Allow the MIPI-CSI data alignment to be defined in the board setup
as it may be different across various camera sensors.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add num_clients field to struct s5p_fimc_isp_info to define exactly
size of clients array which simplifies a bit the sensors management.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rework the locking in m2m driver to assure proper operation on SMP systems.
When job_abort or stop_streaming was called to immediately shutdown
a memory-to-memory transaction video buffers scheduled for processing
were never returned to vb2 and v4l2_m2m_job_finish was not called
which led to hanging.
Correct this and also return the unprocessed buffers to vb2 marking
them as erroneous, in case the end of frame interrupt do not occur.
Reported-by: Sewoon Park <seuni.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In some cases fimc H/W did not stop although there were no output
buffers available. So the capture deactivation interrupt routine
is modified and the state of ST_CAPT_RUN is cleared only
in the LAST-IRQ call.
After LAST-IRQ is generated, H/W pointer will be skipped by 1 frame.
(reference by user manual) So, S/W pointer should be increased too.
Reviewed-by Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Sungchun Kang <sungchun.kang@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Two xc5000 tuners connected to same i2c bus.
Experiments shows that situation when one tuner is not initialized
while other is tuned to channel causes TS errors.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CI reset takes several seconds on some CAM,
so there is no need to lock mutex all that time.
Also we need not to preserve CI's reset bits in
CIBUSCTRL register, they are handled automatically by FPGA.
Set it to 0 explicitly in order to not reset wrong CAM.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cpia2_core.c:529:14: warning: variable 'dir' set but not used [-Wunused-but-set-variable]
cpia2_core.c:526:5: warning: variable 'block_index' set but not used [-Wunused-but-set-variable]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
au0828-dvb.c:99:6: warning: variable 'ptr' set but not used [-Wunused-but-set-variable]
au0828-video.c:1180:25: warning: variable 'maxheight' set but not used [-Wunused-but-set-variable]
au0828-video.c:1180:15: warning: variable 'maxwidth' set but not used [-Wunused-but-set-variable]
bttv-input.c:196:16: warning: variable 'current_jiffies' set but not used [-Wunused-but-set-variable]
Those variables are not used at all, so just remove them.
Cc: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Functions defined in a header should be static inline. This prevents
compile warnings like:
'altera_ci_tuner_reset' defined but not used
(Actually appeared in the media backwards compatibility build).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/cx88/cx88-alsa.c: In function 'cx88_audio_initdev':
drivers/media/video/cx88/cx88-alsa.c:881:20: warning: 'core' may be used uninitialized in this function
The compiler doesn't understand that snd_cx88_create fills in the core
pointer. So just initialize it to NULL.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/radio/wl128x/fmdrv_common.c: In function 'recv_tasklet':
drivers/media/radio/wl128x/fmdrv_common.c:274:4: warning: format '%d' expects type 'int', but argument 4 has type 'long unsigned int'
The result of sizeof() should be printed with %zu.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/cx23885/altera-ci.c: In function 'altera_hw_filt_init':
drivers/media/video/cx23885/altera-ci.c:671:2: warning: cast from pointer to integer of different size
drivers/media/video/cx23885/altera-ci.c: In function 'altera_ci_init':
drivers/media/video/cx23885/altera-ci.c:739:2: warning: cast from pointer to integer of different size
Use %p instead of 0x%x to print addresses.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/stv0367.c: In function 'stv0367ter_lock_algo':
drivers/media/dvb/frontends/stv0367.c:1315:2: warning: cast from pointer to integer of different size
Use %p to print addresses instead of 0x%x.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/common/tuners/tuner-xc2028.c: In function 'generic_set_freq':
drivers/media/common/tuners/tuner-xc2028.c:936:15: warning: comparison between 'enum tuner_mode' and 'enum v4l2_tuner_type'
Argument type was enum tuner_mode, but should have been enum v4l2_tuner_type.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace the omap_pm_set_min_bus_tput() with a callback to board code.
