Allow drivers to enable/disable ccwgroup devices.
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
I was chasing down a bug of random validity intercepts on s390.
(guest prefix page not mapped in the host virtual aspace). Turns out
that the problem was a wrong address space control element. The
cause was quite complex:
During paging activity a DAT protection during SIE caused a program
interrupt. Normally, the sie retry loop tries to catch all
interrupts during and shortly before sie to rerun the setup. The
problem is now that protection causes a suppressing program interrupt,
causing the PSW to point to the instruction AFTER SIE in case of DAT
protection. This confused the logic of the retry loop to not trigger,
instead we jumped directly back to SIE after return from
the program interrupt. (the protection fault handler itself did
a rewind of the psw). This usually works quite well, but:
If now the protection fault handler has to wait, another program
might be scheduled in. Later on the sie process will be schedules
in again. In that case the content of CR1 (primary address space)
will be wrong because switch_to will put the user space ASCE into CR1
and not the guest ASCE.
In addition the program parameter is also wrong for every protection
fault of a guest, since we dont issue the SPP instruction.
So lets also check for PSW == instruction after SIE in the program
check handler. Instead of expensively checking all program
interruption codes that might be suppressing we assume that a program
interrupt pointing after SIE was always a program interrupt in SIE.
(Otherwise we have a kernel bug anyway).
We also have to compensate the rewinding, since the C-level handlers
will do that. Therefore we need to add a nop with the same length
as SIE before the sie_loop.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: stable@vger.kernel.org
CC: Heiko Carstens <heiko.carstens@de.ibm.com>
The current single step code is racy in regard to concurrent delivery
of signals. If a signal is delivered after a PER program check occurred
but before the TIF_PER_TRAP bit has been checked in entry[64].S the code
clears TIF_PER_TRAP and then calls do_signal. This is wrong, if the
instruction completed (or has been suppressed) a SIGTRAP should be
delivered to the debugger in any case. Only if the instruction has been
nullified the SIGTRAP may not be send.
The new logic always sets TIF_PER_TRAP if the program check indicates PER
tracing but removes it again for all program checks that are nullifying.
The effect is that for each change in the PSW address we now get a
single SIGTRAP.
Reported-by: Andreas Arnez <arnez@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow to generate code that only runs on zEC12 machines.
Also add a check which prevents the kernel to run on machines which
do not have any of the following new facilities installed:
- (48) decimal-floating-point zoned-conversion
- (49) execution-hint
- (49) load-and-trap
- (49) miscellaneous-instruction-extensions
- (49) processor-assist
- (50) constrained transactional-execution
- (73) transactional-execution
48, 49, 50 and 73 are the bit numbers of the facility indications for
each of the required facilities.
Note that we assume that user-space gets compiled with the same
compiler options, therefore we also test for a dfp facility even
if the kernel doesn't make use of it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Mainly merge all different per-cpu arrays into a single array which
holds all topology information per logical cpu.
Also fix the broken core vs socket variable naming and simplify the
locking a bit.
When running in environments without topology information also
invent book, socket and core ids, so that not all ids are zero.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Keep related functions together and move to appropriate file.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move and rename init_storage_keys() to pageattr.c, so it can also be
used from the sclp memory hotplug code in order to initialize
storage keys.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Just convert fault_init() to an early initcall. That's still early
enough since it only needs be called before user space processes get
executed. No reason to externalize it.
Also add the function to the init section and move the store_indication
variable to the read_mostly section.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let the dasd driver and qdio use ccw_device_get_schid and
get rid of other similar functions.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This will be needed by the new virtio-ccw transport.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the BUG_ON's that check for failure or incomplete
results of the s390 hardware crypto instructions.
Rather report the errors as -EIO to the crypto layer.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Preinitialize the program check table, so we can put it into the
read-only data section.
Also use only four byte entries for the table, since each program
check handler resides within the first 2GB. Therefore this reduces
the size of the table by 50% on 64 bit builds.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use 1MB frames for vmemmap if EDAT1 is available in order to
reduce TLB pressure
Always use a 1MB frame even if its only partially needed for
struct pages. Otherwise we would end up with a mix of large
frame and page mappings, because vmemmap_populate gets called
for each section (256MB -> 3.5MB memmap) separately.
Worst case is that we would waste 512KB.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use 2GB frames for indentity mapping if EDAT2 is
available to reduce TLB pressure.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
System time accounting APIs such as vtime_account_system() and
vtime_account_idle() need to be irqsafe. Current callers include
irq entry, exit and kvm, all of which have been checked against that
requirement. Now it's better to grow that with an automatic check
in case we have further callers or we missed something.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
On ia64 and powerpc, vtime context switch only consists
in flushing system and user pending time, plus a few
arch housekeeping.
Consolidate that into a generic implementation. s390 is
a special case because pending user and system time accounting
there is hard to dissociate. So it's keeping its own implementation.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
All vtime implementations just flush the user time on process
tick. Consolidate that in generic code by calling a user time
accounting helper. This avoids an indirect call in ia64 and
prepare to also consolidate vtime context switch code.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Prepending irq-unsafe vtime APIs with underscores was actually
a bad idea as the result is a big mess in the API namespace that
is even waiting to be further extended. Also these helpers
are always called from irq safe callers except kvm. Just
provide a vtime_account_system_irqsafe() for this specific
case so that we can remove the underscore prefix on other
vtime functions.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
irq work can run on any arch even without IPI
support because of the hook on update_process_times().
So lets remove HAVE_IRQ_WORK because it doesn't reflect
any backend requirement.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
In order to promote interoperability between userspace tracers and ftrace,
add a trace_clock that reports raw TSC values which will then be recorded
in the ring buffer. Userspace tracers that also record TSCs are then on
exactly the same time base as the kernel and events can be unambiguously
interlaced.
Tested: Enabled a tracepoint and the "tsc" trace_clock and saw very large
timestamp values.
v2:
Move arch-specific bits out of generic code.
v3:
Rename "x86-tsc", cleanups
v7:
Generic arch bits in Kbuild.
Google-Bug-Id: 6980623
Link: http://lkml.kernel.org/r/1352837903-32191-1-git-send-email-dhsharp@google.com
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@linux.intel.com>
Signed-off-by: David Sharp <dhsharp@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Select HAVE_ALIGNED_STRUCT_PAGE on s390, so that the slub allocator can make
use of compare and swap double for lockless updates. This increases the size
of struct page to 64 bytes (instead of 56 bytes), however the performance gain
justifies the increased size:
- now excactly four struct pages fit into a single cache line; the
case that accessing a struct page causes two cache line loads
does not exist anymore.
- calculating the offset of a struct page within the memmap array
is only a simple shift instead of a more expensive multiplication.
A "hackbench 200 process 200" run on a 32 cpu system did show an 8% runtime
improvement.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
access_ok() returns always "true" on s390. Therefore all access_ok()
invocations are rather pointless.
However when walking page tables we need to make sure that everything
is within bounds of the ASCE limit of the task's address space.
So remove the access_ok() call and add the same check we have in
get_user_pages_fast().
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When walking page tables we need to make sure that everything
is within bounds of the ASCE limit of the task's address space.
Otherwise we might calculate e.g. a pud pointer which is not
within a pud and dereference it.
So check against TASK_SIZE (which is the ASCE limit) before
walking page tables.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current topology code confuses core id vs physical package id.
In other words /sys/devices/system/cpu/cpuX/topology/core_id
displays the physical_package_id (aka socket id) instead of the
core id.
The physical_package_id sysfs attribute always displays "-1"
instead of the socket id.
Fix this mix-up with a small patch which defines and initializes
topology_physical_package_id correctly and fixes the broken
core id handling.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If user space is running in primary mode it can switch to secondary
or access register mode, this is used e.g. in the clock_gettime code
of the vdso. If a signal is delivered to the user space process while
it has been running in access register mode the signal handler is
executed in access register mode as well which will result in a crash
most of the time.
Set the address space control bits in the PSW to the default for the
execution of the signal handler and make sure that the previous
address space control is restored on signal return. Take care
that user space can not switch to the kernel address space by
modifying the registers in the signal frame.
Cc: stable@vger.kernel.org
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
The early mini sclp driver may be called in zArch mode either in
31 or 64 bit addressing mode.
If called in 31 bit addressing mode the new external interrupt psw
however would switch to 64 bit addressing mode. This would cause an
addressing exception within the interrupt handler, since the code
didn't expect the zArch/31 bit addressing mode combination.
Fix this by setting the new psw addressing mode bits so they fit
the current addressing mode.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There's no need to keep __MAX_SUBCHANNEL and __MAX_SSID private to the
common I/O layer when __MAX_CSSID is usable by everybody.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The SO_ATTACH_FILTER option is set only. I propose to add the get
ability by using SO_ATTACH_FILTER in getsockopt. To be less
irritating to eyes the SO_GET_FILTER alias to it is declared. This
ability is required by checkpoint-restore project to be able to
save full state of a socket.
There are two issues with getting filter back.
First, kernel modifies the sock_filter->code on filter load, thus in
order to return the filter element back to user we have to decode it
into user-visible constants. Fortunately the modification in question
is interconvertible.
Second, the BPF_S_ALU_DIV_K code modifies the command argument k to
speed up the run-time division by doing kernel_k = reciprocal(user_k).
Bad news is that different user_k may result in same kernel_k, so we
can't get the original user_k back. Good news is that we don't have
to do it. What we need to is calculate a user2_k so, that
reciprocal(user2_k) == reciprocal(user_k) == kernel_k
i.e. if it's re-loaded back the compiled again value will be exactly
the same as it was. That said, the user2_k can be calculated like this
user2_k = reciprocal(kernel_k)
with an exception, that if kernel_k == 0, then user2_k == 1.
