)->rlock);
<Interrupt>
lock(&(&phba->hbalock)->rlock);
see: https://www.spinics.net/lists/linux-scsi/msg128389.html
In summary, the new patch added taking the io_buf_list_put_lock while under
an irq-disabled hbalock. This created a lock heirarchy dependent upon irq
being disabled, and there are paths that take the io_buf_list_put_lock
without disabling irq.
Looking at the lpfc_io_free routine, which is where the new heirarchy was
introduced, there is no reason to be taking out the hbalock and raising
irq, as the functionality is replaced by the io_buf_list_xxx locks.
Resolve by removing the hbalock/irq calls in lpfc_io_free.
Fixes: 5e5b511d8b ("scsi: lpfc: Partition XRI buffer list across Hardware Queues")
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A prior patch which added support for non-uniform allocation of MSIX
vectors now causes a smatch complaint:
drivers/scsi/lpfc/lpfc_scsi.c:3674 lpfc_scsi_cmd_iocb_cmpl()
error: we previously assumed 'phba->sli4_hba.hdwq' could be
null (see line 3667)
Resolve by removing the unnecessary check for a NULL hdwq table.
Fixes 6a828b0f61: ("scsi: lpfc: Support non-uniform allocation of MSIX vectors to hardware queues")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the final round of mostly small fixes and performance
improvements to our initial submit. The main regression fix is the
ia64 simscsi build failure which was missed in the serial number
elimination conversion.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIxBayYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisherpAP4rxLpX
bcUnQnEsvoxys/JyoK08Qfv1JebZo1B2MAZ62wD/VZ7LpOuzVLhsM2KhLFGRrs1/
7D2K4tgtO2dQsFix7H0=
=pcHl
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the final round of mostly small fixes and performance
improvements to our initial submit.
The main regression fix is the ia64 simscsi build failure which was
missed in the serial number elimination conversion"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: ia64: simscsi: use request tag instead of serial_number
scsi: aacraid: Fix performance issue on logical drives
scsi: lpfc: Fix error codes in lpfc_sli4_pci_mem_setup()
scsi: libiscsi: Hold back_lock when calling iscsi_complete_task
scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of HiLink
scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP target port
scsi: hisi_sas: Set PHY linkrate when disconnected
scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw
scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
scsi: qla2xxx: check for kstrtol() failure
scsi: lpfc: fix 32-bit format string warning
scsi: lpfc: fix unused variable warning
scsi: target: tcmu: Switch to bitmap_zalloc()
scsi: libiscsi: fall back to sendmsg for slab pages
scsi: qla2xxx: avoid printf format warning
scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset
scsi: lpfc: Correct __lpfc_sli_issue_iocb_s4 lockdep check
scsi: ufs: hisi: fix ufs_hba_variant_ops passing
scsi: qla2xxx: Fix panic in qla_dfs_tgt_counters_show
...
It used to be that "error" was set to -ENODEV at the start of the function
but we shifted some code around an now "error" is set to zero for most
error paths. There is a mix of direct returns and "goto out" but I changed
everything to direct returns for consistency.
Fixes: 56de835704 ("scsi: lpfc: fix calls to dma_set_mask_and_coherent()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core. Additionally Christoph
refactored gdth as part of the dma changes. The major mid-layer
change this time is the removal of bidi commands and with them the
whole of the osd/exofs driver and filesystem.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
f69LpXGmMpuagKGvvd4=
=Fhy1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
On 32-bit architectures, we see a warning when %ld is used to print a
size_t:
In file included from drivers/scsi/lpfc/lpfc_init.c:62:
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_new_io_buf':
drivers/scsi/lpfc/lpfc_logmsg.h:62:45: error: format '%ld' expects argument of type 'long int', but argument 5 has type 'unsigned int' [-Werror=format=]
This is harmless, but portable code should just use %zd to avoid the
warning.
Fixes: 0794d601d1 ("scsi: lpfc: Implement common IO buffers between NVME and SCSI")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The newly introduced 'cpu' variable is only used inside of an optional
block, so we get a warning without CONFIG_SCSI_LPFC_DEBUG_FS:
drivers/scsi/lpfc/lpfc_nvme.c: In function 'lpfc_nvme_io_cmd_wqe_cmpl':
drivers/scsi/lpfc/lpfc_nvme.c:968:30: error: unused variable 'cpu' [-Werror=unused-variable]
uint32_t code, status, idx, cpu;
Move the declaration into the same block to avoid the warning.
Fixes: 63df6d637e ("scsi: lpfc: Adapt cpucheck debugfs logic to Hardware Queues")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The patch that replaced io channels for hdw_queues now reports the
following static checker warning:
drivers/scsi/lpfc/lpfc_init.c:11136 lpfc_sli4_hba_unset()
error: we previously assumed 'phba->pport' could be null (see line 11074)
Resolve by adding a pport NULL check.
[mkp: tag tweak]
Fixes: cdb42becdd ("scsi: lpfc: Replace io_channels for nvme and fcp with general hdw_queues per cpu"_
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The outer routine lpfc_sli_issue_iocb(), which decomposes into the
SLI3 (s3) or SLI4 (s4) subroutines takes out the locks. For s3, it takes
out the hbalock. For s4, it takes out the ring_lock. The lockdep check in
the s3 and s4 subroutines both check hbalock, which is incorrect for s4.
