On OMAP2/3 McBSP1 port has 6 pin setup, while on OMAP4 the port is McBSP4.
Implement the CLKR/FSR clock mux selection for OMAP4, and make sure that
we add the correct callback for the correct port across supported OMAP
versions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The driver for omap-mcbsp-dai no longer exist since it has been merged with
the omap-mcbsp driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The OMAP McBSP driver stack used to contain two different
drivers. One of them was used as kind low-level access to
the IP, while the other driver was the ASoC DAI driver.
There were global, shared structures, in different places,
the McBSP instances are reffered with id numbers (sometimes
0 based, in other cases 1 based id numbers).
Create one single driver for OMAP McBSP with name: omap-mcbsp.
Convert the old omap-mcbsp driver initially to be a library
for the omap-mcbsp DAI driver. With this change we can get rid
of all global variables, structures.
Further cleanup is coming...
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Move most of the content of the plat/mcbsp.h header file under
sound/soc/omap/ to help further cleanups.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In order to consolidate the McBSP driver move it out from
arch/arm/plat-omap directory under sound/soc/omap/
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Convert the plat-omap/mcbsp.c driver to be proper platform driver.
Remove the omap_mcbsp_init function call which was called from
mach-omap1/2/mcbsp.c to register the platform driver for the just
created platform device in the same function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The cpu_is_omap4430() macro always return with 0. Use the correct
cpu_is_omap443x() to check for Panda revision.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
from arch/arm into sound/soc. There's also some general driver specific
tweaks and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0lYr
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into topic/asoc
A few more ASoC updates, the main one is the move of the audmux driver
from arch/arm into sound/soc. There's also some general driver specific
tweaks and fixes.
As audmux becomes a platform driver and its callers are all ASoC
machine drivers, there is no reason to keep it in arch folder, so
move it to sound/soc/imx.
One bonus point would be those ASoC machine drivers stop including
mach/audmux.h, since it's been moved to sound/soc/imx/imx-audmux.h.
This should be a move to the right direction in terms of single kernel
image goal.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It coverts audmux to a platform driver, so that it can be moved into
sound/soc/imx and adopt device tree support later.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It merges audmux-v1 and audmux-v2 under arch/arm/plat-mxc into one.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It moves phycore audmux configuration call from board file into ASoC
machine driver phycore-ac97 to ease converting audmux into a platform
driver later.
It moves phycore audmux configuration call from board file into ASoC
machine driver phycore-ac97, so that it gets aligned with wm1133-ev1
and mx27vis-aic32x4, and more importantly it will ease the moving of
audmux into sound/soc/imx as a platform driver later.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It moves eukrea audmux configuration call from board file into ASoC
machine driver eukrea-tlv320, so that it gets aligned wm1133-ev1 and
mx27vis-aic32x4, and more importantly it will ease the moving of audmux
into sound/soc/imx as a platform driver later.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
of bugfixes and driver updates there's quite a few framework enhancements.
Most are either small or are laying the groundwork for user visible
features (especially dynamic PCM), the most directly visible change is
the dmaengine library. There's also a bunch of regmap API enhancements
pulled into the tree so that either the framework or drivers can take
advantage of the new features.
Changes include:
- Support for widgets not associated with a CODEC, an important part of
the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based DMA
drivers contributed by Lars-Peter Clausen. This will save a lot of
code and make it much easier to deploy enhancements to dmaengine.
- Support for binary controls, used for providing runtime configuration
of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do without
any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much effort to
put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics WM2200.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=FpJH
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into topic/asoc
This has been a very active release for ASoC, as well as the usual raft
of bugfixes and driver updates there's quite a few framework enhancements.
Most are either small or are laying the groundwork for user visible
features (especially dynamic PCM), the most directly visible change is
the dmaengine library. There's also a bunch of regmap API enhancements
pulled into the tree so that either the framework or drivers can take
advantage of the new features.
Changes include:
- Support for widgets not associated with a CODEC, an important part of
the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based DMA
drivers contributed by Lars-Peter Clausen. This will save a lot of
code and make it much easier to deploy enhancements to dmaengine.
