The .get method is needed for suspend/resume. Otherwise you
get this in dmesg:
cpufreq: suspend failed to assert current frequency is what timing core thinks it is.
cpufreq: resume failed to assert current frequency is what timing core thinks it is.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The QNAP TS-209 has its RTC interrupt on GPIO 3. Setup this
as an interrupt and pass it to the i2c_board_info.
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that the clock lookup always finds an entry for a specific
device and ID before it falls back to finding just by ID. This
fixes a problem reported by Holger Schurig where the BTUART was
assigned the wrong clock.
Tested-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
[ARM] constify function pointer tables
[ARM] 4823/1: AT91 section fix
[ARM] 4824/1: pxa: clear RDH bit after any reset
[ARM] pxa: remove debugging PM: printk
ARM: OMAP1: Misc clean-up
ARM: OMAP1: Update defconfigs for omap1
ARM: OMAP1: Palm Tungsten E board clean-up
ARM: OMAP1: Use I2C bus registration helper for omap1
ARM: OMAP1: Remove omap_sram_idle()
ARM: OMAP1: PM fixes for OMAP1
ARM: OMAP1: Use MMC multislot structures for Siemens SX1 board
ARM: OMAP1: Make omap1 use MMC multislot structures
ARM: OMAP1: Change the comments to C style
ARM: OMAP1: Make omap1 boards to use omap_nand_platform_data
ARM: OMAP: Add helper module for board specific I2C bus registration
ARM: OMAP: Add dmtimer support for OMAP3
ARM: OMAP: Pre-3430 clean-up for dmtimer.c
ARM: OMAP: Add DMA support for chaining and 3430
ARM: OMAP: Add 24xx GPIO debounce support
ARM: OMAP: Get rid of unnecessary ifdefs in GPIO code
...
* master:
[ARM] constify function pointer tables
[ARM] 4823/1: AT91 section fix
[ARM] 4824/1: pxa: clear RDH bit after any reset
[ARM] pxa: remove debugging PM: printk
* omap1-upstream:
ARM: OMAP1: Misc clean-up
ARM: OMAP1: Update defconfigs for omap1
ARM: OMAP1: Palm Tungsten E board clean-up
ARM: OMAP1: Use I2C bus registration helper for omap1
ARM: OMAP1: Remove omap_sram_idle()
ARM: OMAP1: PM fixes for OMAP1
ARM: OMAP1: Use MMC multislot structures for Siemens SX1 board
ARM: OMAP1: Make omap1 use MMC multislot structures
ARM: OMAP1: Change the comments to C style
ARM: OMAP1: Make omap1 boards to use omap_nand_platform_data
ARM: OMAP: Add helper module for board specific I2C bus registration
ARM: OMAP: Add dmtimer support for OMAP3
ARM: OMAP: Pre-3430 clean-up for dmtimer.c
ARM: OMAP: Add DMA support for chaining and 3430
ARM: OMAP: Add 24xx GPIO debounce support
ARM: OMAP: Get rid of unnecessary ifdefs in GPIO code
ARM: OMAP: Add 3430 gpio support
ARM: OMAP: Add 3430 CPU identification macros
ARM: OMAP: Request DSP memory for McBSP
* orion:
[ARM] Orion: Use the sata_mv driver for the TS-209 SATA
[ARM] Orion: Use the sata_mv driver for the Kurobox SATA
[ARM] Orion: free up kernel virtual address space
[ARM] Orion: distinguish between physical and virtual addresses
[ARM] Orion: kill orion_early_putstr()
[ARM] Orion: update defconfig
[ARM] Orion: Use the sata_mv driver for the integrated SATA controller
Fix section warning:
WARNING: arch/arm/mach-at91/built-in.o(.text+0xd74): Section mismatch in reference
from the function init_programmable_clock()
to the function .init.text:at91_css_to_clk()
The function init_programmable_clock() references
the function __init at91_css_to_clk().
This is often because init_programmable_clock lacks a __init
annotation or the annotation of at91_css_to_clk is wrong.
