It's currently possible to bridge Ethernet tunnels carrying IP
packets directly to external interfaces without assigning them
addresses and routes on the bridged network itself: this is the case
for UDP tunnels bridged with a standard bridge or by Open vSwitch.
PMTU discovery is currently broken with those configurations, because
the encapsulation effectively decreases the MTU of the link, and
while we are able to account for this using PMTU discovery on the
lower layer, we don't have a way to relay ICMP or ICMPv6 messages
needed by the sender, because we don't have valid routes to it.
On the other hand, as a tunnel endpoint, we can't fragment packets
as a general approach: this is for instance clearly forbidden for
VXLAN by RFC 7348, section 4.3:
VTEPs MUST NOT fragment VXLAN packets. Intermediate routers may
fragment encapsulated VXLAN packets due to the larger frame size.
The destination VTEP MAY silently discard such VXLAN fragments.
The same paragraph recommends that the MTU over the physical network
accomodates for encapsulations, but this isn't a practical option for
complex topologies, especially for typical Open vSwitch use cases.
Further, it states that:
Other techniques like Path MTU discovery (see [RFC1191] and
[RFC1981]) MAY be used to address this requirement as well.
Now, PMTU discovery already works for routed interfaces, we get
route exceptions created by the encapsulation device as they receive
ICMP Fragmentation Needed and ICMPv6 Packet Too Big messages, and
we already rebuild those messages with the appropriate MTU and route
them back to the sender.
Add the missing bits for bridged cases:
- checks in skb_tunnel_check_pmtu() to understand if it's appropriate
to trigger a reply according to RFC 1122 section 3.2.2 for ICMP and
RFC 4443 section 2.4 for ICMPv6. This function is already called by
UDP tunnels
- a new function generating those ICMP or ICMPv6 replies. We can't
reuse icmp_send() and icmp6_send() as we don't see the sender as a
valid destination. This doesn't need to be generic, as we don't
cover any other type of ICMP errors given that we only provide an
encapsulation function to the sender
While at it, make the MTU check in skb_tunnel_check_pmtu() accurate:
we might receive GSO buffers here, and the passed headroom already
includes the inner MAC length, so we don't have to account for it
a second time (that would imply three MAC headers on the wire, but
there are just two).
This issue became visible while bridging IPv6 packets with 4500 bytes
of payload over GENEVE using IPv4 with a PMTU of 4000. Given the 50
bytes of encapsulation headroom, we would advertise MTU as 3950, and
we would reject fragmented IPv6 datagrams of 3958 bytes size on the
wire. We're exclusively dealing with network MTU here, though, so we
could get Ethernet frames up to 3964 octets in that case.
v2:
- moved skb_tunnel_check_pmtu() to ip_tunnel_core.c (David Ahern)
- split IPv4/IPv6 functions (David Ahern)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, processes sending traffic to a local bridge with an
encapsulation device as a port don't get ICMP errors if they exceed
the PMTU of the encapsulated link.
David Ahern suggested this as a hack, but it actually looks like
the correct solution: when we update the PMTU for a given destination
by means of updating or creating a route exception, the encapsulation
might trigger this because of PMTU discovery happening either on the
encapsulation device itself, or its lower layer. This happens on
bridged encapsulations only.
The output interface shouldn't matter, because we already have a
valid destination. Drop the output interface restriction from the
associated route lookup.
For UDP tunnels, we will now have a route exception created for the
encapsulation itself, with a MTU value reflecting its headroom, which
allows a bridge forwarding IP packets originated locally to deliver
errors back to the sending socket.
The behaviour is now consistent with IPv6 and verified with selftests
pmtu_ipv{4,6}_br_{geneve,vxlan}{4,6}_exception introduced later in
this series.
v2:
- reset output interface only for bridge ports (David Ahern)
- add and use netif_is_any_bridge_port() helper (David Ahern)
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset introduces some updates to mlx5 driver.
1) Jakub converts mlx5 to use the new udp tunnel infrastructure.
