No-op change, only rename.
This code was misnamed originally. It was only responsible for partial
power down and not for hibernation.
Rename core_params->hibernation to core_params->power_down,
dwc2_set_param_hibernation() to dwc2_set_param_power_down().
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Configure core in device mode to support LPM according to
programming guide.
Device will start giving valid responses for LPM tokens.
After this patch device side LPM will start working.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add lpm, lpm_clock_gating, besl, hird_threshold_en and hird_threshold
core parameters. These will indicate LPM and LPM Errata support
as well as chosen L1 sleeping mode for the core and PHY.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Backup PCGCCTL1 register when entering hibernation mode and
restore it after exiting from hibernation, to keep active ACG
feature.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added function for supporting Active Clock Gating functionality
in the driver.
PCGCCTL1 (Power and Clock Control) register will be used
for controlling the core`s active clock gating feature, and
the previously reserved 12th bit in GHWCFG4 now indicates that the
controller supports the Dynamic Power Reduction (Active Clock Gating)
during no traffic scenarios such as L0, idle, resume and suspend
states.
dwc2_enable_acg() function sets GATEEN bit in PCGCCTL1 register
and enables ACG, if it supported.
According to ACG functional specification, enabling of ACG feature
in host mode done in host initialization, before turning Vbus on,
specifically in dwc2_core_host_init function.
Enabling of ACG feature in device mode done in device initialization,
before clearing the SftDiscon bit in DCTL.
This bit was cleared in dwc2_hsotg_core_connect() function.So
dwc2_enable_acg() called before dwc2_core_connect() calls.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The maximum value that unsigned char can hold is 255, meanwhile
the maximum value of interval is 2^(bIntervalMax-1)=2^15.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Deleted dwc2_hcd_dump_frrem() function, because it used undefined
parameters from dwc2_hsotg structure. The function body was in #ifdef
statement and was never compiled.
Also removed that parameters from dwc2_hsotg structure, which were
used only in dwc2_hcd_dump_frrem() function.
And also delete dwc2_sample_frrem macro, because without
dwc2_hcd_dump_frrem() function it's lose its purpose.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Changed AHB burst size from INCR4 to INCR by default.
With this value driver shows excellent DMA performance.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move dwc2_hsotg_wait_bit_set function to core.c so it can be used
anywhere in the code.
Added dwc2_hsotg_wait_bit_clear function in core.c.
Replace all the parts of register bit polling code with
dwc2_hsotg_wait_bit_set or dwc2_hsotg_wait_bit_clear functions
calls depends on code logic.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Only check the ID portion of the GSNPSID register and don’t check
the version. This will allow the driver to work with version 4.00a
and later of the DWC_hsotg IP.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The irq is available in hsotg already, so there's no need to pass it as
separate function parameter.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Not many changes here, the most important being an improvement for TI's
AM57xx and DRA7xx devices which allows them to disable a metastability
workaround in situations where we know what's going on.
Other than that, we have a set of changes on Renesas UDC to make the
code a little easier to read and maintain while also better supporting
extcon framework.
The u_serial adaptation layer learned to use kfifo instead of cooking
its own FIFO implementation.
DWC3 learned to decode a few more USB requests on the trace output.
-----BEGIN PGP SIGNATURE-----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=uwh/
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.16 merge window
Not many changes here, the most important being an improvement for TI's
AM57xx and DRA7xx devices which allows them to disable a metastability
workaround in situations where we know what's going on.
Other than that, we have a set of changes on Renesas UDC to make the
code a little easier to read and maintain while also better supporting
extcon framework.
The u_serial adaptation layer learned to use kfifo instead of cooking
its own FIFO implementation.
DWC3 learned to decode a few more USB requests on the trace output.
On rk3288-veyron devices on Chrome OS it was found that plugging in an
Arduino-based USB device could cause the system to lockup, especially
if the CPU Frequency was at one of the slower operating points (like
100 MHz / 200 MHz).
Upon tracing, I found that the following was happening:
* The USB device (full speed) was connected to a high speed hub and
then to the rk3288. Thus, we were dealing with split transactions,
which is all handled in software on dwc2.
* Userspace was initiating a BULK IN transfer
* When we sent the SSPLIT (to start the split transaction), we got an
ACK. Good. Then we issued the CSPLIT.
