Tegra's UART is currently auto-detected as PORT_XSCALE due to register
bit UART_IER.UUE being writable. However, the Tegra documentation states
that this register bit is reserved. Hence, we should not program it.
Instead, the documentation specifies that the UART is 16550 compatible.
However, Tegra does need register bit UART_IER.RTOIE set, which is not
enabled by any 16550 port type. This was not noticed before, since
PORT_XSCALE enables CAP_UUE, which conflates both UUE and RTOIE bit
programming.
This change defines PORT_TEGRA that doesn't set UART_CAP_UUE, but does
set UART_CAP_RTOIE, which is a new capability indicating that the RTOIE
bit needs to be enabled.
Based-on-code-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to removing ARCH_S5P6442, we don't need to support
serial for S5P6442.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support to the 8250 PCI serial driver for the Digi/IBM PCIe 2-port Async EIA-232 Adapter.
Oxford Semiconductor produces a 2/4/8 port UART (OXPCIe952/OXPCIe954/OXPCIe958) chip
called the Tornado, that can be used to create a very simple serial board product.
The kernel sources currently have just 2 vendors using this chip, which is Oxford and Mainpipe.
This new Digi/IBM serial product now uses it as well.
Rather than create a long running comment of vendors using the chip, the one changed comment
in the patch below now just lists "For Oxford Semiconductor Tornado based devices" to be a
more generic comment for all vendors that end up using the Oxford Tornado chip.
Cc: Michael Reed <mreed10@us.ibm.com>
Signed-off-by: Scott Kilau <scottk@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Xilinx PS Uart is used on the new ARM based SoC. This
UART is not compatible with others such that a seperate
driver is required.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
msleep* is guaranteed to return with TASK_RUNNING task state. And
since there is no other set_task_state in the paths of
uart_wait_until_sent, we need not to set_task_state to TASK_RUNNING.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tty->index (named here as line) is set up in initialize_tty_struct.
The value is checked in get_tty_driver for the found driver as:
if (device < base || device >= base + p->num)
continue;
*index = device - base;
So index/line can never be more than driver->num. Hence remove this
test from uart_open.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Including linux/tty.h 3 times is a little over the top - once will do.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
remove invalid location line in each file header after location
moved from driver/char to driver/tty
Signed-off-by: Jovi Zhang <bookjovi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now, uart_update_termios is empty, so it's time to remove it. We no
longer need a live tty in .dtr_rts. So this should prune all the bugs
where tty is zeroed in port->tty during tty_port_block_til_ready.
There is one thing to note. We don't set ASYNC_NORMAL_ACTIVE now. It's
because this is done already in tty_port_block_til_ready.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In .dtr_rts we do:
uart_set_mctrl(uport, TIOCM_DTR | TIOCM_RTS)
and call uart_update_termios. It does:
uart_set_mctrl(port, TIOCM_DTR | TIOCM_RTS)
once again. As the only callsite of uart_update_termios is .dtr_rts,
remove the uart_set_mctrl from uart_update_termios to not set it twice.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should not fiddle with speed and cflags in .dtr_rts hook. Actually
we might not have tty at that moment already.
So move the console cflag copy and speed setup into uart_startup.
Actually the speed setup is already there, but we need to call it
unconditionally (uart_startup is called from uart_open with hw_init =
0).
This means we move uart_change_speed before dtr/rts setup in .dtr_rts.
But this should not matter as the setup should be called after
uart_change_speed anyway.
Before: After:
dtr/rts setup (dtr_rts) uart_change_speed (startup)
uart_change_speed (update_termios) dtr/rts setup (dtr_rts)
dtr/rts setup (update_termios) dtr/rts setup (update_termios)
The second setup will dismiss with the next patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Devices extracted from device tree all seem to have pdev->id set to -1.
Up until now we mapped all devices with id -1 to the first device. This
behaviour could lead to problems when using more than one Altera UART in
a system.
This patch changes the behaviour of the driver to scan for the next free
id in case the id is -1.
Because we cannot refer back to the assigned id in altera_uart_remove,
the port instance needs to be stored in device drvdata.
Reported-by: David Smoot <davidsmoot@gmail.com>
Cc: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver is initialized in a state with an unknown value by
serial_console_setup. And initialization fails.
This is caused by the initialization by sci_console_init.