Starting with a hack to allow drivers to request a static configuration
of the default vxlan port, and then a patch that converts mlx5.
2) Parav implements change_carrier ndo for VF eswitch representors,
to speedup link state control of representors netdevices.
3) Alex Vesker, makes a simple update to software steering to fix an issue
with push vlan action sequence
4) Leon removes a redundant dump stack on error flow.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl8oRdgACgkQSD+KveBX
+j4/LQgAkSjNzOaS7bVDzhoYL3aBQOMIzgocJUeVi7xXH8IO1uy55mNDrKBqjxbW
dy9U9VsvV5i2V2qkkQLvHVkoDSg8Buo2Uxu4OrZHOLN0KfbFrra4VvmB1CzEBix8
FICnQaZZcE7529P04TgZ8Mo9vRb5VdJFhqED5Nvegy+y8FolEsQYbjIoDBE6wa0j
Meqa/29+XCE5FzTOjbbQWizAnRZMbkxtSSreDNgeHxke9eMSO+fmwKScng63QUfl
7nfU6dW6A0d1kHhpL5RqAFOcmkpSdqYaA3SA+/8pPT9X3yOAkxE6KTKGIixpB9JX
zQt+Wkna49jJ/JfDQB5vgww5c0HjAQ==
=j0fG
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-08-03
This patchset introduces some updates to mlx5 driver.
1) Jakub converts mlx5 to use the new udp tunnel infrastructure.
Starting with a hack to allow drivers to request a static configuration
of the default vxlan port, and then a patch that converts mlx5.
2) Parav implements change_carrier ndo for VF eswitch representors,
to speedup link state control of representors netdevices.
3) Alex Vesker, makes a simple update to software steering to fix an issue
with push vlan action sequence
4) Leon removes a redundant dump stack on error flow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of memory pressure, mptcp_sendmsg() may call
sk_stream_wait_memory() after succesfully xmitting some
bytes. If the latter fails we currently return to the
user-space the error code, ignoring the succeful xmit.
Address the issue always checking for the xmitted bytes
before mptcp_sendmsg() completes.
Fixes: f296234c98 ("mptcp: Add handling of incoming MP_JOIN requests")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A later patch will refuse to set the action of certain traps in mlxsw
and also to change the policer binding of certain groups. Pass extack so
that failure could be communicated clearly to user space.
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the packet trap that can report packets that were ECN marked due to RED
AQM.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/core/fib_rules.c:26:7: warning: "CONFIG_IP_MULTIPLE_TABLES" is not defined, evaluates to 0 [-Wundef]
#elif CONFIG_IP_MULTIPLE_TABLES
^~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 8b66a6fd34 ("fib: fix another fib_rules_ops indirect call wrapper problem")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-By: Brian Vazquez <brianvv@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use mptcp_for_each_subflow in mptcp_stream_accept instead of
open-coding.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* handle new SAE (WPA3 authentication) status codes in the correct way
* fix a while that should be an if instead, avoiding infinite loops
* handle beacon filtering changing better
-----BEGIN PGP SIGNATURE-----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=9iOZ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few more changes, notably:
* handle new SAE (WPA3 authentication) status codes in the correct way
* fix a while that should be an if instead, avoiding infinite loops
* handle beacon filtering changing better
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the function seg6_lwt_headroom out of the seg6_iptunnel.h uapi
header, because it is only used in seg6_iptunnel.c. Moreover, it is only
used in the kernel code, as indicated by the "#ifdef __KERNEL__".
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Ioana-Ruxandra Stăncioi <stancioi@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For retransmitted packets, TCP needs to resort to using TCP timestamps
for computing RTT samples. In the common case where the data and ACK
fall in the same 1-millisecond interval, TCP senders with millisecond-
granularity TCP timestamps compute a ca_rtt_us of 0. This ca_rtt_us
of 0 propagates to rs->rtt_us.