Revise the s4 subroutine to lockdep check the ring_lock.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nine small fixes. The resume fix is a cosmetic removal of a warning
with an incorrect condition causing it to alarm people wrongly. The
other eight patches correct a thinko in Christoph Hellwig's DMA
conversion series. Without it all these drivers end up with 32 bit
DMA masks meaning they bounce any page over 4GB before sending it to
the controller. Nowadays, even laptops mostly have memory above 4GB,
so this can lead to significant performance degradation with all the
bouncing.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXHql8CYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQmvAQCSVQRf
kx3ABDGnaj4Km4/Jzibj44aCYwh+ewwtLCWwFQD9GWaEaDxBkbxQDf/YndQKRhYg
VJQjjj6a9VlNSmWoW28=
=L9Fe
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine small fixes.
The resume fix is a cosmetic removal of a warning with an incorrect
condition causing it to alarm people wrongly.
The other eight patches correct a thinko in Christoph Hellwig's DMA
conversion series. Without it all these drivers end up with 32 bit DMA
masks meaning they bounce any page over 4GB before sending it to the
controller.
Nowadays, even laptops mostly have memory above 4GB, so this can lead
to significant performance degradation with all the bouncing"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: Avoid that system resume triggers a kernel warning
scsi: hptiop: fix calls to dma_set_mask()
scsi: hisi_sas: fix calls to dma_set_mask_and_coherent()
scsi: csiostor: fix calls to dma_set_mask_and_coherent()
scsi: bfa: fix calls to dma_set_mask_and_coherent()
scsi: aic94xx: fix calls to dma_set_mask_and_coherent()
scsi: 3w-sas: fix calls to dma_set_mask_and_coherent()
scsi: 3w-9xxx: fix calls to dma_set_mask_and_coherent()
scsi: lpfc: fix calls to dma_set_mask_and_coherent()
The change to use dma_set_mask_and_coherent() incorrectly made a second
call with the 32 bit DMA mask value when the call with the 64 bit DMA mask
value succeeded. This resulted in NVMe/FC connections failing due to
corrupted data buffers, and various other SCSI/FCP I/O errors.
Fixes: f30e1bfd61 ("scsi: lpfc: use dma_set_mask_and_coherent")
Cc: <stable@vger.kernel.org>
Suggested-by: Don Dutile <ddutile@redhat.com>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_cpu_affinity_check':
drivers/scsi/lpfc/lpfc_init.c:10599:19: warning:
variable 'phys_id' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit 6a828b0f61 ("scsi: lpfc:
Support non-uniform allocation of MSIX vectors to hardware queues")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are a handful of statements that are indented incorrectly. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This should return -ENOMEM if kcalloc() fails, but it accidentally
returns success instead.
Fixes: 6a828b0f61 ("scsi: lpfc: Support non-uniform allocation of MSIX vectors to hardware queues")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.2.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For files modified as part of 12.2.0.0 patches, update copyright to 2019
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Various null pointer dereference and general protection fault panics occur
when there is a link bounce under load. There are a large number of "error"
message 6413 indicating "bad release".
The issues resolve to list corruptions due to missing or inconsistent lock
protection. Lockups are due to nested locks in the unsolicited abort
path. The unsolicited abort path calls the wrong abort processing
routine. There was also duplicate context release while aborts were still
active in the hardware.
Removed duplicate locks and added lock protection around list item
removal. Commonized lock handling around the abort processing routines.
Prevent context release while still in ABTS list.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the transport calls into the lpfc target to release an IO job
structure, which corresponds to an exchange, and if the driver was waiting
for an exchange in order to post a previously received command to the
transport, the driver immediately takes the IO job and reuses the context
for the prior command and calls nvmet_fc_rcv_fcp_req() to tell the
transport about a newly received command.
Problem is, the execution of the IO job release may be in the context of
the back end driver and its bio completion handlers, thus it may be in a
irq context and protection code kicks in in the bio and request layers that
are subsequently called.
Rework lpfc so that instead of immediately upcalling, queue it to a
deferred work thread and have the thread make the upcall.
Took advantage of this change to remove duplicated code with the normal
command receive path that preps the IO job and upcalls nvmet_fc. Created a
common routine both paths use.
Also corrected some errors that were found during review of the context
freeing and reuse - basically unlocked operations and a somewhat disjoint
set of calls to release associated job elements. Cleaned up this path and
added locks for coherency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The conversion to enable SCSI and NVME fc4 support ran into an issue with
NPIV support. With NVME, NPIV is not currently supported, but with SCSI it
was. The driver reverted to its lowest setting meaning NPIV with SCSI was
not allowed.
Convert the NPIV checks and implementation so that SCSI can continue to
allow NPIV support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A scsi host lock is taken on every io completion to check whether the abort
handler is waiting on the io completion. This is an expensive lock to take
on all completion when rarely in an abort condition.
Replace scsi host lock with command-specific lock. Synchronize completion
and abort paths by new cmd lock. Ensure all flag changing and nulling of
context pointers taken under lock. When adding lock to task management
abort, realized it was missing other synchronization locks. Added that
synchronization to match normal paths.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that performance mods don't split resources by protocol and enable both
protocols by default, there's no reason not to enable concurrent SCSI and
NVME fc4 support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The work done to date utilized the number of present cpus when sizing
per-cpu structures. Structures should have been sized based on the max
possible cpu count.
Convert the driver over to possible cpu count for sizing allocation.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current driver uses the older IRQ API for MSIX allocation
Change driver to utilize pci_alloc_irq_vectors when allocating IRQ vectors.