In this case the only calls to and from init_programmable_clock()
are from code marked as "__init", so this fix is trivially correct.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Uwe Kleine-Knig <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to PXA300/310 and PXA320 Developer manuals,
the ASCR[RDH] "bit needs to be cleared as part of the software
initialization coming out of any reset and coming out of D3".
The latter requirement is addressed by commit
"c4d1fb627ff3072", as for the former (coming out of any reset),
the kernel relies on boot loaders and assumes that RDH bit
is cleared there. Though, not all bootloaders follow the rule
so we have to clear the bit in kernel.
We clear the RDH bit in pxa3xx_init() function since
it is always invoked after any reset. We also preserve D1S, D2S
and D3S bits from being cleared in case we invoke pxa3xx_init()
function not from normal hardware reset (e.g. kexec scenario),
so these bits can be properly referenced later.
Signed-off-by: Dmitry Krivoschekov <dmitry.krivoschekov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To allow flexible configuration of IDE introduce HAVE_IDE.
All archs except arm, um and s390 unconditionally select it.
For arm the actual configuration determine if IDE is supported.
This is a step towards introducing drivers/Kconfig for arm.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch cleans up omap1 files to sync up with linux-omap tree:
- Remove omap-generic MMC config as it should be defined in board-*.c files
instead of using board-generic.c
- New style I2C board_info from David Brownell <dbrownell@users.sourceforge.net>
- Init section fixes from Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch starts using introduced I2C bus registration helper by cleaning
up registration currently done in various places and by doing necessary
board file modifications.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes omap_sram_idle() that is no longer used.
The function called in pm_idle is omap_sram_suspend, omap_sram_idle() is
not used anywhere in omap1.
Signed-off-by: Vivek Kutal <vivek.kutal@celunite.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch does the following:
- Fixes the omap_pm_idle() code so that we enter WFI mode in idle.
- /sys/power/sleep_while_idle is created only when 32k timer is used
Signed-off-by: Vivek Kutal <vivek.kutal@celunite.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use MMC multislot structures for Siemens SX1 board
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make omap1 use new MMC multislot structures. The related MMC
patches will be sent separately.
Signed-off-by: Felipe Balbi <felipe.lima@indt.org.br>
Signed-off-by: Anderson Briglia <anderson.briglia@indt.org.br>
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: David Cohen <david.cohen@indt.org.br>
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds omap_nand_platform data based on a patch
by Shahrom Sharif-Kashani <sshahrom@micron.com>, and makes
omap1 boards to use omap_nand_platform_data instead of
nand_platform_data used earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This helper module simplifies I2C bus registration for different OMAP
platforms by doing registration in one place only and to allow board
specific bus configuration like clock rate and number of busses configured.
Helper should cover OMAP processors from first to third generation.
This patch just adds the feature and current implementation cleanup and
board file modifications will be done in following patches.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DM timer support for OMAP3.
Fixed source clocks for 3430 by Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cleanup DM timer list for OMAP2 and OMAP1 to allow
adding support for 3430.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DMA support for chaining and 3430.
Also remove old DEBUG_PRINTS as noted by Russell King.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add 24xx GPIO debounce support. Also minor formatting
clean-up.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds 3430 gpio support.
It also contains a fix by Paul Walmsley <paul@pwsan.com> to use the
correct clock names for OMAP3430.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP1 some McBSP features depend on DSP. Also export
polling functions as suggested by Luis Cargnini.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The TS-209 has a two port integrated SATA controller.
Use the sata_mv driver for this.
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The Kurobox has a two port integrated SATA controller.
Use the sata_mv driver for this.
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Suppress A.OUT library support if CONFIG_ARCH_SUPPORTS_AOUT is not set.
Not all architectures support the A.OUT binfmt, so the ELF binfmt should not
be permitted to go looking for A.OUT libraries to load in such a case. Not
only that, but under such conditions A.OUT core dumps are not produced either.
To make this work, this patch also does the following:
(1) Makes the existence of the contents of linux/a.out.h contingent on
CONFIG_ARCH_SUPPORTS_AOUT.
(2) Renames dump_thread() to aout_dump_thread() as it's only called by A.OUT
core dumping code.