This makes the omap3isp driver compilable as a module, and lets board
code manage OMAP PM details depending on board requirements.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of returning an error when receiving an ioctl call with an
unsupported command, forward the call to the subdev core::ioctl handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the VIDIOC_SUBDEV_S_CROP and G_CROP ioctls to the
userland API. CROPCAP is not implemented because it's redundant.
Signed-off-by: Antti Koskipaa <akoskipa@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The three new ioctl VIDIOC_SUBDEV_ENUM_FRAME_INTERVAL,
VIDIOC_SUBDEV_G_FRAME_INTERVAL and VIDIOC_SUBDEV_S_FRAME_INTERVAL can be
used to enumerate and configure a subdev's frame rate from userspace.
Two new video::g/s_frame_interval subdev operations are introduced to
support those ioctls. The existing video::g/s_parm operations are
deprecated and shouldn't be used anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a userspace API to get, set and enumerate the media format on a
subdev pad.
The format at the output of a subdev usually depends on the format at
its input(s). The try format operation is thus not suitable for probing
format at individual pads, as it can't modify the device state and thus
can't remember the format tried at the input to compute the output
format.
To fix the problem, pass an extra argument to the get/set format
operations to select the 'try' or 'active' format.
The try format is used when probing the subdev. Setting the try format
must not change the device configuration but can store data for later
reuse. Data storage is provided at the file-handle level so applications
probing the subdev concurently won't interfere with each other.
The active format is used when configuring the subdev. It's identical to
the format handled by the usual get/set operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 sub-devices store pad formats and crop settings in the file handle.
To let drivers initialize those settings properly, add an open operation
that is called when the subdev is opened as well as a corresponding
close operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Used for storing subdev information per file handle and hold V4L2 file
handle.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Antti Koskipaa <akoskipa@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For consistency with the V4L2_MBUS_FMT_Y10_1X10 format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 subdevices are media entities. As such they need to inherit from
(include) the media_entity structure.
When registering/unregistering the subdevice, the media entity is
automatically registered/unregistered. The entity is acquired on device
open and released on device close.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 devices are media entities. As such they need to inherit from
(include) the media_entity structure.
When registering/unregistering the device, the media entity is
automatically registered/unregistered. The entity is acquired on device
open and released on device close.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The pointer will later be used to register/unregister media entities
when registering/unregistering a v4l2_subdev or a video_device.
With the introduction of media devices, device drivers need to store a
pointer to a driver-specific structure in the device's drvdata.
v4l2_device can't claim ownership of the drvdata anymore.
To maintain compatibility with drivers that rely on v4l2_device storing
a pointer to itself in the device's drvdata, v4l2_device_register() will
keep doing so if the drvdata is NULL.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers often need to associate pipeline objects to entities, and to
take stream state into account when configuring entities and links. The
pipeline API helps drivers manage that information.
When starting streaming, drivers call media_entity_pipeline_start(). The
function marks all entities connected to the given entity through
enabled links, either directly or indirectly, as streaming. Similarly,
when stopping the stream, drivers call media_entity_pipeline_stop().
The media_entity_pipeline_start() function takes a pointer to a media
pipeline and stores it in every entity in the graph. Drivers should
embed the media_pipeline structure in higher-level pipeline structures
and can then access the pipeline through the media_entity structure.
Link configuration will fail with -EBUSY by default if either end of the
link is a streaming entity, unless the link is marked with the
MEDIA_LNK_FL_DYNAMIC flag.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create the following ioctl and implement it at the media device level to
setup links.
- MEDIA_IOC_SETUP_LINK: Modify the properties of a given link
The only property that can currently be modified is the ENABLED link
flag to enable/disable a link. Links marked with the IMMUTABLE link flag
can not be enabled or disabled.
Enabling or disabling a link has effects on entities' use count. Those
changes are automatically propagated through the graph.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create the following two ioctls and implement them at the media device
level to enumerate entities, pads and links.