Make lpfc_cpu_affinity_check use pci_irq_get_affinity to determine how the
kernel mapped all the IRQs.
Remove msix_entries from SLI4 structure, replaced with pci_irq_vector()
usage.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driving high iop counts, auto_imax coalescing kicks in and drives the
performance to extremely small iops levels.
There are two issues:
1) auto_imax is enabled by default. The auto algorithm, when iops gets
high, divides the iops by the hdwq count and uses that value to
calculate EQ_Delay. The EQ_Delay is set uniformly on all EQs whether
they have load or not. The EQ_delay is only manipulated every 5s (a
long time). Thus there were large 5s swings of no interrupt delay
followed by large/maximum delay, before repeating.
2) When processing a CQ, the driver got mixed up on the rate of when
to ring the doorbell to keep the chip appraised of the eqe or cqe
consumption as well as how how long to sit in the thread and
process queue entries. Currently, the driver capped its work at
64 entries (very small) and exited/rearmed the CQ. Thus, on heavy
loads, additional overheads were taken to exit and re-enter the
interrupt handler. Worse, if in the large/maximum coalescing
windows,k it could be a while before getting back to servicing.
The issues are corrected by the following:
- A change in defaults. Auto_imax is turned OFF and fcp_imax is set
to 0. Thus all interrupts are immediate.
- Cleanup of field names and their meanings. Existing names were
non-intuitive or used for duplicate things.
- Added max_proc_limit field, to control the length of time the
handlers would service completions.
- Reworked EQ handling:
Added common routine that walks eq, applying notify interval and max
processing limits. Use queue_claimed to claim ownership of the queue
while processing. Always rearm the queue whenever the common routine
is called.
Rework queue element processing, namely to eliminate hba_index vs
host_index. Only one index is necessary. The queue entry can be
marked invalid and the host_index updated immediately after eqe
processing.
After rework, xx_release routines are now DB write functions. Renamed
the routines as such.
Moved lpfc_sli4_eq_flush(), which does similar action, to same area.
Replaced the 2 individual loops that walk an eq with a call to the
common routine.
Slightly revised lpfc_sli4_hba_handle_eqe() calling syntax.
Added per-cpu counters to detect interrupt rates and scale
interrupt coalescing values.
- Reworked CQ handling:
Added common routine that walks cq, applying notify interval and max
processing limits. Use queue_claimed to claim ownership of the queue
while processing. Always rearm the queue whenever the common routine
is called.
Rework queue element processing, namely to eliminate hba_index vs
host_index. Only one index is necessary. The queue entry can be
marked invalid and the host_index updated immediately after cqe
processing.
After rework, xx_release routines are now DB write functions. Renamed
the routines as such.
Replaced the 3 individual loops that walk a cq with a call to the
common routine.
Redefined lpfc_sli4_sp_handle_mcqe() to commong handler definition with
queue reference. Add increment for mbox completion to handler.
- Added a new module/sysfs attribute: lpfc_cq_max_proc_limit To allow
dynamic changing of the CQ max_proc_limit value being used.
Although this leaves an EQ as an immediate interrupt, that interrupt will
only occur if a CQ bound to it is in an armed state and has cqe's to
process. By staying in the cq processing routine longer, high loads will
avoid generating more interrupts as they will only rearm as the processing
thread exits. The immediately interrupt is also beneficial to idle or
lower-processing CQ's as they get serviced immediately without being
penalized by sharing an EQ with a more loaded CQ.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Review of the eq coalescing logic showed the code was a bit fragmented.
Sometimes it would save/set via an interrupt max value, while in others it
would do so via a usdelay. There were also two places changing eq delay,
one place that issued mailbox commands, and another that changed via
register writes if supported.
Clean this up by:
- Standardizing the operation of lpfc_modify_hba_eq_delay() routine so
that it is always told of a us delay to impose. The routine then chooses
the best way to set that - via register or via mbx.
- Rather than two value types stored in eq->q_mode (usdelay if change via
register, imax if change via mbox) - q_mode always contains usdelay.
Before any value change, old vs new value is compared and only if
different is a change done.
- Revised the dmult calculation. dmult is not set based on overall imax
divided by hardware queues - instead imax applies to a single cpu and
the value will be replicated to all cpus.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
So far MSIX vector allocation assumed it would be 1:1 with hardware
queues. However, there are several reasons why fewer MSIX vectors may be
allocated than hardware queues such as the platform being out of vectors or
adapter limits being less than cpu count.
This patch reworks the MSIX/EQ relationships with the per-cpu hardware
queues so they can function independently. MSIX vectors will be equitably
split been cpu sockets/cores and then the per-cpu hardware queues will be
mapped to the vectors most efficient for them.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The desired affinity for the hardware queue behavior is for hdwq 0 to be
affinitized with cpu 0, hdwq 1 to cpu 1, and so on. The implementation so
far does not do this if the number of cpus is greater than the number of
hardware queues (e.g. hardware queue allocation was administratively
reduced or hardware queue resources could not scale to the cpu count).
Correct the queue affinitization logic when queue count is less than
cpu count.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Default behavior is to use the information from the upper IO stacks to
select the hardware queue to use for IO submission. Which typically has
good cpu affinity.
However, the driver, when used on some variants of the upstream kernel, has
found queuing information to be suboptimal for FCP or IO completion locked
on particular cpus.
For command submission situations, the lpfc_fcp_io_sched module parameter
can be set to specify a hardware queue selection policy that overrides the
os stack information.
