Comment out the code that is never reached in qla83xx_idc_unlock()
and also in qlt_set_data_offset() to avoid that static source code
analysis tools report warnings for this code.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Fix compilation errors on forgotten #include <linux/dmapool.h> and warnings when
CONFIG_PCI is not set.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This fixes a regression caused by commit
d3557fc8be megaraid_sas : Add separate function
for setting up IRQs This makes boot end with 'root does not exist' message on
certain adapters.
The bug is that the driver does not setup ints for cards without msi-x
support. This patch fixes it, in addition to that it moves tasklet
initialisation before enable_intr, otherwise a kernel panic may occur, when an
interrupt arrives before the tasklet is ready.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The domain controller PLOGI's concurrent with prior LOGO's/unreg_rpi's
completing created a race condition where driver rpi ref count can
inadvertantly hit 0 and the rpi attempted to be freed. This error
sometimes resulted in Warning messages indicating kref.h via
lfpc_nlp_get+0x128.
Correct by dropping any new PLOGI until the prior nport state has settled.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
TMF's were getting error messages on FCP_RSP errors (underrun). Underruns
aren't meaningful in the scenario. Change the error message to filter out
these response check errors, and don't unconditionally mark the cmd as
in error.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The driver inadvertainly constrained the id space to 8 bits, when its
a full 16 bits from hw. This resulted in bad id's being written to the
hardware. Resulted in symptoms such as incomplete initialization, no
detection of link events, etc.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Didn't check for less-than-or-equal zero. Means we may later call
scsi_dma_unmap() even though we don't have valid mappings.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
With blk-mq support in the mid-layer, lpfc can do IO steering based
on the information in the request tag. This patch allows lpfc to use
blk-mq if enabled. If not enabled, we fall back into the emulex-internal
affinity mappings.
This feature can be turned on via CONFIG_SCSI_MQ_DEFAULT or passing
scsi_mod.use_blk_mq=Y as a parameter to the kernel.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
When a remote nport changes it's DID, a new ndlp is used.
However, we left the old ndlp state unchanged and still in
a discovery state. The may stall discovery resulting in some
devices not being discovered. Correct by swapping the state
of the 2 ndlp's when a DID swap is detected.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
If a vport was deleted while in the middle of discovery, we weren't
clearing the nport discovery flag. Correct by clearing the flag and
cancelling our discovery timeout timer.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
LCB requests to set Beacon would fail if the beacon was already enabled
internally as the mailbox command used to query the state failes with
an already-set status.
Correct by enhancing the check so we don't fail if if the already set
status comes back.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Correct locking and refcounting in tracking our rports
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
We inadvertantly took the path to recreate the vport while in a
driver teardown path
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Also has a little whitespace fixing.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Fix incorrect reference counting
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The order (it's a shall, but hard to dictate after the fact) is given in
FC-SCM - kind of. SCM indicates what shall be implemented, lists it as (a),
(b), (c), but actually doesn't say it has to be in that order. The only hard
requirement, called out in FCP-4, is that you must register your FC-4 Type
(via RFT_ID) before registering FC-4 Type Features (via RFF_ID), which makes
sense. We obviously violated this and there were some switches (or newer fw in
them) that enforced it. The other rule of thumbs are: register your data with
the switch first, then register for SCRs, then do queries about the fabric,
with the SCRs telling you of changes post the queries.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Nothing in <asm/io.h> uses anything from <linux/vmalloc.h>, so
remove it from there and fix up the resulting build problems
triggered on x86 {64|32}-bit {def|allmod|allno}configs.
The breakages were triggering in places where x86 builds relied
on vmalloc() facilities but did not include <linux/vmalloc.h>
explicitly and relied on the implicit inclusion via <asm/io.h>.
Also add:
- <linux/init.h> to <linux/io.h>
- <asm/pgtable_types> to <asm/io.h>
... which were two other implicit header file dependencies.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[ Tidied up the changelog. ]
Acked-by: David Miller <davem@davemloft.net>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Colin Cross <ccross@android.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: James E.J. Bottomley <JBottomley@odin.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Suma Ramars <sramars@cisco.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When creating a new endpoint, we look for a free id
for the new endpoint. We baisically loop on possible ids
and use the first id that class_find_device() returns NULL.
However, we are missing a reference put when class_find_device()
does find an existing device for a given id.
