When an array is reshaped to have fewer devices, the reshape proceeds
from the end of the devices to the beginning.
If a device happens to be non-In_sync (which is possible but rare)
we would normally update the ->recovery_offset as the reshape
progresses. However that would be wrong as the recover_offset records
that the early part of the device is in_sync, while in fact it would
only be the later part that is in_sync, and in any case the offset
number would be measured from the wrong end of the device.
Relatedly, if after a reshape a spare is discovered to not be
recoverred all the way to the end, not allow spare_active
to incorporate it in the array.
This becomes relevant in the following sample scenario:
A 4 drive RAID5 is converted to a 6 drive RAID6 in a combined
operation.
The RAID5->RAID6 conversion will cause a 5 drive to be included as a
spare, then the 5drive -> 6drive reshape will effectively rebuild that
spare as it progresses. The 6th drive is treated as in_sync the whole
time as there is never any case that we might consider reading from
it, but must not because there is no valid data.
If we interrupt this reshape part-way through and reverse it to return
to a 5-drive RAID6 (or event a 4-drive RAID5), we don't want to update
the recovery_offset - as that would be wrong - and we don't want to
include that spare as active in the 5-drive RAID6 when the reversed
reshape completed and it will be mostly out-of-sync still.
Signed-off-by: NeilBrown <neilb@suse.de>
The entries in the stripe_cache maintained by raid5 are enlarged
when we increased the number of devices in the array, but not
shrunk when we reduce the number of devices.
So if entries are added after reducing the number of devices, we
much ensure to initialise the whole entry, not just the part that
is currently relevant. Otherwise if we enlarge the array again,
we will reference uninitialised values.
As grow_buffers/shrink_buffer now want to use a count that is stored
explicity in the raid_conf, they should get it from there rather than
being passed it as a parameter.
Signed-off-by: NeilBrown <neilb@suse.de>
Only level 5 with layout=PARITY_N can be taken over to raid0 now.
Lets allow level 4 either.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
After takeover from raid5/10 -> raid0 mddev->layout is not cleared.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Use mddev->new_layout in setup_conf.
Also use new_chunk, and don't set ->degraded in takeover(). That
gets set in run()
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Most array level changes leave the list of devices largely unchanged,
possibly causing one at the end to become redundant.
However conversions between RAID0 and RAID10 need to renumber
all devices (except 0).
This renumbering is currently being done in the ->run method when the
new personality takes over. However this is too late as the common
code in md.c might already have invalidated some of the devices if
they had a ->raid_disk number that appeared to high.
Moving it into the ->takeover method is too early as the array is
still active at that time and wrong ->raid_disk numbers could cause
confusion.
So add a ->new_raid_disk field to mdk_rdev_s and use it to communicate
the new raid_disk number.
Now the common code knows exactly which devices need to be renumbered,
and which can be invalidated, and can do it all at a convenient time
when the array is suspend.
It can also update some symlinks in sysfs which previously were not be
updated correctly.
Reported-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Such NULL pointer dereference can occur when the driver was fixing the
read errors/bad blocks and the disk was physically removed
causing a system crash. This patch check if the
rcu_dereference() returns valid rdev before accessing it in fix_read_error().
Cc: stable@kernel.org
Signed-off-by: Prasanna S. Panchamukhi <prasanna.panchamukhi@riverbed.com>
Signed-off-by: Rob Becker <rbecker@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Commit b821eaa572 broke partition
detection for md arrays.
The logic was almost right. However if revalidate_disk is called
when the device is not yet open, bdev->bd_disk won't be set, so the
flush_disk() Call will not set bd_invalidated.
So when md_open is called we still need to ensure that
->bd_invalidated gets set. This is easily done with a call to
check_disk_size_change in the place where the offending commit removed
check_disk_change. At the important times, the size will have changed
from 0 to non-zero, so check_disk_size_change will set bd_invalidated.
Tested-by: Duncan <1i5t5.duncan@cox.net>
Reported-by: Duncan <1i5t5.duncan@cox.net>
Signed-off-by: NeilBrown <neilb@suse.de>
sky2_phy_reinit is called by the ethtool helpers sky2_set_settings,
sky2_nway_reset and sky2_set_pauseparam when netif_running.
