FSG_NUM_BUFFERS is set to 2 as default.
Usually 2 buffers are enough to establish a good buffering pipeline.
The number may be increased in order to compensate a for bursty VFS
behaviour.
Here follows a description of system that may require more than
2 buffers.
* CPU ondemand governor active
* latency cost for wake up and/or frequency change
* DMA for IO
Use case description.
* Data transfer from MMC via VFS to USB.
* DMA shuffles data from MMC and to USB.
* The CPU wakes up every now and then to pass data in and out from VFS,
which cause the bursty VFS behaviour.
Test set up
* Running dd on the host reading from the mass storage device
* cmdline: dd if=/dev/sdb of=/dev/null bs=4k count=$((256*100))
* Caches are dropped on the host and on the device before each run
Measurements on a Snowball board with ondemand_governor active.
FSG_NUM_BUFFERS 2
104857600 bytes (105 MB) copied, 5.62173 s, 18.7 MB/s
104857600 bytes (105 MB) copied, 5.61811 s, 18.7 MB/s
104857600 bytes (105 MB) copied, 5.57817 s, 18.8 MB/s
FSG_NUM_BUFFERS 4
104857600 bytes (105 MB) copied, 5.26839 s, 19.9 MB/s
104857600 bytes (105 MB) copied, 5.2691 s, 19.9 MB/s
104857600 bytes (105 MB) copied, 5.2711 s, 19.9 MB/s
There may not be one optimal number for all boards. This is why
the number is added to Kconfig. If selecting USB_GADGET_DEBUG_FILES
this value may be set by a module parameter as well.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The ARCH_MX1 scheduled for removal. Instead, depend on ARCH_MXC
and make clear in the Kconfig text that only i.MX1 has this
hardware.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DesignWare USB3 is a highly
configurable IP Core which can be
instantiated as Dual-Role Device (DRD),
Peripheral Only and Host Only (XHCI)
configurations.
Several other parameters can be configured
like amount of FIFO space, amount of TX and
RX endpoints, amount of Host Interrupters,
etc.
The current driver has been validated with
a virtual model of version 1.73a of that core
and with an FPGA burned with version 1.83a
of the DRD core. We have support for PCIe
bus, which is used on FPGA prototyping, and
for the OMAP5, more adaptation (or glue)
layers can be easily added and the driver
is half prepared to handle any possible
configuration the HW engineer has chosen
considering we have the information on
one of the GHWPARAMS registers to do
runtime checking of certain features.
More runtime checks can, and should, be added
in order to make this driver even more flexible
with regards to number of endpoints, FIFO sizes,
transfer types, etc.
While this supports only the device side, for
now, we will add support for Host side (xHCI -
see the updated series Sebastian has sent [1])
and OTG after we have it all stabilized.
[1] http://marc.info/?l=linux-usb&m=131341992020339&w=2
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After 622859634 (usb: musb: drop a gigantic amount of ifdeferry):
- USB_GADGET_MUSB_HDRC is no longer selectable because it
depends on the removed USB_MUSB_PERIPHERAL and USB_MUSB_OTG
options
- The Kconfig comment still says "Enable Host or Gadget support
to see Inventra options", even though you now need to enable
both of them to see Inventra options.
Fix the dependency and drop the anyway unnecessary comment.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch rescues renesas_usbhs compile from
commit 193ab2a (usb: gadget: allow multiple gadgets to be built)
CONFIG_USB_RENESAS_USBHS compile renesas_usbhs main code which
is shared between Host/Gadget.
CONFIG_USB_RENESAS_USBHS_UDC add mod_gadget to it.
It had lost USB_GADGET_DUALSPEED
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Both fusb300 and langwell udcs seem to only
work with 32-bit address space.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that we have the udc class, we can allow
multiple gadget controller drivers to be
compiled as modules. This will allow for
distro-like kernels for embedded devices.