Reported-by: Alex Lyakas <alex@zadarastorage.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
non-x86 builds want the #warning in the IPS code about compiling on the wrong
architecture removed because it keeps triggering on their platforms build
farms. Transform from a compile time warning into a runtime one with taint to
preserve the original intent of the authors.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The driver waits for command completion event while cleanup of task
within the frwd lock and back locks. The frwd lock was still held
which caused the call trace while issuing a device reset.
Release the frwd lock along with the back lock
to avoid waiting in the lock context.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Fix the firmware assert, during target logout in
case driver received FIN from target before waiting for
asyncronous response.
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Newer revisions of QUALCOMM Technologies UFS host controller may not
advertise the correct version information in UFS HCI VER register.
To handle this, enable UFSHCD_QUIRK_BROKEN_UFS_HCI_VERSION to let
UFS standard host controller driver call into vendor specific
operation to get right UFS HCI VER register value.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Some host controller hardware controllers may not advertise correct
version in UFS HCI VER register. To workaround this, add new quirk
and call the host controller hardware vendor specific callback to
get the correct UFS HCI version register value.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Current version of host controller on QUALCOMM Technologies requires
this quirk to be enabled, as DME commands to device must be sent
only in AUTO mode (SLOW AUTO or FAST AUTO).
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Some UFS host controllers may only allow accessing the peer DME attribute
in AUTO mode (FAST AUTO or SLOW AUTO) hence we had added a quirk for
switching to AUTO power mode before accessing the peer DME attribute.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
With the G3 UFS devices, changing gear into HS is failing in UFS host
controllers of version 0x2.
The quirk solves the problem of changing gear into HS by enabling
the attribute that specifies whether or not the inbound Link supports
unterminated line in HS mode.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The attribute PA_RXHSUNTERMCAP specifies whether or not the
inbound Link supports unterminated line in HS mode. enabling this
attribute to 1 fixes moving to HS gear.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
LCC (Line Control Command) are being used for communication between
UFS host and UFS device. But UFS host controller on QUALCOMM
Technologies have an issue with issuing the LCC commands to
UFS device and hence this quirk is enabled in order to to disable
LCC from the host side.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
LCC (Line Control Command) are being used for communication between
UFS host and UFS device.
New commercial UFS devices don't have the issues with LCC processing
but UFS host controller might still have the issue with LCC processing,
hence, added a routine to disable TX LCC on the device.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Current versions of UFS host controllers on QUALCOMM Technologies
have interrupt aggregation logic broken.
Interrupt aggregation may not work if both threshold count and timeout
is enabled. Hence disable interrupt aggregation by enabling
UFSHCD_QUIRK_BROKEN_INTR_AGGR quirk until its fixed in the newer
UFS host controller revisions.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
UFS HCI (Host Controller Interface) allows the transfer requests
interrupts to be aggregated to generate the single interrupt but
this can impact the performance. Hence introduce the capability which
gives choice to use the interrupt aggregation capability or not.
By default interrupt aggregation capability is kept disabled.
This change also introduces a quirk for broken interrupt aggregation
feature, as in some UFS controllers, this feature may not work.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Increase the default init stage change timeout from 15 seconds to 30 seconds.
This resolves issues we have seen with some adapters not transitioning
to the first init stage within 15 seconds, which results in adapter
initialization failures.
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch implements tape statistics in the st module via
sysfs. Current no statistics are available for tape I/O and there
is no easy way to reuse the block layer statistics for tape
as tape is a character device and does not have perform I/O in
sector sized chunks (the size of the data written to tape
can change). For tapes we also need extra stats related to
things like tape movement (via other I/O).
There have been multiple end users requesting statistics
including AT&T (and some HP customers who have not given
permission to be named). It is impossible for them
to investigate any issues related to tape performance
in a non-invasive way.
[jejb: eliminate PRId64]
Signed-off-by: Shane Seymour <shane.seymour@hp.com>
Tested-by: Shane Seymour <shane.seymour@hp.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the functions that are used by both the initiator and target
subsystems into scsi_common.c/.h. This change will allow to remove
the initiator SCSI header include directives from most SCSI target
source files in a later patch.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch is rebased on top of recently sent 18 patches(submitted by me) for
megaraid_sas driver.
