If driver does not support ethtool flash update operation
call into devlink.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink flash update command. Advanced NICs have firmware
stored in flash and often cryptographically secured. Updating
that flash is handled by management firmware. Ethtool has a
flash update command which served us well, however, it has two
shortcomings:
- it takes rtnl_lock unnecessarily - really flash update has
nothing to do with networking, so using a networking device
as a handle is suboptimal, which leads us to the second one:
- it requires a functioning netdev - in case device enters an
error state and can't spawn a netdev (e.g. communication
with the device fails) there is no netdev to use as a handle
for flashing.
Devlink already has the ability to report the firmware versions,
now with the ability to update the firmware/flash we will be
able to recover devices in bad state.
To enable updates of sub-components of the FW allow passing
component name. This name should correspond to one of the
versions reported in devlink info.
v1: - replace target id with component name (Jiri).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-02-16
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) numerous libbpf API improvements, from Andrii, Andrey, Yonghong.
2) test all bpf progs in alu32 mode, from Jiong.
3) skb->sk access and bpf_sk_fullsock(), bpf_tcp_sock() helpers, from Martin.
4) support for IP encap in lwt bpf progs, from Peter.
5) remove XDP_QUERY_XSK_UMEM dead code, from Jan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of flow_stats_update(), drivers now update the stats
fields of the passed tc_cls_flower_offload struct, rather than call
tcf_exts_stats_update() directly to update the stats of offloaded TC
flower rules. However, if multiple qdiscs are registered to a TC shared
block and a flower rule is applied, then, when getting stats for the rule,
multiple callbacks may be made.
Take this into consideration by modifying flow_stats_update to gather the
stats from all callbacks. Currently, the values in tc_cls_flower_offload
only account for the last stats callback in the list.
Fixes: 3b1903ef97 ("flow_offload: add statistics retrieval infrastructure and use it")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With many active TCP sockets, fat TCP sockets could fool
__sk_mem_raise_allocated() thanks to an overflow.
They would increase their share of the memory, instead
of decreasing it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Proxy ip6_route_input via ipv6_stub, for later use by lwt bpf ip encap
(see the next patch in the patchset).
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Implement BPF_LWT_ENCAP_IP mode in bpf_lwt_push_encap BPF helper.
It enables BPF programs (specifically, BPF_PROG_TYPE_LWT_IN and
BPF_PROG_TYPE_LWT_XMIT prog types) to add IP encapsulation headers
to packets (e.g. IP/GRE, GUE, IPIP).
This is useful when thousands of different short-lived flows should be
encapped, each with different and dynamically determined destination.
Although lwtunnels can be used in some of these scenarios, the ability
to dynamically generate encap headers adds more flexibility, e.g.
when routing depends on the state of the host (reflected in global bpf
maps).
v7 changes:
- added a call skb_clear_hash();
- removed calls to skb_set_transport_header();
- refuse to encap GSO-enabled packets.
v8 changes:
- fix build errors when LWT is not enabled.
Note: the next patch in the patchset with deal with GSO-enabled packets,
which are currently rejected at encapping attempt.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Extend Qdisc_class_ops with flags. Create enum to hold possible class ops
flag values. Add first class ops flags value QDISC_CLASS_OPS_DOIT_UNLOCKED
to indicate that class ops functions can be called without taking rtnl
lock.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'rtnl_held' flag to tcf proto change, delete, destroy, dump, walk
functions to track rtnl lock status. Extend users of these function in cls
API to propagate rtnl lock status to them. This allows classifiers to
obtain rtnl lock when necessary and to pass rtnl lock status to extensions
and driver offload callbacks.
Add flags field to tcf proto ops. Add flag value to indicate that
classifier doesn't require rtnl lock.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add optional tp->ops->put() API to be implemented for filter reference
counting. This new function is called by cls API to release filter
reference for filters returned by tp->ops->change() or tp->ops->get()
functions. Implement tfilter_put() helper to call tp->ops->put() only for
classifiers that implement it.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Actions API is already updated to not rely on rtnl lock for
synchronization. However, it need to be provided with rtnl status when
called from classifiers API in order to be able to correctly release the
lock when loading kernel module.
Extend extension validation function with 'rtnl_held' flag which is passed
to actions API. Add new 'rtnl_held' parameter to tcf_exts_validate() in cls
API. No classifier is currently updated to support unlocked execution, so
pass hardcoded 'true' flag parameter value.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend tcf_chain with 'flushing' flag. Use the flag to prevent insertion of
new classifier instances when chain flushing is in progress in order to
prevent resource leak when tcf_proto is created by unlocked users
concurrently.
Return EAGAIN error from tcf_chain_tp_insert_unique() to restart
tc_new_tfilter() and lookup the chain/proto again.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement unique insertion function to atomically attach tcf_proto to chain
after verifying that no other tcf proto with specified priority exists.