For IO completion situations, rather than queing cq processing based on the
cpu servicing the interrupting event, schedule the cq processing on the cpu
associated with the hardware queue's cq.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The XRI get/put lists were partitioned per hardware queue. However, the
adapter rarely had sufficient resources to give a large number of resources
per queue. As such, it became common for a cpu to encounter a lack of XRI
resource and request the upper io stack to retry after returning a BUSY
condition. This occurred even though other cpus were idle and not using
their resources.
Create as efficient a scheme as possible to move resources to the cpus that
need them. Each cpu maintains a small private pool which it allocates from
for io. There is a watermark that the cpu attempts to keep in the private
pool. The private pool, when empty, pulls from a global pool from the
cpu. When the cpu's global pool is empty it will pull from other cpu's
global pool. As there many cpu global pools (1 per cpu or hardware queue
count) and as each cpu selects what cpu to pull from at different rates and
at different times, it creates a radomizing effect that minimizes the
number of cpu's that will contend with each other when the steal XRI's from
another cpu's global pool.
On io completion, a cpu will push the XRI back on to its private pool. A
watermark level is maintained for the private pool such that when it is
exceeded it will move XRI's to the CPU global pool so that other cpu's may
allocate them.
On NVME, as heartbeat commands are critical to get placed on the wire, a
single expedite pool is maintained. When a heartbeat is to be sent, it will
allocate an XRI from the expedite pool rather than the normal cpu
private/global pools. On any io completion, if a reduction in the expedite
pools is seen, it will be replenished before the XRI is placed on the cpu
private pool.
Statistics are added to aid understanding the XRI levels on each cpu and
their behaviors.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that the lower half has much better per-cpu parallelization using the
hardware queues, the SCSI MQ support needs to be tied into it.
The involves the following mods:
- Use the hardware queue info from the midlayer to help select the
hardware queue to utilize. This required change to the get_scsi-buf_xxx
routines.
- Remove lpfc_sli4_scmd_to_wqidx_distr() routine. No longer needed.
- Includes fix for SLI-3 that does not have multi queue parallelization.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SLI4 nvme functions are passing the SLI3 ring number when posting wqe to
hardware. This should be indicating the hardware queue to use, not the ring
number.
Replace ring number with the hardware queue that should be used.
Note: SCSI avoided this issue as it utilized an older lfpc_issue_iocb
routine that properly adapts.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many io statistics were being sampled and saved using adapter-based data
structures. This was creating a lot of contention and cache thrashing in
the I/O path.
Move the statistics to the hardware queue data structures. Given the
per-queue data structures, use of atomic types is lessened.
Add new sysfs and debugfs stat routines to collate the per hardware queue
values and report at an adapter level.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Similar to the io execution path that reports cpu context information, the
debugfs routines for cpu information needs to be aligned with new hardware
queue implementation.
Convert debugfs cnd nvme cpucheck statistics to report information per
Hardware Queue.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Both NVME and SCSI aborts are now processed off the CQ workqueue and do not
generate events for the slowpath any more.
Remove the unused event code.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Once the IO buff allocations were made shared, there was a single XRI
buffer list shared by all hardware queues. A single list isn't great for
performance when shared across the per-cpu hardware queues.
Create a separate XRI IO buffer get/put list for each Hardware Queue. As
SGLs and associated IO buffers get allocated/posted to the firmware; round
robin their assignment across all available hardware Queues so that there
is an equitable assignment.
Modify SCSI and NVME IO submit code paths to use the Hardware Queue logic
for XRI allocation.
Add a debugfs interface to display hardware queue statistics
Added new empty_io_bufs counter to track if a cpu runs out of XRIs.
Replace common_ variables/names with io_ to make meanings clearer.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, both nvme and fcp each have their own concept of an io_channel,
which is a combination wq/cq and associated msix. Different cpus would
share an io_channel.
The driver is now moving to per-cpu wq/cq pairs and msix vectors. The
driver will still use separate wq/cq pairs per protocol on each cpu, but
the protocols will share the msix vector.
Given the elimination of the nvme and fcp io channels, the module
parameters will be removed. A new parameter, lpfc_hdw_queue is added which
allows the wq/cq pair allocation per cpu to be overridden and allocated to
lesser value. If lpfc_hdw_queue is zero, the number of pairs allocated will
be based on the number of cpus. If non-zero, the parameter specifies the
number of queues to allocate. At this time, the maximum non-zero value is
64.
To manage this new paradigm, a new hardware queue structure is created to
track queue activity and relationships.
As MSIX vector allocation must be known before setting up the
relationships, msix allocation now occurs before queue datastructures are
allocated. If the number of vectors allocated is less than the desired
hardware queues, the hardware queue counts will be reduced to the number of
vectors
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a extra queue and msix vector for expresslane. Now that the driver
will be doing queues per cpu, this oddball queue is no longer needed.
Expresslane will utilize the normal per-cpu queues.
Updated debugfs sli4 queue output to go along with the change
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, both NVME and SCSI get their IO buffers from separate
pools. XRI's are associated 1:1 with IO buffers, so XRI's are also split
between protocols.
Eliminate the independent pools and use a single pool. Each buffer
structure now has a common section and a protocol section. Per protocol
routines for SGL initialization are removed and replaced by common
routines. Initialization of the buffers is only done on the common area.
All other fields, which are protocol specific, are initialized when the
buffer is allocated for use in the per-protocol allocation routine.