- MEDIA_IOC_ENUM_ENTITIES: Enumerate entities and their properties
- MEDIA_IOC_ENUM_LINKS: Enumerate all pads and links for a given entity
Entity IDs can be non-contiguous. Userspace applications should
enumerate entities using the MEDIA_ENT_ID_FLAG_NEXT flag. When the flag
is set in the entity ID, the MEDIA_IOC_ENUM_ENTITIES will return the
next entity with an ID bigger than the requested one.
Only forward links that originate at one of the entity's source pads are
returned during the enumeration process.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create the following ioctl and implement it at the media device level to
query device information.
- MEDIA_IOC_DEVICE_INFO: Query media device information
The ioctl and its data structure are defined in the new kernel header
linux/media.h available to userspace applications.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to the wide differences between drivers regarding power management
needs, the media controller does not implement power management.
However, the media_entity structure includes a use_count field that
media drivers can use to track the number of users of every entity for
power management needs.
The use_count field is owned by media drivers and must not be touched by
entity drivers. Access to the field must be protected by the media
device graph_mutex lock.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add media entity graph traversal. The traversal follows enabled links by
depth first. Traversing graph backwards is prevented by comparing the next
possible entity in the graph with the previous one. Multiply connected
graphs are thus not supported.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As video hardware pipelines become increasingly complex and
configurable, the current hardware description through v4l2 subdevices
reaches its limits. In addition to enumerating and configuring
subdevices, video camera drivers need a way to discover and modify at
runtime how those subdevices are connected. This is done through new
elements called entities, pads and links.
An entity is a basic media hardware building block. It can correspond to
a large variety of logical blocks such as physical hardware devices
(CMOS sensor for instance), logical hardware devices (a building block
in a System-on-Chip image processing pipeline), DMA channels or physical
connectors.
A pad is a connection endpoint through which an entity can interact with
other entities. Data (not restricted to video) produced by an entity
flows from the entity's output to one or more entity inputs. Pads should
not be confused with physical pins at chip boundaries.
A link is a point-to-point oriented connection between two pads, either
on the same entity or on different entities. Data flows from a source
pad to a sink pad.
Links are stored in the source entity. To make backwards graph walk
faster, a copy of all links is also stored in the sink entity. The copy
is known as a backlink and is only used to help graph traversal.
The entity API is made of three functions:
- media_entity_init() initializes an entity. The caller must provide an
array of pads as well as an estimated number of links. The links array
is allocated dynamically and will be reallocated if it grows beyond the
initial estimate.
- media_entity_cleanup() frees resources allocated for an entity. It
must be called during the cleanup phase after unregistering the entity
and before freeing it.
- media_entity_create_link() creates a link between two entities. An
entry in the link array of each entity is allocated and stores pointers
to source and sink pads.
When a media device is unregistered, all its entities are unregistered
automatically.
The code is based on Hans Verkuil <hverkuil@xs4all.nl> initial work.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The media_device structure abstracts functions common to all kind of
media devices (v4l2, dvb, alsa, ...). It manages media entities and
offers a userspace API to discover and configure the media device
internal topology.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The media_devnode structure provides support for registering and
unregistering character devices using a dynamic major number. Reference
counting is handled internally, making device drivers easier to write
without having to solve the open/disconnect race condition issue over
and over again.
The code is based on video/v4l2-dev.c.
[mchehab@redhat.com: Remove linux/smp_lock.h include to not break compilation on bisect]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provide v4l2_subdevs with v4l2_event support. Subdev drivers only need very
little to support events.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David Cohen <dacohen@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pass the control-related ioctls to the subdev driver through the control
framework.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function isn't small or performance sensitive enough to be inlined.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create a device node named subdevX for every registered subdev.
As the device node is registered before the subdev core::s_config
function is called, return -EGAIN on open until initialization
completes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The two functions are mostly identical. They handle the copy_from_user
and copy_to_user operations related with V4L2 ioctls and call the real
ioctl handler.