The optlen argument is treated like this -- when zero, kernel returns
the amount of sock_fprog elements in filter, otherwise it should be
large enough for the sock_fprog array.
changes since v1:
* Declared SO_GET_FILTER in all arch headers
* Added decode of vlan-tag codes
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge reason: development work has dependency on kvm patches merged
upstream.
Conflicts:
arch/powerpc/include/asm/Kbuild
arch/powerpc/include/asm/kvm_para.h
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Switching to or from guest context is done on ioctl context.
So by the time we call kvm_guest_enter() or kvm_guest_exit()
we know we are not running the idle task.
As a result, we can directly account the cputime using
vtime_account_system().
There are two good reasons to do this:
* We avoid some useless checks on guest switch. It optimizes
a bit this fast path.
* In the case of CONFIG_IRQ_TIME_ACCOUNTING, calling vtime_account()
checks for irq time to account. This is pointless since we know
we are not in an irq on guest switch. This is wasting cpu cycles
for no good reason. vtime_account_system() OTOH is a no-op in
this config option.
* We can remove the irq disable/enable around kvm guest switch in s390.
A further optimization may consist in introducing a vtime_account_guest()
that directly calls account_guest_time().
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Xiantao Zhang <xiantao.zhang@intel.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
vtime_account_system() currently has only one caller with
vtime_account() which is irq safe.
Now we are going to call it from other places like kvm where
irqs are not always disabled by the time we account the cputime.
So let's make it irqsafe. The arch implementation part is now
prefixed with "__".
vtime_account_idle() arch implementation is prefixed accordingly
to stay consistent.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Similar to pte_none() and pte_present(), the pmd functions should also
respect page protection of huge pages, especially PROT_NONE.
This patch also simplifies massage_pgprot_pmd() by adding new definitions
for huge page protection.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Without CONFIG_HUGETLB_PAGE, pmd_huge() will always return 0. So
pmd_large() should be used instead in places where both transparent
huge pages and hugetlbfs pages can occur.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It turns out that S390 shouldn't use uapi/asm-generic/kvm_para.h since it
defines the functions in its non-UAPI kvm_para.h file.
#including <asm-generic/kvm_para.h> will first pick up
include/asm-generic/kvm_para.h, which defines conflicting functions.
Instead, partially revert commit 0420c87e64,
ungenericising this file and just inserting a comment to prevent the patch
program from deleting it.
cc: Yuanhan Liu <yuanhan.liu@intel.com>
cc: fengguang.wu@intel.com
Reported-by: Yuanhan Liu <yuanhan.liu@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The sysfs and procfs output of the instruction and data caches were
wrong: the output of the data cache provided that instruction cache
values and vice versa.
Fix this by using the correct type indication when issueing the
ecag instruction.
Reported-by: Andreas Krebbel <Andreas.Krebbel@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Because of a change in the s390 arch backend of binutils (commit 23ecd77
"Pick the default arch depending on the target size" in binutils repo)
31 bit builds will fail since the linker would now try to create 64 bit
binary output.
Fix this by setting OUTPUT_ARCH to s390:31-bit instead of s390.
Thanks to Andreas Krebbel for figuring out the issue.
Fixes this build error:
LD init/built-in.o
s390x-4.7.2-ld: s390:31-bit architecture of input file
`arch/s390/kernel/head.o' is incompatible with s390:64-bit output
Cc: Andreas Krebbel <Andreas.Krebbel@de.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The 0x10000 entry point can be called in z/Arch architecture and 64 bit
addressing mode. Therefore this patch removes the unnecessary 31 bit
switch code from the kdump startup function.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Increase the maximum number of available counters and check if
the hardware supports the counter. Support is indicated by the
version of the CPU-measurement counter facility.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add back a hunk from "4dcc2a4 s390/chsc: make headers usable"
which was lost during the merge of the UAPI patch.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make uapi/asm-generic/kvm_para.h non-empty by addition of a comment to stop
the patch program from deleting it when it creates it.
Then delete empty arch-specific uapi/asm/kvm_para.h files and tell the Kbuild
files to use the generic instead.
Should this perhaps instead be a #warning or #error that the facility is
unsupported on this arch?
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Arnd Bergmann <arnd@arndb.de>
cc: Avi Kivity <avi@redhat.com>
cc: Marcelo Tosatti <mtosatti@redhat.com>
cc: kvm@vger.kernel.org
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
Pull timer core update from Thomas Gleixner:
- Bug fixes (one for a longstanding dead loop issue)
- Rework of time related vsyscalls
- Alarm timer updates
- Jiffies updates to remove compile time dependencies
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Cast raw_interval to u64 to avoid shift overflow
timers: Fix endless looping between cascade() and internal_add_timer()
time/jiffies: bring back unconditional LATCH definition
time: Convert x86_64 to using new update_vsyscall
time: Only do nanosecond rounding on GENERIC_TIME_VSYSCALL_OLD systems
time: Introduce new GENERIC_TIME_VSYSCALL
time: Convert CONFIG_GENERIC_TIME_VSYSCALL to CONFIG_GENERIC_TIME_VSYSCALL_OLD
time: Move update_vsyscall definitions to timekeeper_internal.h
time: Move timekeeper structure to timekeeper_internal.h for vsyscall changes
jiffies: Remove compile time assumptions about CLOCK_TICK_RATE
jiffies: Kill unused TICK_USEC_TO_NSEC
alarmtimer: Rename alarmtimer_remove to alarmtimer_dequeue
alarmtimer: Remove unused helpers & defines
alarmtimer: Use hrtimer per-alarm instead of per-base
alarmtimer: Implement minimum alarm interval for allowing suspend
Pull pile 2 of execve and kernel_thread unification work from Al Viro:
"Stuff in there: kernel_thread/kernel_execve/sys_execve conversions for
several more architectures plus assorted signal fixes and cleanups.
There'll be more (in particular, real fixes for the alpha
do_notify_resume() irq mess)..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (43 commits)
alpha: don't open-code trace_report_syscall_{enter,exit}
Uninclude linux/freezer.h
m32r: trim masks
avr32: trim masks
tile: don't bother with SIGTRAP in setup_frame
microblaze: don't bother with SIGTRAP in setup_rt_frame()
mn10300: don't bother with SIGTRAP in setup_frame()
frv: no need to raise SIGTRAP in setup_frame()
x86: get rid of duplicate code in case of CONFIG_VM86
unicore32: remove pointless test
h8300: trim _TIF_WORK_MASK
parisc: decide whether to go to slow path (tracesys) based on thread flags
parisc: don't bother looping in do_signal()
parisc: fix double restarts
bury the rest of TIF_IRET
sanitize tsk_is_polling()
bury _TIF_RESTORE_SIGMASK
unicore32: unobfuscate _TIF_WORK_MASK
mips: NOTIFY_RESUME is not needed in TIF masks
mips: merge the identical "return from syscall" per-ABI code
...
Conflicts:
arch/arm/include/asm/thread_info.h
Newer kernels (linux-next with the transparent huge page patches)
use rrbm if the feature is announced via feature bit 66.
RRBM will cause intercepts, so KVM does not handle it right now,
causing an illegal instruction in the guest.
The easy solution is to disable the feature bit for the guest.
This fixes bugs like:
Kernel BUG at 0000000000124c2a [verbose debug info unavailable]
illegal operation: 0001 [#1] SMP
Modules linked in: virtio_balloon virtio_net ipv6 autofs4
CPU: 0 Not tainted 3.5.4 #1
Process fmempig (pid: 659, task: 000000007b712fd0, ksp: 000000007bed3670)
Krnl PSW : 0704d00180000000 0000000000124c2a (pmdp_clear_flush_young+0x5e/0x80)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:1 PM:0 EA:3
00000000003cc000 0000000000000004 0000000000000000 0000000079800000
0000000000040000 0000000000000000 000000007bed3918 000000007cf40000
0000000000000001 000003fff7f00000 000003d281a94000 000000007bed383c
000000007bed3918 00000000005ecbf8 00000000002314a6 000000007bed36e0
Krnl Code:>0000000000124c2a: b9810025 ogr %r2,%r5
0000000000124c2e: 41343000 la %r3,0(%r4,%r3)
0000000000124c32: a716fffa brct %r1,124c26
0000000000124c36: b9010022 lngr %r2,%r2
0000000000124c3a: e3d0f0800004 lg %r13,128(%r15)
0000000000124c40: eb22003f000c srlg %r2,%r2,63
[ 2150.713198] Call Trace:
[ 2150.713223] ([<00000000002312c4>] page_referenced_one+0x6c/0x27c)
[ 2150.713749] [<0000000000233812>] page_referenced+0x32a/0x410
[...]
CC: stable@vger.kernel.org
CC: Alex Graf <agraf@suse.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
EXTERNAL_CALL and EMERGENCY type interrupts need to preserve their interrupt
code parameter when being injected from user space.
