Here's a new device ID for the ftdio_sio driver.
The diff is with linus's tree as of this morning.
The device is the RigExpert Tiny USB Soundcard Transceiver Interface for ham
radio.
(I didn't actually test this. A fellow ham couldn't get the device to work, and
I suggested binding the device ID using sysfs - see
"http://jk.ufisa.uninett.no/usb/". However, he had had moved on to other things
by then. I guess adding the device ID to the kernel "on spec" won't hurt.
The relevant part of cat /proc/bus/usb/devices shows:
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0403 ProdID=ed22 Rev= 5.00
S: Manufacturer=FTDI
S: Product=MixW RigExpert Tiny
S: SerialNumber=00000000
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
)
From: Jon K Hellan <hellan@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the range of PIDs
that have been allocated for FTDI based devices
at Matrix Orbital.
A small number of units have been shipped early 2008
with a faulty USB Descriptor. Products that may have
this issue have been marked with the existing quirk to
work around the problem.
Signed-off-by: R. Molenkamp <rmolenkamp@matrixorbital.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch reverts 57833ea6b9
("usb-serial: pl2303: add support for RATOC REX-USB60F") and adds
support for the device to ftdi_sio driver.
Cc: Akira Tsukamoto <akirat@rd.scei.sony.co.jp>
Cc: stable <stable@kernel.org>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch that adds support for the propox jtagcable II dongle
(http://www.propox.com/products/t_117.html): their PID was missing,
therefore we were not able to have the device recognized though it uses
a standard FTDI chip.
Signed-off-by: Mirko Bordignon <mirko.bordignon@ieee.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Workaround for the FT232RL-based, Matrix Orbital VK204-25-USB serial port
added to the ftdi_sio driver.
The device has an invalid endpoint descriptor, which must be modified
before it can be used.
Signed-off-by: Kevin Vance <kvance@kvance.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] ftdi_sio: add support for more FTDI based JTAG adaptors
There are more devices similar to the Olimex JTAG adaptor, in that the first
port of the FT2232C is used for JTAG, and only the second port is available as
UART.
I have thus renamed ftdi_olimex_{probe,quirk} to ftdi_jtag_{probe,quirk} and
added vendor/product ID's for the OpenMoko Neo1973 Debug Board as well as the
OOCDlink device.
I've also updated the KERN_INFO message sent to userspace to remove the word
'olimex' and an extra '\n' that was causing an empty line in dmesg.
Signed-off-by: Harald Welte <laforge@openmoko.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for the Elster Unicom III Optical Probe.
The device ID has already been added to the usb.ids file.
Cc: stable <stable@kernel.org>
Signed-off-by: Ed Beroset <beroset@mindspring.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
little patches only to add vendor/device id of ATK_16IC CCD cam for
astronomy.
From: Franco Lanza <nextime@nexlab.it>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I work with a group of people on a free home automation tool called
FHEM. Some of the users own more than one USB-serial device by ELV. The
ftdi_sio driver has most of the ELV devices disabled by default and
needs to be re-enabled every time you get a new kernel. Additionally a
new device (EM 1010 PC - enegry monitor) is missing in the list.
Currently our users have to follow the instructions we provide at
http://www.koeniglich.de/fhem/linux.html ... However, to some users it
is too complicated to compile their own kernel module.
We are aware that you can specify one additional device using the
vendor/product option of the module. But lot's of users own more than
one device.
Cc: stable <stable@kernel.org>
Signed-off-by: Peter Stark <peter.stark@t-online.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
I have added to a new product based on the FTDI 232R USB/Serial
transceiver, which is commercialized by The Mobility Lab. Here is a
trivial patch enclosed, against 2.6.22.6 kernel.
Signed-off-by: Pierre Castella <pp.castella@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached (mostly trivial) patches adds support for the Evolution
Scorpion Robots.
Evolution Robotics supplies a patch against 2.6.8 with their
software. My patch is based on their work, so I don't know if I can
sign it off, or if you need some Evolution people to do this (which
might be hard).