Create a __video_usercopy function that implements the core of
video_usercopy and video_ioctl2, and call that function from both.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch below removes an extra "l" in the word.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch below removes an extra "l" in the word.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Related to Acorp DS120 and some revisions of DVBWorld DW2102.
If you read three or more registers at one time, you get wrong value for third etc.
Actually, it didn't affect the driver as it reads registers only by one at a time.
But it needs to correct.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prof 7500 and TeVii s630, s660, s480 works better now
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prof 7500 and TeVii s630, s660, s480 works faster now
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card consist of PCI to USB bridge and USB DVB-S2 receiver.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is taken from another tree, where it is modified.
Patch to fix that
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Simptoms:
After zapping DVB-S2 channel searching for DVB-S tooks long time.
Now it takes less than a second.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dib9000_mbx_send_attr() returns an int. It doesn't work to save
negative error codes in an unsigned char, so I've made "ret" an int
type.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This module implements V4L2 controls for the Texas Instruments
WL1273 FM Radio and handles the communication with the chip.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
RADIO_WL1273 needs to make sure that the mfd core is built to avoid
build errors:
ERROR: "mfd_add_devices" [drivers/mfd/wl1273-core.ko] undefined!
ERROR: "mfd_remove_devices" [drivers/mfd/wl1273-core.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Matti Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add suspend/resume support to the via-camera driver, so that the video
continues streaming over a suspend-resume cycle.
Originally implemented by Jon Corbet.
[mchehab@redhat.com: fix a small CodingStyle issue]
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on staging 2.6.39.
This patch is based on Veit Berwig's work.
Signed-off-by: Lukas Fisch <lukas.fisch@gmail.com>
Thanks-to: Veit Berwig <veit.Berwig@fimi.landsh.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
kmalloc() can fail so check whether state->internal is NULL.
append_internal() can return NULL on allocation failures so check that.
Also if we hit the error condition later in the function then there is
a memory leak and we need to call remove_dev() to fix it.
Also Oliver Endriss pointed out an additional leak that I missed in the
first version of this patch.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This has implementation for FM TX functionality.
It communicates with FM V4l2 module and FM common module.
Signed-off-by: Manjunatha Halli <manjunatha_halli@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This has implementation for FM RX functionality.
It communicates with FM V4l2 module and FM common module
Signed-off-by: Manjunatha Halli <manjunatha_halli@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These are the sources for the common interfaces required by the
FM V4L2 driver for TI WL127x and WL128x chips.
These implement the FM channel-8 protocol communication with the
chip. This makes use of the Shared Transport as its transport.
Signed-off-by: Manjunatha Halli <manjunatha_halli@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This module interfaces V4L2 subsystem and FM common module.
It registers itself with V4L2 as Radio module.
Signed-off-by: Manjunatha Halli <manjunatha_halli@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These are common headers used in FM submodules (FM V4L2,
FM common, FM Rx,and FM TX).
Signed-off-by: Manjunatha Halli <manjunatha_halli@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
get_user_pages() may return -errno, such as -EFAULT. So don't blindly use
its return value as an offset into dma->map[] for the next get_user_pages()
call. Since we'll give up and return an error if either fails, don't even
make the second call if the first failed to give us exactly what we were
looking for.
The old code would also call put_page() on as many elements of dma->map[]
as we'd asked for, regardless of how many were valid.
[Andy Walls modified this patch to return -EFAULT instead of -EINVAL
as Paul's observation "I'm not sure -EINVAL is the best return code vs
-EFAULT or -ENOMEM, [...]" was correct. The return value bubbles up
as a return code for write(), for which the V4L2 API spec indicates
EINVAL is incorrect and EFAULT is correct.]
Signed-off-by: Paul Cassella <fortytwo-ivtv@maneteren.bigw.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the first, botched attempt at preventing direct use of a user pointer in
ivtv_write_vbi().
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
get_user_pages() may return fewer page than we ask for. As we give up and
return an error in this case, we need to put_page() each of the pages we
did get.
[Andy Walls modified the patch, only removing the braces in the 'for'
statement, to eliminate a checkpatch warning.]
