Qdisc performance suffers when packets are dropped at enqueue()
time because drops (kfree_skb()) are done while qdisc lock is held,
delaying a dequeue() draining the queue.
Nominal throughput can be reduced by 50 % when this happens,
at a time we would like the dequeue() to proceed as fast as possible.
Even FQ is vulnerable to this problem, while one of FQ goals was
to provide some flow isolation.
This patch adds a 'struct sk_buff **to_free' parameter to all
qdisc->enqueue(), and in qdisc_drop() helper.
I measured a performance increase of up to 12 %, but this patch
is a prereq so that future batches in enqueue() can fly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only set conntrack mark or labels when the commit flag is specified.
This makes sure we can not set them before the connection has been
persisted, as in that case the mark and labels would be lost in an
event of an userspace upcall.
OVS userspace already requires the commit flag to accept setting
ct_mark and/or ct_labels. Validate for this in the kernel API.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set conntrack mark and labels right before committing so that
the initial conntrack NEW event has the mark and labels.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit f2a4d086ed ("openvswitch: Add packet truncation support.")
introduces packet truncation before sending to userspace upcall receiver.
This patch passes up the skb->len before truncation so that the upcall
receiver knows the original packet size. Potentially this will be used
by sFlow, where OVS translates sFlow config header=N to a sample action,
truncating packet to N byte in kernel datapath. Thus, only N bytes instead
of full-packet size is copied from kernel to userspace, saving the
kernel-to-userspace bandwidth.
Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Pravin Shelar <pshelar@nicira.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving an ICMPv4 message containing extensions as
defined in RFC 4884, and translating it to ICMPv6 at SIT
or GRE tunnel, we need some extra manipulation in order
to properly forward the extensions.
This patch only takes care of Time Exceeded messages as they
are the ones that typically carry information from various
routers in a fabric during a traceroute session.
It also avoids complex skb logic if the data_len is not
a multiple of 8.
RFC states :
The "original datagram" field MUST contain at least 128 octets.
If the original datagram did not contain 128 octets, the
"original datagram" field MUST be zero padded to 128 octets.
In practice routers use 128 bytes of original datagram, not more.
Initial translation was added in commit ca15a078bd
("sit: generate icmpv6 error when receiving icmpv4 error")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Oussama Ghorbel <ghorbel@pivasoftware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipgre_err() can call ip6_err_gen_icmpv6_unreach() for proper
support of ipv4+gre+icmp+ipv6+... frames, used for example
by traceroute/mtr.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For better traceroute/mtr support for SIT and GRE tunnels,
we translate IPV4 ICMP ICMP_TIME_EXCEEDED to ICMPV6_TIME_EXCEED
We also have to translate the IPv4 source IP address of ICMP
message to IPv6 v4mapped.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to use this helper from GRE as well, so this is
the time to move it in net/ipv6/icmp.c
Also add a @nhs parameter, since SIT and GRE have different
values for the header(s) to skip.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIT or GRE tunnels might want to translate an IPV4 address
into a v4mapped one when translating ICMP to ICMPv6.
This patch adds the parameter to icmp6_send() but
does not change icmpv6_send() signature.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
net/rds/tcp.c:59:5: warning:
symbol 'rds_tcp_min_sndbuf' was not declared. Should it be static?
net/rds/tcp.c:60:5: warning:
symbol 'rds_tcp_min_rcvbuf' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJXZAIqAAoJED07qiWsqSVqW0YH/RMgC6CDlJUtHr7+B8YLpi0e
BZOzAHH7mQdP+Z2kIXZp8Dnziq5G8heWNjRwTMPLHvOel+oms+0ZK6VY/kJYArdb
ViGGgi/gQ334JGqJYi2utkyIIIRH7ZxwcblF1aaaFVfFy7tZMVuppIWVzR/V0Gje
/5FftT1f04/6iumEq4es+Jb0OC9azoebSs1DUZTIvYOz3XrnCbB1FdmDN+a3xZKC
Qyav6QVnp/m2InzGSN+Kd/W++EP6YckdBp/++2hizsOvSIOfe8GRqkc0r7fLbfZ8
rucDJNi+GrLat4wNza4t3FKf3rBenBFzii14OEUTE0JgpY90fGUF3n/i0duaB/k=
=90Ns
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.8-20160617' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2016-06-17
this is a pull request of 14 patches for net-next/master.