Signed-off-by: Jason J. Herne <jjherne@us.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Pull second s390 update from Martin Schwidefsky:
"The big thing in this pull request is the UAPI patch from David, and
worth mentioning is the page table dumper. The rest are small
improvements and bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/entry: fix svc number for TIF_SYSCALL system call restart
s390/mm,vmem: fix vmem_add_mem()/vmem_remove_range()
s390/vmalloc: have separate modules area
s390/zcrypt: remove duplicated include from zcrypt_pcixcc.c
s390/css_chars: remove superfluous ifdef
s390/chsc: make headers usable
s390/mm: let kernel text section always begin at 1MB
s390/mm: fix mapping of read-only kernel text section
s390/mm: add page table dumper
s390: add support to start the kernel in 64 bit mode.
s390/mm,pageattr: remove superfluous EXPORT_SYMBOLs
s390/mm,pageattr: add more page table walk sanity checks
s390/mm: fix pmd_huge() usage for kernel mapping
s390/dcssblk: cleanup device attribute usage
s390/mm: use pfmf instruction to initialize storage keys
s390/facilities: cleanup PFMF and HPAGE machine facility detection
UAPI: (Scripted) Disintegrate arch/s390/include/asm
Pull generic execve() changes from Al Viro:
"This introduces the generic kernel_thread() and kernel_execve()
functions, and switches x86, arm, alpha, um and s390 over to them."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (26 commits)
s390: convert to generic kernel_execve()
s390: switch to generic kernel_thread()
s390: fold kernel_thread_helper() into ret_from_fork()
s390: fold execve_tail() into start_thread(), convert to generic sys_execve()
um: switch to generic kernel_thread()
x86, um/x86: switch to generic sys_execve and kernel_execve
x86: split ret_from_fork
alpha: introduce ret_from_kernel_execve(), switch to generic kernel_execve()
alpha: switch to generic kernel_thread()
alpha: switch to generic sys_execve()
arm: get rid of execve wrapper, switch to generic execve() implementation
arm: optimized current_pt_regs()
arm: introduce ret_from_kernel_execve(), switch to generic kernel_execve()
arm: split ret_from_fork, simplify kernel_thread() [based on patch by rmk]
generic sys_execve()
generic kernel_execve()
new helper: current_pt_regs()
preparation for generic kernel_thread()
um: kill thread->forking
um: let signal_delivered() do SIGTRAP on singlestepping into handler
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=sTs2
-----END PGP SIGNATURE-----
Merge tag 'disintegrate-s390-20121009' of
git://git.infradead.org/users/dhowells/linux-headers
Pull UAPI patchset from David Howells:
"Can you merge the following branch into the s390 tree please.
This is to complete part of the UAPI disintegration for which the
preparatory patches were pulled recently."
Conflicts:
arch/s390/include/asm/chpid.h
The load of the svc number in the TIF_SYSCALL restart path needs to be
done with an instruction that loads all 64 bits of %r1, 'lh' only loads
32 bits. If the upper half of %r1 is not zero and has the msb set,
entry64.S will try to execute an svc with a really large number.
What will be in the upper half of %r1 depends on the code generated by
gcc for the functions on the do_signal() callchain.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
vmem_add_mem() should only then insert a large page if pmd_none() is true
for the specific entry. We might have a leftover from a previous mapping.
In addition make vmem_remove_range()'s page table walk code more complete
and fix a couple of potential endless loops (which can never happen :).
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a special module area on top of the vmalloc area, which may be only
used for modules and bpf jit generated code.
This makes sure that inter module branches will always happen without a
trampoline and in addition having all the code within a 2GB frame is
branch prediction unit friendly.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
No need for an ifdef __KERNEL__ since css_chars.h is not exported.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make sure that exported headers are save to be included by userspace
exploiting /dev/chsc.
Reported-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let the kernel text section always begin at 1MB. This allows to always have
a large frame in the identity mapping of the kernel image for beginning of
the text section, if the machine has EDAT1 support.
Moving the beginning from 64K to 1MB doesn't cost any memory, since we make
the memory between 64K and 1MB available for the page allocator.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Within the identity mapping the kernel text section is mapped read-only.
However when mapping the first and last page of the text section we must
round upwards and downwards respectively, if only parts of a page belong
to the section.
Otherwise potential rw data can be mapped read-only. So the rounding must
be done just the other way we have it right now.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is more or less the same as the x86 page table dumper which was
merged four years ago: 926e5392 "x86: add code to dump the (kernel)
page tables for visual inspection by kernel developers".
We add a file at /sys/kernel/debug/kernel_page_tables for debugging
purposes so it's quite easy to see the kernel page table layout and
possible odd mappings:
---[ Identity Mapping ]---
0x0000000000000000-0x0000000000100000 1M PTE RW
---[ Kernel Image Start ]---
0x0000000000100000-0x0000000000800000 7M PMD RO
0x0000000000800000-0x00000000008a9000 676K PTE RO
0x00000000008a9000-0x0000000000900000 348K PTE RW
0x0000000000900000-0x0000000001500000 12M PMD RW
---[ Kernel Image End ]---
0x0000000001500000-0x0000000280000000 10219M PMD RW
0x0000000280000000-0x000003d280000000 3904G PUD I
---[ vmemmap Area ]---
0x000003d280000000-0x000003d288c00000 140M PTE RW
0x000003d288c00000-0x000003d300000000 1908M PMD I
0x000003d300000000-0x000003e000000000 52G PUD I
---[ vmalloc Area ]---
0x000003e000000000-0x000003e000009000 36K PTE RW
0x000003e000009000-0x000003e0000ee000 916K PTE I
0x000003e0000ee000-0x000003e000146000 352K PTE RW
0x000003e000146000-0x000003e000200000 744K PTE I
0x000003e000200000-0x000003e080000000 2046M PMD I
0x000003e080000000-0x0000040000000000 126G PUD I
This usually makes only sense for kernel developers. The output
with CONFIG_DEBUG_PAGEALLOC is not very helpful, because of the
huge number of mapped out pages, however I decided for the time
being to not add a !DEBUG_PAGEALLOC dependency.
Maybe it's helpful for somebody even with that option.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do the switch to z/Architecture (alias 64 bit) mode early in head.S.
If the machine is already running in 64 bit mode the sigp turns into
a nop. With this change it doesn't matter in which mode the kernel
is started.
Reviewd-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove some EXPORT_SYMBOLs. There is no module code anywhere
which calls these pageattr functions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current page table walk code in pageattr.c only checks for large pages
while walking the kernel page table, but happily assumes that everything
else is just fine.
Add more checks so we never access invalid memory regions.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
pmd_huge() will always return 0 on !HUGETLBFS, however we use that helper
function when walking the kernel page tables to decide if we have a
1MB page frame or not.
Since we create 1MB frames for the kernel 1:1 mapping independently of
HUGETLBFS this can lead to incorrect storage accesses since the code
can assume that we have a pointer to a page table instead of a pointer
to a 1MB frame.
Fix this by adding a pmd_large() primitive like other architectures have
it already and remove all references to HUGETLBFS/HUGETLBPAGE from the
code that walks kernel page tables.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make use of the pfmf instruction, if available, to initialize storage keys
of whole 1MB or 2GB frames instead of initializing every single page with
the sske instruction.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
MACHINE_HAS_PFMF and MACHINE_HAS_HPAGE actually have the same semantics:
the cpu has the EDAT1 facility installed in zArch mode. So remove one
of the feature flags in machine_flags and rename the other one to EDAT1.
The two old macros simply get mapped to MACHINE_HAS_EDAT1.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Merge patches from Andrew Morton:
"A few misc things and very nearly all of the MM tree. A tremendous
amount of stuff (again), including a significant rbtree library
rework."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (160 commits)
sparc64: Support transparent huge pages.
mm: thp: Use more portable PMD clearing sequenece in zap_huge_pmd().
mm: Add and use update_mmu_cache_pmd() in transparent huge page code.
sparc64: Document PGD and PMD layout.
sparc64: Eliminate PTE table memory wastage.
sparc64: Halve the size of PTE tables
sparc64: Only support 4MB huge pages and 8KB base pages.
memory-hotplug: suppress "Trying to free nonexistent resource <XXXXXXXXXXXXXXXX-YYYYYYYYYYYYYYYY>" warning
mm: memcg: clean up mm_match_cgroup() signature
mm: document PageHuge somewhat
mm: use %pK for /proc/vmallocinfo
mm, thp: fix mlock statistics
mm, thp: fix mapped pages avoiding unevictable list on mlock
memory-hotplug: update memory block's state and notify userspace
memory-hotplug: preparation to notify memory block's state at memory hot remove
mm: avoid section mismatch warning for memblock_type_name
make GFP_NOTRACK definition unconditional
cma: decrease cc.nr_migratepages after reclaiming pagelist
CMA: migrate mlocked pages
kpageflags: fix wrong KPF_THP on non-huge compound pages
...
The transparent huge page code passes a PMD pointer in as the third
argument of update_mmu_cache(), which expects a PTE pointer.
This never got noticed because X86 implements update_mmu_cache() as a
macro and thus we don't get any type checking, and X86 is the only
architecture which supports transparent huge pages currently.
Before other architectures can support transparent huge pages properly we
need to add a new interface which will take a PMD pointer as the third
argument rather than a PTE pointer.
[akpm@linux-foundation.org: implement update_mm_cache_pmd() for s390]
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
.fault now can retry. The retry can break state machine of .fault. In
filemap_fault, if page is miss, ra->mmap_miss is increased. In the second
try, since the page is in page cache now, ra->mmap_miss is decreased. And
these are done in one fault, so we can't detect random mmap file access.
Add a new flag to indicate .fault is tried once. In the second try, skip
ra->mmap_miss decreasing. The filemap_fault state machine is ok with it.
I only tested x86, didn't test other archs, but looks the change for other
archs is obvious, but who knows :)
Signed-off-by: Shaohua Li <shaohua.li@fusionio.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is part of the architecture backend for thp on s390. It
disables thp for kvm hosts, because there is no kvm host hugepage support
so far. Existing thp mappings are split by follow_page() with FOLL_SPLIT,
and future thp mappings are prevented by setting VM_NOHUGEPAGE in
mm->def_flags.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is part of the architecture backend for thp on s390. It
provides the pagetable pre-allocation functions
pgtable_trans_huge_deposit() and pgtable_trans_huge_withdraw(). Unlike
other archs, s390 has no struct page * as pgtable_t, but rather a pointer
to the page table. So instead of saving the pagetable pre- allocation
list info inside the struct page, it is being saved within the pagetable
itself.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is part of the architecture backend for thp on s390. It
provides the functions related to thp splitting, including serialization
against gup. Unlike other archs, pmdp_splitting_flush() cannot use a tlb
flushing operation to serialize against gup on s390, because that wouldn't
be stopped by the disabled IRQs. So instead, smp_call_function() is
called with an empty function, which will have the expected effect.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The core page allocator ensures that page flags are zeroed when freeing
pages via free_pages_check. A number of architectures (ARM, PPC, MIPS)
rely on this property to treat new pages as dirty with respect to the data
cache and perform the appropriate flushing before mapping the pages into
userspace.