Signed-off-by: Paul Cassella <fortytwo-ivtv@manetheren.bigw.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All necessary parameters already stored in frontend cache.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Variable 'retune' does not make sense.
Loop is not needed for only one try.
Remove unnecessary dprintk's.
Remove a lot of debug messages and delays.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card consists of a PCI-e to USB Host Controller and
two TeVii S660 equivalent cards.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are two TeVii s660 modifications with different LNB power control
implementations. It is safe to call both methods for each card.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
RC keys structure for Prof 1100 already defined, so remove extra initialization.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Code changed for dw2102, stv0900 in order to achieve that.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
MarkusF wrote:
I accidently got a Terratec Cinergy S2 USB HD (instead of a Terratec Cinergy S2 PCI HD).
I found in the windows driver, that the driver is for the usb ids:
0CCD:00A8
1F4D:3000
The dvb-s2 usb adapter has the id 0CCD-00A8.
So I patches your driver and added the usb id, where the 1F4D:3000 is
and it worked (after I downloaded the firmware dvb-fe-ds3000.fw).
w_scan found the channels and vdr is working fine.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before this patch we can use only one card type from list due to
sharing one firmware name. Now it's fixed.
Also driver tries to attach only appropriate demod for this cards.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In drivers/media/dvb/ttusb-budget/dvb-ttusb-budget.c:ttusb_boot_dsp() we
need to call release_firmware(fw) before returning or we'll leak - no
matter if we succeed or fail.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Declare closed-caption setup for line 21 - this is needed for
sliced VBI capture support. (However none of that works right now
anyway.)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: The origin of the capability bounds rectangle may differ from
(left=0,top=0) so the calculation should use absolute coordinates,
here below, or use relative coordinates like
cropl_val-cap->bounds.left and cropt_val-cap->bounds.top.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Recognize and handle mode change before dealing with changes
related to the video standard. Even though the video standard should
only matter when in analog mode, doing this way is technically cleaner
in case there's other stuff that might depend on both.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This tuner PLL has missing initialisation settings resulting in
haphazard tuning. The PLL LPF was set to just 22000 symbol rate.
Basically, the module is a Sharp BS2F7HZ0194 (STV0299+IX2410)
I have had problems implementing the PLL in a new driver and
did not want to break the IX2410 out of the PLL.
This applies to DW2102, DM1105, CX88 and OPERA1 drivers.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the drivers/ieee1394/ backend was removed from firedtv, its I/O no
longer needs to be abstracted as exchangeable backend methods.
Also, ieee1394 variants of module and device probe and removal are no
longer there. Move module probe and removal into firedtv-fw.c where
device probe and removal are implemented.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Speed up tuning, as firmware is not necessary to load every attempt to tune
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Decrease firmware loading time. Before it is ~4000 i2c calls,
now it is ~256 i2c calls to load ds3000 firmware.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
TeVii s480 works fine with that on DVB-S2 channels
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make some initializations in init, not in tune function
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds audio DMA capture and ALSA mixer elements for the line
input jack of the Hauppauge Nova-S-plus DVB-S PCI card. The Nova-S-plus
has a WM8775 ADC that is currently not detected. This patch enables
this chip and exports volume, balance mute and ALC elements for ALSA
mixer controls.
[mchehab@redhat.com: Changed the patch to only talk with wm8775 if board
info says so. Also, added platform_data support, to avoid changing the
behaviour for other boards, and fixed CodingStyle]
[awalls@md.metrocast.net: Changed patch to make the WM8775_GID defintion
bridge driver private and let the bridge driver set the value of
v4l2_subdev.grp_id.]
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Add one more radio input, usefull for tm6010
Add control output amplitude.
Add set_config function for configure tuner when TV card hasn't dvb part.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add linux/sched.h because of missing declaration of TASK_NORMAL.