The patch adds device ID's for some robots which is trivial.
From: Søren Hauberg <hauberg@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Søren
Reported by Grzegorz Chimosz <gchimi@gmail.com>
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the serial port on Olimex arm-usb-ocd
JTAG interface.
The device appears as two serial ports, but the first one is reserved
for the JTAG interface. The JTAG interface can be used with OpenOCD
from userspace. For more information, please see:
http://openocd.berlios.de/web/http://www.olimex.com/dev/arm-usb-ocd.html
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB product id registration for the OpenDCC (www.opendcc.de)
model railway central unit. Applies to 2.6.21.1.
Signed-off-by: Guido Scholz <guido.scholz@bayernline.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hello,
I need to use MaxStream's PKG-U modules which includes a ftdi sio chipset for
usb2serial communication, here are the patches for handling Maxstream's modules.
The VID & PID to use with the open-source driver are provided on the CD-ROM
bundled with the modules.
From: Neil Superna ARMSTRONG <superna@na-prod.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the USB ID of the ADS Tech USBX-707 USB IR blaster (that
comes with the ADS Tech PTV-305 grabber card), which has a ftdi232bm
inside hooked up to a pic.
With this it should be fairly straightforward to make at least lirc
receiving work with this device. I will submit a patch to lirc for that
as soon as I have one ready, I'm getting data with minicom with this
patch, but need to figure out some more details such as best/correct
baudrate.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch adding the PID for the FT232RL to ftdi_sio. The patch
generates a warning during compilation because get_ftdi_divisor doesn't
explicitly handle the FT232RL with this patch, so I guess you don't want
to use it in its current state. It is all I could come up with with the
knowledge I have of the drivers at the moment, though, and I hope you
can have some use for it at least. It works fine with my DLP-TILT with
an FT232RL.
From: Gard Spreemann <spreeman@stud.ntnu.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've developed some devices with FTDI chips (FT232xx). FTDI was so kind
to give some own PID's which I can use together with their VID. Some of
the devices are already very popular here and I have customers from
universities, institutes .....
I use the FTDI VID 0x0403. My PID's are:
0xff38 - IBS US485 (USB<-->RS422/485 interface)
0xff39 - IBS PIC-Programmer
0xff3a - IBS Card reader for PCMCIA SRAM-cards
0xff3b - IBS PK1 - Particel counter
0xff3c - IBS RS232 - Monitor
0xff3d - APP 70 (dust monitoring system)
0xff3e - IBS PEDO-Modem (RF modem 868.35 MHz)
0xff3f - future device
The company is "IBS Ing.-Buero Schleusener".
From: Thomas Schleusener <thomas@be-schl.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like to add the VID and PID for Telldus Technologies Homeautomation
usb-dongle to the ftdi_sio driver.
From: Micke Prag <micke.prag@telldus.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
below is a patch for the ftdi_sio driver to include a new device ID for
CCS MachX PIC programmer.
From: Jan Capek <jan@ccsinfo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Please add a usb pid to the ftdi_sio driver. The pid is used by dmx4all
dmx-interfaces (for stage lighting).
The interfaces are using the usb-id 0403:c850. I added the id to the driver
and it works perfectly. I added a patch for linux 2.6.18.1, too.
From: Frank Sievertsen <frank@sievertsen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds the vendor and prodcut id for a RFID construction kit from the
Elektor Electronics magazine, september 2006.
From: Kjell Myksvoll <kmyksvo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have a couple of these USB-Serial converters around; they're slightly
different from the 2104 models in that they can handle 500Kb/sec over RS422.
The existing ftdi driver seems to work just fine if we add in the
appropriate IDs.
Patch is against 2.6.17.6, but should apply cleanly to pretty much
anything recent.
From: Justin Carlson <justinca@qatar.cmu.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for three OpenPort ECU data cables from Tactrix
Inc. to the ftdi_sio driver's device ID table. One of the PIDs was
supplied by Donour Sizemore on the ftdi-usb-sio-devel mailing list. The
other two were added by myself after examining the Windows driver software.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch adds a new device ID for the Gamma Scout Geiger counter
device.