Change the return value of wait_and_poll() and megsas_issue_blocked_cmd()
based on MFI_STAT returned by firmware for that command. Earlier driver always
send return type based on command completion (but never check MFI_STAT_OK for
that command), so even if command is failed by firmware still driver will
return SUCCESS status from these functions wait_and_poll() and
megsas_issue_blocked_cmd() and if caller of these functions does not check
command status (MFI_STAT), then it may endup using invalid data returned in
DMA buffers(one of the example is megasas_ld_list_query DCMD). Best thing to
avoid this type of issue is do error handling and set proper return type from
caller function wait_and_poll() and megsas_issue_blocked_cmd().
The change proposed in this patch will fix the regression introduced in patch-
"90dc9d9 megaraid_sas : MFI MPT linked list corruption fix" inside function
megasas_ld_list_query(). Prior to this MFI MPT linked list corruption fix
patch, megasas_ld_list_query() function used to check DCMD status(returned by
firmware) but with this linked list corruption fix patch, DCMD status will not
be checked inside function megasas_ld_list_query() and introduced this issue
of wrong data being used by function megasas_ld_list_query().
Cc: <stable@vger.kernel.org>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
'0' is now used as the default cmd_per_lun value,
so there's no need to explicitly set it to '1' in the
host template.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
update driver version
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
add in support for latest PMC controller
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Synchronize completion the reset with completion of outstanding commands
Extending the newly-added synchronous abort functionality,
now also synchronize resets with the completion of outstanding commands.
Rename the wait queue to reflect the fact that it's being used for both
types of waits. Also, don't complete commands which are terminated
due to a reset operation.
fix for controller lockup during reset
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
If hpsa_wait_for_board_state fails, hpsa_kdump_soft_reset
should propagate its return value (e.g., -ENODEV) rather
than just returning -1.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Rather than numbering the hpsa controllers with an
incrementing 0..n value (e.g., that shows up in
/proc/interrupts), use the scsi midlayer
host_no (e.g. matching /sys/class/scsi_host/hostNN).
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Rework slave allocation:
- separate the tagging support setup from the hostdata setup
- make the hostdata setup act consistently when the lookup fails
- make the hostdata setup act consistently when the device is not added
- set up the queue depth consistently across these scenarios
- if the block layer mq support is not available, explicitly enable and
activate the SCSI layer tcq support (and do this at allocation-time so
that the tags will be available for INQUIRY commands)
Tweak slave configuration so that devices which are masked are also
not attached.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Add the interrupt number to the interrupt names that
appear in /proc/interrupts, so they are unique
Also, delete the IRQ and DAC prints. Other parts of the kernel
already print the IRQ assignments, and dual-address-cycle support
has not been interesting since the parallel PCI bus went from
32 to 64 bits wide.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Don't create the resubmit workqueue in hpsa_init_one until everything else
is ready to use, so everything can be freed in reverse order of when they
were allocated without risking freeing things while workqueue items are
still active.
Destroy the workqueue in the right order in
hpsa_undo_allocations_after_kdump_soft_reset too.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
If registering the special interrupt handlers in hpsa_init_one
before a soft reset fails, the error exit needs to deallocate
everything that was allocated before.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
In hpsa_undo_allocations_after_kdump_soft_reset,
the things allocated in hpsa_init_one step 2 -
h->resubmit_wq and h->lockup_detected need to
be freed, in the right order.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
If try_soft_reset fails to re-allocate irqs, the error exit
starts with free_irq calls, which generate kernel WARN
messages since they were already freed a few lines earlier.
Jump to the next exit label to skip the free_irq calls.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Despite the fact that PCI devices are enabled in this order:
1. pci_enable_device
2. pci_request_regions
Documentation/PCI/pci.txt specifies that they be undone
in this order
1. pci_disable_device
2. pci_release_regions
Tested by injecting error in the call to pci_enable_device
in hpsa_init_one -> hpsa_pci_init:
[ 9.095001] hpsa 0000:04:00.0: failed to enable PCI device
[ 9.095005] hpsa: probe of 0000:04:00.0 failed with error -22
(-22 is -EINVAL)
and then in the call pci_request_regions:
[ 9.178623] hpsa 0000:04:00.0: failed to obtain PCI resources
[ 9.178671] hpsa: probe of 0000:04:00.0 failed with error -16
(-16 is -EBUSY)
and then by adding
reset_devices
to the kernel command line and inject errors into the two
calls to pci_enable_device and the call to pci_request_regions
in hpsa_init_one -> hpsa_init_reset_devices.