With this patch, I managed to build an x86
kernel with support for many of the controllers
enabled:
CONFIG_USB_FUSB300=m
CONFIG_USB_R8A66597=m
CONFIG_USB_M66592=m
CONFIG_USB_AMD5536UDC=m
CONFIG_USB_CI13XXX_PCI=m
CONFIG_USB_NET2272=m
CONFIG_USB_NET2280=m
CONFIG_USB_GOKU=m
CONFIG_USB_LANGWELL=m
CONFIG_USB_EG20T=m
Also an ARM kernel with support for many controllers:
CONFIG_USB_FUSB300=m
CONFIG_USB_OMAP=m
CONFIG_USB_R8A66597=m
CONFIG_USB_GADGET_MUSB_HDRC=m
CONFIG_USB_M66592=m
CONFIG_USB_NET2272=m
CONFIG_USB_DUMMY_HCD=m
The next step would be to get rid of the
direct access to arch/ and mach/ directories
on some gadget controllers so that we can
build all of them without depending on their
respective ARCH_* symbols.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds SS support to the dummy hcd module.
It may be used to test SS device when no (SS) HW is
available.
USB 3.0 hub includes 2 hubs - one HS and one SS. This
patch adds support for a SS root hub in the dummy_hcd
module.
A new module parameter was added: is_super_speed. When
set to true, a SS root hub will also be registered and
the connected device will be enumerated over the SS
root hub. The default of this parameter is false.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
[ balbi@ti.com : slight change to commit log
fixed one coding style issue ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SuperSpeed USB has defined a new descriptor, called
the Binary Device Object Store (BOS) Descriptor. It
has also changed a bit the definition of SET_FEATURE
and GET_STATUS requests to add USB3-specific details.
This patch implements both changes to the Composite
Gadget Framework.
[ balbi@ti.com : slight changes to commit log
fixed a compile error on ARM ]
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1471) deprecates the File-backed Storage Driver and
schedules its replacement for the 3.8 kernel release (about two years
from now). Users are advised to switch to the Mass Storage Gadget
instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1468) changes the Kconfig definition for
USB_GADGET_DUALSPEED. This option is determined entirely by which
device controller drivers are to be built, through Select statements;
it does not need to be (and should not be) configurable by the user.
Also, the "default n" line is superfluous -- everything defaults to N.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is based on the last release from PLX:
http://www.plxtech.com/files/products/net2000/software/selectiontool/RE061204-net2272-linux2.6.18.tgz
I've managed to contact them and they've confirmed that this driver was
wholly written by PLX (Seth Levy). While they have no problem with it
being merged (and they've already licensed it as GPL), they don't have
any interest in doing so themselves as this is an old part for them.
ADI has long had an add-on card which has this part on it, so we've been
keeping it up-to-date out of tree. But now that PLX has confirmed the
source of the driver, we can can take the next step of cleaning it up and
getting it merged.
So here we are! I've done quite a large clean up of the driver and
attempted to address all the common issues. Hopefully in the process,
I haven't broken anything. While it seems to still work with the board
that I have access to, it is not a PCI variant. So I have not tested
any of the PCI logic myself (beyond clean compile). Perhaps someone who
actually has a card and cares can do so.
I'll try to address further feedback, but don't expect miracles. I'm
not really familiar with the part itself, just the platform glue.
Signed-off-by: Seth Levy <seth.levy@plxtech.com>
Signed-off-by: Ash Aziz <ash.aziz@plxtech.com>
Signed-off-by: Roy Huang <roy.huang@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Samsung's S3C2416, S3C2443 and S3C2450 includes a USB High-Speed
device controller module. This driver enables support for USB high-speed
gadget functionality for the Samsung S3C24xx SoC's that include this
controller.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Alexander Neumann <alexander@bumpern.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is used across all MSM SoCs. Hence give a generic name.
All Functions and strutures are also using "msm_otg" as prefix.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed to resolve some merge conflicts that were found
in the USB host controller patches, and reported by Stephen Rothwell.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the below compilation errors.