This value of 0 can cause performance problems for congestion control
modules. For example, in BBR, the zero min_rtt sample can bring the
min_rtt and BDP estimate down to 0, reduce snd_cwnd and result in a
low throughput. It would be hard to mitigate this with filtering in
the congestion control module, because the proper floor to apply would
depend on the method of RTT sampling (using timestamp options or
internally-saved transmission timestamps).
This fix applies a floor of 1 for the RTT sample delta from TCP
timestamps, so that seq_rtt_us, ca_rtt_us, and rs->rtt_us will be at
least 1 * (USEC_PER_SEC / TCP_TS_HZ).
Note that the receiver RTT computation in tcp_rcv_rtt_measure() and
min_rtt computation in tcp_update_rtt_min() both already apply a floor
of 1 timestamp tick, so this commit makes the code more consistent in
avoiding this edge case of a value of 0.
Signed-off-by: Jianfeng Wang <jfwang@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Kevin Yang <yyd@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using is_broadcast_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is broadcast
address.
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Huang Guobin <huangguobin4@huawei.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
1) UAF in chain binding support from previous batch, from Dan Carpenter.
2) Queue up delayed work to expire connections with no destination,
from Andrew Sy Kim.
3) Use fallthrough pseudo-keyword, from Gustavo A. R. Silva.
4) Replace HTTP links with HTTPS, from Alexander A. Klimov.
5) Remove superfluous null header checks in ip6tables, from
Gaurav Singh.
6) Add extended netlink error reporting for expression.
7) Report EEXIST on overlapping chain, set elements and flowtable
devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a missing return statement to atalk_proc_init so it doesn't return
-ENOMEM when successful. This allows the appletalk module to load
properly.
Fixes: e2bcd8b0ce ("appletalk: use remove_proc_subtree to simplify procfs code")
Link: https://www.downtowndougbrown.com/2020/08/hacking-up-a-fix-for-the-broken-appletalk-kernel-module-in-linux-5-1-and-newer/
Reported-by: Christopher KOBAYASHI <chris@disavowed.jp>
Reported-by: Doug Brown <doug@downtowndougbrown.com>
Signed-off-by: Vincent Duvert <vincent.ldev@duvert.net>
[lukas: add missing tags]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v5.1+
Cc: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we don't care about vlan depth, we could pass NULL instead of the
address of a unused local variable to skb_network_protocol() as a param.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In fact, skb_pagelen() - skb_headlen() is equal to __skb_pagelen(), use it
directly to avoid unnecessary skb_headlen() call.
Also fix the CHECK note of checkpatch.pl:
Comparison to NULL could be written "!__pskb_pull_tail"
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GRE tunnel can be used to transport traffic that does not rely on a
Internet checksum (e.g. SCTP). The issue can be triggered creating a GRE
or GRETAP tunnel and transmitting SCTP traffic ontop of it where CRC
offload has been disabled. In order to fix the issue we need to
recompute the GRE csum in gre_gso_segment() not relying on the inner
checksum.
The issue is still present when we have the CRC offload enabled.
In this case we need to disable the CRC offload if we require GRE
checksum since otherwise skb_checksum() will report a wrong value.
Fixes: 90017accff ("sctp: Add GSO support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to clear all of the bridge private skb variables as they can be
stale due to the packet being recirculated through the stack and then
transmitted through the bridge device. Similar memset is already done on
bridge's input. We've seen cases where proxyarp_replied was 1 on routed
multicast packets transmitted through the bridge to ports with neigh
suppress which were getting dropped. Same thing can in theory happen with
the port isolation bit as well.
Fixes: 821f1b21ca ("bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd flood")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"how" was used as a boolean. Change the type to bool, and improve
variable name
Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second parameter of addrconf_ifdown "how" is used as a boolean
internally. It does not make sense to call it with something different
of 0 or 1.
This value is set to 2 in all git history.
Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the masks cache size configurable, or with
a size of 0, disable it.
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a counter that counts the number of masks cache hits, and
export it through the megaflow netlink statistics.