(inject on 6th call, 1st to hpsa2)
[ 62.413750] hpsa 0000:04:00.0: Failed to enable PCI device
(inject on 7th call, 2nd to hpsa2)
[ 62.807571] hpsa 0000:04:00.0: failed to enable device.
(inject on 8th call, 3rd to hpsa2)
[ 62.697198] hpsa 0000:04:00.0: failed to obtain PCI resources
[ 62.697234] hpsa: probe of 0000:04:00.0 failed with error -16
The reset_devices path calls return -ENODEV on failure
rather than passing the result, which apparently doesn't
cause the pci driver to print anything.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Divide the loop in hpsa_scatter_gather() into two, one for the initial SG list
and a second one for the chained list, if any. This allows the conditional
check which resets the indicies for the chained list to be performed outside
the loop instead of being done on every iteration inside the loop.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Factor out the code which sends the TEST_UNIT_READY from
wait_for_device_to_become_ready() into its own function.
Move the code which waits for the TEST_UNIT_READY from
wait_for_device_to_become_ready() into its own function.
If a logical drive has failed, resetting it will ensure
outstanding commands are completed, but polling it with
TURs after the reset will not work because the TURs will
never report good status. So successful TUR should not
be a condition of success for the device reset error
handler.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Don't return from the abort request until the target command is complete.
Mark outstanding commands which have a pending abort, and do not send them
to the host if we can avoid it.
If the current command has been aborted, do not call the SCSI command
completion routine from the I/O path: when the abort returns successfully,
the SCSI mid-layer will handle the completion implicitly.
The following race was possible in theory.
1. LLD is requested to abort a scsi command
2. scsi command completes
3. The struct CommandList associated with 2 is made available.
4. new io request to LLD to another LUN re-uses struct CommandList
5. abort handler follows scsi_cmnd->host_scribble and
finds struct CommandList and tries to aborts it.
Now we have aborted the wrong command.
Fix by resetting the scsi_cmd field of struct CommandList
upon completion and making the abort handler check that
the scsi_cmd pointer in the CommadList struct matches the
scsi_cmnd that it has been asked to abort.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
cleanup command completions
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
add support for tmf when in ioaccel2 mode
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Joe Handzik <joseph.t.handzik@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The SCSI midlayer already prints more detail about completions,
and has logging level options to filter them if not wanted.
These just slow down the system if a lot of errors occur,
stressing error handling even more.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
report more useful information on aborts
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Improve initialization error handling in hpsa_init_one
Clean up style and indent issues
Rename functions for consistency
Improve error messaging on allocations
Fix return status from hpsa_put_ctlr_into_performant_mode
Correct free order in hpsa_init_one using new function
hpsa_free_performant_mode
Prevent inadvertent use of null pointers by nulling out the parent structures
and zeroing out associated size variables.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
correct return codes for error conditions
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
cmd_alloc can no longer return NULL, so don't check for NULL any more
(which is unreachable code).
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
improve ioaccel2 error handling, including better handling of
underrun statuses
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Signed-off-by: Joe Handzik <joseph.t.handzik@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Increase the request size for ioaccel2 path.
The error, if any, returned by hpsa_allocate_ioaccel2_sg_chain_blocks
to hpsa_alloc_ioaccel2_cmd_and_bft should be returned upstream rather
than assumed to be -ENOMEM.
This differs slightly from hpsa_alloc_ioaccel1_cmd_and_bft,
which does not call another hpsa_allocate function and only
has -ENOMEM to return from some kmalloc calls.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
refactor freeing of resources into more logical functions
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Pull SCSI target fixes from Nicholas Bellinger:
"These are mostly minor fixes, with the exception of the following that
address fall-out from recent v4.1-rc1 changes:
- regression fix related to the big fabric API registration changes
and configfs_depend_item() usage, that required cherry-picking one
of HCH's patches from for-next to address the issue for v4.1 code.
- remaining TCM-USER -v2 related changes to enforce full CDB
passthrough from Andy + Ilias.