This can lead to cache synchronisation problems when using hugepages,
since the allocator keeps its own pool of pages above the usual page
allocator and does not reset the page flags when freeing a page into the
pool.
This patch adds a new architecture hook, arch_clear_hugepage_flags, so
that architectures which rely on the page flags being in a particular
state for fresh allocations can adjust the flags accordingly when a page
is freed into the pool.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Michal Hocko <mhocko@suse.cz>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce SYSCTL_EXCEPTION_TRACE config option and selec it in the
architectures requiring support for the "exception-trace" debug_table
entry in kernel/sysctl.c.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce HAVE_DEBUG_KMEMLEAK config option and select it in corresponding
architecture Kconfig files. DEBUG_KMEMLEAK now only depends on
HAVE_DEBUG_KMEMLEAK.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce HAVE_UID16 config option and select it in corresponding
architecture Kconfig files. UID16 now only depends on HAVE_UID16.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
other branch as normal asm-generic changes do. One is a fix for a
build warning, the other two are more interesting:
* A patch from Mark Brown to allow using the common clock infrastructure
on all architectures, so we can use the clock API in architecture
independent device drivers.
* The UAPI split patches from David Howells for the asm-generic files.
There are other architecture specific series that are going through
the arch maintainer tree and that depend on this one.
There may be a few small merge conflicts between Mark's patch and
the following arch header file split patches. In each case the solution
will be to keep the new "generic-y += clkdev.h" line, even if it
ends up being the only line in the Kbuild file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Aaki
-----END PGP SIGNATURE-----
Merge tag 'asm-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"This has three changes for asm-generic that did not really fit into
any other branch as normal asm-generic changes do. One is a fix for a
build warning, the other two are more interesting:
* A patch from Mark Brown to allow using the common clock
infrastructure on all architectures, so we can use the clock API in
architecture independent device drivers.
* The UAPI split patches from David Howells for the asm-generic
files. There are other architecture specific series that are going
through the arch maintainer tree and that depend on this one.
There may be a few small merge conflicts between Mark's patch and the
following arch header file split patches. In each case the solution
will be to keep the new "generic-y += clkdev.h" line, even if it ends
up being the only line in the Kbuild file."
* tag 'asm-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
UAPI: (Scripted) Disintegrate include/asm-generic
asm-generic: Add default clkdev.h
asm-generic: xor: mark static functions as __maybe_unused
Pull virtio changes from Rusty Russell:
"New workflow: same git trees pulled by linux-next get sent straight to
Linus. Git is awkward at shuffling patches compared with quilt or mq,
but that doesn't happen often once things get into my -next branch."
* 'virtio-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (24 commits)
lguest: fix occasional crash in example launcher.
virtio-blk: Disable callback in virtblk_done()
virtio_mmio: Don't attempt to create empty virtqueues
virtio_mmio: fix off by one error allocating queue
drivers/virtio/virtio_pci.c: fix error return code
virtio: don't crash when device is buggy
virtio: remove CONFIG_VIRTIO_RING
virtio: add help to CONFIG_VIRTIO option.
virtio: support reserved vqs
virtio: introduce an API to set affinity for a virtqueue
virtio-ring: move queue_index to vring_virtqueue
virtio_balloon: not EXPERIMENTAL any more.
virtio-balloon: dependency fix
virtio-blk: fix NULL checking in virtblk_alloc_req()
virtio-blk: Add REQ_FLUSH and REQ_FUA support to bio path
virtio-blk: Add bio-based IO path for virtio-blk
virtio: console: fix error handling in init() function
tools: Fix pthread flag for Makefile of trace-agent used by virtio-trace
tools: Add guest trace agent as a user tool
virtio/console: Allocate scatterlist according to the current pipe size
...
This is a preparatory patch for the introduction of NT_SIGINFO elf note.
Make the location of compat_siginfo_t uniform across eight architectures
which have it. Now it can be pulled in by including asm/compat.h or
linux/compat.h.
Most of the copies are verbatim. compat_uid[32]_t had to be replaced by
__compat_uid[32]_t. compat_uptr_t had to be moved up before
compat_siginfo_t in asm/compat.h on a several architectures (tile already
had it moved up). compat_sigval_t had to be relocated from linux/compat.h
to asm/compat.h.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: "Jonathan M. Foote" <jmfoote@cert.org>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patches from David Howells <dhowells@redhat.com>:
This is to complete part of the UAPI disintegration for which the
preparatory patches were pulled recently.
Note that there are some fixup patches which are at the base of the
branch aimed at you, plus all arches get the asm-generic branch merged in too.
* 'disintegrate-asm-generic' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/asm-generic
UAPI: Fix conditional header installation handling (notably kvm_para.h on m68k)
c6x: remove c6x signal.h
UAPI: Split compound conditionals containing __KERNEL__ in Arm64
UAPI: Fix the guards on various asm/unistd.h files
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=kN6V
-----END PGP SIGNATURE-----
Merge tag 'kvm-3.7-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Avi Kivity:
"Highlights of the changes for this release include support for vfio
level triggered interrupts, improved big real mode support on older
Intels, a streamlines guest page table walker, guest APIC speedups,
PIO optimizations, better overcommit handling, and read-only memory."
* tag 'kvm-3.7-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (138 commits)
KVM: s390: Fix vcpu_load handling in interrupt code
KVM: x86: Fix guest debug across vcpu INIT reset
KVM: Add resampling irqfds for level triggered interrupts
KVM: optimize apic interrupt delivery
KVM: MMU: Eliminate pointless temporary 'ac'
KVM: MMU: Avoid access/dirty update loop if all is well
KVM: MMU: Eliminate eperm temporary
KVM: MMU: Optimize is_last_gpte()
KVM: MMU: Simplify walk_addr_generic() loop
KVM: MMU: Optimize pte permission checks
KVM: MMU: Update accessed and dirty bits after guest pagetable walk
KVM: MMU: Move gpte_access() out of paging_tmpl.h
KVM: MMU: Optimize gpte_access() slightly
KVM: MMU: Push clean gpte write protection out of gpte_access()
KVM: clarify kvmclock documentation
KVM: make processes waiting on vcpu mutex killable
KVM: SVM: Make use of asm.h
KVM: VMX: Make use of asm.h
KVM: VMX: Make lto-friendly
KVM: x86: lapic: Clean up find_highest_vector() and count_vectors()
...
Conflicts:
arch/s390/include/asm/processor.h
arch/x86/kvm/i8259.c
Pull crypto update from Herbert Xu:
- Optimised AES/SHA1 for ARM.
- IPsec ESN support in talitos and caam.
- x86_64/avx implementation of cast5/cast6.
- Add/use multi-algorithm registration helpers where possible.
- Added IBM Power7+ in-Nest support.
- Misc fixes.
Fix up trivial conflicts in crypto/Kconfig due to the sparc64 crypto
config options being added next to the new ARM ones.
[ Side note: cut-and-paste duplicate help texts make those conflicts
harder to read than necessary, thanks to git being smart about
minimizing conflicts and maximizing the common parts... ]
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (71 commits)
crypto: x86/glue_helper - fix storing of new IV in CBC encryption
crypto: cast5/avx - fix storing of new IV in CBC encryption
crypto: tcrypt - add missing tests for camellia and ghash
crypto: testmgr - make test_aead also test 'dst != src' code paths
crypto: testmgr - make test_skcipher also test 'dst != src' code paths
crypto: testmgr - add test vectors for CTR mode IV increasement
crypto: testmgr - add test vectors for partial ctr(cast5) and ctr(cast6)
crypto: testmgr - allow non-multi page and multi page skcipher tests from same test template
crypto: caam - increase TRNG clocks per sample
crypto, tcrypt: remove local_bh_disable/enable() around local_irq_disable/enable()
crypto: tegra-aes - fix error return code
crypto: crypto4xx - fix error return code
crypto: hifn_795x - fix error return code
crypto: ux500 - fix error return code
crypto: caam - fix error IDs for SEC v5.x RNG4
hwrng: mxc-rnga - Access data via structure
hwrng: mxc-rnga - Adapt clocks to new i.mx clock framework
crypto: caam - add IPsec ESN support
crypto: 842 - remove .cra_list initialization
Revert "[CRYPTO] cast6: inline bloat--"
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=VtEQ
-----END PGP SIGNATURE-----
Merge tag 'uapi-prep-20121002' of git://git.infradead.org/users/dhowells/linux-headers
Pull preparatory patches for user API disintegration from David Howells:
"The patches herein prepare for the extraction of the Userspace API
bits from the various header files named in the Kbuild files.
New subdirectories are created under either include/uapi/ or
arch/x/include/uapi/ that correspond to the subdirectory containing
that file under include/ or arch/x/include/.
The new subdirs under the uapi/ directory are populated with Kbuild
files that mostly do nothing at this time. Further patches will
disintegrate the headers in each original directory and fill in the
Kbuild files as they do it.
These patches also:
(1) fix up #inclusions of "foo.h" rather than <foo.h>.
(2) Remove some redundant #includes from the DRM code.
(3) Make the kernel build infrastructure handle Kbuild files both in
the old places and the new UAPI place that both specify headers
to be exported.
(4) Fix some kernel tools that #include kernel headers during their
build.