In the past, the SCSI side allocated IO buffers as part of slave_alloc
calls until the maximum XRIs for SCSI was reached. As all XRIs are now
common and may be used for either protocol, allocation for everything is
done as part of adapter initialization and the scsi side has no action in
slave alloc.
As XRI's are no longer split, the lpfc_xri_split module parameter is
removed.
Adapters based on SLI3 will continue to use the older scsi_buf_list_get/put
routines. All SLI4 adapters utilize the new IO buffer scheme
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_nvme_prep_io_cmd() checks for null pnode, but caller
lpfc_nvme_fcp_io_submit() has already ensured it's non-null.
Remove the pnode null check.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An hba-wide lock is taken in the nvme io completion routine. The lock
covers null'ing of the nrport pointer in the cmd structure.
The nrport member isn't necessary. After extracting the pointer from the
command, the pointer was dereferenced to get the fc discovery node
pointer. But the fc discovery node pointer is alrady in the command
structure so the dereferrence was unnecessary.
Eliminated the nrport structure member and its use, which also eliminates
the port-wide lock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling debugfs functions, there is no need to ever check the return
value. The function can work or not, but the code logic should never do
something different based on this.
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Six fixes, all of which appear to have user visible consequences. The
DMA one is a regression fix from the merge window and of the others,
four are driver specific and one specific to the target code.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXEt6GSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbxoAP0R0z0J
fdCRn9AMRbZ3xJzD+E6V2gw38Gdgm8rR5mT1gQEAv1VxZwOAb9Qxbcr+l4uybqZr
Q55H31I/IvBgNm84jH0=
=vkW7
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fixes, all of which appear to have user visible consequences.
The DMA one is a regression fix from the merge window and of the
others, four are driver specific and one specific to the target code"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: Use explicit access size in ufshcd_dump_regs
scsi: tcmu: fix use after free
scsi: csiostor: fix NULL pointer dereference in csio_vport_set_state()
scsi: lpfc: nvmet: avoid hang / use-after-free when destroying targetport
scsi: lpfc: nvme: avoid hang / use-after-free when destroying localport
scsi: communicate max segment size to the DMA mapping code
We cannot wait on a completion object in the lpfc_nvme_targetport structure
in the _destroy_targetport() code path because the NVMe/fc transport will
free that structure immediately after the .targetport_delete() callback.
This results in a use-after-free, and a hang if slub_debug=FZPU is enabled.
Fix this by putting the completion on the stack.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We cannot wait on a completion object in the lpfc_nvme_lport structure in
the _destroy_localport() code path because the NVMe/fc transport will free
that structure immediately after the .localport_delete() callback. This
results in a use-after-free, and a hang if slub_debug=FZPU is enabled.
Fix this by putting the completion on the stack.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A set of 17 fixes. Most of these are minor or trivial. The one fix
that may be serious is the isci one: the bug can cause hba parameters
to be set from uninitialized memory. I don't think it's exploitable,
but you never know.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXEKL0SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishVZpAQCwuPTk
fqOt4v4hJ0oUHtEBsQK3VMXSdUvWdb5Lbn3WeQD/RFYTyNxcIF7ADSWw71b+IigT
ejUrMzI8ig+nZ1jbFZ4=
=BdS/
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A set of 17 fixes. Most of these are minor or trivial.
The one fix that may be serious is the isci one: the bug can cause hba
parameters to be set from uninitialized memory. I don't think it's
exploitable, but you never know"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxgb4i: add wait_for_completion()
scsi: qla1280: set 64bit coherent mask
scsi: ufs: Fix geometry descriptor size
scsi: megaraid_sas: Retry reads of outbound_intr_status reg
scsi: qedi: Add ep_state for login completion on un-reachable targets
scsi: ufs: Fix system suspend status
scsi: qla2xxx: Use correct number of vectors for online CPUs
scsi: hisi_sas: Set protection parameters prior to adding SCSI host
scsi: tcmu: avoid cmd/qfull timers updated whenever a new cmd comes
scsi: isci: initialize shost fully before calling scsi_add_host()
scsi: lpfc: lpfc_sli: Mark expected switch fall-throughs
scsi: smartpqi_init: fix boolean expression in pqi_device_remove_start
scsi: core: Synchronize request queue PM status only on successful resume
scsi: pm80xx: reduce indentation
scsi: qla4xxx: check return code of qla4xxx_copy_from_fwddb_param
scsi: megaraid_sas: correct an info message
scsi: target/iscsi: fix error msg typo when create lio_qr_cache failed
scsi: sd: Fix cache_type_store()
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "Drop thru" and "Fall
Thru" with "fall through" annotations, which is what GCC is expecting to
find.
Also, in some cases a dash is added as a token in order to separate the
"fall through" annotation from the rest of the comment on the same line,
which is what GCC is expecting to find.
Addresses-Coverity-ID: 114979 ("Missing break in switch")
Addresses-Coverity-ID: 114980 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas. Additionally, we have
a pile of annotation, unused variable and minor updates. The big API
change is the updates for Christoph's DMA rework which include
removing the DISABLE_CLUSTERING flag. And finally there are a couple
of target tree updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXCEUNiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdjKAP9vrTTv
qFaYmAoRSbPq9ZiixaXLMy0K/6o76Uay0gnBqgD/fgn3jg/KQ6alNaCjmfeV3wAj
u1j3H7tha9j1it+4pUw=
=GDa+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas.