* When we sent the CSPLIT, we got back a NAK. We immediately (from
the interrupt handler) started to retry and sent another SSPLIT.
* The device kept NAKing our CSPLIT, so we kept ping-ponging between
sending a SSPLIT and a CSPLIT, each time sending from the interrupt
handler.
* The handling of the interrupts was (because of the low CPU speed and
the inefficiency of the dwc2 interrupt handler) was actually taking
_longer_ than it took the other side to send the ACK/NAK. Thus we
were _always_ in the USB interrupt routine.
* The fact that USB interrupts were always going off was preventing
other things from happening in the system. This included preventing
the system from being able to transition to a higher CPU frequency.
As I understand it, there is no requirement to retry super quickly
after a NAK, we just have to retry sometime in the future. Thus one
solution to the above is to just add a delay between getting a NAK and
retrying the transmission. If this delay is sufficiently long to get
out of the interrupt routine then the rest of the system will be able
to make forward progress. Even a 25 us delay would probably be
enough, but we'll be extra conservative and try to delay 1 ms (the
exact amount depends on HZ and the accuracy of the jiffy and how close
the current jiffy is to ticking, but could be as much as 20 ms or as
little as 1 ms).
Presumably adding a delay like this could impact the USB throughput,
so we only add the delay with repeated NAKs.
NOTE: Upon further testing of a pl2303 serial adapter, I found that
this fix may help with problems there. Specifically I found that the
pl2303 serial adapters tend to respond with a NAK when they have
nothing to say and thus we end with this same sequence.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dwc2 USB controller in Stratix10 has an additional ECC reset bit that
needs to get de-asserted in order for the controller to work properly.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In host mode reading from DPTXSIZn returning invalid value in
dwc2_check_param_tx_fifo_sizes function.
In total TxFIFO size calculations unnecessarily reducing by ep_info.
hw->total_fifo_size can be fully allocated for FIFO's.
Added num_dev_in_eps member in dwc2_hw_params structure to save number
of IN EPs.
Added g_tx_fifo_size array in dwc2_hw_params structure to store power
on reset values of DPTXSIZn registers in forced device mode.
Updated dwc2_hsotg_tx_fifo_count() function to get TxFIFO count from
num_dev_in_eps.
Updated dwc2_get_dev_hwparams() function to store DPTXFSIZn in
g_tx_fifo_size array.
dwc2_get_host/dev_hwparams() functions call moved after num_dev_in_eps
set from hwcfg4.
Modified dwc2_check_param_tx_fifo_sizes() function to check TxFIFOn
sizes based on g_tx_fifo_size array.
Removed ep_info subtraction during calculation of tx_addr_max in
dwc2_hsotg_tx_fifo_total_depth() function. Also removed
dwc2_hsotg_ep_info_size() function as no more need.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the case where an external VBUS is used, we should enable the external
VBUS comparator in the driver. This would prevent an unnecessary
overcurrent error which would then disable the host port.
This patch uses the standard 'disable-over-current' binding to allow of the
option of disabling the over-current condition.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch introduces a new parameter to activate USB OTG HS/FS core
embedded phy transceiver. The STM32F4x9 SoC uses the GGPIO register
to enable the transceiver.
Also add the dwc2_set_params function for stm32f4 otg fs.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The irq is available in hsotg already, so there's no need to
pass it as separate function parameter.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Remove legacy DWC2_G_P_LEGACY_TX_FIFO_SIZE array for TX FIFOs.
Update dwc2_set_param_tx_fifo_sizes function to calculate
and assign default average FIFO depth to each member of
g_tx_fifo_size array. Total FIFO size, EP Info block's size,
FIFO operation mode and device operation mode are taken into
consideration during the calculation.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
GDFIFOCFG is available from IP version 2.91a. Fix the code to reflect
this.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Hi6220's usb controller is limited in that it does not
support "Split Transactions", so it does not support communicating
with low-speed and full-speed devices behind a high-speed hub.