Signed-off-by: Ralf Schlatterbeck <rsc@runtux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a short patch which adds one PID to the set of devices
supported by the ftdi_sio driver. The device in question is a
DLP module used as part of a ham radio USB-to-packet adapter.
From: Dave Platt <dplatt@radagast.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the Testo USB interface to the list of devices
recognized by the ftdi_sio module. This device is based on a FT232BL
chip, and is used as an interface to get data from digital sensors
(thermometer, etc). See http://www.testo.com/
Signed-off-by: Colin Leroy <colin@colino.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for Yost Engineering Inc's ServoCenter 3.1 USB
product to the ftdi_sio driver's device ID table. The PID was supplied
by Aaron Prose of Yost Engineering on the ftdi-usb-sio-devel list. The
PID 0xE050 matches the Windows INF files for this device.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for ACG Identification Technologies GmbH's HF
Dual ISO Reader (an RFID tag reader) to the ftdi_sio driver's device ID
table. The product ID was supplied by anotonios (anton at goto10 dot
org) on the ftdi-usb-sio-devel list and subsequently verified by myself
(Ian Abbott).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for an ASK RDR 400 series contactless card
reader <http://www.ask.fr/uk/products_and_services/terminals.html> to
the ftdi_sio driver's device ID table. The product ID was supplied by
Adriano Couto on the ftdi-usb-sio-devel list.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support in ftdi_sio usbserial driver for USB modems sold by
Plus GSM Company in Poland.
Signed-off-by: Luiz Fernando Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds recognition of the RR-CirKits LocoBuffer USB
to the existing FTDI driver. http://www.rr-cirkits.com
Signed-off-by: Nathan Bronson <ngb@sns-usa.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the Eclo COM to 1-Wire USB adapter
<http://www.eclo.pt/products_ibutton_adapters_usb01_en.asp> to the
ftdi_sio driver's device ID table. Details were provided by Martin
Grill on the ftdi-sio-usb-devel mailing list and I (Ian Abbott)
confirmed it matched the INF file in the Eclo's Windows driver package.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Icom ID-1 1.2 GHz band digital transceiver is a new radio
that has a USB interface. With this patch, the ftdi_sio driver
will report "Detected FT8U232AM" and provide a serial device
interface.
Signed-off-by: "A. Maitland Bottoms" <bottoms@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a bunch of new device IDs to the ftdi_sio driver for
various devices from microHAM using FTDI chips.
Micheal Studer supplied the PID for the USB-Y9 device. I examined the
INF file in microHAM's Windows driver package for the USB-KW, USB-YS,
USB-IC, USB-DB9 and USB-RS232 devices.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation: Specify grayscale specification on ATIK-ATK16
and ATIK-ATK16HR comments.
New: Add ProductID and VendorID for devices ATIK-ATK16C and
ATIK-ATK16HRC. These devices are also USB Astronomical CCD
cameras that work through an FTDI 245BM chip, share the
same base hardware but, it has a colour CCD chip instead
of a grayscale one.
Signed-off-by: Rui Santos <rsantos@grupopie.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch adds a new PID for the ftdi_sio driver. It will
enable support for PC-DJ's DAC-2 controller module
(more information on http://www.pcdjhardware.com/DAC2.asp)
Signed-off-by: Wouter Paesen <wouter@kangaroot.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds two new devices to the ftdi_sio driver's device ID
table. The device IDs were supplied by Cory Lee to support two POS
printers made by Westrex International (Model 777 and Model 8900F).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch includes the Vendor Id for a optic fiber to USB device named
TTUSB from thought Technology. It's just add the vendor Id to
ftdi_sio.h and add the Vendor ID and model Id to table_combined.
Signed-off-by: Louis Nyffenegger <louis.nyffenegger@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
![](/avatar/362e80bc9fa0d4c6d6e2a8a86ae5d0d0?size=56 "Neil \\"Superna\\" ARMSTRONG"){kind=small}
