It fixes a couple of minor bugs, comments out a bogus BUG_ON, sets fh->type
correctly, uses dev->width and dev->height for now, and adds a missing spinlock
init (nasty - caused a system lockup). It also adds some debug code which
probably isn't all that useful. I haven't tested this version of the patch yet,
though, so I'm not sure what you can expect if you try it.
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The usage of videobuf-vmalloc allows to cleanup em28xx logic.
Also, it reduced its size by about 5.42% on i386 arch (and about 7.5% on x86_64):
39113 4876 40 44029 abfd old/em28xx.ko
36731 4868 40 41639 a2a7 /home/v4l/master/v4l/em28xx.ko
Also, the preliminary tests, made on a single core 1.5 MHz Centrino showed
that CPU usage reduced from 42%-75% to 28%-33% (reports from "top") command.
A test with time command presented an even better result:
This is the performance tests I did, running code_example to get 1,000 frames
@29.995 Hz (about 35 seconds of stream), tested on a i386 machine, running at
1,5GHz:
The old driver:
$ time -f "%E: %Us User time, %Ss Kernel time, %P CPU used" ./capture_example
0:34.21: 8.22s User time, 25.16s Kernel time, 97% CPU used
The videobuf-based driver:
$ time -f "%E: %Us User time, %Ss Kernel time, %P CPU used" ./capture_example
0:35.36: 0.01s User time, 0.05s Kernel time, 0% CPU used
Conclusion:
The time consumption to receive the stream where reduced from about 33.38
seconds to 0.05 seconds.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Static memory is always initialized with 0.
- Replaced in some cases C99 comments for /* */
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx driver is capable of handling more than one usb device. However, isoc
transfers require a large amount of data to be transfered.
Before this patch, just one em28xx board were enough to allocate more than 50%
URBs:
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 8
B: Alloc=480/800 us (60%), #Int= 0, #Iso= 2
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
So, only one board could use an USB host at the same time. After the patch, it
is possible to use more than one em28xx at the same time, on the same usb host,
if the image size is slower or equal to 345600, since those images will
require about 30% of the URBs:
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 8
B: Alloc=232/800 us (29%), #Int= 0, #Iso= 2
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
So, in thesis, after the patch, it would be possible to use up to 3 boards by
each usb host, if the devices are generating small images.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Improves audio configurations on em28xx:
- mutes audio before changing amux;
- adds a delay after setting audio src;
- waits up to 50ms for ac97 busy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the following needlessly global functions static:
- em28xx-core.c:em28xx_write_reg_bits()
- em28xx-video.c:em28xx_vdev_init()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
has_tuner flag doesn't make much sense, since tuner_type=TUNER_ABSENT
means the same thing.
Having two ways to say that a tuner is not present is
not nice, since it may lead to bad setups. In fact, with the previous
code, if a device were using has_tuner=0, but the user forces a tuner,
with modprobe option tuner=type, the modprobe option won't work.
Also, tveeprom returns TUNER_ABSENT, when tuner is unknown or absent.
So, with the previous logic, in this case, the driver should set
has_tuner=0, or has_tuner=1 otherwise.
Instead of adding several additional tests and setups, better just to
remove .has_tuner.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Before this patch, only Vendor Class audio support were loaded. This means that
older em28xx devices won't have digital audio support loaded.
This patch changes the logic to auto load eighter snd-usb-audio, for devices
with USB Audio Class or em28xx-alsa, for devices with USB Vendor Class.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Older em28xx devices does implement standard Audio Class.
However, on newer devices, this were replaced by a Vendor Class. This
patch autodetects that an em28xx lacks Audio Class and auto-loads
em28xx-alsa, for the devices that implements only a Vendor Class.
For devices with Audio Class, snd-usb-audio module will provide an ALSA
interface.
This patch uses the request_module_async function as defined on cx88-mpeg.c,
originally wrote by Markus Rechberger.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It is possible to select audio inputs via em28xx or via ac97 functions.
This patch allows configuring a board to use either one way.
It also do some cleanups at audio setup configurations.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With the conversion to the vidio_ioctl2, tvnorms array is not required anymore.
Also, removed some code from V4L1 time (VIDEO_MODE_foo), specied at the
non-used video_decoder.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were some vestiges of an old V4L1 I2C driver that were called by em28xx.
This patch removes this dead code, and replaces videodev.h to videodev2.h
Now, this driver doesn't require V4L1 anymore.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Uses the newer ioctl handler at videodev. This patch also cleans up some
bad logic at the driver and do CodingStyle and other cleanups at the
resulting driver.
Also, since VIDIOCMBUF were not working, the V4L1 compat code were removed.
The compat code will eventually be re-inserted, if we find a clean way for
implementing compatibility with the old API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
On some situations, closing an streaming application and re-opening were
returning -EBUSY.
Uses the same locking schema also present on cx88.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allows shared access support for em28xx. Just one userspace application is
allowed to get stream. The other(s) application(s) can change V4L2 controls,
set video standards, etc.
This patch were splited from Markus Rechberger's tree and backported to 2.6.17
by Pádraig Brady.