Thus it requires a quirk so that we can manually drop the usb
speed when low/full-speed are attached, and bump back to high
speed when they are removed.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Chen Yu <chenyu56@huawei.com>
[jstultz: Reworked to simplify the patch, and made
commit log to be more specific about the issue]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Basically when plugging in various cables in different orders, I'm
occasionally seeing the following BUG splat:
[ 86.215403] BUG: scheduling while atomic: kworker/u16:2/53/0x00000002
[ 86.219164] usb 1-1: USB disconnect, device number 9
[ 86.226845] Preemption disabled at:[ 86.230218]
[<ffffff8008673558>] dwc2_conn_id_status_change+0x120/0x250
[ 86.236894] CPU: 0 PID: 53 Comm: kworker/u16:2 Tainted: G W
4.9.0-rc8-00051-gd5a7979-dirty #1702
[ 86.246836] Hardware name: HiKey Development Board (DT)
[ 86.252100] Workqueue: dwc2 dwc2_conn_id_status_change
[ 86.257279] Call trace:
[ 86.259771] [<ffffff8008087c28>] dump_backtrace+0x0/0x1a0
[ 86.265210] [<ffffff8008087ddc>] show_stack+0x14/0x20
[ 86.270308] [<ffffff80084343f0>] dump_stack+0x90/0xb0
[ 86.275401] [<ffffff80080d8d94>] __schedule_bug+0x6c/0xb8
[ 86.280841] [<ffffff8008a07220>] __schedule+0x4f8/0x5b0
[ 86.286099] [<ffffff8008a073e8>] schedule+0x38/0xa0
[ 86.291017] [<ffffff8008a0a6cc>] schedule_hrtimeout_range_clock+0x8c/0xf0
[ 86.297846] [<ffffff8008a0a740>] schedule_hrtimeout_range+0x10/0x18
[ 86.304150] [<ffffff8008a0a4a0>] usleep_range+0x50/0x58
[ 86.309418] [<ffffff800866d8dc>] dwc2_wait_for_mode.isra.4+0x54/0xd0
[ 86.315815] [<ffffff800866f058>] dwc2_core_reset+0xe0/0x168
[ 86.321431] [<ffffff800867e364>] dwc2_hsotg_core_init_disconnected+0x2c/0x310
[ 86.328602] [<ffffff8008673568>] dwc2_conn_id_status_change+0x130/0x250
[ 86.335254] [<ffffff80080ccd48>] process_one_work+0x118/0x370
[ 86.341035] [<ffffff80080ccfe8>] worker_thread+0x48/0x498
[ 86.346473] [<ffffff80080d2eb0>] kthread+0xd0/0xe8
[ 86.351299] [<ffffff8008082e80>] ret_from_fork+0x10/0x50
This seems to be caused by the dwc2_wait_for_mode() calling
usleep_range() while the hstog->lock spinlock is held, since
we take that before calling dwc2_hsotg_core_init_disconnected().
This patch avoids the issue by adding an extra argument to
dwc2_core_reset(), as suggested by John Youn, which allows us to
skip the waiting, which should be unnecessary when calling from
dwc2_hsotg_core_init_disconnected().
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check these parameters only for true or false. There is no need to check
for greater or less than 0.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Group the members by global, host, and gadget params. Formatting and
organizational change only.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Update the param types to appropriately sized ints and bools.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Initialize the core parameters to their default, auto-detected values.
Remove all the previous dwc2_set_param* methods. Most of what this code
is doing is handling defaults for "not set" values and other trivial
checks. The checking can be simplified and will be done in a later
commit.
This allows us to change only those parameters that won't work with
default settings. It also allows us to use non-int parameters.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The otg_ver parameter only controls the SRP pulsing method and defaults
to the 1.3 behavior. It is unused and can be removed.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix misaligned and over 80-character comments.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This commmit is the result of running checkpatch --fix.
The results were verified for correctness. Some of the fixes result in
line over 80 char which we will fix manually later.
The following is a summary of what was done by checkpatch:
* Remove externs on function prototypes.
* Replace symbolic permissions with octal.
* Align code to open parens.
* Replace 'unsigned' with 'unsigned int'.
* Remove unneccessary blank lines.
* Add blank lines after declarations.
* Add spaces around operators.
* Remove unnecessary spaces after casts.
* Replace 'x == NULL' with '!x'.
* Replace kzalloc() with kcalloc().
* Concatenate multi-line strings.
* Use the BIT() macro.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 05ee799f20 ("usb: dwc2: Move gadget settings into core_params")
changes to type u16 for DT binding "g-rx-fifo-size" and
"g-np-tx-fifo-size" but use type u32 for "g-tx-fifo-size". Finally the
the first two parameters cannot be passed successfully with wrong data
format. This is found the data transferring broken on 96boards Hikey.