This patch fixes the following error:
drivers/media/video/omap24xxcam.c: In function
'omap24xxcam_vbq_complete':
drivers/media/video/omap24xxcam.c:415: error: 'TASK_NORMAL' undeclared
(first use in this function)
drivers/media/video/omap24xxcam.c:415: error: (Each undeclared
identifier is reported only once
drivers/media/video/omap24xxcam.c:415: error: for each function it
appears in.)
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the warning "Using plain integer as NULL pointer",
generated by sparse, by replacing
if (var == 0)
with
if (!var)
after an allocation
and all other offending 0s with NULL.
KernelVersion: linus' tree-1f0324c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cxhdl->priv field was not set initially, only after capturing started.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It takes too long time to scan due to low symbol rate PID's
like PAT, PMT, CAT, NIT.
For that matter we enabled permanently all PID's
less 0x20 in hardware PID filter for NetUP Dual DVB-T/C CI RF card
to combine rates.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is needed for multifrontend support.
NetUP Dual DVB-T/C CI RF card has frontends connected to port B & C
Each frontend has two switchable cores - DVB-T & DVB-C
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is two external I2C buses in cx23885 chip.
Currently, analog tuners supported for second I2C bus only
In NetUP Dual DVB-T/C CI RF card tuners connected to first bus
So, in order to support analog tuners sitting on first bus
we need modifications.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card based on cx23885 PCI-e brige. Altera FPGA for CI,
multistandard demods stv0367 from STM for QAM & OFDM, Xcieve xc5000 tuners
and additional cx25840 for second analog input.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The STV0367 is a multi-standard demodulator which is
capable of processing DVB-T as well as DVB-C signals.
It is fully compliant with DVB-T and DVB-C
recommendations for broadcast services.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
An Altera FPGA CI module for NetUP Dual DVB-T/C RF CI card.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the warning "Using plain integer as NULL pointer",
generated by sparse, by replacing the offending 0s with NULL.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This soc_camera driver is for Omnivision's OV9740 sensor. This initial
submission provides support for YUV422 output at 1280x720 (720p), which is
the sensor's native resolution. 640x480 (VGA) is also supported, with
cropping and scaling performed by the sensor's ISP.
This driver is heavily based off of the existing OV9640 driver.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that soc-camera supports videobuf API v1 and v2, camera-host drivers
can be converted to videobuf2 individually. This patch converts the
mx3_camera driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Extend soc-camera core to also support the videobuf2 API.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf2-memops and videobuf2-core can be compiled as modules, in which
case 3 more symbols from videobuf2-memops.c have to be exported.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the camera was set to output formats like RGB565 YUYV or SBGGR10,
the resulting image was scrambled due to erroneous interpretations of
horizontal parameter's units.
This patch in fourcc_to_ipu_pix, eliminate also the pixel formats mappings
that, first are not used within mainline code and second, standing at
the datasheets, they will not work properly:
The IPU internal bus support only the following data formatting
(44.1.1.3 Data Flows and Formats):
1 YUV 4:4:4 or RGB-8 bits per color component
2 YUV 4:4:4 or RGB-10 bits per color component
3 Generic data (from sensor to the system memory only)
And format conversions are done:
- from memory: unpacking from other formats to IPU supported ones
- to memory: packing in the inverse order.
So, assigning a packing/unpacking strategy to the IPU for those formats
will produce a packing to memory and not the inverse.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'pix->width' field may be updated in mx3_camera_set_fmt() to
fulfill the IPU stride line alignment requirements. If this update
takes place, the 'fmt.pix.sizeimage' field in the struct v4l2_format
stucture returned by VIDIOC_S_FMT is wrong. We need to update the
'pix->sizeimage' field in the mx3_camera_set_fmt() function to fix
this issue.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Even though clk_put() is a no-op on most architectures it is not for
some ARM implementations. To not fail on those, release the clock timer
before freeing the surrounding structure.