- Support for binary controls, used for providing runtime configuration
of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do without
any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much effort to
put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics WM2200.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPQDoTAAoJEHm+PkMAQRiGMpYH/ibfyIFBrKMD1v/s9oNvp8rS
c7J7E7mHZOylCHrpIS3lX3ZbOfOe33Ln0Z59f1/TcV4CMMz0NrKYcTC8erj/H/DA
8DRYegiczWKqiXRgktwaZXkJcwXYdOOL1WQYxuzzbZcwRrNBY2QpH7Zu8Bj+TPAy
d4fvJHWdlh4sbWVdQmLRbp04UB9J/Z5/uWmSNvVQjLLdRlD+mEBbt7JjiNY6sUVC
2sJoAs9F3UlHu7VaN+JIhMOGZ3GqOpHGBxN/aWxJ/7GsXdXuAfCrxoPxaAe4xzOa
HndN5ZDyg02Vy5uDeUzj+HJPW3M8L4Q0nwxAYb3ZnQ5tbpu1Q2cHfIBealomWCQ=
=R91X
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc4' into for-3.4 in order to resolve the conflict
resolved below within the FSI driver and allow the application of the
dmaeengine conversion that depends on this resolution.
Linux 3.3-rc4
Conflicts:
sound/soc/sh/fsi.c
The majority of them are regression fixes for stuff that broke during
the merge 3.3 window.
The notable ones are:
* The at91 ata drivers both broke because of an earlier cleanup patch that
some other patches were based on. Jean-Christophe decided to remove
the legacy at91_ide driver and fix the new-style at91-pata driver while
keeping the cleanup patch. I almost rejected the patches for being too
late and too big but in the end decided to accept them because they
fix a regression.
* A patch fixing build breakage from the sysdev-to-device conversion
colliding with other changes touches a number of mach-s3c files.
* b0654037 "ARM: orion: Fix Orion5x GPIO regression from MPP cleanup"
is a mechanical change that unfortunately touches a lot of lines
that should up in the diffstat.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=QYVn
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
These are the bug fixes that have accumulated since 3.3-rc3 in arm-soc.
The majority of them are regression fixes for stuff that broke during
the merge 3.3 window.
The notable ones are:
* The at91 ata drivers both broke because of an earlier cleanup patch that
some other patches were based on. Jean-Christophe decided to remove
the legacy at91_ide driver and fix the new-style at91-pata driver while
keeping the cleanup patch. I almost rejected the patches for being too
late and too big but in the end decided to accept them because they
fix a regression.
* A patch fixing build breakage from the sysdev-to-device conversion
colliding with other changes touches a number of mach-s3c files.
* b0654037 "ARM: orion: Fix Orion5x GPIO regression from MPP cleanup"
is a mechanical change that unfortunately touches a lot of lines
that should up in the diffstat.
* tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
ARM: at91: drop ide driver in favor of the pata one
pata/at91: use newly introduced SMC accessors
ARM: at91: add accessor to manage SMC
ARM: at91:rtc/rtc-at91sam9: ioremap register bank
ARM: at91: USB AT91 gadget registration for module
ep93xx: fix build of vision_ep93xx.c
ARM: OMAP2xxx: PM: fix OMAP2xxx-specific UART idle bug in v3.3
ARM: orion: Fix USB phy for orion5x.
ARM: orion: Fix Orion5x GPIO regression from MPP cleanup
ARM: EXYNOS: Add cpu-offset property in gic device tree node
ARM: EXYNOS: Bring exynos4-dt up to date
ARM: OMAP3: cm-t35: fix section mismatch warning
ARM: OMAP2: Fix the OMAP2 only build break seen with 2011+ ARM tool-chains
ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
ARM: tegra: paz00: fix wrong SD1 power gpio
i2c: tegra: Add devexit_p() for remove
ARM: EXYNOS: Correct M-5MOLS sensor clock frequency on Universal C210 board
ARM: EXYNOS: Correct framebuffer window size on Nuri board
ARM: SAMSUNG: Fix missing api-change from subsys_interface change
ARM: EXYNOS: Fix "warning: initialization from incompatible pointer type"
...
Here are a few more fixes for powerpc. Some are regressions, the rest
is simple/obvious/nasty enough that I deemed it good to go now.
Here's also step one of deprecating legacy iSeries support: we are
removing it from the main defconfig.
Nobody seems to be using it anymore and the code is nasty to maintain,
(involves horrible hacks in various low level areas of the kernel) so we
plan to actually rip it out at some point. For now let's just avoid
building it by default. Stephen will proceed to do the actual removal
later (probably 3.4 or 3.5).