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
info cannot be NULL here since its being accessed earlier
in the function: nlmsg_parse(info->nlhdr...). Remove this
redundant NULL check.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
ovs_ct_put_key() is potentially copying uninitialized kernel stack memory
into socket buffers, since the compiler may leave a 3-byte hole at the end
of `struct ovs_key_ct_tuple_ipv4` and `struct ovs_key_ct_tuple_ipv6`. Fix
it by initializing `orig` with memset().
Fixes: 9dd7f8907c ("openvswitch: Add original direction conntrack tuple to sw_flow_key.")
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When openvswitch conntrack offload with act_ct action. Fragment packets
defrag in the ingress tc act_ct action and miss the next chain. Then the
packet pass to the openvswitch datapath without the mru. The over
mtu packet will be dropped in output action in openvswitch for over mtu.
"kernel: net2: dropped over-mtu packet: 1528 > 1500"
This patch add mru in the tc_skb_ext for adefrag and miss next chain
situation. And also add mru in the qdisc_skb_cb. The act_ct set the mru
to the qdisc_skb_cb when the packet defrag. And When the chain miss,
The mru is set to tc_skb_ext which can be got by ovs datapath.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now skb->dev is unconditionally set to the loopback device in current net
namespace. But if we want to test bpf program which contains code branch
based on ifindex condition (eg filters out localhost packets) it is useful
to allow specifying of ifindex from userspace. This patch adds such option
through ctx_in (__sk_buff) parameter.
Signed-off-by: Dmitry Yakunin <zeil@yandex-team.ru>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200803090545.82046-3-zeil@yandex-team.ru
Now it's impossible to test all branches of cgroup_skb bpf program which
accesses skb->family and skb->{local,remote}_ip{4,6} fields because they
are zeroed during socket allocation. This commit fills socket family and
addresses from related fields in constructed skb.
Signed-off-by: Dmitry Yakunin <zeil@yandex-team.ru>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200803090545.82046-2-zeil@yandex-team.ru
mlx5 has the IANA VXLAN port (4789) hard coded by the device,
instead of being added dynamically when tunnels are created.
To support this add a workaround flag to struct udp_tunnel_nic_info.
Skipping updates for the port is fairly trivial, dumping the hard
coded port via ethtool requires some code duplication. The port
is not a part of any real table, we dump it in a special table
which has no tunnel types supported and only one entry.
This is the last known workaround / hack needed to convert
all drivers to the new infra.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mac80211.h says: Beacon filter support is advertised with the
IEEE80211_VIF_BEACON_FILTER interface capability. The driver needs to
enable beacon filter support whenever power save is enabled, that is
IEEE80211_CONF_PS is set. When power save is enabled, the stack will
not check for beacon loss and the driver needs to notify about loss
of beacons with ieee80211_beacon_loss().
Some controllers may want to dynamically enable the beacon filter
capabilities on power save entry (CONF_PS) and disable it on exit.
This is the case for the wcn36xx driver which only supports beacon
filtering in PS mode (no CONNECTION_MONITOR support).
When the mac80211 beacon monitor timer expires, the beacon filter
flag must be checked again in case it as been changed in between
(e.g. vif moved to PS mode).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1592471863-31402-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sparse showed up with the following error.
net/mac80211/agg-rx.c:480:43: warning: Using plain integer as NULL pointer
Fixes: 2ab4587675 (mac80211: add support for the ADDBA extension element)
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200803084540.179908-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SAE authentication has been extended with H2E (IEEE 802.11 REVmd) and PK
(WFA) options. Those extensions use special status code values in the
SAE commit messages (Authentication frame with transaction sequence
number 1) to identify which extension is in use. mac80211 was
interpreting those new values as the AP denying authentication and that
resulted in failure to complete SAE authentication in some cases.
Fix this by adding exceptions for the new status code values 126 and
127.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200731183830.18735-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace EBUSY by EEXIST in the following cases:
- If the user adds a chain with a different configuration such as different
type, hook and priority.