However, at the end of sky2_phy_init GM_GP_CTRL has GM_GPCR_RX_ENA and
GM_GPCR_TX_ENA cleared. So, doing these commands causes the device to
stop working:
$ ethtool -r eth0
$ ethtool -A eth0 autoneg off
Fix this issue by enabling Rx/Tx after running sky2_phy_init in
sky2_phy_reinit.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Tested-by: Brandon Philips <bphilips@suse.de>
Cc: stable@kernel.org
Tested-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're moving the mailing list to linux-cifs@vger.kernel.org.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Disable statistics initialization for eth clients that do not support
statistics. This prevents memory corruption on bnx2x hw.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
netxen_nic and qlcnic driver depends on firmware_class module.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit aa2ea0586d (tcp: fix outsegs stat for TSO segments) incorrectly
assumed SNMP_ADD_STATS() was used from BH context.
Fix this using mib[!in_softirq()] instead of mib[0]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio-pci resets the device at startup by writing to the status
register, but this does not clear the pci config space,
specifically msi enable status which affects register
layout.
This breaks things like kdump when they try to use e.g. virtio-blk.
Fix by forcing msi off at startup. Since pci.c already has
a routine to do this, we export and use it instead of duplicating code.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
add_buf returns ring size on out of memory,
this is not what devices expect.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org # .34.x
Cintiq 21UX2 added 8 more bits for the tool serial number and more
buttons for the expresskey. We did not enable them properly in the
last patch.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some of the recent X86_MRST additions make some "select"s
conditional on X86_MRST but missed some related kconfig symbols,
causing:
drivers/built-in.o: In function `ps2_end_command':
(.text+0x257ab2): undefined reference to `i8042_check_port_owner'
drivers/built-in.o: In function `ps2_end_command':
(.text+0x257ae1): undefined reference to `i8042_unlock_chip'
drivers/built-in.o: In function `ps2_begin_command':
(.text+0x257b40): undefined reference to `i8042_check_port_owner'
drivers/built-in.o: In function `ps2_begin_command':
(.text+0x257b6f): undefined reference to `i8042_lock_chip'
when SERIO_I8042=m, SERIO_LIBPS2=y, KEYBOARD_ATKBD=y.
We need to make i8042 dependant upon !X86_MRST and allow deselecting
atkbd on Moorestown even when !CONFIG_EMBEDDED.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Apparently, we have never been able to set the atime correctly from the
NFSv4 client.
Reported-by: 小倉一夫 <ka-ogura@bd6.so-net.ne.jp>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Currently, we do not display the minor version mount parameter in the
/proc mount info.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Put the code that is common to both the referral and ordinary mount cases
into a common helper routine.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If the attempt to read the calldir fails, then instead of storing the read
bytes, we currently discard them. This leads to a garbage final result when
upon re-entry to the same routine, we read the remaining bytes.
Fixes the regression in bugzilla number 16213. Please see
https://bugzilla.kernel.org/show_bug.cgi?id=16213
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
S_ISDIR(fsinfo.fattr->mode) checks the file type rather than the mode bits,
so we should be checking for the NFS_ATTR_FATTR_TYPE fattr property.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
This patch removes the setting of the low_latency flag.
tty_flip_buffer_push() is occasionally being called in irq context, which
causes a hang if the low_latency flag is set.
Removing the low_latency flag only seems to impact the flush to ldisc,
which will now be put on a workqueue.
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous CMT fixup accidentally copied in the TMU shift value, reset
this back to its original value while preserving the TMU fix.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It has been reported that the new UFO software fallback path
fails under certain conditions with NFS. I tracked the problem
down to the generation of UFO packets that are smaller than the
MTU. The software fallback path simply discards these packets.
This patch fixes the problem by not generating such packets on
the UFO path.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix commit 4cd24eaf0 (net: use netdev_mc_count and netdev_mc_empty when
appropriate)
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
$ make CONFIG_DEBUG_SECTION_MISMATCH=y
[...]
WARNING: drivers/net/built-in.o(.data+0x0): Section mismatch in reference from the variable mipsnet_driver to the function .init.text:mipsnet_probe()
The variable mipsnet_driver references
the function __init mipsnet_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
[...]