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/perf: power_pmu_start restores incorrect values, breaking frequency events
powerpc/adb: Use set_current_state()
powerpc: Disable interrupts early in Program Check
powerpc: Remove legacy iSeries from ppc64_defconfig
powerpc/fsl/pci: Fix PCIe fixup regression
powerpc: Fix kernel log of oops/panic instruction dump
After all the FPU state cleanups and finally finding the problem that
caused all our FPU save/restore problems, this re-introduces the
preloading of FPU state that was removed in commit b3b0870ef3 ("i387:
do not preload FPU state at task switch time").
However, instead of simply reverting the removal, this reimplements
preloading with several fixes, most notably
- properly abstracted as a true FPU state switch, rather than as
open-coded save and restore with various hacks.
In particular, implementing it as a proper FPU state switch allows us
to optimize the CR0.TS flag accesses: there is no reason to set the
TS bit only to then almost immediately clear it again. CR0 accesses
are quite slow and expensive, don't flip the bit back and forth for
no good reason.
- Make sure that the same model works for both x86-32 and x86-64, so
that there are no gratuitous differences between the two due to the
way they save and restore segment state differently due to
architectural differences that really don't matter to the FPU state.
- Avoid exposing the "preload" state to the context switch routines,
and in particular allow the concept of lazy state restore: if nothing
else has used the FPU in the meantime, and the process is still on
the same CPU, we can avoid restoring state from memory entirely, just
re-expose the state that is still in the FPU unit.
That optimized lazy restore isn't actually implemented here, but the
infrastructure is set up for it. Of course, older CPU's that use
'fnsave' to save the state cannot take advantage of this, since the
state saving also trashes the state.
In other words, there is now an actual _design_ to the FPU state saving,
rather than just random historical baggage. Hopefully it's easier to
follow as a result.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This moves the bit that indicates whether a thread has ownership of the
FPU from the TS_USEDFPU bit in thread_info->status to a word of its own
(called 'has_fpu') in task_struct->thread.has_fpu.
This fixes two independent bugs at the same time:
- changing 'thread_info->status' from the scheduler causes nasty
problems for the other users of that variable, since it is defined to
be thread-synchronous (that's what the "TS_" part of the naming was
supposed to indicate).
So perfectly valid code could (and did) do
ti->status |= TS_RESTORE_SIGMASK;
and the compiler was free to do that as separate load, or and store
instructions. Which can cause problems with preemption, since a task
switch could happen in between, and change the TS_USEDFPU bit. The
change to TS_USEDFPU would be overwritten by the final store.
In practice, this seldom happened, though, because the 'status' field
was seldom used more than once, so gcc would generally tend to
generate code that used a read-modify-write instruction and thus
happened to avoid this problem - RMW instructions are naturally low
fat and preemption-safe.
- On x86-32, the current_thread_info() pointer would, during interrupts
and softirqs, point to a *copy* of the real thread_info, because
x86-32 uses %esp to calculate the thread_info address, and thus the
separate irq (and softirq) stacks would cause these kinds of odd
thread_info copy aliases.
This is normally not a problem, since interrupts aren't supposed to
look at thread information anyway (what thread is running at
interrupt time really isn't very well-defined), but it confused the
heck out of irq_fpu_usable() and the code that tried to squirrel
away the FPU state.
(It also caused untold confusion for us poor kernel developers).
It also turns out that using 'task_struct' is actually much more natural
for most of the call sites that care about the FPU state, since they
tend to work with the task struct for other reasons anyway (ie
scheduling). And the FPU data that we are going to save/restore is
found there too.
Thanks to Arjan Van De Ven <arjan@linux.intel.com> for pointing us to
the %esp issue.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Reported-and-tested-by: Raphael Prevost <raphael@buro.asia>
Acked-and-tested-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The AMD K7/K8 CPUs don't save/restore FDP/FIP/FOP unless an exception is
pending. In order to not leak FIP state from one process to another, we
need to do a floating point load after the fxsave of the old process,
and before the fxrstor of the new FPU state. That resets the state to
the (uninteresting) kernel load, rather than some potentially sensitive
user information.
We used to do this directly after the FPU state save, but that is
actually very inconvenient, since it
(a) corrupts what is potentially perfectly good FPU state that we might
want to lazy avoid restoring later and
(b) on x86-64 it resulted in a very annoying ordering constraint, where
"__unlazy_fpu()" in the task switch needs to be delayed until after
the DS segment has been reloaded just to get the new DS value.
Coupling it to the fxrstor instead of the fxsave automatically avoids
both of these issues, and also ensures that we only do it when actually
necessary (the FP state after a save may never actually get used). It's
simply a much more natural place for the leaked state cleanup.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yes, taking the trap to re-load the FPU/MMX state is expensive, but so
is spending several days looking for a bug in the state save/restore
code. And the preload code has some rather subtle interactions with
both paravirtualization support and segment state restore, so it's not
nearly as simple as it should be.