I have compile tested this with allyesconfig against x86_64,
allmodconfig against i386 and a scattering of additional defconfigs of
other arches. Prepared for main script
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>"
* tag 'uapi-prep-20121002' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: Plumb the UAPI Kbuilds into the user header installation and checking
UAPI: x86: Differentiate the generated UAPI and internal headers
UAPI: Remove the objhdr-y export list
UAPI: Move linux/version.h
UAPI: Set up uapi/asm/Kbuild.asm
UAPI: x86: Fix insn_sanity build failure after UAPI split
UAPI: x86: Fix the test_get_len tool
UAPI: (Scripted) Set up UAPI Kbuild files
UAPI: Partition the header include path sets and add uapi/ header directories
UAPI: (Scripted) Convert #include "..." to #include <path/...> in kernel system headers
UAPI: (Scripted) Convert #include "..." to #include <path/...> in drivers/gpu/
UAPI: (Scripted) Remove redundant DRM UAPI header #inclusions from drivers/gpu/.
UAPI: Refer to the DRM UAPI headers with <...> and from certain headers only
Ease the deployment of clkdev by providing a default asm/clkdev.h for
use if the arch does not have an include/asm/clkdev.h.
Due to limitations in Kbuild we manually add clkdev.h to all
architectures that don't have one rather than having the header appear
by default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull vfs update from Al Viro:
- big one - consolidation of descriptor-related logics; almost all of
that is moved to fs/file.c
(BTW, I'm seriously tempted to rename the result to fd.c. As it is,
we have a situation when file_table.c is about handling of struct
file and file.c is about handling of descriptor tables; the reasons
are historical - file_table.c used to be about a static array of
struct file we used to have way back).
A lot of stray ends got cleaned up and converted to saner primitives,
disgusting mess in android/binder.c is still disgusting, but at least
doesn't poke so much in descriptor table guts anymore. A bunch of
relatively minor races got fixed in process, plus an ext4 struct file
leak.
- related thing - fget_light() partially unuglified; see fdget() in
there (and yes, it generates the code as good as we used to have).
- also related - bits of Cyrill's procfs stuff that got entangled into
that work; _not_ all of it, just the initial move to fs/proc/fd.c and
switch of fdinfo to seq_file.
- Alex's fs/coredump.c spiltoff - the same story, had been easier to
take that commit than mess with conflicts. The rest is a separate
pile, this was just a mechanical code movement.
- a few misc patches all over the place. Not all for this cycle,
there'll be more (and quite a few currently sit in akpm's tree)."
Fix up trivial conflicts in the android binder driver, and some fairly
simple conflicts due to two different changes to the sock_alloc_file()
interface ("take descriptor handling from sock_alloc_file() to callers"
vs "net: Providing protocol type via system.sockprotoname xattr of
/proc/PID/fd entries" adding a dentry name to the socket)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (72 commits)
MAX_LFS_FILESIZE should be a loff_t
compat: fs: Generic compat_sys_sendfile implementation
fs: push rcu_barrier() from deactivate_locked_super() to filesystems
btrfs: reada_extent doesn't need kref for refcount
coredump: move core dump functionality into its own file
coredump: prevent double-free on an error path in core dumper
usb/gadget: fix misannotations
fcntl: fix misannotations
ceph: don't abuse d_delete() on failure exits
hypfs: ->d_parent is never NULL or negative
vfs: delete surplus inode NULL check
switch simple cases of fget_light to fdget
new helpers: fdget()/fdput()
switch o2hb_region_dev_write() to fget_light()
proc_map_files_readdir(): don't bother with grabbing files
make get_file() return its argument
vhost_set_vring(): turn pollstart/pollstop into bool
switch prctl_set_mm_exe_file() to fget_light()
switch xfs_find_handle() to fget_light()
switch xfs_swapext() to fget_light()
...
Pull user namespace changes from Eric Biederman:
"This is a mostly modest set of changes to enable basic user namespace
support. This allows the code to code to compile with user namespaces
enabled and removes the assumption there is only the initial user
namespace. Everything is converted except for the most complex of the
filesystems: autofs4, 9p, afs, ceph, cifs, coda, fuse, gfs2, ncpfs,
nfs, ocfs2 and xfs as those patches need a bit more review.
The strategy is to push kuid_t and kgid_t values are far down into
subsystems and filesystems as reasonable. Leaving the make_kuid and
from_kuid operations to happen at the edge of userspace, as the values
come off the disk, and as the values come in from the network.
Letting compile type incompatible compile errors (present when user
namespaces are enabled) guide me to find the issues.
The most tricky areas have been the places where we had an implicit
union of uid and gid values and were storing them in an unsigned int.
Those places were converted into explicit unions. I made certain to
handle those places with simple trivial patches.
Out of that work I discovered we have generic interfaces for storing
quota by projid. I had never heard of the project identifiers before.
Adding full user namespace support for project identifiers accounts
for most of the code size growth in my git tree.
Ultimately there will be work to relax privlige checks from
"capable(FOO)" to "ns_capable(user_ns, FOO)" where it is safe allowing
root in a user names to do those things that today we only forbid to
non-root users because it will confuse suid root applications.
While I was pushing kuid_t and kgid_t changes deep into the audit code
I made a few other cleanups. I capitalized on the fact we process
netlink messages in the context of the message sender. I removed
usage of NETLINK_CRED, and started directly using current->tty.
Some of these patches have also made it into maintainer trees, with no
problems from identical code from different trees showing up in
linux-next.
After reading through all of this code I feel like I might be able to
win a game of kernel trivial pursuit."
Fix up some fairly trivial conflicts in netfilter uid/git logging code.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (107 commits)
userns: Convert the ufs filesystem to use kuid/kgid where appropriate
userns: Convert the udf filesystem to use kuid/kgid where appropriate
userns: Convert ubifs to use kuid/kgid
userns: Convert squashfs to use kuid/kgid where appropriate
userns: Convert reiserfs to use kuid and kgid where appropriate
userns: Convert jfs to use kuid/kgid where appropriate
userns: Convert jffs2 to use kuid and kgid where appropriate
userns: Convert hpfs to use kuid and kgid where appropriate
userns: Convert btrfs to use kuid/kgid where appropriate
userns: Convert bfs to use kuid/kgid where appropriate
userns: Convert affs to use kuid/kgid wherwe appropriate
userns: On alpha modify linux_to_osf_stat to use convert from kuids and kgids
userns: On ia64 deal with current_uid and current_gid being kuid and kgid
userns: On ppc convert current_uid from a kuid before printing.
userns: Convert s390 getting uid and gid system calls to use kuid and kgid
userns: Convert s390 hypfs to use kuid and kgid where appropriate
userns: Convert binder ipc to use kuids
userns: Teach security_path_chown to take kuids and kgids
userns: Add user namespace support to IMA
userns: Convert EVM to deal with kuids and kgids in it's hmac computation
...
Set up empty UAPI Kbuild files to be populated by the header splitter.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Pull s390 updates from Martin Schwidefsky:
"The main new feature is machine support for System zEC12 including
transactional memory, runtime instrumentation, support for scm block
devices via eadm subchannels, and support for CEX4 crypto cards.
In addition there are some nice improvements: bpf jit compiler, arch
backend for cmpxchg_double, relative exception table entries, dasd
partition detection independent from the dasd driver ioctls, and cpu
cache information in /proc/cpuinfo and /sys/device/cpu.
And last but not least a series of cleanup patches from Heiko."
Fix up trivial add-add conflict in arch/s390/Kconfig due to commit
b952741c80 ("cputime: Generalize CONFIG_VIRT_CPU_ACCOUNTING")
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (76 commits)
s390: update defconfig
s390/jump label,nss: let shared kernel support depend on !JUMP_LABEL
s390/disassembler: fix decoding of risblg instruction
s390/bpf,jit: add support for BPF_S_ANC_ALU_XOR_X instruction
s390/traps: move call to print_modules() out of show_regs()
s390/mm: mark free_initrd_mem() as __init
s390/dasd: check count address during online setting
drivers/s390/char/monreader.c: fix error return code
s390/cmpxchg,percpu: implement cmpxchg_double()
s390/percpu: implement this_cpu_add_return()
s390/percpu: implement this_cpu_xchg()
s390/kexec: remove CONFIG_KEXEC
s390/irq: use designated initializers for irq class array
s390: add uninitialized_var() to suppress false positive compiler warnings
s390/crashdump: move fill_cpu_elf_notes() prototype to header file
s390/process: add missing header include
s390/ptrace: add missing ifdef
s390/ipl,decrompressor: disable branch profiling
s390/perf_events: compile only for CONFIG_64BIT
s390/tape: remove even more tape block leftovers
...
Pull scheduler changes from Ingo Molnar:
"Continued quest to clean up and enhance the cputime code by Frederic
Weisbecker, in preparation for future tickless kernel features.
Other than that, smallish changes."
Fix up trivial conflicts due to additions next to each other in arch/{x86/}Kconfig
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
cputime: Make finegrained irqtime accounting generally available
cputime: Gather time/stats accounting config options into a single menu
ia64: Reuse system and user vtime accounting functions on task switch
ia64: Consolidate user vtime accounting
vtime: Consolidate system/idle context detection
cputime: Use a proper subsystem naming for vtime related APIs
sched: cpu_power: enable ARCH_POWER
sched/nohz: Clean up select_nohz_load_balancer()
sched: Fix load avg vs. cpu-hotplug
sched: Remove __ARCH_WANT_INTERRUPTS_ON_CTXSW
sched: Fix nohz_idle_balance()
sched: Remove useless code in yield_to()
sched: Add time unit suffix to sched sysctl knobs
sched/debug: Limit sd->*_idx range on sysctl
sched: Remove AFFINE_WAKEUPS feature flag
s390: Remove leftover account_tick_vtime() header
cputime: Consolidate vtime handling on context switch
sched: Move cputime code to its own file
cputime: Generalize CONFIG_VIRT_CPU_ACCOUNTING
tile: Remove SD_PREFER_LOCAL leftover
...