Additionally, we have a pile of annotation, unused variable and minor
updates.
The big API change is the updates for Christoph's DMA rework which
include removing the DISABLE_CLUSTERING flag.
And finally there are a couple of target tree updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (259 commits)
scsi: isci: request: mark expected switch fall-through
scsi: isci: remote_node_context: mark expected switch fall-throughs
scsi: isci: remote_device: Mark expected switch fall-throughs
scsi: isci: phy: Mark expected switch fall-through
scsi: iscsi: Capture iscsi debug messages using tracepoints
scsi: myrb: Mark expected switch fall-throughs
scsi: megaraid: fix out-of-bound array accesses
scsi: mpt3sas: mpt3sas_scsih: Mark expected switch fall-through
scsi: fcoe: remove set but not used variable 'port'
scsi: smartpqi: call pqi_free_interrupts() in pqi_shutdown()
scsi: smartpqi: fix build warnings
scsi: smartpqi: update driver version
scsi: smartpqi: add ofa support
scsi: smartpqi: increase fw status register read timeout
scsi: smartpqi: bump driver version
scsi: smartpqi: add smp_utils support
scsi: smartpqi: correct lun reset issues
scsi: smartpqi: correct volume status
scsi: smartpqi: do not offline disks for transient did no connect conditions
scsi: smartpqi: allow for larger raid maps
...
Update lpfc version to 12.0.0.10
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds a "pci_bus_reset" option to the board_mode sysfs attribute.
This option uses the pci_reset_bus() api to reset the PCIe link the adapter
is on, which will reset the chip/adapter. Prior to issuing this option,
all functions on the same chip must be placed in the offline state by the
admin. After the reset, all of the instances may be brought online again.
The primary purpose of this functionality is to support cases where
firmware update required a chip reset but the admin did not want to reboot
the machine in order to instantiate the firmware update.
Sanity checks take place prior to the reset to ensure the adapter is the
sole entity on the PCIe bus and that all functions are in the offline
state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current messages report generic actions (like send GID_FT), but misses
reporting for what protocol type the action is taken.
Revise the messages to reflect the FC4 protocol type being worked on.
[mkp: typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a target's link dropped, an RSCN was received to communicate the
change. The driver detected the loss of the target and issued and UNREG_RPI
mailbox command. While that was being processed, another RSCN was received
to communicate the port coming back. The driver deferred the PLOGI to the
port until the mailbox command finishes. When the mailbox command completed
it saw the pending port and called the routines to issue the
PLOGI. However, it forgot to clear the UNREG_INP state flag, so the PLOGI
xmt routine nooped the PLOGI request assuming it needed to wait for the
mailbox command. At this point, login would never be re-attempted.
Clear UNREG_INP before issuing the deferred PLOGI.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, when a trunk link goes down due to some fault, the driver
snapshots the fault code. If the link then comes back up, meaning there is
no fault, the driver is not clearing the fault code so the sysfs link_state
entry reports old/stale data.
Revise the logic so that on successful link up the fault code is cleared.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The existing MDS loopback diagnostics support processing received frames in
the slowpath work thread. It caps the number of frames it will process at
64, before waiting for another event to indicate additional frame
reception. The net-net is this results in very slow frame processing during
loopback tests and sometimes orphans an io, causing the loopback test to
report failure by the switch.
Move MDS loopback frame processing out of the slow path worker thread and
into the normal RQ processing routines.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter is taken offline, the trunk link port attributes continue to
report trunk links as up even though all links are down as the adapter is
offline.
Clear the trunk links state as part of taking the adapter offline.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Certain older adapters such as the OneConnect OCe10100 may not have a valid
wqpcnt value. In this case, do not set queue->page_count to 0 in
lpfc_sli4_queue_alloc() as this will prevent the driver from initializing.
Fixes: 895427bd01 ("scsi: lpfc: NVME Initiator: Base modifications")
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page. Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addition of support for if_type=6 missed several checks for interface type,
resulting in the failure of several key management features such as
firmware dump and loopback testing.
Correct the checks on the if_type so that both SLI4 IF_TYPE's 2 and 6 are
supported.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 287aba2592.
We killed the bad firmware and this mod is no longer necessary.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwNpb0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGwGwH/00UHnXfxww3ixxz
zwTVDzptA6SPm6s84yJOWatM5fXhPiAltZaHSYF9lzRzNU71NCq7Frhq3fQUIXKM
OxqDn9nfSTWcjWTk2q5n2keyRV/KIn67YX7UgqFc1bO/mqtVjEgNWaMyblhI+e9E
giu1ZXayHr43jK1cDOmGExZubXUq7Vsc9TOlrd+d2SwIqeEP7TCMrPhnHDwCNvX2
UU5dtANpVzGtHaBcr37wJj+L8kODCc0f+PQ3g2ar5jTHst5SLlHp2u0AMRnUmgdi
VkGx+mu/uk8mtwUqMIMqhplklVoqK6LTeLqsY5Xt32SKruw9UqyJGdphLjW2QP/g
MkmA1lI=
=7kaD
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rc6' into for-4.21/block
Pull in v4.20-rc6 to resolve the conflict in NVMe, but also to get the
two corruption fixes. We're going to be overhauling the direct dispatch
path, and we need to do that on top of the changes we made for that
in mainline.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Update the driver version to 12.0.0.9
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When dif and first burst is used in a write command wqe, the driver was not
properly setting fields in the io command request. This resulted in no dif
bytes being sent and invalid xfer_rdy's, resulting in the io being aborted
by the hardware.