- If the user adds a non-base chain that clashes with an existing basechain.
- If the user adds a { key : value } mapping element and the key exists
but the value differs.
- If the device already belongs to an existing flowtable.
User describe that this error reporting is confusing:
- https://bugzilla.netfilter.org/show_bug.cgi?id=1176
- https://bugzilla.netfilter.org/show_bug.cgi?id=1413
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add LINK_DETACH command to force-detach bpf_link without destroying it. It has
the same behavior as auto-detaching of bpf_link due to cgroup dying for
bpf_cgroup_link or net_device being destroyed for bpf_xdp_link. In such case,
bpf_link is still a valid kernel object, but is defuncts and doesn't hold BPF
program attached to corresponding BPF hook. This functionality allows users
with enough access rights to manually force-detach attached bpf_link without
killing respective owner process.
This patch implements LINK_DETACH for cgroup, xdp, and netns links, mostly
re-using existing link release handling code.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200731182830.286260-2-andriin@fb.com
This patch extends 36dd1bcc07 ("netfilter: nf_tables: initial support
for extended ACK reporting") to include netlink extended error reporting
for expressions. This allows userspace to identify what rule expression
is triggering the error.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking fixes from David Miller:
1) Encap offset calculation is incorrect in esp6, from Sabrina Dubroca.
2) Better parameter validation in pfkey_dump(), from Mark Salyzyn.
3) Fix several clang issues on powerpc in selftests, from Tanner Love.
4) cmsghdr_from_user_compat_to_kern() uses the wrong length, from Al
Viro.
5) Out of bounds access in mlx5e driver, from Raed Salem.
6) Fix transfer buffer memleak in lan78xx, from Johan Havold.
7) RCU fixups in rhashtable, from Herbert Xu.
8) Fix ipv6 nexthop refcnt leak, from Xiyu Yang.
9) vxlan FDB dump must be done under RCU, from Ido Schimmel.
10) Fix use after free in mlxsw, from Ido Schimmel.
11) Fix map leak in HASH_OF_MAPS bpf code, from Andrii Nakryiko.
12) Fix bug in mac80211 Tx ack status reporting, from Vasanthakumar
Thiagarajan.
13) Fix memory leaks in IPV6_ADDRFORM code, from Cong Wang.
14) Fix bpf program reference count leaks in mlx5 during
mlx5e_alloc_rq(), from Xin Xiong.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (86 commits)
vxlan: fix memleak of fdb
rds: Prevent kernel-infoleak in rds_notify_queue_get()
net/sched: The error lable position is corrected in ct_init_module
net/mlx5e: fix bpf_prog reference count leaks in mlx5e_alloc_rq
net/mlx5e: E-Switch, Specify flow_source for rule with no in_port
net/mlx5e: E-Switch, Add misc bit when misc fields changed for mirroring
net/mlx5e: CT: Support restore ipv6 tunnel
net: gemini: Fix missing clk_disable_unprepare() in error path of gemini_ethernet_port_probe()
ionic: unlock queue mutex in error path
atm: fix atm_dev refcnt leaks in atmtcp_remove_persistent
net: ethernet: mtk_eth_soc: fix MTU warnings
net: nixge: fix potential memory leak in nixge_probe()
devlink: ignore -EOPNOTSUPP errors on dumpit
rxrpc: Fix race between recvmsg and sendmsg on immediate call failure
MAINTAINERS: Replace Thor Thayer as Altera Triple Speed Ethernet maintainer
selftests/bpf: fix netdevsim trap_flow_action_cookie read
ipv6: fix memory leaks on IPV6_ADDRFORM path
net/bpfilter: Initialize pos in __bpfilter_process_sockopt
igb: reinit_locked() should be called with rtnl_lock
e1000e: continue to init PHY even when failed to disable ULP
...
kernel test robot says:
net/mptcp/syncookies.c: In function 'mptcp_join_cookie_init':
include/linux/kernel.h:47:38: warning: division by zero [-Wdiv-by-zero]
#define ARRAY_SIZE(arr) (sizeof(arr) / sizeof((arr)[0]) + __must_be_array(arr))
I forgot that spinock_t size is 0 on UP, so ARRAY_SIZE cannot be used.