Make default just return 0. The current default (checking
TIF_POLLING_NRFLAG) is taken to architectures that need it;
ones that don't do polling in their idle threads don't need
to defined TIF_POLLING_NRFLAG at all.
ia64 defined both TS_POLLING (used by its tsk_is_polling())
and TIF_POLLING_NRFLAG (not used at all). Killed the latter...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Everyone who selects VIRTIO is also made to select VIRTIO_RING; just make
them synonymous, since we removed the indirection layer some time ago.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Use the mapping of Elf_[SPE]hdr, Elf_Addr, Elf_Sym, Elf_Dyn, Elf_Rel/Rela,
ELF_R_TYPE() and ELF_R_SYM() to either the 32-bit version or the 64-bit version
into asm-generic/module.h for all arches bar MIPS.
Also, use the generic definition mod_arch_specific where possible.
To this end, I've defined three new config bools:
(*) HAVE_MOD_ARCH_SPECIFIC
Arches define this if they don't want to use the empty generic
mod_arch_specific struct.
(*) MODULES_USE_ELF_RELA
Arches define this if their modules can contain RELA records. This causes
the Elf_Rela mapping to be emitted and allows apply_relocate_add() to be
defined by the arch rather than have the core emit an error message.
(*) MODULES_USE_ELF_REL
Arches define this if their modules can contain REL records. This causes
the Elf_Rel mapping to be emitted and allows apply_relocate() to be
defined by the arch rather than have the core emit an error message.
Note that it is possible to allow both REL and RELA records: m68k and mips are
two arches that do this.
With this, some arch asm/module.h files can be deleted entirely and replaced
with a generic-y marker in the arch Kbuild file.
Additionally, I have removed the bits from m32r and score that handle the
unsupported type of relocation record as that's now handled centrally.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Recent changes (KVM: make processes waiting on vcpu mutex killable)
now requires to check the return value of vcpu_load. This triggered
a warning in s390 specific kvm code. Turns out that we can actually
remove the put/load, since schedule will do the right thing via
the preempt notifiers.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We can have either shared kernel or jump label support, but not both.
If a kernel gets IPL'ed from an NSS it's not possible to patch the
text segment, since it's read-only.
Therefore any static branches cannot be updated. So we need to make
sure that shared kernel support is disabled if jump label support
is enabled.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for new BPF_S_ANC_ALU_XOR_X instruction which got added
with ffe06c17 "filter: add XOR operation".
s390 version of 4bfaddf1 "x86 bpf_jit: support BPF_S_ANC_ALU_XOR_X instruction".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Same as 0fa0e2f0 "x86: Move call to print_modules() out of show_regs()".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Same as 0d26d1d8 "x86/mm: Mark free_initrd_mem() as __init".
In addition also add the __init annotation to setup_zero_pages().
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The generic variant has a local_irq_save/restore pair which is quite
expensive. It is sufficient to disable preemption, which is a no-op
with !CONFIG_PREEMPT and then use the regular xchg macro.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since "Kconfig: split the s390 base menu" CONFIG_KEXEC gets always selected.
Therefore there is no point in keeping CONFIG_KEXEC anywhere.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use designated initializers for the irq class array in irq.c so
it's always guaranteed that the order of elements is equal to
their corresponding parts in irq.h.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Get rid of these:
arch/s390/kernel/smp.c:134:19: warning: ‘status’ may be used uninitialized in this function [-Wuninitialized]
arch/s390/mm/pgtable.c:641:10: warning: ‘table’ may be used uninitialized in this function [-Wuninitialized]
arch/s390/mm/pgtable.c:644:12: warning: ‘page’ may be used uninitialized in this function [-Wuninitialized]
drivers/s390/cio/cio.c:1037:14: warning: ‘schid’ may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move fill_cpu_elf_notes() prototype to header file.
This way we get compile errors if e.g. the number of function
parameters get changed.
Otherwise it's possible to change just the definition and everything
else still compiles fine, but the result is broken code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add appropriate header file:
arch/s390/kernel/process.c:327:15: warning: symbol 'arch_align_stack' was not declared.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
if (MACHINE_HAS_TE) translates to if (0) on !CONFIG_64BIT however the
compiler still warns about invalid shifts within non-reachable code.
So add an explicit ifdef to get rid of this warning:
arch/s390/kernel/ptrace.c: In function ‘update_per_regs’:
arch/s390/kernel/ptrace.c:63:4: warning: left shift count >= width of type [enabled by default]
arch/s390/kernel/ptrace.c:65:4: warning: left shift count >= width of type [enabled by default]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The early kernel decrompressing code can't call into the kernel
in order to profile branches. Fixes this link error:
arch/s390/boot/compressed/misc.o: In function `decompress_kernel':
misc.c:(.text+0x9a6): undefined reference to `ftrace_likely_update'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The whole hardware support is only available in zArch mode.
Fixes also this compile warning:
arch/s390/kernel/perf_cpum_cf.c: In function ‘cpumf_pmu_init’:
arch/s390/kernel/perf_cpum_cf.c:670:2: warning: left shift count >= width of type [enabled by default]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use for_each_set_bit() to simplify the code.
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change return value of appldata_asm() to -EOPNOTSUPP in case of an
error. The return value was only used internally and not passed to
user space.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Returning -ENOSYS on kexec_load() is a bad idea since user space cannot
tell if the system call is not implmented or if it failed.
Use -EOPNOTSUPP in case somebody tries a kexec_load on a NSS image based
kernel instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change -ENOSYS to -EOPNOTSUPP. Return value is used only internally.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change return code handling of the stsi() function:
In case function code 0 was specified the return value is the
current configuration level (already shifted). That way all
the code that actually copied the stsi_0() function can go
away.
Otherwise the return value is 0 (success) or negative to
indicate an error (currently only -EOPNOTSUPP).
Also stsi() is no longer an inline function. The function is
not performance critical, but every caller would generate an
exception table entry for this function.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is the s390 port of 70627654 "x86, extable: Switch to relative
exception table entries".
Reduces the size of our exception tables by 50% on 64 bit builds.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the spinlock from struct scm_device. drvdata and attributes
are guarded via device_lock.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The cpu polarization member is the only per cpu state that is not part
of the pcpu structure. So add it there and have everything in one place.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The maximum nesting of the cpu topology is evaluated when /proc/sysinfo
is the first time read. This happens without a lock and a concurrent
reader on a different cpu can see and use an invalid intermediate value.
Besides the fact that this race is quite unlikely the worst thing that
could happen is that /proc/sysinfo would contain bogus information about
the machine's cpu topology.
Nevertheless this should be fixed. So move the detection code to the
early machine detection code and since now the value is early available
use it in the topology code as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch introduces the __get_user_pages_fast() function on s390,
which will be needed with CONFIG_TRANSPARENT_HUGEPAGE and futex.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a couple of missing fields that were introduced with z196.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current proc implementation of the /proc/sysinfo file writes all
informations contained in all system information blocks to a single
page.
This is done by calling sprintf all the time in the expectation that
everything will fit into a single page. This however is not necessarily
true if the configuration of a machine is very large.
So convert /proc/sysinfo to avoid writing into random memory regions.
For readability reasons a couple of lines are longer than 80 characters.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Any change to sysinfo.h causes a whole kernel recompile since sysinfo.h is
included by topology.h, which again is used nearly everywhere.
So remove that include and add a forward declaration instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Shorten the code for addressing mode initialization. Also add missing
__init annotations, since this code is only used during kernel initialization.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Renaming the globally visible variable "user_mode" to "addressing_mode" in
order to fix a name clash was not a good idea. (Commit 37fe1d73 "s390/mm:
rename user_mode variable to addressing_mode")
Looking at the code after a couple of weeks one thinks: addressing mode of
what?
So rename the variable again. This time to s390_user_mode. Which hopefully
makes more sense.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change the default addressing mode so that user space runs in primary space
and the kernel runs in home space.
In addition remove the "switch_amode" kernel parameter so all users who
already specified they want the new default behaviour will stay in the
"switched" mode instead of in the opposite they intended.
If there is a need to switch addressing modes, this can be done with the
"user_mode" kernel parameter: user_mode=home
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a sigp instruction is issued it may store a status. This status is
currently stored in a per cpu field of the target cpu.
If multiple cpus issue a sigp instruction with the same target cpu
and a status is stored the result is not necessarily as expected.
Currently this is not an issue:
- on cpu hotplug no sigps, except "restart" and "sense" are sent to the
target cpu.
- on external call we don't look at the status if it is stored
- on sense running the condition code "status stored" is sufficient to
tell if a cpu is running or not
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a line for each cpu cache to /proc/cpuinfo.
Since we only have information of private cpu caches in sysfs we
add a line for each cpu cache in /proc/cpuinfo which will also
contain information about shared caches.
For a z196 machine /proc/cpuinfo now looks like:
vendor_id : IBM/S390
bogomips per cpu: 14367.00
features : esan3 zarch stfle msa ldisp eimm dfp etf3eh highgprs
cache0 : level=1 type=Data scope=Private size=64K line_size=256 associativity=4
cache1 : level=1 type=Instruction scope=Private size=128K line_size=256 associativity=8
cache2 : level=2 type=Unified scope=Private size=1536K line_size=256 associativity=12
cache3 : level=3 type=Unified scope=Shared size=24576K line_size=256 associativity=12
cache4 : level=4 type=Unified scope=Shared size=196608K line_size=256 associativity=24
processor 0: version = FF, identification = 000123, machine = 2817
processor 1: version = FF, identification = 100123, machine = 2817
processor 2: version = FF, identification = 200123, machine = 2817
processor 3: version = FF, identification = 200123, machine = 2817
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow user-space processes to use transactional execution (TX).