Correct the wqe initializaton when both dif and first burst are used.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On driver termination, after the driver stops fw logging by writing a
register on the chip, the driver immediately unmaps and frees the logging
buffer, without confirming in any way that the chip has received the write
and terminated the logging. As termination on the chip is not immediate,
the chip may issue a dma request to the now unmapped dma buffer, resulting
in a iommu fault.
Change the driver to receive a confirmation that logging ahs been
terminated. As the driver always issues an SLI reset with the device as
part of shutdown, and as part of that is receiving confirmation that the
reset is complete - the driver was modified to perform the write to disable
fw logging prior to the SLI reset and only free the fw log buffer after the
SLI reset is complete. That guarantees use of the fw log buffer is fully
terminated when it is unmapped.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver missed classifying the chip type for G7 when reporting supported
topologies. This resulted in loop being shown as supported on FC links that
are not supported per the standard.
Add the chip classifications to the topology checks in the driver.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is setting bits in word 10 of the SLI4 ABORT WQE (the wqid). The
field was a carry over from a prior SLI revision. The field does not exist
in SLI4, and the action may result in an overlap with future definition of
the WQE.
Remove the setting of WQID in the ABORT WQE.
Also cleaned up WQE field settings - initialize to zero, don't bother to
set fields to zero.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current discovery state machine the driver treated FLOGI oddly. When
point to point, an FLOGI is to be exchanged by the two ports, with the port
with the most significant WWN then proceeding with PLOGI. The
implementation in the driver was keyed to closely with "what have I sent",
not with what has happened between the two endpoints. Thus, it blatantly
would ACC an FLOGI, but reject PLOGI's until it had its FLOGI ACC'd. The
problem is - the sending of FLOGI may be delayed for some reason, or the
response to FLOGI held off by the other side. In the failing situation the
other side sent an FLOGI, which was ACC'd, then sent PLOGIs which were then
rjt'd until the retry count for the PLOGIs were exceeded and the port gave
up. The FLOGI may have been very late in transmit, or the response held off
until the PLOGIs failed. Given the other port had the higher WWN, no PLOGIs
would occur and communication stopped.
Correct the situation by changing the FLOGI handling. Defer any response to
an FLOGI until the driver has sent its FLOGI as well. Then, upon either
completion of the sent FLOGI, or upon sending an ACC to a received FLOGI
(which may be received before or just after FLOGI was sent). the driver
will act on who has the higher WWN. if the other port does, the driver will
noop any handling of an FLOGI response (if outstanding) and wait for PLOGI.
If the local port does, the driver will transition to sending PLOGI and
will noop any action on responding to an FLOGI (if not yet received).
Fortunately, to implement this, it only took another state flag and
deferring any FLOGI response if the FLOGI has yet to be transmit. All
subsequent actions were already in place.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In some link initialization sequences, the fw generates an erroneous FLOGI
payload to the driver without an intervening link bounce. The driver, when
it sees a 2nd FLOGI without an intervening link bounce, automatically
performs a link bounce. In this, the link bounce causes the situate to
repeat and in a nasty loop of link bounces.
Resolve the issue by validating the FLOGI payload. The erroneous FLOGI will
contain VVL signatures that are not normal. When the driver sees these, it
will simply reject the flogi rather than bouncing the link. The reject is
consumed within the firmware.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Two initiator ports were cable swapped and after swap both went down. The
driver internally swaps the nlp nodes based on matching node wwn's but not
the same nport id as before. After detecting a change in the nodes RPI, the
driver sends an UNREG_RPI command and clears the NLP_RPI_REGISTERED flag,
then swaps the node information with the other node. But the other node's
NLP_RPI_REGISTERED flag is also cleared, but it is done so without an
UNREG_RPI being sent, which causes the later REG_RPI for that other node to
fail as the hardware believes its still registered.
Additionally, if the node swap occurred while the two nodes had PLOGI's in
flight, the fc4_types weren't properly getting swapped such that when the
PLOGIs commpleted and PRLI's were then sent, the PRLI's acted on bad
protocol types so the PRLI was for the wrong protocol. NVME devices saw
SCSI FCP PRLIs and vice versa.
Clean up the node swap so that the NLP_RPI_REGISTERED flag is handled
properly.
Fix the handling of the fc4_types when the nodes are swapped as well
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Depending on the chipset, the number of NPIV vports may vary and be in
excess of what most switches support (256). To avoid confusion with the
users, limit the reported NPIV vports to 256.
Additionally correct the 16G adapter which is reporting a bogus NPIV vport
number if the link is down.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver is hitting null pring pointers in lpfc_do_work().
Pointer assignment occurs based on SLI-revision. If recovering after an
error, its possible the sli revision for the port was cleared, making the
lpfc_phba_elsring() not return a ring pointer, thus the null pointer.
Add SLI revision checking to lpfc_phba_elsring() and status checking to all
callers.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Renumber one of the 0711 log messages so there isn't a duplication.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is getting hit with 100s of RSCNs during remote port address
changes. Each of those RSCN's ends up generating UNREG_RPI and REG_PRI
mailbox commands. The discovery engine within the driver doesn't wait for
the mailbox command completions. Instead it sets state flags and moves
forward. At some point, there's a massive backlog of mailbox commands which
take time for the adapter to process. Additionally, it appears there were
duplicate events from the switch so the driver generated duplicate mailbox
commands for the same remote port. During this window, failures on PLOGI
and PRLI ELS's are see as the adapter is rejecting them as they are for
remote ports that still have pending mailbox commands.