Geert Uytterhoeven contributes a patch that adds a file patterns for
CAN device tree bindings to MAINTAINERS. A patch by Alexander Aring
fixes warnings when building without proc support. A patch by me
improves the sample point calculation. Marek Vasut's patch converts
the slcan driver to use CAN_MTU. A patch by William Breathitt Gray
converts the tscan1 driver to use module_isa_driver.
Two patches by Maximilian Schneider for the gs_usb driver fix coding
style and add support for set_phys_id callback. 5 patches by Oliver
Hartkopp add support for CANFD to the bcm. And finally two patches
by Ramesh Shanmugasundaram, which add support for the rcar_canfd
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
"up_map" is a u64 type but we're not using the high 32 bits.
Fixes: 35c55c9877 ('tipc: add neighbor monitoring framework')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 version of 3f2fb9a834 ("net: l3mdev: address selection should only
consider devices in L3 domain") and the follow up commit, a17b693cdd876
("net: l3mdev: prefer VRF master for source address selection").
That is, if outbound device is given then the address preference order
is an address from that device, an address from the master device if it
is enslaved, and then an address from a device in the same L3 domain.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 source address selection needs to consider the real egress route.
Similar to IPv4 implement a get_saddr6 method which is called if
source address has not been set. The get_saddr6 method does a full
lookup which means pulling a route from the VRF FIB table and properly
considering linklocal/multicast destination addresses. Lookup failures
(eg., unreachable) then cause the source address selection to fail
which gets propagated back to the caller.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VRF driver needs access to ip6_route_get_saddr code. Since it does
little beyond ipv6_dev_get_saddr and ipv6_dev_get_saddr is already
exported for modules move ip6_route_get_saddr to the header as an
inline.
Code move only; no functional change.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have all the drivers using udp_tunnel_get_rx_ports,
ndo_add_udp_enc_rx_port, and ndo_del_udp_enc_rx_port we can drop the
function calls that were specific to VXLAN and GENEVE.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch merges the notifiers for VXLAN and GENEVE into a single UDP
tunnel notifier. The idea is that we will want to only have to make one
notifier call to receive the list of ports for VXLAN and GENEVE tunnels
that need to be offloaded.
In addition we add a new set of ndo functions named ndo_udp_tunnel_add and
ndo_udp_tunnel_del that are meant to allow us to track the tunnel meta-data
such as port and address family as tunnels are added and removed. The
tunnel meta-data is now transported in a structure named udp_tunnel_info
which for now carries the type, address family, and port number. In the
future this could be updated so that we can include a tuple of values
including things such as the destination IP address and other fields.
I also ended up going with a naming scheme that consisted of using the
prefix udp_tunnel on function names. I applied this to the notifier and
ndo ops as well so that it hopefully points to the fact that these are
primarily used in the udp_tunnel functions.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch merges the GENEVE and VXLAN code so that both functions pass
through a shared code path. This way we can start the effort of using a
single function on the network device drivers to handle both of these
tunnel types.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The programming API of the CAN_BCM depends on struct can_frame which is
given as array directly behind the bcm_msg_head structure. To follow this
schema for the CAN FD frames a new flag 'CAN_FD_FRAME' in the bcm_msg_head
flags indicates that the concatenated CAN frame structures behind the
bcm_msg_head are defined as struct canfd_frame.
This patch adds the support to handle CAN and CAN FD frames on a per BCM-op
base. Main changes:
- generally use struct canfd_frames instead if struct can_frames
- use canfd_frame.flags instead of can_frame.can_dlc for private BCM flags
- make all CAN frame sizes depending on the new CAN_FD_FRAME flags
- separate between CAN and CAN FD when sending/receiving frames
Due to the dependence of the CAN_FD_FRAME flag the former binary interface
for classic CAN frames remains stable.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can_frame is the name of the struct can_frame which is not meant in
the corrected comments.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When building can subsystem with CONFIG_PROC_FS=n I detected some unused
variables warning by using proc functions. In CAN the proc handling is
nicely placed in one object file. This patch adds simple add a
dependency on CONFIG_PROC_FS for CAN's proc.o file and corresponding
static inline no-op functions.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
[mkl: provide static inline noops instead of using #ifdefs]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When we check for RTM_DELTFILTER, we should also reject the request
for deleting all filters under a given parent when TCA_KIND attribute
is present. If present, it's currently just ignored but there's also
no point to let it pass in the first place either since this doesn't
have any meaning with wild-card removal.