Also, now that we no longer necessarily depend on a single bit (ie
TS_USEDFPU) for keeping track of the state of the FPU, we migth be able
to do better. If we are really switching between two processes that
keep touching the FP state, save/restore is inevitable, but in the case
of having one process that does most of the FPU usage, we may actually
be able to do much better than the preloading.
In particular, we may be able to keep track of which CPU the process ran
on last, and also per CPU keep track of which process' FP state that CPU
has. For modern CPU's that don't destroy the FPU contents on save time,
that would allow us to do a lazy restore by just re-enabling the
existing FPU state - with no restore cost at all!
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This creates three helper functions that do the TS_USEDFPU accesses, and
makes everybody that used to do it by hand use those helpers instead.
In addition, there's a couple of helper functions for the "change both
CR0.TS and TS_USEDFPU at the same time" case, and the places that do
that together have been changed to use those. That means that we have
fewer random places that open-code this situation.
The intent is partly to clarify the code without actually changing any
semantics yet (since we clearly still have some hard to reproduce bug in
this area), but also to make it much easier to use another approach
entirely to caching the CR0.TS bit for software accesses.
Right now we use a bit in the thread-info 'status' variable (this patch
does not change that), but we might want to make it a full field of its
own or even make it a per-cpu variable.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Touching TS_USEDFPU without touching CR0.TS is confusing, so don't do
it. By moving it into the callers, we always do the TS_USEDFPU next to
the CR0.TS accesses in the source code, and it's much easier to see how
the two go hand in hand.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 5b1cbac377 ("i387: make irq_fpu_usable() tests more robust")
added a sanity check to the #NM handler to verify that we never cause
the "Device Not Available" exception in kernel mode.
However, that check actually pinpointed a (fundamental) race where we do
cause that exception as part of the signal stack FPU state save/restore
code.
Because we use the floating point instructions themselves to save and
restore state directly from user mode, we cannot do that atomically with
testing the TS_USEDFPU bit: the user mode access itself may cause a page
fault, which causes a task switch, which saves and restores the FP/MMX
state from the kernel buffers.
This kind of "recursive" FP state save is fine per se, but it means that
when the signal stack save/restore gets restarted, it will now take the
'#NM' exception we originally tried to avoid. With preemption this can
happen even without the page fault - but because of the user access, we
cannot just disable preemption around the save/restore instruction.
There are various ways to solve this, including using the
"enable/disable_page_fault()" helpers to not allow page faults at all
during the sequence, and fall back to copying things by hand without the
use of the native FP state save/restore instructions.
However, the simplest thing to do is to just allow the #NM from kernel
space, but fix the race in setting and clearing CR0.TS that this all
exposed: the TS bit changes and the TS_USEDFPU bit absolutely have to be
atomic wrt scheduling, so while the actual state save/restore can be
interrupted and restarted, the act of actually clearing/setting CR0.TS
and the TS_USEDFPU bit together must not.
Instead of just adding random "preempt_disable/enable()" calls to what
is already excessively ugly code, this introduces some helper functions
that mostly mirror the "kernel_fpu_begin/end()" functionality, just for
the user state instead.
Those helper functions should probably eventually replace the other
ad-hoc CR0.TS and TS_USEDFPU tests too, but I'll need to think about it
some more: the task switching functionality in particular needs to
expose the difference between the 'prev' and 'next' threads, while the
new helper functions intentionally were written to only work with
'current'.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
perf on POWER stopped working after commit e050e3f0a7 (perf: Fix
broken interrupt rate throttling). That patch exposed a bug in
the POWER perf_events code.
Since the PMCs count upwards and take an exception when the top bit
is set, we want to write 0x80000000 - left in power_pmu_start. We were
instead programming in left which effectively disables the counter
until we eventually hit 0x80000000. This could take seconds or longer.
With the patch applied I get the expected number of samples:
SAMPLE events: 9948
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>
Program Check exceptions are the result of WARNs, BUGs, some
type of breakpoints, kprobe, and other illegal instructions.
We want interrupts (and thus preemption) to remain disabled
while doing the initial stage of testing the reason and
branching off to a debugger or kprobe, so we are still on
the original CPU which makes debugging easier in various cases.
This is how the code was intended, hence the local_irq_enable()
right in the middle of program_check_exception().