Streamline the discovery engine so that PLOGI log checks for outstanding
UNREG_RPIs and defer the processing until the commands complete. This
better synchronizes the ELS transmission vs the RPI registrations.
Filter out multiple UNREG_RPIs being queued up for the same remote port.
Beef up log messages in this area.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver data structure for managing a mailbox command contained two
context fields. Unfortunately, the context were considered "generic" to be
used at the whim of the command code. Of course, one section of code used
fields this way, while another did it that way, and eventually there were
mixups.
Refactored the structure so that the generic contexts become a node context
and a buffer context and all code standardizes on their use.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update manufacturer attribute to reflect Broadcom Inc, not Emulex
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While trying to get adapter fw-log for a function whose buffsize was set to
0, kernel panic occurred.
When buffsize is 0, the kernel buffer for the log won't be allocated. When
fw log usage was enabled, it failed to check the buffer size, and log usage
was started. Eventually the driver referenced the unallocated log buffer.
Added checks of the buffer size before allowing fw logging to be enabled
and added check for valid buffer if enabling fw log.
Performed a couple other minor cleanups while fixing this:
- clarified log messages
- re-evaluated log message severity
- treat any error as an error, not only a couple codes
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since f44ac12f1d, BG enablement is tracked with the LPFC_SLI3_BG_ENABLED
bit, which is set in lpfc_get_cfgparam before lpfc_sli_config_sli_port() is
called. The bit shouldn't be cleared before checking the feature. Based on
problem analysis by David Bond.
Fixes: f44ac12f1d "scsi: lpfc: Memory allocation error during driver start-up on power8"
Tested-by: David Bond <dbond@suse.com>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Cc: stable@vger.kernel.org # 4.17.x
Cc: stable@vger.kernel.org # 4.18.x
Cc: stable@vger.kernel.org # 4.19.x
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replaced dma_alloc_coherent + memset with dma_zalloc_coherent.
Signed-off-by: Sabyasachi Gupta <sabyasachi.linux@gmail.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlvx2sAeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGycgIAIuxobwt0RRKa0zO
ROS+34JGoC2yU2P9VdEGWdtxS6ANMVQgKPBhWL6s+xR89Kd+V4xSdJLD1pNTxxqP
0DCva0np1/Q4juH+JbU50v/lykoLgteZ0P0LBRGf1y8p3WiLPv45IbnNsMDNYhB2
7a8rOmZYakRY9CPznRDw3X8cJt3sddKgFJHIOGz1OQJVWtCD0KPGcJmQNsbDSagY
Zx6Z5BKSIdjRqaAdN5gDa1Pft3WQo7TpaQGl80lSsgr5LcjmscXA3sClOCy+25Mo
FZLx0PcwP+Efq8RTGzNK51WSOMa6d37hvjDqUAdQBOR0KbyjRyXQwyQVw/MGbPJs
7J3Pzm0=
=56Mt
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rc3' into for-4.21/block
Merge in -rc3 to resolve a few conflicts, but also to get a few
important fixes that have gone into mainline since the block
4.21 branch was forked off (most notably the SCSI queue issue,
which is both a conflict AND needed fix).
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API. Switch it over to the better generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This removes the legacy (non-mq) IO path for SCSI.
Cc: linux-scsi@vger.kernel.org
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Update the driver version to 12.0.0.8
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add trunking support to the driver. Trunking is found on more recent
asics. In general, trunking appears as a single "port" to the driver
and overall behavior doesn't differ. Link speed is reported as an
aggregate value, while link speed control is done on a per-physical
link basis with all links in the trunk symmetrical. Some commands
returning port information are updated to additionally provide
trunking information. And new ACQEs are generated to report physical
link events relative to the trunk.
This patch contains the following modifications:
- Added link speed settings of 128GB and 256GB.
- Added handling of trunk-related ACQEs, mainly logging and trapping
of physical link statuses.
- Added additional bsg interface to query trunk state by applications.
- Augment link_state sysfs attribtute to display trunk link status
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The switches seem to respond faster to GID_PT vs GID_FT NameServer
queries. Add support for GID_PT to be used over GID_FT to enable
faster storage failover detection. Includes addition of new module
parameter to select between GID_PT and GID_FT (GID_FT is default).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An address change for a remote port cause PRLI for the wrong protocol
to be sent. The node copy done in the discovery code skipped copying
the fc4 protocols supported as well.
Fix the copy logic for the address change. Beefed up log messages in
this area as well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Testing a point-to-point topology and a case of re-FLOGI without
intervening link bouncing, showed an odd interaction with firmware and
a resulting scenario where the driver no longer probed after accepting
the new FLOGI.
Work around the firmware issue by issuing a link bounce if a FLOGI is
received after the link is already up and FLOGI's accepted.
While debugging the issue, realized that some debug traces should be
clarified to help in the future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When LCB's are rejected, if beaconing was already in progress, the
Reason Code Explanation was not being set. Should have been set to
command in progress.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On FCoE adapters, when running link bounce test in a loop, initiator
failed to login with switch switch and required driver reload to
recover. Switch reached a point where all subsequent FLOGIs would be
LS_RJT'd. Further testing showed the condition to be related to not
performing FCF discovery between FLOGI's.
Fix by monitoring FLOGI failures and once a repeated error is seen
repeat FCF discovery.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