CC drivers/usb/gadget/ci13xxx_msm.o
CC net/mac80211/led.o
drivers/usb/gadget/ci13xxx_msm.c: In function 'ci13xxx_msm_notify_event':
drivers/usb/gadget/ci13xxx_msm.c:42: error: 'USB_AHBBURST' undeclared (first use in this function)
drivers/usb/gadget/ci13xxx_msm.c:42: error: (Each undeclared identifier is reported only once
drivers/usb/gadget/ci13xxx_msm.c:42: error: for each function it appears in.)
drivers/usb/gadget/ci13xxx_msm.c:43: error: 'USB_AHBMODE' undeclared (first use in this function)
make[4]: *** [drivers/usb/gadget/ci13xxx_msm.o] Error 1
make[3]: *** [drivers/usb/gadget] Error 2
MSM USB driver is not supported on boards like trout (MSM7201) which
has an external PHY.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
lh7a40x has only been receiving updates for updates to generic code.
The last involvement from the maintainer according to the git logs was
in 2006. As such, it is a maintainence burden with no benefit.
This gets rid of two defconfigs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support new device OKI SEMICONDUCTOR's ML7213 IOH(Input/Output Hub) which is for
IVI(In-Vehicle Infotainment) use.
The ML7213 is companion chip for Intel Atom E6xx series.
The ML7213 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
This patches makes possible to use composite framework and f_ncm
NCM function driver to build a standalone NCM gadget device.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MSM SoC has chipidea USB controller. So use ci13xxx_udc core.
This driver depends on transceiver driver for clock control,
PHY initialization, VBUS detection. Register for notify_event
callback to perform MSM specific quirks after controller is reset
and stopped.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move PCI bus code from ci13xxx_udc to a new file ci13xxx_pci. SoC's
which has MIPS USB core can include the ci13xxx_udc and keep bus glue
code in their respective gadget controller drivers.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch add USB client support Marvell PXA9xx/PXA168 chips. The USB
controller in PXA9xx/PXA168 is a High-Speed OTG controller. The available
endpoints is different between PXA9xx and PXA168.
NOTE:
It is the first version of Marvell PXA9xx/PXA168 USB controller driver.
The support for OTG mode will be added in later patch.
PXA9xx and PXA168 has integrated UTMI PHY in the chips. The initialization
for the PHY is a little different between PXA9xx and PXA168.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the USB device driver of EG20T(Topcliff) PCH.
EG20T PCH is the platform controller hub that is going to be used in
Intel's upcoming general embedded platform. All IO peripherals in
EG20T PCH are actually devices sitting on AMBA bus.
EG20T PCH has USB device I/F. Using this I/F, it is able to access system
devices connected to USB device.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Acked-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 126512e3f2 added support for FSL's USB
controller on powerpc. In this commit the Open Firmware code was selected
and compiled unconditionally.
This breaks on ARM systems from FSL which use the same driver (.i.e. the i.MX
series), because ARM don't have OF support (yet). This patch fixes the problem
by only selecting the OF code on systems with Open Firmware support.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Compile-Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
warning: (USB_MUSB_HDRC_HCD && USB_SUPPORT && USB_MUSB_HDRC &&
(USB_MUSB_HOST || USB_MUSB_OTG) && USB_GADGET_MUSB_HDRC || USB_MUSB_OTG
&& <choice> && USB && USB_GADGET && PM && EXPERIMENTAL) selects USB_OTG
which has unmet direct dependencies (USB_GADGET_OMAP && ARCH_OMAP_OTG &&
USB_OHCI_HCD)
This doesn't seem to happen on 2.6.36-rc8, but still doesn't make sense
to keep this duplicated config that is already defined in usb/core.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace FSL USB platform code by simple platform driver for
creation of FSL USB platform devices.
The driver creates platform devices based on the information
from USB nodes in the flat device tree. This is the replacement
for old arch fsl_soc usb code removed by this patch. The driver
uses usual of-style binding, available EHCI-HCD and UDC
drivers can be bound to the created devices. The new of-style
driver additionaly instantiates USB OTG platform device, as the
appropriate USB OTG driver will be added soon.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's spelled "Function Filesystem" / "FunctionFS". This patch
fixes some typos (FunctioFS->FunctionFS, Funcion->Function,
funcion->function, redundant "as") in the Kconfig description of
USB_FUNCTIONFS*.
Signed-off-by: Michael Prokop <mika@grml.org>
Acked-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch that implements an USB EHCI Debug Device using the
Gadget API. This patch applies to a 2.6.35-rc3 kernel.