This bug was spotted by the semantic patch tool coccinelle using the
script found at scripts/coccinelle/free/kfree.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a function to calculate the number of samples on the media-bus,
required to retrieve one pixel of a certain format.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some camera systems have strong requirement for capturing
an exact number of frames after starting the stream and do
not tolerate losing captured frames. By starting the stream
after the videobuf has queued the buffers, we ensure that
no frame will be lost.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reported by, and based on a patch from, Martin Dauskardt.
The AUDIO_AC3_BITRATE control is still missing from this list, but such
optional controls are a bit hard to handle. This will be fixed automatically
when we switch to the control framework.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/ieee1394/ has been removed in Linux 2.6.37. The corresponding
backend code in firedtv is no longer built in now and can be deleted.
Firedtv continues to work with drivers/firewire/.
Also, fix a Kconfig menu comment: Removal of CONFIG_IEEE1394 made the
"Supported FireWire (IEEE 1394) Adapters" comment disappear; bring it back
with corrected dependency.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some ioctl's were defined wrong on 2.6.2 and 2.6.6, using the wrong
type of R/W arguments. They were fixed, but the old ioctl names are
still there, maintained to avoid breaking binary compatibility:
There's no sense on preserving those forever, as it is very doubtful
that someone would try to use a such old binary with a modern kernel.
Removing them will allow us to remove some magic done at the V4L ioctl
handler.
Note that any application compiled with a videodev2.h from 2.6.7 or later
will be using the correct ioctls.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Having a framerate divisor of 3 is not really necesarry and leads to
various troubles (frames going missing, compression issues) when allowed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a complete rewrite of the old v4l1 vicam subdriver, featuring
multiple resolutions, gain + exposure control and still has less code.
Oh and it is a v4l2 driver rather then v4l1 ofcourse :)
Many thanks to Devin Heitmueller <dheitmueller@kernellabs.com> for
donating his 3com homeconnect to me, which made this rewrite possible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In good lighting conditions (lots of details visible) the current buffers
are sometimes too small.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes the led not working on this camera
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with a camera with usb-id: 0c45:62bb
Also enable dmi based flopped laptop detection for the 0c45:627b ov7660 model.
Some of the MSI laptops with upside down camera have this one instead of the
0c45:624f.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with a camera with usb-id: 0c45:62bb
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
During image capture, the filling rate of the isoc packets is computed.
It is then used by a work queue to update the current JPEG quality.
Tested-by: Franck Bourdonnec <fbourdonnec@chez.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A marker 'ff ff 00 c4 c4 96' indicates an end of frame.
It is 62 bytes long and may be splitted on 2 packets.
It contains a flag 'USB full' which indicates that the frame is truncated.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2-ctl and qv4l2 enumerate controls using V4L2_CTRL_FLAG_NEXT_CTRL,
falling back to the old method if the flag isn't supported.
The v4l2_subdev_queryctrl function will currently handle that flag, but
for the controls of the subdev only. This isn't right, it should refuse
this flag, otherwise v4l2-ctl will only see the controls of the first
subdev.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Subdev controls return codes are evil, as they return -EINVAL to mean
both unsupported and invalid arguments. Due to that, we need to use a
trick to identify what controls are supported by a subdev.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On some cases, driver returns 1. This should be OK, but qv4l2 is too
strict about return values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Having the device detection happening at reset is bad, as every time,
it will produce a message like:
tvp5150 2-005c: tvp5150am1 detected.
This only polutes the log and for an accidental kernel hacker, it looks
like a real problem. So, move those printk's to happen during device
probe.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It makes no sense that tuner_lookup would touch at the standby
state. Remove it.
Thanks-to: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Group a few functions together and add/fix comments for each
block of the driver.
This is just a cleanup patch meant to improve driver readability.
No functional changes in this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is complex, and used by everyone. Better to have it
properly documented.
No functional changes are done in this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tuner-core has no business to do with digital TV. So, don't use
T_DIGITAL_TV on it, as it has no code to distinguish between
them, and nobody fills T_DIGITAL_TV right.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tda9887 used to use the T_STANDBY type internally, while tea5761
used it to put the device to sleep. Fix the code for it to work
properly with the tuner core changes and remove this flag from
tuner.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the now obsolete set_freq. Also merge set_addr and set_type_addr.