Fixes: ea7f8277f9 ("net, cls: allow for deleting all filters for given parent")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern C standards expect the '__inline__' keyword to come before the return
type in a declaration, and we get a couple of warnings for this with "make W=1"
in the xfrm{4,6}_policy.c files:
net/ipv6/xfrm6_policy.c:369:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static int inline xfrm6_net_sysctl_init(struct net *net)
net/ipv6/xfrm6_policy.c:374:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static void inline xfrm6_net_sysctl_exit(struct net *net)
net/ipv4/xfrm4_policy.c:339:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static int inline xfrm4_net_sysctl_init(struct net *net)
net/ipv4/xfrm4_policy.c:344:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static void inline xfrm4_net_sysctl_exit(struct net *net)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The space is missing after ',', and this will introduce much more
noise when checking patch around.
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the checkpatch.pl error to dev.c:
ERROR: do not initialise statics to 0
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This appears to be necessary and sufficient to provide
MPLS in GRE (RFC4023) support.
This can be used by establishing an ipgre tunnel device
and then routing MPLS over it.
The following example will forward MPLS frames received with an outermost
MPLS label 100 over tun1, a GRE tunnel. The forwarded packet will have the
outermost MPLS LSE removed and two new LSEs added with labels 200
(outermost) and 300 (next).
ip link add name tun1 type gre remote 10.0.99.193 local 10.0.99.192 ttl 225
ip link set up dev tun1
ip addr add 10.0.98.192/24 dev tun1
ip route sh
echo 1 > /proc/sys/net/mpls/conf/eth0/input
echo 101 > /proc/sys/net/mpls/platform_labels
ip -f mpls route add 100 as 200/300 via inet 10.0.98.193
ip -f mpls route sh
Also remove unnecessary braces.
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d46e416c11 ("sctp: sctp should change socket state when
shutdown is received") may set sk_state CLOSING in sctp_sock_migrate,
but inet_accept doesn't allow the sk_state other than ESTABLISHED/
CLOSED for sctp. So we will change sk_state to CLOSED, instead of
CLOSING, as actually sk is closed already there.
Fixes: d46e416c11 ("sctp: sctp should change socket state when shutdown is received")
Reported-by: Ye Xiaolong <xiaolong.ye@intel.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HOTh
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20160615' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Rework endpoint record handling
Here's the next part of the AF_RXRPC rewrite. In this set I rework
endpoint record handling. There are two types of endpoint record, local
and peer. The local endpoint record is used as an anchor for the transport
socket that AF_RXRPC uses (at the moment a UDP socket). Local endpoints
can be shared between AF_RXRPC sockets under certain restricted
circumstances.
The peer endpoint is a record of the remote end. It is (or will be) used
to keep track MTU and RTT values and, with these changes, is used to find
the call(s) to abort when a network error occurs.
The following significant changes are made:
(1) The local endpoint event handling code is split out into its own file.
(2) The local endpoint list bottom half-excluding spinlock is removed as
things are arranged such that sk_user_data will not change whilst the
transport socket callbacks are in progress.
(3) Local endpoints can now only be shared if they have the same transport
address (as before) and have a local service ID of 0 (ie. they're not
listening for incoming calls). This prevents callbacks from a server
to one process being picked up by another process.
(4) Local endpoint destruction is now accomplished by the same work item
as processes events, meaning that the destructor doesn't need to wait
for the event processor.
(5) Peer endpoints are now held in a hash table rather than a flat list.
(6) Peer endpoints are now destroyed by RCU rather than by work item.
(7) Peer endpoints are now differentiated by local endpoint and remote
transport port in addition to remote transport address and transport
type and family.
This means that a firewall that excludes access between a particular
local port and remote port won't cause calls to be aborted that use a
different port pair.
(8) Error report handling now no longer assumes that the source is always
an IPv4 ICMP message from a UDP port and has assumptions that an ICMP
message comes from an IPv4 socket removed. At some point IPv6 support
will be added.
(9) Peer endpoints rather than local endpoints are now the anchor point
for distributing network error reports.