Fixed by making mipsnet_probe __devinit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/mipsnet.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found that in snd_usb_parse_audio_endpoints, there is a
dangling pointer dereference. When snd_usb_parse_audio_format fails,
fp is freed, and continue invoked. On the next loop, there is
"fp && fp->altsetting == 1 && fp->channels == 1" test, but fp is set
from the last iteration (but is bogus) and thus ilegally dereferenced.
Set fp to NULL before "continue".
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function begins and ends with a read_lock. The latter is changed to a
read_unlock.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@locked@
expression E1;
position p;
@@
read_lock(E1@p,...);
@r exists@
expression x <= locked.E1;
expression locked.E1;
expression E2;
identifier lock;
position locked.p,p1,p2;
@@
*lock@p1 (E1@p,...);
... when != E1
when != \(x = E2\|&x\)
*lock@p2 (E1,...);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit a2e066bba2 introduced core
swapping for CPU models 64 and later. I recently had a report about
a Sempron 3200+, model 95, for which this patch broke temperature
reading. It happens that this is a single-core processor, so the
effect of the swapping was to read a temperature value for a core
that didn't exist, leading to an incorrect value (-49 degrees C.)
Disabling core swapping on singe-core processors should fix this.
Additional comment from Andreas:
The BKDG says
Thermal Sensor Core Select (ThermSenseCoreSel)-Bit 2. This bit
selects the CPU whose temperature is reported in the CurTemp
field. This bit only applies to dual core processors. For
single core processors CPU0 Thermal Sensor is always selected.
k8temp_probe() correctly detected that SEL_CORE can't be used on single
core CPU. Thus k8temp did never update the temperature values stored
in temp[1][x] and -49 degrees was reported. For single core CPUs we
must use the values read into temp[0][x].
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Rick Moritz <rhavin@gmx.net>
Acked-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: stable@kernel.org
i5k_amb.ko uses dynamically allocated memory (by kmalloc) for
attributes passed to sysfs. So, sysfs_attr_init() should be called
for working happy with lockdep.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org [2.6.34 only]
When detecting AM2+ or AM3 socket with DDR2, only blacklist cores
which are known to exist in AM2+ format.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: stable@kernel.org
Commit c7f486567c
(PCI PM: PCIe PME root port service driver) causes the native PCIe
PME signaling to be used by default, if the BIOS allows the kernel to
control the standard configuration registers of PCIe root ports.
However, the native PCIe PME is coupled to the native PCIe hotplug
and calling pcie_pme_acpi_setup() makes some BIOSes expect that
the native PCIe hotplug will be used as well. That, in turn, causes
problems to appear on systems where the PCIe hotplug driver is not
loaded. The usual symptom, as reported by Jaroslav Kameník and
others, is that the ACPI GPE associated with PCIe hotplug keeps
firing continuously causing kacpid to take substantial percentage
of CPU time.
To work around this issue, change the default so that the native
PCIe PME signaling is only used if directly requested with the help
of the pcie_pme= command line switch.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15924 , which is
a listed regression from 2.6.33.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Jaroslav Kameník <jaroslav@kamenik.cz>
Tested-by: Antoni Grzymala <antekgrzymala@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
per_cpu_ptr_to_phys() determines whether the passed in @addr belongs
to the first_chunk or not by just matching the address against the
address range of the base unit (unit0, used by cpu0). When an adress
from another cpu was passed in, it will always determine that the
address doesn't belong to the first chunk even when it does. This
makes the function return a bogus physical address which may lead to
crash.
This problem was discovered by Cliff Wickman while investigating a
crash during kdump on a SGI UV system.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Cliff Wickman <cpw@sgi.com>
Tested-by: Cliff Wickman <cpw@sgi.com>
Cc: stable@kernel.org
It is common in end-node, non STP bridges to set forwarding
delay to zero; which causes the forwarding database cleanup
to run every clock tick. Change to run only as soon as needed
or at next ageing timer interval which ever is sooner.