Fixes: 9466a1cceb ("mptcp: enable JOIN requests even if cookies are in use")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that on commit 41d707b733 ("fib: fix fib_rules_ops
indirect calls wrappers") I forgot to include the case when
CONFIG_IP_MULTIPLE_TABLES is not set.
Fixes: 41d707b733 ("fib: fix fib_rules_ops indirect calls wrappers")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes these errors:
net/ipv4/syncookies.c: In function 'tcp_get_cookie_sock':
net/ipv4/syncookies.c:216:19: error: 'struct tcp_request_sock' has no
member named 'drop_req'
216 | if (tcp_rsk(req)->drop_req) {
| ^~
net/ipv4/syncookies.c: In function 'cookie_tcp_reqsk_alloc':
net/ipv4/syncookies.c:289:27: warning: unused variable 'treq'
[-Wunused-variable]
289 | struct tcp_request_sock *treq;
| ^~~~
make[3]: *** [scripts/Makefile.build:280: net/ipv4/syncookies.o] Error 1
make[3]: *** Waiting for unfinished jobs....
Fixes: 9466a1cceb ("mptcp: enable JOIN requests even if cookies are in use")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* code cleanups and fixups as usual
* AQL & internal TXQ improvements from Felix
* some mesh 802.1X support bits
* some injection improvements from Mathy of KRACK
fame, so we'll see what this results in ;-)
* some more initial S1G supports bits, this time
(some of?) the userspace APIs
-----BEGIN PGP SIGNATURE-----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=FR6T
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2020-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a number of changes
* code cleanups and fixups as usual
* AQL & internal TXQ improvements from Felix
* some mesh 802.1X support bits
* some injection improvements from Mathy of KRACK
fame, so we'll see what this results in ;-)
* some more initial S1G supports bits, this time
(some of?) the userspace APIs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev protodown is a mechanism that allows protocols to
hold an interface down. It was initially introduced in
the kernel to hold links down by a multihoming protocol.
There was also an attempt to introduce protodown
reason at the time but was rejected. protodown and protodown reason
is supported by almost every switching and routing platform.
It was ok for a while to live without a protodown reason.
But, its become more critical now given more than
one protocol may need to keep a link down on a system
at the same time. eg: vrrp peer node, port security,
multihoming protocol. Its common for Network operators and
protocol developers to look for such a reason on a networking
box (Its also known as errDisable by most networking operators)
This patch adds support for link protodown reason
attribute. There are two ways to maintain protodown
reasons.
(a) enumerate every possible reason code in kernel
- A protocol developer has to make a request and
have that appear in a certain kernel version
(b) provide the bits in the kernel, and allow user-space
(sysadmin or NOS distributions) to manage the bit-to-reasonname
map.
- This makes extending reason codes easier (kind of like
the iproute2 table to vrf-name map /etc/iproute2/rt_tables.d/)
This patch takes approach (b).
a few things about the patch:
- It treats the protodown reason bits as counter to indicate
active protodown users
- Since protodown attribute is already an exposed UAPI,
the reason is not enforced on a protodown set. Its a no-op
if not used.
the patch follows the below algorithm:
- presence of reason bits set indicates protodown
is in use
- user can set protodown and protodown reason in a
single or multiple setlink operations
- setlink operation to clear protodown, will return -EBUSY
if there are active protodown reason bits
- reason is not included in link dumps if not used
example with patched iproute2:
$cat /etc/iproute2/protodown_reasons.d/r.conf
0 mlag
1 evpn
2 vrrp
3 psecurity
$ip link set dev vxlan0 protodown on protodown_reason vrrp on
$ip link set dev vxlan0 protodown_reason mlag on
$ip link show
14: vxlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
link/ether f6:06:be:17:91:e7 brd ff:ff:ff:ff:ff:ff protodown on <mlag,vrrp>
$ip link set dev vxlan0 protodown_reason mlag off
$ip link set dev vxlan0 protodown off protodown_reason vrrp off
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2020-07-31
The following pull-request contains BPF updates for your *net* tree.