Implement delete function that verifies that tp is actually empty before
deleting it. Use these functions to refactor cls API to account for
concurrent tp and rule update instead of relying on rtnl lock. Add new
'deleting' flag to tcf proto. Use it to restart search when iterating over
tp's on chain to prevent accessing potentially inval tp->next pointer.
Extend tcf proto with spinlock that is intended to be used to protect its
data from concurrent modification instead of relying on rtnl mutex. Use it
to protect 'deleting' flag. Add lockdep macros to validate that lock is
held when accessing protected fields.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users of chain->filters_chain rely on rtnl lock and assume that no new
classifier instances are added when traversing the list. Use
tcf_get_next_proto() to traverse filters list without relying on rtnl
mutex. This function iterates over classifiers by taking reference to
current iterator classifier only and doesn't assume external
synchronization of filters list.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to remove dependency on rtnl lock and allow concurrent tcf_proto
modification, extend tcf_proto with reference counter. Implement helper
get/put functions for tcf proto and use them to modify cls API to always
take reference to tcf_proto while using it. Only release reference to
parent chain after releasing last reference to tp.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend tcf_chain with new filter_chain_lock mutex. Always lock the chain
when accessing filter_chain list, instead of relying on rtnl lock.
Dereference filter_chain with tcf_chain_dereference() lockdep macro to
verify that all users of chain_list have the lock taken.
Rearrange tp insert/remove code in tc_new_tfilter/tc_del_tfilter to execute
all necessary code while holding chain lock in order to prevent
invalidation of chain_info structure by potential concurrent change. This
also serializes calls to tcf_chain0_head_change(), which allows head change
callbacks to rely on filter_chain_lock for synchronization instead of rtnl
mutex.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users of block->chain_list rely on rtnl lock and assume that no new
chains are added when traversing the list. Use tcf_get_next_chain() to
traverse chain list without relying on rtnl mutex. This function iterates
over chains by taking reference to current iterator chain only and doesn't
assume external synchronization of chain list.
Don't take reference to all chains in block when flushing and use
tcf_get_next_chain() to safely iterate over chain list instead. Remove
tcf_block_put_all_chains() that is no longer used.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, tcf_block doesn't use any synchronization mechanisms to protect
critical sections that manage lifetime of its chains. block->chain_list and
multiple variables in tcf_chain that control its lifetime assume external
synchronization provided by global rtnl lock. Converting chain reference
counting to atomic reference counters is not possible because cls API uses
multiple counters and flags to control chain lifetime, so all of them must
be synchronized in chain get/put code.
Use single per-block lock to protect block data and manage lifetime of all
chains on the block. Always take block->lock when accessing chain_list.
Chain get and put modify chain lifetime-management data and parent block's
chain_list, so take the lock in these functions. Verify block->lock state
with assertions in functions that expect to be called with the lock taken
and are called from multiple places. Take block->lock when accessing
filter_chain_list.
In order to allow parallel update of rules on single block, move all calls
to classifiers outside of critical sections protected by new block->lock.
Rearrange chain get and put functions code to only access protected chain
data while holding block lock:
- Rearrange code to only access chain reference counter and chain action
reference counter while holding block lock.
- Extract code that requires block->lock from tcf_chain_destroy() into
standalone tcf_chain_destroy() function that is called by
__tcf_chain_put() in same critical section that changes chain reference
counters.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit b639583f9e.
As per discussion with Jakub Kicinski and Michal Kubecek,
this will be better addressed by soon-too-come ethtool netlink
API with additional indication that given configuration request
is supposed to be persisted.
Also, remove the parameter support from bnxt_en driver.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Michal Kubecek <mkubecek@suse.cz>
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implementation of macro "flow_action_for_each" introduced in
commit e3ab786b42 ("flow_offload: add flow action infrastructure")
and used in commit 7386788175 ("drivers: net: use flow action
infrastructure") iterated the first item twice and did not reach the
last one. Fix it.
Fixes: e3ab786b42 ("flow_offload: add flow action infrastructure")
Fixes: 7386788175 ("drivers: net: use flow action infrastructure")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
At Jiri's suggestion add a generic "board.manufacture"
version identifier.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the kernel users of the TCA_ACT_* macros to use TCA_ID_*. For
example, use TCA_ID_GACT instead of TCA_ACT_GACT. This will align with
TCA_ID_POLICE and also differentiates these identifier, used in struct
tc_action_ops type field, from other macros starting with TCA_ACT_.
To make things clearer, we name the enum defining the TCA_ID_*
identifiers and also change the "type" field of struct tc_action to
id.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the algorithm described in the comment block at the
beginning of ip_rt_send_redirect, the host should try to send
'ip_rt_redirect_number' ICMP redirect packets with an exponential
backoff and then stop sending them at all assuming that the destination
ignores redirects.