Use round_jiffies_up macro rather than attempting round up
by changing value.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 9630bdd9b1
(ACPI: Use GPE reference counting to support shared GPEs) the wakeup
enable mask bits of GPEs are set as soon as the GPEs are enabled to
wake up the system. Unfortunately, this leads to a regression
reported by Michal Hocko, where a system is woken up from ACPI S5 by
a device that is not supposed to do that, because the wakeup enable
mask bit of this device's GPE is always set when
acpi_enter_sleep_state() calls acpi_hw_enable_all_wakeup_gpes(),
although it should only be set if the device is supposed to wake up
the system from the target state.
To work around this issue, rework the ACPI power management code so
that GPEs are not enabled to wake up the system upfront, but only
during a system state transition when the target state of the system
is known. [Of course, this means that the reference counting of
"wakeup" GPEs doesn't really make sense and it is sufficient to
set/unset the wakeup mask bits for them during system sleep
transitions. This will allow us to simplify the GPE handling code
quite a bit, but that change is too intrusive for 2.6.35.]
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15951
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
This removes dma_get_ops() prefetch optimization in bnx2.
bnx2 uses dma_get_ops() to see if dma_sync_single_for_cpu() is
noop. bnx2 does prefetch if it's noop.
But dma_get_ops() isn't available on all the architectures (only the
architectures that uses dma_map_ops struct have it). Using
dma_get_ops() in drivers leads to compilation breakage on many
architectures.
This patch removes dma_get_ops() and changes bnx2 to do prefetch on
all the architectures. This adds useless prefetch on non-coherent
architectures but this is harmless. It is also unlikely to cause the
performance drop.
[ Remove now unused local variable 'pdev' -DaveM ]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the probe() function in the at32ap700x_wdt driver, this to
make sure the miscdev is properly initialized and the driver is ready to be
accessed.
Reported-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Wim Van sebroeck <wim@iguana.be>
Fix the following two trivial bugs in pcpu_build_alloc_info()
* we should memset group_cnt to 0 by size of group_cnt, not size of
group_map (both are of the same size, so the bug isn't dangerous)
* we can delete useless variable group_cnt_max.
Signed-off-by: Pavel V. Panteleev <pp_84@mail.ru>
Signed-off-by: Tejun Heo <tj@kernel.org>
These give incorrect results for index wrap on 64 bit.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch implements a proper modification of RX skb buffers before
recycling. Adjusting only skb->data is not enough because after that
skb->tail and skb->len become incorrect.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs:
serial_cs:
add new id (TOSHIBA Modem/LAN Card)
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issuing the following command on host:
$ ifconfig eth2 mtu 1600 ; ping 10.0.0.27 -s 1485 -c 1
Makes some boards (tested with MPC8315 rev 1.1 and MPC8313 rev 1.0)
oops like this:
skb_over_panic: text:c0195914 len:1537 put:1537 head:c79e4800 data:c79e4880 tail:0xc79e4e81 end:0xc79e4e80 dev:eth1
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:127!
Oops: Exception in kernel mode, sig: 5 [#1]
MPC831x RDB
last sysfs file: /sys/kernel/uevent_seqnum
Modules linked in:
NIP: c01c1840 LR: c01c1840 CTR: c016d918
[...]
NIP [c01c1840] skb_over_panic+0x48/0x5c
LR [c01c1840] skb_over_panic+0x48/0x5c
Call Trace:
[c0339d50] [c01c1840] skb_over_panic+0x48/0x5c (unreliable)
[c0339d60] [c01c3020] skb_put+0x5c/0x60
[c0339d70] [c0195914] gfar_clean_rx_ring+0x25c/0x3d0
[c0339dc0] [c01976e8] gfar_poll+0x170/0x1bc
Dumped buffer descriptors showed that eTSEC's length/truncation
logic sometimes passes oversized packets, i.e. for the above ICMP
packet the following two buffer descriptors may become ready:
status=1400 length=1536
status=1800 length=1541
So, it seems that gianfar actually receives the whole big frame,
and it tries to place the packet into two BDs. This situation
confuses the driver, and so the skb_put() sanity check fails.
This patch fixes the issue by adding an appropriate check, i.e.
the driver should not try to process frames with buffer
descriptor's length over rx_buffer_size (i.e. maxfrm and mrblr).
Note that sometimes eTSEC works correctly, i.e. in the second
(last) buffer descriptor bits 'truncated' and 'crcerr' are set,
and so there's no oops. Though I couldn't find any logic when
it works correctly and when not.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