This function does not seem to be necessary for the present sh-sci driver.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 906b17dc08 introduced a condition
where the kernel will crash unless a earlyprintk parameter is specified.
Without this parameter, sci_console_init is called during early console
setup without any port being initialized, and the kernel crashes a
little bit later when uart_set_options attemps to invoke set_termios on a
port with an ops member equal to NULL.
This patch just checks in sci_console_init that the port is properly
initialized, and aborts the early console setup if it is not.
Signed-off-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It absolutely needs to be able to get at pdev_archdata members
which are sparc specific.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
The UARTs may be located on different APB buses, thus have
different UART clock frequency. The system frequency is not
the same (but often) as the UART frequency, rather the APB bus
frequency that the APBUART is located at has the same
frequency, so this looks at the "freq" property instead.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
See Commit id 1636f8ac2b (sparc/of:
Move of_device fields into struct pdev_archdata), this patch
is similar to 19e4875fb2 (of/sparc:
fix build regression from of_device changes)
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kdb: add usage string of 'per_cpu' command
kgdb,x86_64: fix compile warning found with sparse
kdb: code cleanup to use macro instead of value
kgdboc,kgdbts: strlen() doesn't count the terminator
This is an off by one because strlen() doesn't count the null
terminator. We strcpy() these strings into an array of size
MAX_CONFIG_LEN.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
* 'for-linus' of git://codeaurora.org/quic/kernel/davidb/linux-msm: (46 commits)
msm: scm: Check for interruption immediately
msm: scm: Fix improper register assignment
msm: scm: Mark inline asm as volatile
msm: iommu: Enable HTW L2 redirection on MSM8960
msm: iommu: Don't read from write-only registers
msm: iommu: Remove dependency on IDR
msm: iommu: Use ASID tagging instead of VMID tagging
msm: iommu: Rework clock logic and add IOMMU bus clock control
msm: iommu: Clock control for the IOMMU driver
msm: mdp: Set the correct pack pattern for XRGB/ARGB
msm_fb: Fix framebuffer console
msm: mdp: Add support for RGBX 8888 image format.
video: msmfb: Put the partial update magic value into the fix_screen struct.
msm: clock: Migrate to clkdev
msm: clock: Remove references to clk_ops_pcom
msm: headsmp.S: Fix section mismatch
msm: Use explicit GPLv2 licenses
msm: iommu: Enable IOMMU support for MSM8960
msm: iommu: Generalize platform data for multiple targets
msm: iommu: Create a Kconfig item for the IOMMU driver
...
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
* 'defcfg' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6647/1: add Versatile Express defconfig
ARM: 6644/1: mach-ux500: update the U8500 defconfig
* 'drivers' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6764/1: pl011: factor out FIFO to TTY code
ARM: 6763/1: pl011: add optional RX DMA to PL011 v2
ARM: 6758/1: amba: support pm ops
ARM: amba: make amba_driver id_table const
ARM: amba: make internal ID table handling const
ARM: amba: make probe() functions take const id tables
ARM: 6662/1: amba: make amba_bustype non-static
ARM: mmci: add dmaengine-based DMA support
ARM: mmci: no need for separate host->data_xfered
ARM: mmci: avoid unnecessary switch to data available PIO interrupts
ARM: mmci: no need to call flush_dcache_page() with sg_miter API
ARM: mmci: avoid reporting too many completed bytes on fifo overrun
ALSA: AACI: make fifo variables more explanitory
ALSA: AACI: no need to call snd_pcm_period_elapsed() for each period
ALSA: AACI: use snd_pcm_lib_period_bytes()
ALSA: AACI: clean up AACI announcement printk
ALSA: AACI: fix channel mask selection
ALSA: AACI: fix number of channels for record
ALSA: AACI: fix multiple IRQ claiming
* 'cyberpro-next' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: remove unused cyber2000fb_get_fb_var()
VIDEO: cyberpro: remove useless function extreg pointers
VIDEO: cyberpro: update handling of device structures
VIDEO: cyberpro: add support for video capture I2C
VIDEO: cyberpro: make 'reg_b0_lock' always present
VIDEO: cyberpro: add I2C support
VIDEO: cyberpro: select lowest multipler/divisor for PLL
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (76 commits)
pch_uart: reference clock on CM-iTC
pch_phub: add new device ML7213
n_gsm: fix UIH control byte : P bit should be 0
n_gsm: add a documentation
serial: msm_serial_hs: Add MSM high speed UART driver
tty_audit: fix tty_audit_add_data live lock on audit disabled
tty: move cd1865.h to drivers/staging/tty/
Staging: tty: fix build with epca.c driver
pcmcia: synclink_cs: fix prototype for mgslpc_ioctl()
Staging: generic_serial: fix double locking bug
nozomi: don't use flush_scheduled_work()
tty/serial: Relax the device_type restriction from of_serial
MAINTAINERS: Update HVC file patterns
tty: phase out of ioctl file pointer for tty3270 as well
tty: forgot to remove ipwireless from drivers/char/pcmcia/Makefile
pch_uart: Fix DMA channel miss-setting issue.