If the device has previously sent some ICMP error packets that are
rate-limited (e.g TTL expired) and continues to receive traffic,
the redirect packets will never be transmitted. This happens since
peer->rate_tokens will be typically greater than 'ip_rt_redirect_number'
and so it will never be reset even if the redirect silence timeout
(ip_rt_redirect_silence) has elapsed without receiving any packet
requiring redirects.
Fix it by using a dedicated counter for the number of ICMP redirect
packets that has been sent by the host
I have not been able to identify a given commit that introduced the
issue since ip_rt_send_redirect implements the same rate-limiting
algorithm from commit 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user can do dump or get of param values right after the
devlink params are registered. However the driver may not be initialized
which is an issue. The same problem happens during notification
upon param registration. Allow driver to publish devlink params
whenever it is ready to handle get() ops. Note that this cannot
be resolved by init reordering, as the "driverinit" params have
to be available before the driver is initialized (it needs the param
values there).
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon error discover, every driver can report it to the devlink health
mechanism via devlink_health_report function, using the appropriate
reporter registered to it. Driver can pass error specific context which
will be delivered to it as part of the dump / recovery callbacks.
Once an error is reported, devlink health will do the following actions:
* A log is being send to the kernel trace events buffer
* Health status and statistics are being updated for the reporter instance
* Object dump is being taken and stored at the reporter instance (as long
as there is no other dump which is already stored)
* Auto recovery attempt is being done. Depends on:
- Auto Recovery configuration
- Grace period vs. Time since last recover
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink health reporter is an instance for reporting, diagnosing and
recovering from run time errors discovered by the reporters.
Define it's data structure and supported operations.
In addition, expose devlink API to create and destroy a reporter.
Each devlink instance will hold it's own reporters list.
As part of the allocation, driver shall provide a set of callbacks which
will be used by devlink in order to handle health reports and user
commands related to this reporter. In addition, driver is entitled to
provide some priv pointer, which can be fetched from the reporter by
devlink_health_reporter_priv function.
For each reporter, devlink will hold a metadata of statistics,
dump msg and status.
For passing dumps and diagnose data to the user-space, it will use devlink
fmsg API.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink fmsg is a mechanism to pass descriptors between drivers and
devlink, in json-like format. The API allows the driver to add nested
attributes such as object, object pair and value array, in addition to
attributes such as name and value.
Driver can use this API to fill the fmsg context in a format which will be
translated by the devlink to the netlink message later.
There is no memory allocation in advance (other than the initial list
head), and it dynamically allocates messages descriptors and add them to
the list on the fly.
When it needs to send the data using SKBs to the netlink layer, it
fragments the data between different SKBs. In order to do this
fragmentation, it uses virtual nests attributes, to avoid actual
nesting use which cannot be divided between different SKBs.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a dedicated NDO for getting a port's parent ID, get rid
of SWITCHDEV_ATTR_ID_PORT_PARENT_ID and convert all callers to use the
NDO exclusively. This is a preliminary change to getting rid of
switchdev_ops eventually.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These actions need to be added to support the ethtool_rx_flow interface.
The queue action includes a field to specify the RSS context, that is
set via FLOW_RSS flow type flag and the rss_context field in struct
ethtool_rxnfc, plus the corresponding queue index. FLOW_RSS implies that
rss_context is non-zero, therefore, queue.ctx == 0 means that FLOW_RSS
was not set. Also add a field to store the vf index which is stored in
the ethtool_rxnfc ring_cookie field.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that drivers have been converted to use the flow action
infrastructure, remove this field from the tc_cls_flower_offload
structure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the flow_stats structure that acts as container for
tc_cls_flower_offload, then we can use to restore the statistics on the
existing TC actions. Hence, tcf_exts_stats_update() is not used from
drivers anymore.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements a new function to translate from native TC action
to the new flow_action representation. Moreover, this patch also updates
cls_flower to use this new function.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new infrastructure defines the nic actions that you can perform
from existing network drivers. This infrastructure allows us to avoid a
direct dependency with the native software TC action representation.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch wraps the dissector key and mask - that flower uses to
represent the matching side - around the flow_match structure.
To avoid a follow up patch that would edit the same LoCs in the drivers,
this patch also wraps this new flow match structure around the flow rule
object. This new structure will also contain the flow actions in follow
up patches.
This introduces two new interfaces:
bool flow_rule_match_key(rule, dissector_id)
that returns true if a given matching key is set on, and:
flow_rule_match_XYZ(rule, &match);
To fetch the matching side XYZ into the match container structure, to
retrieve the key and the mask with one single call.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anonymous sets that are bound to rules from the same transaction trigger
a kernel splat from the abort path due to double set list removal and
double free.