If the TX facility is available user space programs can use
transactions for fine-grained serialization based on the data
objects that are referenced during a transaction. This is
useful for lockless data structures and speculative compiler
optimizations.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow user-space threads to use runtime instrumentation (RI). To enable RI
for a thread there is a new s390 specific system call, sys_s390_runtime_instr,
that takes as parameter a realtime signal number. If the RI facility is
available the system call sets up a control block for the calling thread with
the appropriate permissions for the thread to modify the control block.
The user-space thread can then use the store and modify RI instructions to
alter the control block and start/stop the instrumentation via RION/RIOFF.
If the user specified program buffer runs full RI triggers an external
interrupt. The external interrupt is translated to a real-time signal that
is delivered to the thread that enabled RI on that CPU. The number of
the real-time signal is the number specified in the RI system call. So,
user-space can select any available real-time signal number in case the
application itself uses real-time signals for other purposes.
The kernel saves the RI control blocks on task switch only if the running
thread was enabled for RI. Therefore, the performance impact on task switch
should be negligible if RI is not used.
RI is only enabled for user-space mode and is disabled for the supervisor
state.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for EADM interrupt statistics in /proc/interrupts.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This driver allows usage of EADM subchannels. EADM subchannels
act as a communication vehicle for SCM increments.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Detect an scm change notification in store event information.
Update affected scm devices and notify their drivers.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Bus driver to manage Storage Class Memory.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add structures to be used by the eadm subchannel driver.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add the eadm facility bits to the css characteristics and move
them to a new header.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
machine_crash_shutdown() was the only function in crash.c.
So move the function and delete one file.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Unify all our cpu hotplug notifiers to mask out the CPU_TASKS_FROZEN
bit, so we don't have to add all the *_FROZEN variant cases to the
notifiers.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For SMP and !SMP smp_find_processor_id() either takes a u16 or
an unsigned int argument. Fix this so both versions take a u16.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CONFIG_S390_GUEST determines whether virtio guest drivers are built, and
the virtio console is not enforced as default.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Split the base menu into more descriptive categories like processor,
memory, etc. and move virtualization related entries to the
Virtualization menu.
Also select KEXEC unconditionally.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Expose cpu cache topology via sysfs.
The created sysfs directory structure is compatible to what x86, ia64
and powerpc have.
On s390 we expose only information about cpu caches which are private
to a cpu via sysfs . Caches which are shared between cpus do not have
a sysfs representation.
The reason for that is that the file "shared_cpu_map" is mandatory
and only if running under LPAR it is possible to tell which cpus
share which cache. Second level hypervisors however do not and cannot
expose that information to guests.
In order to have a consistent view we made the choice to always only
expose information about private cpu caches via sysfs.
Example for a z196 cpu (cpu1 in /sys/devices/cpu):
cpu1/cache/index0/size -- 64K
cpu1/cache/index0/type -- Data
cpu1/cache/index0/level -- 1
cpu1/cache/index0/number_of_sets -- 64
cpu1/cache/index0/shared_cpu_map -- 00000000,00000002
cpu1/cache/index0/shared_cpu_list -- 1
cpu1/cache/index0/coherency_line_size -- 256
cpu1/cache/index0/ways_of_associativity -- 4
cpu1/cache/index1/size -- 128K
cpu1/cache/index1/type -- Instruction
cpu1/cache/index1/level -- 1
cpu1/cache/index1/number_of_sets -- 64
cpu1/cache/index1/shared_cpu_map -- 00000000,00000002
cpu1/cache/index1/shared_cpu_list -- 1
cpu1/cache/index1/coherency_line_size -- 256
cpu1/cache/index1/ways_of_associativity -- 8
cpu1/cache/index2/size -- 1536K
cpu1/cache/index2/type -- Unified
cpu1/cache/index2/level -- 2
cpu1/cache/index2/number_of_sets -- 512
cpu1/cache/index2/shared_cpu_map -- 00000000,00000002
cpu1/cache/index2/shared_cpu_list -- 1
cpu1/cache/index2/coherency_line_size -- 256
cpu1/cache/index2/ways_of_associativity -- 12
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
So far, large page support was completely disabled with
CONFIG_DEBUG_PAGEALLOC, although it would be sufficient if only the
large page kernel mapping was disabled. This patch enables large page
support with CONFIG_DEBUG_PAGEALLOC, while it prevents the large kernel
mapping in that case.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Our memcpy and memcmp variants were implemented by calling the corresponding
gcc builtin variants.
However gcc is free to replace a call to __builtin_memcmp with a call to memcmp
which, when called, will result in an endless recursion within memcmp.
So let's provide asm variants and also fix the variants that are used for
uncompressing the kernel image.
In addition remove all other occurences of builtin function calls.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make use of new immediate instructions that came with the
extended immediate and general instruction extension facilities.
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390 implementation of the JIT compiler for packet filter speedup.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the code that finds out to which context we account the
cputime into generic layer.
Archs that consider the whole time spent in the idle task as idle
time (ia64, powerpc) can rely on the generic vtime_account()
and implement vtime_account_system() and vtime_account_idle(),
letting the generic code to decide when to call which API.
Archs that have their own meaning of idle time, such as s390
that only considers the time spent in CPU low power mode as idle
time, can just override vtime_account().
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Use a naming based on vtime as a prefix for virtual based
cputime accounting APIs:
- account_system_vtime() -> vtime_account()
- account_switch_vtime() -> vtime_task_switch()
It makes it easier to allow for further declension such
as vtime_account_system(), vtime_account_idle(), ... if we
want to find out the context we account to from generic code.
This also make it better to know on which subsystem these APIs
refer to.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
To help migrate archtectures over to the new update_vsyscall method,
redfine CONFIG_GENERIC_TIME_VSYSCALL as CONFIG_GENERIC_TIME_VSYSCALL_OLD
Cc: Tony Luck <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Since users will need to include timekeeper_internal.h, move
update_vsyscall definitions to timekeeper_internal.h.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Pull s390 fixes from Martin Schwidefsky:
"Bug fixes for 3.6-rc7, including some important patches for large page
related memory management issues."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/dasd: fix read unit address configuration loop
s390/dasd: fix pathgroup race
s390/mm: fix user access page-table walk code
s390/hwcaps: do not report high gprs for 31 bit kernel
s390/cio: invalidate cdev pointer before deregistration
s390/cio: fix IO subchannel event race
s390/dasd: move wake_up call
s390/hugetlb: use direct TLB flushing for hugetlbfs pages
s390/mm: fix deadlock in unmap_hugepage_range()
Convert getresuid, getresgid, getuid, geteuid, getgid, getegid
Convert struct cred kuids and kgids into userspace uids and gids when
returning them.
These s390 system calls slipped through the cracks in my first
round of converstions :(
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
The s390 page-table walk code, used for user copy and futex, currently
cannot handle huge pages. As far as user copy is concerned, that is
not really a problem because those functions will only be used on old
hardware that has no huge page support. But the futex code will also
use pagetable walk functions on current hardware when user space runs
in primary space mode. So, if a futex sits in a huge page, the futex
operation on it will result in a page fault loop or even data
corruption.
This patch adds the code for resolving huge page mappings in the user
access pagetable walk code on s390.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull perf fixes from Ingo Molnar:
"This tree includes various fixes"
Ingo really needs to improve on the whole "explain git pull" part.
"Various fixes" indeed.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/hwpb: Invoke __perf_event_disable() if interrupts are already disabled
perf/x86: Enable Intel Cedarview Atom suppport
perf_event: Switch to internal refcount, fix race with close()
oprofile, s390: Fix uninitialized memory access when writing to oprofilefs
perf/x86: Fix microcode revision check for SNB-PEBS
The bit for high gprs in the AT_HWCAP auxiliary vector field and the
highgprs tag in the output of /proc/cpuinfo should not be set for
31 bit kernels.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introducing kvm_arch_flush_shadow_memslot, to invalidate the
translations of a single memory slot.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
huge_ptep_get_and_clear() is either missing a TLB invalidation or
an mm->context.attach_count check. Since the attach_count logic was
introduced with normal ptes in mind, let's just use direct TLB
flushing for hugetlbfs pages.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
git commit cd2934a3 moved the flush_tlb_range() within
__unmap_hugepage_range() inside the mm->page_table_lock, which
triggered a deadlock in s390 tlb flushing code. __tlb_flush_mm_cond()
also tries to acquire the mm->page_table_lock, but that is not needed
because all callers already have mm->mmap_sem or mm->page_table_lock,
so it can be safely removed to fix the deadlock.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In native 32 bit mode the personality flags were not correctly inherited.
This is the s390 version of 59e4c3a2 "powerpc/32: Don't clobber personality
flags on exec".
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix this compile error:
arch/s390/kernel/machine_kexec.c: In function ‘setup_regs’:
arch/s390/kernel/machine_kexec.c:63:3: error: implicit declaration
of function ‘smp_store_status’ [-Werror=implicit-function-declaration]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If oprofilefs_ulong_from_user() is called with count equals zero, *val
remains unchanged. Depending on the implementation it might be
uninitialized. Fixing users of oprofilefs_ulong_ from_user().
We missed these s390 changes with:
913050b oprofile: Fix uninitialized memory access when writing to writing to oprofilefs
Cc: stable@vger.kernel.org # 3.3+
Signed-off-by: Robert Richter <robert.richter@amd.com>
Merging critical fixes from upstream required for development.