In the past, it used to have two different setup calls, one to set just
the tuner type to any tuner found, and another to set the type only if
the address matches. Those two internal calls were grouped together,
but the functions weren't merged, making the code uglier.
No functional changes are done in this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A static var is evil, especially if a device has two boards with
xc5000. Instead, just like the other drivers, use stack to store
its config during setup.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Power down tuners at suspend. At resume, if the tuner is in standby,
calls set_mode, that will turn it on and set the latest frequencies.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the past, T_STANDBY were used on devices with a separate radio tuner to
mark a tuner that were disabled. With the time, it got newer meanings.
Also, due to a bug at the logic, the driver might incorrectly return
T_STANDBY to userspace.
So, instead of keeping the abuse, just use a boolean for storing
such information.
We can't remove T_STANDBY yet, as this is used on two other drivers. A
latter patch will address its usage outside tuner-core.
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Properly document those functions and do some cleanups around that.
There's just one behavior change on this patchset: it will now restore
TV frequency when changing from radio to TV mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a big patch with no functional changes. It just
rearranges everything inside the driver, and prepares to
break TV and Radio into two separate fops groups.
Currently, it has an heuristics logic to determine if the
call came from radio or video. However, the caller driver
knows for sure, so tuner-core shouldn't try to guess it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After registering the cdev, it would be possible do have an open on it.
In a matter of fact, some versions of udev do this. So, move registration
to the end and protect it with a mutex.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds support for Pixelviex Xcapture USB grabber device.
This device has one composite and one s-video entry
only, plus a button.
For now, the button is not supported.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some devices don't need to use it. So allow to just disable this logic.
Having it enabled on some devices cause power management to complain,
generating error -71.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of per-model tests all over the code, use some parameters
at the board entries to describe the model variants for:
- devices with 417 MPEG encoder;
- devices that use external AV;
- devices where vbi VANC endpoint doesn't work;
- devices with xc5000 that require different IF
initialization (and probably will cover also
xc3028).
- devices with xceive tuner that require a reset
during init.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The check for xc5000 assumes that the tuner will always
be using the same bus and will have the same address.
As those are configurable via dev->board, it should use,
instead, the values defined there.
Also, a similar type of test will be needed by other
tuners (for example, for TUNER_XC2028)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just a cleanup patch. Removes one indent level by moving
the return -ENODEV to happen before the device register
logic, if the interface is not the audio/video (int 1).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My Hauppauge WinTV HVR-1400 needs sometimes more then only one retry to load the firmware successfully.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
KERNEL_VERSION: 2.6.37
common.c in function ssize_t si470x_fops_read.
1. First mutex_lock on &radio->lock in line 441
2. Second in line 462
I think that mutex in line 462 is not needed.
433static ssize_t si470x_fops_read(struct file *file, char __user *buf,
434 size_t count, loff_t *ppos)
435{
....
441 mutex_lock(&radio->lock);
442 if ((radio->registers[SYSCONFIG1] & SYSCONFIG1_RDS) == 0)
443 si470x_rds_on(radio);
444
445 /* block if no new data available */
446 while (radio->wr_index == radio->rd_index) {
447 if (file->f_flags & O_NONBLOCK) {
448 retval = -EWOULDBLOCK;
449 goto done;
450 }
451 if (wait_event_interruptible(radio->read_queue,
452 radio->wr_index != radio->rd_index) < 0) {
453 retval = -EINTR;
454 goto done;
455 }
456 }
457
458 /* calculate block count from byte count */
459 count /= 3;
460
461 /* copy RDS block out of internal buffer and to user buffer */
462 mutex_lock(&radio->lock);
Found by Linux Device Drivers Verification Project
Remove second mutex.
Signed-off-by: Alexander Strakh <strakh@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Unable to test this due to lack of hardware.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/vivi.c:1059: warning: this decimal constant is unsigned only in ISO C90
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