(3) Moves aout_dump_thread() into asm/a.out-core.h and makes it inline. This
is then included only where needed. This means that this bit of arch
code will be stored in the appropriate A.OUT binfmt module rather than
the core kernel.
(4) Drops A.OUT support for Blackfin (according to Mike Frysinger it's not
needed) and FRV.
This patch depends on the previous patch to move STACK_TOP[_MAX] out of
asm/a.out.h and into asm/processor.h as they're required whether or not A.OUT
format is available.
[jdike@addtoit.com: uml: re-remove accidentally restored code]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark arches that support A.OUT format by including the following in their
master Kconfig files:
config ARCH_SUPPORTS_AOUT
def_bool y
This should also be set if the arch provides compatibility A.OUT support for
an older arch, for instance x86_64 for i386 or sparc64 for sparc.
I've guessed at which arches don't, based on comments in the code, however I'm
sure that some of the ones I've marked as 'yes' actually should be 'no'.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hack up the Orion port to distinguish between virtual and physical
addresses of register windows. This will allow moving virtual
mappings higher up in the address space, to free up more kernel
virtual address space.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch adds instantiation for the sata_mv driver, enabling the
integrated SATA controller.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Add HP Jornada 6xx driver
leds: Remove the now uneeded ixp4xx driver
leds: Add power LED to the wrap driver
leds: Fix led-gpio active_low default brightness
leds: hw acceleration for Clevo mail LED driver
leds: Add support for hardware accelerated LED flashing
leds: Standardise LED naming scheme
leds: Add clevo notebook LED driver
This patchset adds a flags variable to reserve_bootmem() and uses the
BOOTMEM_EXCLUSIVE flag in crashkernel reservation code to detect collisions
between crashkernel area and already used memory.
This patch:
Change the reserve_bootmem() function to accept a new flag BOOTMEM_EXCLUSIVE.
If that flag is set, the function returns with -EBUSY if the memory already
has been reserved in the past. This is to avoid conflicts.
Because that code runs before SMP initialisation, there's no race condition
inside reserve_bootmem_core().
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix powerpc build]
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: <linux-arch@vger.kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As discussed on LKML some notion of 'function' is needed in
LED naming. This patch adds this to the documentation and
standardises existing LED drivers.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata_piix.c:piix_init_one() must be __devinit
sata_via.c: Remove missleading comment.
libata-core: unblacklist HITACHI drives
sata_nv: fix ATAPI issues with memory over 4GB (v7)
ata: drivers/ata/sata_mv.c needs dmapool.h
libata: kill now unused n_iter and fix sata_fsl
ahci: fix CAP.NP and PI handling
sata_mv: Support SoC controllers
Rename: linux/pata_platform.h to linux/ata_platform.h
On the sam9 EK boards, the LCD backlight is hooked up to a PWM output from
the LCD controller. It's controlled by "contrast" registers though.
This patch lets boards declare that they have that kind of backlight
control. The driver can then export this control, letting screenblank and
other operations actually take effect ... reducing the typically
substantial power drain from the backlight.
Note that it's not fully cooked
- doesn't force backlight off during system suspend
- the "power" and "blank" events may not be done right
This should be easily added in the future.
[nicolas.ferre@atmel.com: remove unneeded inline and rename functions]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(with Martin Schwidefsky <schwidefsky@de.ibm.com>)
The pgd/pud/pmd/pte page table allocation functions get a mm_struct pointer as
first argument. The free functions do not get the mm_struct argument. This
is 1) asymmetrical and 2) to do mm related page table allocations the mm
argument is needed on the free function as well.
[kamalesh@linux.vnet.ibm.com: i386 fix]
[akpm@linux-foundation.org: coding-syle fixes]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds gpiolib support for the PXA architecture:
- move all GPIO API functions from generic.c into gpio.c
- convert the gpio_get/set_value macros into inline functions
This makes it easier to hook up GPIOs provided by external chips like
ASICs and CPLDs.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Minor ARM fixup from David Brownell folded into this ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an empty drivers/gpio directory for gpiolib infrastructure and GPIO
expanders. It will be populated by later patches.
This won't be the only place to hold such gpio_chip code. Many external chips
add a few GPIOs as secondary functionality (such as MFD drivers) and platform
code frequently needs to closely integrate GPIO and IRQ support.