This patch is to change all parameters to u32 type, and verified on
Hikey board the DT parameters can pass successfully.
[johnyoun: minor rebase]
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added new core param for low speed, which can be used only when SNPSID
is equal to DWC2_CORE_FS_IOT. When LS mode is enabled, we are
restricting ep types and providing to upper layer only INTR and CTRL
endpoints.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add new device IDs for IOT gadget. Done changes in probe to
configure core accordingly depending on device ID value.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Preparing for isochronous transfers support adding in DDMA mode. In DDMA
isochronous transfers are handled differently compared to Slave and BDMA
modes. This is caused by fact that isoc requests contain data for one
frame/microframe. HW descriptor should contain data of one
frame/microframe as well. Hence each DMA descriptor in the chain will
correspond to one usb request.
Decided to divide endpoints descriptor chain to two halves - while one
will be processed by HW, other one will be under SW control. First part
will be passed to HW once ISOC traffic needs to be started. In parallel
to HW's work SW will keep creating new entries in the other half of
chain if new requests arrive in ep_queue routine. This will allow
passing of already pre-prepared descriptors to HW immediately after
endpoint gets disabled. The endpoint should be disabled once HW closes
descriptor with "L" bit set. Afterwards SW will switch to use first part
of chain if more requests are arriving.
Add two members to the dwc2_hsotg_ep structure to be used in isochronous
transfers' handling in DDMA mode:
-isoc_chain_num - indicates which half of EP descriptor chain can be
used by SW to add new queued requests while HW is
processing other half.
-next_desc - index which points to next not yet programmed descriptor in
the half of descriptor chain which is under SW control.
Also add initialization of these fields in function
dwc2_hsotg_ep_enable().
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add DMA descriptor members to the dwc2_hsotg_ep structure.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Update dwc2_hsotg structure to add descriptor chains for EP 0: two DMA
descriptors for Setup phase, per one for IN/OUT data and status phases.
Add their allocation function dwc2_gadget_alloc_ctrl_desc_chains() and
its call during gadget probe.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a parameter for descriptor DMA and set it based on hardware
capabilities. This won't actually be used by the gadget until later,
when the descriptor DMA code is in place.
Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is not needed as the gadget now fully supports DMA and it can
autodetect it. This was initially added because gadget DMA mode was only
partially implemented so could not be automatically enabled.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver will automatically enable host DMA and use it if available.
This is consistent with the behavior of all existing platforms.
Read in the "snps,host-dma-disable" device property to disable it.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Rename it so that it is more consistent with the gadget dma parameter.
It only affects host-mode operation so prefix it with "host".
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move the gadget devicetree settings into the core_params structure and
document them. Then set and check them in params.c, with the addition of
some helper functions, and remove the equivalent code in gadget.c.
Because these parameters came from the standalone s3c driver, they have
a fixed default value rather than an autodetected one. Preserve and
document this behavior to avoid any compatibility issues.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This hardware parameter is not host specific. It also applies to device
mode. Drop the "host" from the name to make that clear.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Remove the unnecessary prototypes for all the parameter setting
functions and declare those functions 'static' in the params.c file.
Also remove the duplicate documentation that went along with them. They
are already documented as part of the params structure definition.
Then move the constants that went along with the prototype into the
structure.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Replace this by statically defining a function with defaults, and just
assigning it. This will allow us to use parameters of any type and any
default value.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Consolidate and move all the parameter initialization code from the
probe function to params.c.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This makes it consistent with the hw_params struct and simplifies the
memory management for future refactoring. Fix up usage in all files.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a params.c file and move all driver parameter code there, including
all the static parameter definitions.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dma_desc_fs_enable does not correspond to any hardware parameter and
is unused. Remove it.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit aa381a7259 ("usb: dwc2: gadget: fix TX FIFO size
and address initialization").
The original commit removed the FIFO size programming per endpoint. The
DPTXFSIZn register is also used for DIEPTXFn and the SIZE field is r/w
in dedicated fifo mode. So it isn't appropriate to simply remove this
initialization as it might break existing behavior.
Also, some cores might not have enough fifo space to handle the
programming method used in the reverted patch, resulting in fifo
initialization failure.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