* upstream/master: (809 commits)
libata: Add a space to " 2GB ATA Flash Disk" DMA blacklist entry
Revert "powerpc: Update g5_defconfig"
powerpc/perf: Use pmc_overflow() to detect rolled back events
powerpc: Fix VMX in interrupt check in POWER7 copy loops
powerpc: POWER7 copy_to_user/copy_from_user patch applied twice
powerpc: Fix personality handling in ppc64_personality()
powerpc/dma-iommu: Fix IOMMU window check
powerpc: Remove unnecessary ifdefs
powerpc/kgdb: Restore current_thread_info properly
powerpc/kgdb: Bail out of KGDB when we've been triggered
powerpc/kgdb: Do not set kgdb_single_step on ppc
powerpc/mpic_msgr: Add missing includes
powerpc: Fix null pointer deref in perf hardware breakpoints
powerpc: Fixup whitespace in xmon
powerpc: Fix xmon dl command for new printk implementation
xfs: check for possible overflow in xfs_ioc_trim
xfs: unlock the AGI buffer when looping in xfs_dialloc
xfs: fix uninitialised variable in xfs_rtbuf_get()
powerpc/fsl: fix "Failed to mount /dev: No such device" errors
powerpc/fsl: update defconfigs
...
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
On s390x-linux-gcc, __SIZE_TYPE__ expands to "long unsigned int" for both
32-bit s390 and 64-bit s390x, as
gcc-4.6.3-nolibc/s390x-linux/lib/gcc/s390x-linux/4.6.3/plugin/include/config/s390/linux.h
has
#define SIZE_TYPE (TARGET_64BIT ? "long unsigned int" : "long unsigned int")
To match this, __kernel_size_t is always set to "long unsigned int".
But while __kernel_ssize_t is "long" on 64-bit s390x, it is "int" on 32-bit
s390, causing compiler warnings like:
fs/quota/quota_tree.c:372:4: warning: format '%zd' expects argument of type 'signed size_t', but argument 4 has type 'ssize_t' [-Wformat]
To fix this, __kernel_ssize_t should be "long", irrespective of word size.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The archs that implement virtual cputime accounting all
flush the cputime of a task when it gets descheduled
and sometimes set up some ground initialization for the
next task to account its cputime.
These archs all put their own hooks in their context
switch callbacks and handle the off-case themselves.
Consolidate this by creating a new account_switch_vtime()
callback called in generic code right after a context switch
and that these archs must implement to flush the prev task
cputime and initialize the next task cputime related state.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
S390, ia64 and powerpc all define their own version
of CONFIG_VIRT_CPU_ACCOUNTING. Generalize the config
and its description to a single place to avoid
duplication.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
The native 31 bit and the compat behaviour for the mmap system calls differ:
In native 31 bit mode the passed in address for the mmap system call will be
unmodified passed to sys_mmap_pgoff().
In compat mode however the passed in address will be modified with
compat_ptr() which masks out the most significant bit.
The result is that in native 31 bit mode each mmap request (with MAP_FIXED)
will fail where the most significat bit is set, while in compat mode it
may succeed.
This odd behaviour was introduced with d3815898 "[S390] mmap: add missing
compat_ptr conversion to both mmap compat syscalls".
To restore a consistent behaviour accross native and compat mode this
patch functionally reverts the above mentioned commit.
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The compat wrappers incorrectly called the non compat versions of
the system process_vm system calls.
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There are multiple errors in how sys_32_personality() handles personality
flags stored in top three bytes.
- directly comparing current->personality against PER_LINUX32 doesn't work
in cases when any of the personality flags stored in the top three bytes
are used.
- directly forcefully setting personality to PER_LINUX32 or PER_LINUX
discards any flags stored in the top three bytes
Fix the first one by properly using personality() macro to compare only
PER_MASK bytes.
Fix the second one by setting only the bits that should be set, instead of
overwriting the whole value.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- bring back critical fixes (esp. aa67f6096c)
- provide an updated base for development
* upstream: (4334 commits)
missed mnt_drop_write() in do_dentry_open()
UBIFS: nuke pdflush from comments
gfs2: nuke pdflush from comments
drbd: nuke pdflush from comments
nilfs2: nuke write_super from comments
hfs: nuke write_super from comments
vfs: nuke pdflush from comments
jbd/jbd2: nuke write_super from comments
btrfs: nuke pdflush from comments
btrfs: nuke write_super from comments
ext4: nuke pdflush from comments
ext4: nuke write_super from comments
ext3: nuke write_super from comments
Documentation: fix the VM knobs descritpion WRT pdflush
Documentation: get rid of write_super
vfs: kill write_super and sync_supers
ACPI processor: Fix tick_broadcast_mask online/offline regression
ACPI: Only count valid srat memory structures
ACPI: Untangle a return statement for better readability
Linux 3.6-rc1
...
Signed-off-by: Avi Kivity <avi@redhat.com>
Initialization of cra_list is currently mixed, most ciphers initialize this
field and most shashes do not. Initialization however is not needed at all
since cra_list is initialized/overwritten in __crypto_register_alg() with
list_add(). Therefore perform cleanup to remove all unneeded initializations
of this field in 'arch/s390/crypto/'
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: linux-s390@vger.kernel.org
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Merge Andrew's second set of patches:
- MM
- a few random fixes
- a couple of RTC leftovers
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (120 commits)
rtc/rtc-88pm80x: remove unneed devm_kfree
rtc/rtc-88pm80x: assign ret only when rtc_register_driver fails
mm: hugetlbfs: close race during teardown of hugetlbfs shared page tables
tmpfs: distribute interleave better across nodes
mm: remove redundant initialization
mm: warn if pg_data_t isn't initialized with zero
mips: zero out pg_data_t when it's allocated
memcg: gix memory accounting scalability in shrink_page_list
mm/sparse: remove index_init_lock
mm/sparse: more checks on mem_section number
mm/sparse: optimize sparse_index_alloc
memcg: add mem_cgroup_from_css() helper
memcg: further prevent OOM with too many dirty pages
memcg: prevent OOM with too many dirty pages
mm: mmu_notifier: fix freed page still mapped in secondary MMU
mm: memcg: only check anon swapin page charges for swap cache
mm: memcg: only check swap cache pages for repeated charging
mm: memcg: split swapin charge function into private and public part
mm: memcg: remove needless !mm fixup to init_mm when charging
mm: memcg: remove unneeded shmem charge type
...
Pull s390 updates from Martin Schwidefsky:
"This it the second batch of s390 patches for the 3.6 merge window.
Included is enablement for two common code changes, killable page
faults and sorted exception tables. And the regular set of cleanup
and bug fix patches."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: make use of user_mode() macro where possible
s390/mm: rename user_mode variable to addressing_mode
s390/mm: fix fault handling for page table walk case
s390/mm: make page faults killable
s390: update defconfig
s390/mm: downgrade page table after fork of a 31 bit process
s390/ipl: Use diagnose 8 command separation
s390/linker script: use RO_DATA_SECTION
s390/exceptions: sort exception table at build time
s390/debug: remove module_exit function / move EXPORT_SYMBOLs
Rather than #define the options manually in the architecture code, add
Kconfig options for them and select them there instead. This also allows
us to select the compat IPC version parsing automatically for platforms
using the old compat IPC interface.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE and use this instead
of the multitude of #if defined() checks in atomic64_test.c
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We use the user_mode() helper already at several places but also
have the open coded variant at other places.
Convert the code to always use the helper function.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix name clash with user_mode() define which is also used in common code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make sure the kernel does not incorrectly create a SIGBUS signal during
user space accesses:
For user space accesses in the switched addressing mode case the kernel
may walk page tables and access user address space via the kernel
mapping. If a page table entry is invalid the function __handle_fault()
gets called in order to emulate a page fault and trigger all the usual
actions like paging in a missing page etc. by calling handle_mm_fault().
If handle_mm_fault() returns with an error fixup handling is necessary.
For the switched addressing mode case all errors need to be mapped to
-EFAULT, so that the calling uaccess function can return -EFAULT to
user space.
Unfortunately the __handle_fault() incorrectly calls do_sigbus() if
VM_FAULT_SIGBUS is set. This however should only happen if a page fault
was triggered by a user space instruction. For kernel mode uaccesses
the correct action is to only return -EFAULT.
So user space may incorrectly see SIGBUS signals because of this bug.
For current machines this would only be possible for the switched
addressing mode case in conjunction with futex operations.
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is the s390 variant of 37b23e05 "x86,mm: make pagefault killable".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull crypto updates from Herbert Xu:
- Fixed algorithm construction hang when self-test fails.
- Added SHA variants to talitos AEAD list.
- New driver for Exynos random number generator.
- Performance enhancements for arc4.
- Added hwrng support to caam.
- Added ahash support to caam.
- Fixed bad kfree in aesni-intel.
- Allow aesni-intel in FIPS mode.
- Added atmel driver with support for AES/3DES/SHA.
- Bug fixes for mv_cesa.
- CRC hardware driver for BF60x family processors.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (66 commits)
crypto: twofish-avx - remove useless instruction
crypto: testmgr - add aead cbc aes hmac sha1,256,512 test vectors
crypto: talitos - add sha224, sha384 and sha512 to existing AEAD algorithms
crypto: talitos - export the talitos_submit function
crypto: talitos - move talitos structures to header file
crypto: atmel - add new tests to tcrypt
crypto: atmel - add Atmel SHA1/SHA256 driver
crypto: atmel - add Atmel DES/TDES driver
crypto: atmel - add Atmel AES driver
ARM: AT91SAM9G45: add crypto peripherals
crypto: testmgr - allow aesni-intel and ghash_clmulni-intel in fips mode
hwrng: exynos - Add support for Exynos random number generator
crypto: aesni-intel - fix wrong kfree pointer
crypto: caam - ERA retrieval and printing for SEC device
crypto: caam - Using alloc_coherent for caam job rings
crypto: algapi - Fix hang on crypto allocation
crypto: arc4 - now arc needs blockcipher support
crypto: caam - one tasklet per job ring
crypto: caam - consolidate memory barriers from job ring en/dequeue
crypto: caam - only query h/w in job ring dequeue path
...