This is placed *early* in the build/link sequence since it's common for other
drivers to depend on GPIOs to do their work, so they must be initialized early
in the device_initcall() sequence.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the new timerfd API as it is implemented by the following patch:
int timerfd_create(int clockid, int flags);
int timerfd_settime(int ufd, int flags,
const struct itimerspec *utmr,
struct itimerspec *otmr);
int timerfd_gettime(int ufd, struct itimerspec *otmr);
The timerfd_create() API creates an un-programmed timerfd fd. The "clockid"
parameter can be either CLOCK_MONOTONIC or CLOCK_REALTIME.
The timerfd_settime() API give new settings by the timerfd fd, by optionally
retrieving the previous expiration time (in case the "otmr" parameter is not
NULL).
The time value specified in "utmr" is absolute, if the TFD_TIMER_ABSTIME bit
is set in the "flags" parameter. Otherwise it's a relative time.
The timerfd_gettime() API returns the next expiration time of the timer, or
{0, 0} if the timerfd has not been set yet.
Like the previous timerfd API implementation, read(2) and poll(2) are
supported (with the same interface). Here's a simple test program I used to
exercise the new timerfd APIs:
http://www.xmailserver.org/timerfd-test2.c
[akpm@linux-foundation.org: coding-style cleanups]
[akpm@linux-foundation.org: fix ia64 build]
[akpm@linux-foundation.org: fix m68k build]
[akpm@linux-foundation.org: fix mips build]
[akpm@linux-foundation.org: fix alpha, arm, blackfin, cris, m68k, s390, sparc and sparc64 builds]
[heiko.carstens@de.ibm.com: fix s390]
[akpm@linux-foundation.org: fix powerpc build]
[akpm@linux-foundation.org: fix sparc64 more]
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
...
* at91:
[ARM] 4802/1: Fix typo and remove vague comment
[ARM] 4660/3: at91: allow selecting UART for early kernel messages
[ARM] 4739/1: at91sam9263: make gpio bank C and D irqs work
* ixp:
[ARM] 4809/2: ixp4xx: Merge dsmg600-power.c into dsmg600-setup.c
[ARM] 4808/2: ixp4xx: Merge nas100d-power.c into nas100d-setup.c
[ARM] 4807/2: ixp4xx: Merge nslu2-power.c into nslu2-setup.c
[ARM] 4806/1: ixp4xx: Ethernet support for the nslu2 and nas100d boards
[ARM] 4805/1: ixp4xx: Use leds-gpio driver instead of IXP4XX-GPIO-LED driver
[ARM] 4715/2: Ethernet support for IXDP425 boards
[ARM] 4714/2: Headers for IXP4xx built-in Ethernet and WAN drivers
[ARM] 4713/3: Adds drivers for IXP4xx QMgr and NPE features
[ARM] 4712/2: Adds functions to read and write IXP4xx "feature" bits
[ARM] 4774/2: ixp4xx: Register dsmg600 rtc i2c_board_info
[ARM] 4773/2: ixp4xx: Register nas100d rtc i2c_board_info
[ARM] 4772/2: ixp4xx: Register nslu2 rtc i2c_board_info
[ARM] 4769/2: ixp4xx: Button updates for the dsmg600 board
[ARM] 4768/2: ixp4xx: Button and LED updates for the nas100d board
[ARM] 4767/2: ixp4xx: Add bitops.h include to io.h
[ARM] 4766/2: ixp4xx: Update ixp4xx_defconfig, enabling all supported boards
* master:
[ARM] 4810/1: - Fix 'section mismatch' building warnings
[ARM] xtime_seqlock: fix more ARM machines for xtime deadlocking
[ARM] 21285 serial: fix build error
* misc:
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
* pxa:
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
[ARM] pxa: fix the warning of undeclared "struct pxaohci_platform_data"
[ARM] pxa: change set_kset_name() to direct name assignment for MFP sysclass
* realview:
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
This patch changes the REALVIEW_MPCORE configuration option to
REALVIEW_EB_ARM11MP since this is only specific to RealView/EB.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