The original patch were ported to the latest em28xx version and had CodingStyle
corrected to solve the issues pointed by scripts/checkpatch.pl.
Thanks to Pádraig Brady <P@draigBrady.com> for pointing this.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds autodetection support for the Cinergy200 USB and the VGear PocketTV.
Whenever a usb device with generic empia em2800 usb ids is detected the device
gets scanned for connected i2c devices. If the device list matches an em2800
device in the device list the model id gets changed accordingly.
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The attached patch modifies the em28xx driver so that there can be ioctls from
multiple different threads.
This is necessary for capture apps like MPlayer that use different threads for
capturing and channel tuning.
Now the locking is only done for the ioctls that change properties of the
device or access the i2c bus.
It also removes some locks that look unnecessary:
In em28xx_init_dev:
the videodevice is not registered yet so nothing can access the hardware
meanwhile, the device struct is not assigned to the interface yet so no race
with disconnect is possible
In em28xx_release_resources:
it gets only called when dev->lock is already held
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds a function to allow trying to detect boards that shares
the generic IDs.
The current detection method is based at eeprom checksum.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently, the only tuner-specific device that allows special
configurations is tda9887. However, tea5767 also may require some
special configurations (for example, to specify a different Xtal freq).
This patch replaces TDA9887_SET_CONFIG by a more generic internal ioctl
(TUNER_SET_CONFIG). The newer one allows specifying what tuner is
appliable to a configuration set, and allows an arbitrary configuration
struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The attached patch is required so that the autodetecion code also works after
a reboot.
Setting the I2C speed does not seem to be supported for em2800.
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This em28xx-video.c uses functions from this header, but doesn't include it.
It depends on some v4l headers included two levels down including poll.h,
which includes mm.h.
These v4l headers might change, so it's best to include the headers needed
directly.
It also causes problems for the out of core build system's backward
compatibility with older kernels, which is the real reason I bothered to
create a patch for something that would otherwise be so minor that it would
hardly be worth the trouble.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
struct video_device used to define a .hardware field. While
initialized on severl drivers, this field is never used inside V4L.
However, drivers using it need to include the old V4L1 header.
This seems to cause compilation troubles with some random configs.
Better just to remove it from all drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
The rest of V4L files.
There is one list_for_each+list_entry in cpia_pp.c that
wasn't changed because it expects the loop iterator to remain NULL if
the list is empty.
A bug in vivi is fixed; the 'safe' version needs to be used because the loop
deletes the list entries.
Simplify a second loop in vivi and get rid if an un-used variable in that loop.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some lines later filp->private_data is initialized to dev again.
Since there are some checks that might fail in the mean time
keep the later version.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If, in em28xx_usb_probe() the memory allocation
dev->alt_max_pkt_size = kmalloc(32*
dev->num_alt,GFP_KERNEL);
fails, then we'll bail out and return -ENOMEM.
The problem is that in that case we don't free the storage allocated
to 'dev', thus causing a memory leak.
This patch fixes the leak by freeing 'dev' before we return -ENOMEM.
This fixes Coverity bug #647.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@sdl.org: dvb fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- CAFE_CCIC needs to depend on PCI, else "allyesconfig" breaks
on systems without PCI
- em28xx-video can't udelay(2500) else "allyesconfig" breaks
on systems that refuse to spin that long (I saw it on ARM)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The extra argument makes it possible to reset subsystems of a chip if
that is supported.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We should no longer try to load the tda9887 module, because it no longer
exists. The tda9887 driver has been merged into the tuner module.
This patch removes all instances of request_module("tda9887") from
the following video4linux drivers: bttv, cx88, em28xx and saa7134.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Use new routing input defines in em28xx-cards.c
- Fix S-Video settings for tvp5150-based cards (input was copied from saa7115
based cards and worked only because S-Video was selected in the default: case)
- Replace VIDIOC_S_INPUT by VIDIOC_INT_S_VIDEO_ROUTING in em28xx-video.c
- Remove the now obsolete VIDIOC_S_INPUT handler in saa7115.c
- Add VIDIOC_INT_G/S_VIDEO_ROUTING in tvp5150.c
- Add new media/tvp5150.h with the routing defines.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In several places we use dev->devno right after we kfree() dev. This fixes
coverity bug id #1065
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Renamed various msp3400 routing defines to be more consistent and less
confusing. Esp. the MSP_DSP_OUT defines were confusing since it is really
a DSP input.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Remove old DECODER_ commands from tvp5150.c, replacing them with newer
ones if appropriate.
- Small VIDIOC_G_TUNER fixes in msp3400 and tuner.
- Fix VIDIOC_S_TUNER support in em28xx.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- implement VIDIOC_INT_S_AUDIO_ROUTING for msp3400 and tvaudio
- use the new command in bttv, pvrusb2 and em28xx.
- remove the now obsolete MSP_SET_MATRIX from msp3400 (yeah!)
- remove the obsolete VIDIOC_S_AUDIO from msp3400.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now, em28xx uses saa7115 instead of saa711x.
saa7115 driver is capable of handling saa 7113, 7114 and 7115.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