(10) Both types of endpoint records are now disposed of as soon as all
references to them are gone. There is less hanging around and once
their usage counts hit zero, records can no longer be resurrected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The algorithm for checksum neutral mapping is incorrect. This problem
was being hidden since we were previously always performing checksum
offload on the translated addresses and only with IPv6 HW csum.
Enabling an ILA router shows the issue.
Corrected algorithm:
old_loc is the original locator in the packet, new_loc is the value
to overwrite with and is found in the lookup table. old_flag is
the old flag value (zero of CSUM_NEUTRAL_FLAG) and new_flag is
then (old_flag ^ CSUM_NEUTRAL_FLAG) & CSUM_NEUTRAL_FLAG.
Need SUM(new_id + new_flag + diff) == SUM(old_id + old_flag) for
checksum neutral translation.
Solving for diff gives:
diff = (old_id - new_id) + (old_flag - new_flag)
compute_csum_diff8(new_id, old_id) gives old_id - new_id
If old_flag is set
old_flag - new_flag = old_flag = CSUM_NEUTRAL_FLAG
Else
old_flag - new_flag = -new_flag = ~CSUM_NEUTRAL_FLAG
Tested:
- Implemented a user space program that creates random addresses
and random locators to overwrite. Compares the checksum over
the address before and after translation (must always be equal)
- Enabled ILA router and showed proper operation.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the presence of firewalls which improperly block ICMP Unreachable
(including Fragmentation Required) messages, Path MTU Discovery is
prevented from working.
A workaround is to handle IPv4 payloads opaquely, ignoring the DF bit--as
is done for other payloads like AppleTalk--and doing transparent
fragmentation and reassembly.
Redux includes the enforcement of mutual exclusion between this feature
and Path MTU Discovery as suggested by Alexander Duyck.
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds necessary handling for use the short address for
802.15.4 6lowpan. It contains support for IPHC address compression
and new matching algorithmn to decide which link layer address will be
used for 802.15.4 frame.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of sending RA messages we need some way to get the short address
from an 802.15.4 6LoWPAN interface. This patch will add a temporary
debugfs entry for experimental userspace api.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduce different 6lowpan handling for receive and transmit
NS/NA messages for the ipv6 neighbour discovery. The first use-case is
for supporting 802.15.4 short addresses inside the option fields and
handling for RFC6775 6CO option field as userspace option.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports some neighbour discovery functions which can be used
by 6lowpan neighbour discovery ops functionality then.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces neighbour discovery ops callback structure. The
idea is to separate the handling for 6LoWPAN into the 6lowpan module.
These callback offers 6lowpan different handling, such as 802.15.4 short
address handling or RFC6775 (Neighbor Discovery Optimization for IPv6
over 6LoWPANs).
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the functionality to add a RA PIO prefix generated
address in an own function. This move prepares to add a hook for
adding a second address for a second link-layer address. E.g. short
address for 802.15.4 6LoWPAN.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds __ndisc_fill_addr_option as low-level function for
ndisc_fill_addr_option which doesn't depend on net_device parameter.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we use exported function from ipv6 kernel module we don't need to
request the module anymore to have ipv6 functionality.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the autoconfiguration if a valid 802.15.4 short address
is available for 802.15.4 6LoWPAN interfaces.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will introduce a 6lowpan neighbour private data. Like the
interface private data we handle private data for generic 6lowpan and
for link-layer specific 6lowpan.
The current first use case if to save the short address for a 802.15.4
6lowpan neighbour.
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
sfq_reset() can use rtnl_kfree_skbs() instead of kfree_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pie_change() can use rtnl_qdisc_drop() to benefit from
deferred freeing.
pie_reset() is already using qdisc_reset_queue()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_kfree_skbs() can be used in tfifo_reset()
It would be nice if we could iterate through rb tree instead
of removing one skb at a time, and build a single skb chain.
But this is left for a future patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both htb_reset() and htb_destroy() can use __qdisc_reset_queue()
instead of __skb_queue_purge() to defer skb freeing of internal
queues.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both hhf_reset() and hhf_change() can use rtnl_kfree_skbs()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both fq_codel_change() and fq_codel_reset() can use rtnl_kfree_skbs()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both fq_change() and fq_reset() can use rtnl_kfree_skbs()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
codel_change() can use rtnl_qdisc_drop()
to defer expensive skb freeing after locks are released.
codel_reset() already has support for deferred skb freeing
because it uses qdisc_reset_queue()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