We've added 5 non-merge commits during the last 21 day(s) which contain
a total of 5 files changed, 126 insertions(+), 18 deletions(-).
The main changes are:
1) Fix a map element leak in HASH_OF_MAPS map type, from Andrii Nakryiko.
2) Fix a NULL pointer dereference in __btf_resolve_helper_id() when no
btf_vmlinux is available, from Peilin Ye.
3) Init pos variable in __bpfilter_process_sockopt(), from Christoph Hellwig.
4) Fix a cgroup sockopt verifier test by specifying expected attach type,
from Jean-Philippe Brucker.
Note that when net gets merged into net-next later on, there is a small
merge conflict in kernel/bpf/btf.c between commit 5b801dfb7f ("bpf: Fix
NULL pointer dereference in __btf_resolve_helper_id()") from the bpf tree
and commit 138b9a0511 ("bpf: Remove btf_id helpers resolving") from the
net-next tree.
Resolve as follows: remove the old hunk with the __btf_resolve_helper_id()
function. Change the btf_resolve_helper_id() so it actually tests for a
NULL btf_vmlinux and bails out:
int btf_resolve_helper_id(struct bpf_verifier_log *log,
const struct bpf_func_proto *fn, int arg)
{
int id;
if (fn->arg_type[arg] != ARG_PTR_TO_BTF_ID || !btf_vmlinux)
return -EINVAL;
id = fn->btf_id[arg];
if (!id || id > btf_vmlinux->nr_types)
return -EINVAL;
return id;
}
Let me know if you run into any others issues (CC'ing Jiri Olsa so he's in
the loop with regards to merge conflict resolution).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2020-07-31
1) Fix policy matching with mark and mask on userspace interfaces.
From Xin Long.
2) Several fixes for the new ESP in TCP encapsulation.
From Sabrina Dubroca.
3) Fix crash when the hold queue is used. The assumption that
xdst->path and dst->child are not a NULL pointer only if dst->xfrm
is not a NULL pointer is true with the exception of using the
hold queue. Fix this by checking for hold queue usage before
dereferencing xdst->path or dst->child.
4) Validate pfkey_dump parameter before sending them.
From Mark Salyzyn.
5) Fix the location of the transport header with ESP in UDPv6
encapsulation. From Sabrina Dubroca.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds TCP_NLA_EDT to SCM_TIMESTAMPING_OPT_STATS that reports
the earliest departure time(EDT) of the timestamped skb. By tracking EDT
values of the skb from different timestamps, we can observe when and how
much the value changed. This allows to measure the precise delay
injected on the sender host e.g. by a bpf-base throttler.
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
JOIN requests do not work in syncookie mode -- for HMAC validation, the
peers nonce and the mptcp token (to obtain the desired connection socket
the join is for) are required, but this information is only present in the
initial syn.
So either we need to drop all JOIN requests once a listening socket enters
syncookie mode, or we need to store enough state to reconstruct the request
socket later.
This adds a state table (1024 entries) to store the data present in the
MP_JOIN syn request and the random nonce used for the cookie syn/ack.
When a MP_JOIN ACK passed cookie validation, the table is consulted
to rebuild the request socket from it.
An alternate approach would be to "cancel" syn-cookie mode and force
MP_JOIN to always use a syn queue entry.
However, doing so brings the backlog over the configured queue limit.
v2: use req->syncookie, not (removed) want_cookie arg
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SYN packet contains MP_CAPABLE option, keep it enabled.
Syncokie validation and cookie-based socket creation is changed to
instantiate an mptcp request sockets if the ACK contains an MPTCP
connection request.
Rather than extend both cookie_v4/6_check, add a common helper to create
the (mp)tcp request socket.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