The gadget needs a compliant usb controller that forwards the
USB_DEVICE_DEBUG_MODE feature to its gadget.
The gadget provides two configuration modes, one that only printk() the
received data, and one that exposes a serial device to userland
(/dev/ttyGSxxx).
The gadget has been tested on an IGEPv2 board running a 2.6.35-rc1
kernel. The debug port was fed on the host side by a 2.6.34 kernel.
Signed-off-by: Stephane Duverger <stephane.duverger@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit cleans the g_fs gadget hopefully making it more
readable. This is achieved by usage of the usb_string_ids_tab()
function for batch string IDs registration as well as
generalising configuration so that a single routine is
used to add each configuration and bind interfaces. As an
effect, the code is shorter and has fewer #ifdefs.
Moreover, in some circumstances previous code #defined
CONFIG_USB_FUNCTIONFS_GENERIC macro to prevent a situation
where gadget with no configurations is built. This code removes
the #define form source code and achieves the same effect using
select in Kconfig.
This patch also changes wording and names of the Kconfig options.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Multifunction Composite Gadget have been cleaned up
and refactored so hopefully it looks prettier and works
at least as good as before changes.
A Kconfig has also been fixed to make it impossible to build
FunctionFS gadget with no configurations. With this patch, if
RNDIS is not chosen by the user CDC is force-selected.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The s3c_hsotg driver sets usb_gadget->is_dualspeed to 1, yet it doesn't define
USB_GADGET_DUALSPEED in Kconfig. This triggers a NULL pointer dereference in
the composite driver (which is fixed in another patch).
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Function Filesystem (FunctioFS) lets one create USB
composite functions in user space in the same way as GadgetFS
lets one create USB gadgets in user space. This allows
creation of composite gadgets such that some of the functions
are implemented in kernel space (for instance Ethernet, serial
or mass storage) and other are implemented in user space.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This webcam gadget instantiates a UVC camera (360p and 720p resolutions
in YUYV and MJPEG).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
g_hid is a USB gadget driver implementing the Human Interface Device class
specification. The driver handles basic HID protocol handling in the
kernel, and allows userspace to read/write HID reports trough /dev/hidgX
character devices.
Signed-off-by: Fabien Chouteau <fabien.chouteau@barco.com>
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Kconfig help message for Mass Storage Gadget claimed the
module will be named "g_file_storage" whereas it should be
"g_mass_storage".
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
g_nokia is the gadget driver implementing
WMCDC Wireless Handset Control Model for the N900
device.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB_G_MULTI uses block and net interface functions, so make it
depend on both of those. Otherwise there are lots of build errors.
Fix USB_G_MULTI config help text typos and copy/paste error.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Multifunction Composite Gadget has two configurations
consisting of Ethernet (RNDIS in first and CDC Ethernet in
second configuration), CDC Serial and File-backed Storage
functions.
When connected to a Windows host, the first configuration
is chosen thus gadget provides RNDIS Ethernet, serial and
mass storage whereas when connected to Linux host, second
configuration is chosen thus providing CDC Ethernet,
serial and mass storage.
Which configurations are built can be configured via
KConfig options.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The f_mass_storage.c has been changed into a composite function.
mass_storage.c file has been introduced which defines a
g_mass_storage gadget based on composite framework.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/built-in.o: In function `pxa25x_udc_probe':
drivers/usb/gadget/pxa25x_udc.c:2195: undefined reference to `otg_get_transceiver'
drivers/usb/gadget/pxa25x_udc.c:2300: undefined reference to `otg_put_transceiver'
pxa25x_udc.c unconditionally uses these two functions, so we need to
ensure that the object providing them is also built.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a CDC EEM ethernet gadget driver. CDC EEM is a newer
USB ethernet specification that uses a simpler interface than the older
CDC ECM. This makes CDC EEM usable by a wider set of USB hardware.
By default the ethernet gadget will still use CDC ECM/Subset, but kernel
configuration and/or a module parameter will allow alternative use of
the CDC EEM protocol.
Changes since last version:
- Brought in missing RNDIS changes that caused compile error
- Modified 'sentinel CRC' checking to match EEM host driver
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