Also included is a target_core_pscsi driver fix from Andy that
addresses a long standing issue with a Scsi_Host reference being
leaked on PSCSI device shutdown"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iser-target: Fix error path in isert_create_pi_ctx()
target: Use a PASSTHROUGH flag instead of transport_types
target: Move passthrough CDB parsing into a common function
target/user: Only support full command pass-through
target/user: Update example code for new ABI requirements
target/pscsi: Don't leak scsi_host if hba is VIRTUAL_HOST
target: Fix se_tpg_tfo->tf_subsys regression + remove tf_subsystem
target: Drop signal_pending checks after interruptible lock acquire
target: Add missing parentheses
target: Fix bidi command handling
target/user: Disallow full passthrough (pass_level=0)
ISCSI: fix minor memory leak
refactor error cleanup and shutdown
disable interrupts and pci_disable_device on critical failures
add hpsa_free_cfgtables function
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
replace calls to hpsa_free_irqs_and_disable_msix with
hpsa_free_irqs and hpsa_disable_interrupt_mode
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
get drive queue depth to help avoid task set full conditions.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Joe Handzik <joseph.t.handzik@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
use ioaccel2 path to submit I/O to physical drives in HBA mode
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Joe Handzik <joseph.t.handzik@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
offload_enabled changes are deferred until after the
added/updated prints occur, so the values are incorrect.
defer printing SSD Smart Path Enabled status information until the
information is correct
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
clean up command submission
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
allow the controller firmware to queue up commands when the ioaccel device
queue is full.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
add error handling for failure when registering with SCSI subsystem.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Factor out hpsa_cmd_init from cmd_alloc(). We also need
this for resubmitting commands down the default RAID path
when they have returned from the ioaccel paths with errors.
In particular, reinitialize the cmd_type and busaddr fields as these
will not be correct for submitting down the RAID stack path
after ioaccel command completion.
This saves time when submitting commands.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
make function names more consistent and meaningful
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
expose a detected lockup via sysfs
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
In hba mode, we could get sense data in descriptor format so
we need to handle that.
It's possible for CommandStatus to have value 0x0D
"TMF Function Status", which we should handle. We will get
this from a P1224 when aborting a non-existent tag, for
example. The "ScsiStatus" field of the errinfo field
will contain the TMF function status value.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
make tracking of outstanding commands more robust
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Do not send aborts to logical devices that do not support aborts
Instead of relying on what the Smart Array claims for supporting logical
drives, simply try an abort and see how it responds at device discovery
time. This way devices that do support aborts (e.g. MSA2000) can work
and we do not waste time trying to send aborts to logical drives that do
not support them (important for high IOPS devices.)
While rescanning devices only test whether devices support aborts
the first time we encounter a device rather than every time.
Some Smart Arrays required aborts to be sent with tags in
the wrong endian byte order. To avoid having to know about
this, we would send two aborts with tags with each endian order.
On high IOPS devices, this turns out to be not such a hot idea.
So we now have a list of the devices that got the tag backwards,
and we only send it one way.
If all available commands are outstanding and the abort handler
is invoked, the abort handler may not be able to allocate a command
and may busy-wait excessivly. Reserve a small number of commands
for the abort handler and limit the number of concurrent abort
requests to the number of reserved commands.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Allow driver initiated commands to have a timeout. It does not
yet try to do anything with timeouts on such commands.
We are sending a reset in order to get rid of a command we want to abort.
If we make it return on the same reply queue as the command we want to abort,
the completion of the aborted command will not race with the completion of
the reset command.
Rename hpsa_scsi_do_simple_cmd_core() to hpsa_scsi_do_simple_cmd(), since
this function is the interface for issuing commands to the controller and
not the "core" of that implementation. Add a parameter to it which allows
the caller to specify the reply queue to be used. Modify existing callers
to specify the default reply queue.
Rename __hpsa_scsi_do_simple_cmd_core() to hpsa_scsi_do_simple_cmd_core(),
since this routine is the "core" implementation of the "do simple command"
function and there is no longer any other function with a similar name.
Modify the existing callers of this routine (other than
hpsa_scsi_do_simple_cmd()) to instead call hpsa_scsi_do_simple_cmd(), since
it will now accept the reply_queue paramenter, and it provides a controller
lock-up check. (Also, tweak two related message strings to make them
distinct from each other.)
Submitting a command to a locked up controller always results in a timeout,
so check for controller lock-up before submitting.
This is to enable fixing a race between command completions and
abort completions on different reply queues in a subsequent patch.
We want to be able to specify which reply queue an abort completion
should occur on so that it cannot race the completion of the command
it is trying to abort.