pch_uart: fix exclusive access issue
pch_uart: fix auto flow control miss-setting issue
pch_uart: fix uart clock setting issue
pch_uart : Use dev_xxx not pr_xxx
...
Fix up trivial conflicts in drivers/misc/pch_phub.c (same patch applied
twice, then changes to the same area in one branch)
Add a call to of_node_put in the error handling code following a call to
of_find_compatible_node or of_find_node_by_type.
This patch also substantially reorganizes the error handling code in the
function, to that it is possible first to jump to code that frees qe_port
and then to jump to code that also puts np.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E,E1,E2;
statement S;
@@
*x =
(of_find_node_by_path
|of_find_node_by_name
|of_find_node_by_phandle
|of_get_parent
|of_get_next_parent
|of_get_next_child
|of_find_compatible_node
|of_match_node
|of_find_node_by_type
|of_find_node_with_property
|of_find_matching_node
|of_parse_phandle
)(...);
...
if (x == NULL) S
<... when != x = E
*if (...) {
... when != of_node_put(x)
when != if (...) { ... of_node_put(x); ... }
(
return <+...x...+>;
|
* return ...;
)
}
...>
(
E2 = x;
|
of_node_put(x);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Default clock source for UARTs on Topcliff is external UART_CLK.
On CM-iTC USB_48MHz is used instead. After VCO2PLL and DIV
manipulations UARTs will receive 192 MHz.
Clock manipulations on Topcliff are controlled in pch_phub.c
v2: redone against the linux-next tree
v3: redone against linux/kernel/git/next/linux-next.git snapshot
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This piece of code was just slightly different between the DMA
and IRQ paths, in DMA mode we surely shouldn't read more than
256 character either, so factor this out in its own function and
use for both DMA and PIO mode.
Tested on Ux500 and U300.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds an optional RX DMA codepath for the devices that
support this by using the apropriate burst sizes instead of
pulling single bytes.
Includes portions of code written by Russell King during
a PL08x hacking session.
This has been tested on U300 and Ux500.
Tested-by: Jerzy Kasenberg <jerzy.kasenberg@tieto.com>
Tested-by: Grzegorz Sygieda <grzegorz.sygieda@tieto.com>
Tested-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Per Forlin <per.friden@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This driver supports UART-DM HW on MSM platforms. It uses the on
chip DMA to drive data transfers and has optional support for UART
power management independent of Linux suspend/resume and wakeup
from Rx.
The driver was originally developed by Google. It is functionally
equivalent to the version available at:
http://android.git.kernel.org/?p=kernel/experimental.git
the differences being:
1) Remove wakelocks and change unsupported DMA API.
2) Replace clock selection register codes by macros.
3) Fix checkpatch errors and add inline documentation.
4) Add runtime PM hooks for active power state transitions.
5) Handle error path and cleanup resources if required.
CC: Nick Pelly <npelly@google.com>
Signed-off-by: Sankalp Bose <sankalpb@codeaurora.org>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
S3 sleep invokes the shutdown callback of the sh-sci driver, which
suspends the clocks until they are reactivated by a call to startup.
However, before the latter is invoked, sci_set_termios may be called on
the port by uart_resume_port. In such cases it will endlessly wait for
the TEND bit to raise, which will never happen since the clocks are
disabled.
This patch ensures that clocks are enabled when ports registers are
manipulated within sci_set_termios.
Signed-off-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Advertise the possibility to use this driver with device tree if
CONFIG_OF is set.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
With the recent switch of the (currently still out-of-tree) Nios2 Linux
port to devicetree we want to be able to retrieve the resources and
properties from dts.
The old method to retrieve resources and properties from platform data
is still supported.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