This patch updates the logic to search for the transaction that is
responsible for creating the set and disable the set list removal and
release, given the rule is now responsible for this. Lookup is reverse
since the transaction that adds the set is likely to be at the tail of
the list.
Moreover, this patch adds the unbind step to deliver the event from the
commit path. This should not be done from the worker thread, since we
have no guarantees of in-order delivery to the listener.
This patch removes the assumption that both activate and deactivate
callbacks need to be provided.
Fixes: cd5125d8f5 ("netfilter: nf_tables: split set destruction in deactivate and destroy phase")
Reported-by: Mikhail Morfikov <mmorfikov@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Shared buffer allocation is usually done in cell increments.
Drivers will either round up the allocation or refuse the
configuration if it's not an exact multiple of cell size.
Drivers know exactly the cell size of shared buffer, so help
out users by providing this information in dumps.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If driver did not fill the fw_version field, try to call into
the new devlink get_info op and collect the versions that way.
We assume ethtool was always reporting running versions.
v4:
- use IS_REACHABLE() to avoid problems with DEVLINK=m (kbuildbot).
v3 (Jiri):
- do a dump and then parse it instead of special handling;
- concatenate all versions (well, all that fit :)).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add defines and docs for generic info versions.
v3:
- add docs;
- separate patch (Jiri).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool -i has a few fixed-size fields which can be used to report
firmware version and expansion ROM version. Unfortunately, modern
hardware has more firmware components. There is usually some
datapath microcode, management controller, PXE drivers, and a
CPLD load. Running ethtool -i on modern controllers reveals the
fact that vendors cram multiple values into firmware version field.
Here are some examples from systems I could lay my hands on quickly:
tg3: "FFV20.2.17 bc 5720-v1.39"
i40e: "6.01 0x800034a4 1.1747.0"
nfp: "0.0.3.5 0.25 sriov-2.1.16 nic"
Add a new devlink API to allow retrieving multiple versions, and
provide user-readable name for those versions.
While at it break down the versions into three categories:
- fixed - this is the board/fixed component version, usually vendors
report information like the board version in the PCI VPD,
but it will benefit from naming and common API as well;
- running - this is the running firmware version;
- stored - this is firmware in the flash, after firmware update
this value will reflect the flashed version, while the
running version may only be updated after reboot.
v3:
- add per-type helpers instead of using the special argument (Jiri).
RFCv2:
- remove the nesting in attr DEVLINK_ATTR_INFO_VERSIONS (now
versions are mixed with other info attrs)l
- have the driver report versions from the same callback as
other info.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool -i has served us well for a long time, but its showing
its limitations more and more. The device information should
also be reported per device not per-netdev.
Lay foundation for a simple devlink-based way of reading device
info. Add driver name and device serial number as initial pieces
of information exposed via this new API.
v3:
- rename helpers (Jiri);
- rename driver name attr (Jiri);
- remove double spacing in commit message (Jiri).
RFC v2:
- wrap the skb into an opaque structure (Jiri);
- allow the serial number of be any length (Jiri & Andrew);
- add driver name (Jonathan).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we don't zerocopy if the crypto framework async bit is set.
However some crypto algorithms (such as x86 AESNI) support async,
but in the context of sendmsg, will never run asynchronously. Instead,
check for actual EINPROGRESS return code before assuming algorithm is
async.
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TLS 1.3 has minor changes from TLS 1.2 at the record layer.
* Header now hardcodes the same version and application content type in
the header.
* The real content type is appended after the data, before encryption (or
after decryption).
* The IV is xored with the sequence number, instead of concatinating four
bytes of IV with the explicit IV.
* Zero-padding: No exlicit length is given, we search backwards from the
end of the decrypted data for the first non-zero byte, which is the
content type. Currently recv supports reading zero-padding, but there
is no way for send to add zero padding.
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TLS 1.3 has a different AAD size, use a variable in the code to
make TLS 1.3 support easy.
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wire up support for 256 bit keys from the setsockopt to the crypto
framework
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the missing and malformed documentation that kernel-doc and
sphinx warn about. While at it, also add some things to the docs
to fix missing links.
Sadly, the only way I could find to fix this was to add some
trailing whitespace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the missing documentation that kernel-doc continually warns
about, to get rid of all that noise.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In typical cases, there's no need to pass both the maxattr
and the policy array pointer, as the maxattr should just be
ARRAY_SIZE(policy) - 1. Therefore, to be less error prone,
just remove the maxattr argument from the default macros
and deduce the size accordingly.
Leave the original macros with a leading underscore to use
here and in case somebody needs to pass a policy pointer
where the policy isn't declared in the same place and thus
ARRAY_SIZE() cannot be used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