The following race was possible in theory:
1. Abort command is sent to hardware.
2. Command to be aborted simultaneously completes on another
reply queue.
3. Hardware receives abort command, decides command has already
completed and indicates this to the driver via another different
reply queue.
4. driver processes abort completion finds that the hardware does not know
about the command, concludes that therefore the command cannot complete,
returns SUCCESS indicating to the mid-layer that the scsi_cmnd may be
re-used.
5. Command from step 2 is processed and completed back to scsi mid
layer (after we already promised that would never happen.)
Fix by forcing aborts to complete on the same reply queue as the command
they are aborting.
Piggybacking device rescanning functionality onto the lockup
detection thread is not a good idea because if the controller
locks up during device rescanning, then the thread could get
stuck, then the lockup isn't detected. Use separate work
queues for device rescanning and lockup detection.
Detect controller lockup in abort handler.
After a lockup is detected, return DO_NO_CONNECT which results in immediate
termination of commands rather than DID_ERR which results in retries.
Modify detect_controller_lockup() to return the result, to remove the need for
a separate check.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Signed-off-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
We had a mix of formats used for specifying controller, bus, target,
and lun address of devices.
change to the format used by the scsi midlayer and upper layer (2:3:0:0)
so you can easily follow the information from hpsa to scsi midlayer
to sd upper layer.
Also add this information:
- product ID
- vendor ID
- RAID level
- SSD Smath Path capable and enabled
- exposure level (sg-only)
Example:
hpsa 0000:04:00.0: added scsi 2:0:0:0: Direct-Access HP LOGICAL VOLUME RAID-0 SSDSmartPathCap+ En+ Exp=4
scsi 2:0:0:0: Direct-Access HP LOGICAL VOLUME 10.0 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdr] 12501713072 512-byte logical blocks: (6.40 TB/5.82 TiB)
sd 2:0:0:0: [sdr] 4096-byte physical blocks
sd 2:0:0:0: [sdr] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg20 type 0
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Cache the ioaccel handle so that when we need to abort commands sent
down the ioaccel2 path, we can look up the LUN ID in h->dev[] instead of
having to do I/O to the controller.
Add a field to elements in h->dev[] to keep track of how the device is exposed
to the SCSI mid layer: Not at all, without an upper level driver
(no_uld_attach) or normally exposed.
Since masked physical devices are now present in h->dev[] array
it would be perfectly possible to do
echo scsi add-single-device 2 2 0 0 > /proc/scsi/scsi
and bring them online. This was previously not allowed for masked
physical devices.
Ensure that the mapping of physical disks to logical drives gets updated in a
consistent way when a RAID migration occurs and is not touched until updates
to it are complete.
now instead of doing CISS_REPORT_PHYSICAL to get the LUNID for
the physical disk in hpsa_get_pdisk_of_ioaccel2(), just get
it out of h->dev[] where we already have it cached.
do not touch phys_disk[] for ioaccel enabled logical drives during rescan
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The hpsa driver touches the hardware before checking the pci-id table.
This way, especially in kdump, it may confuse the proper driver (cciss).
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Don Brace <Don.Brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The only instance of ->put_session is in qla2xxx, and was added by commit
aaf68b ("tcm_qla2xxx: Convert to TFO->put_session() usage") with the following
description:
This patch converts tcm_qla2xxx code to use an internal kref_put() for
se_session->sess_kref in order to ensure that qla_hw_data->hardware_lock
can be held while calling qlt_unreg_sess() for the final put.
But these day we're already holding the hardware lock over qlt_unreg_sess in
the ->close_session callback, so we're fine without this method.
(Re-add missing tcm_qla2xxx_release_session + drop put_session usage - nab)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simplify target core and target drivers by storing the task tag
a.k.a. command identifier inside struct se_cmd.
For several transports (e.g. SRP) tags are 64 bits wide.
Hence add support for 64-bit tags.
(Fix core_tmr_abort_task conversion spec warnings - nab)
(Fix up usb-gadget to use 16-bit tags - HCH + bart)
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that struct se_portal_group contains a protocol identifier field we can
take all the code to format an parse protocol identifiers in CDBs into common
code instead of leaving this to low-level drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that we store the protocol identifier in the tpg structure we don't
need this method.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove the unneeded fabric_ptr argument, and change the type argument
to pass in a SPC protocol identifier.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