However, the assembly exception prologue for that exception was
incorrectly marked as enabling interrupts, which defeats that
(and records a redundant enable with lockdep).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since we are heading towards removing the Legacy iSeries platform, start
by no longer building it for ppc64_defconfig.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Upstream changes to the way PHB resources are registered
broke the resource fixup for FSL boards.
We can no longer rely on the resource pointer array for the PHB's
pci_bus structure, so let's leave it alone and go straight for
the PHB resources instead. This also makes the code generally
more readable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A kernel oops/panic prints an instruction dump showing several
instructions before and after the instruction which caused the
oops/panic.
The code intended that the faulting instruction be enclosed in angle
brackets, however a bug caused the faulting instruction to be
interpreted by printk() as the message log level.
To fix this, the KERN_CONT log level is added before the actual text of
the printed message.
=== Before the patch ===
[ 1081.587266] Instruction dump:
[ 1081.590236] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
[ 1081.598034] 3d20c03a 9009a114 7c0004ac 39200000
[ 1081.602500] 4e800020 3803ffd0 2b800009
<4>[ 1081.587266] Instruction dump:
<4>[ 1081.590236] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
<4>[ 1081.598034] 3d20c03a 9009a114 7c0004ac 39200000
<98090000>[ 1081.602500] 4e800020 3803ffd0 2b800009
=== After the patch ===
[ 51.385216] Instruction dump:
[ 51.388186] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
[ 51.395986] 3d20c03a 9009a114 7c0004ac 39200000 <98090000> 4e800020 3803ffd0 2b800009
<4>[ 51.385216] Instruction dump:
<4>[ 51.388186] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
<4>[ 51.395986] 3d20c03a 9009a114 7c0004ac 39200000 <98090000> 4e800020 3803ffd0 2b800009
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The check for save_init_fpu() (introduced in commit 5b1cbac377: "i387:
make irq_fpu_usable() tests more robust") was the wrong way around, but
I hadn't noticed, because my "tests" were bogus: the FPU exceptions are
disabled by default, so even doing a divide by zero never actually
triggers this code at all unless you do extra work to enable them.
So if anybody did enable them, they'd get one spurious warning.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Quoth BenH:
"Here are a few powerpc fixes for 3.3, all pretty trivial. I also
added the patch to define GET_IP/SET_IP so we can use some more
asm-generic goodness."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pseries/eeh: Fix crash when error happens during device probe
powerpc/pseries: Fix partition migration hang in stop_topology_update
powerpc/powernv: Disable interrupts while taking phb->lock
powerpc: Fix WARN_ON in decrementer_check_overflow
powerpc/wsp: Fix IRQ affinity setting
powerpc: Implement GET_IP/SET_IP
powerpc/wsp: Permanently enable PCI class code workaround
by the xen-pci[front|back] to conform to the one used in majority of
PCI drivers; Two fixes to make the code more resilient to invalid
configurations.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPOeReAAoJEFjIrFwIi8fJn9QIANP48kzrGg0uO4bjSf2h/z7G
pp3ISdtVLk7pwMov2POBqskoXSq8E0yQAfNN8se183wqNXo3Dm4rU1DIG7HQFBk9
sdcyfHI8x7pat9JClRhGxpQ23Ig9f1iWkShweCcZCO782vfxZyNd65i6t87X7uLq
7SPtG1XH2RixTX7tHtKKBqdzZ0OMXOEkJ33dgCmyrn+wzohbKrFj5mg+NdOgmzEo
VgsHPVtuq7orDROe+F9d91eAg0TILQ13th8xfWZ59lQATXu/zAlaueYt87tpy1pb
oVQvumsn8Xev+7hct9My9Tw45D4m8YOSFLG2HcekkW2WtNmGhTTbIyMh9PsLugk=
=NDYK
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-fixes-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Two fixes for VCPU offlining; One to fix the string format exposed
by the xen-pci[front|back] to conform to the one used in majority of
PCI drivers; Two fixes to make the code more resilient to invalid
configurations.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* tag 'stable/for-linus-fixes-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus_dev: add missing error check to watch handling
xen/pci[front|back]: Use %d instead of %1x for displaying PCI devfn.
xen pvhvm: do not remap pirqs onto evtchns if !xen_have_vector_callback
xen/smp: Fix CPU online/offline bug triggering a BUG: scheduling while atomic.
xen/bootup: During bootup suppress XENBUS: Unable to read cpu state
EEH may happen during a PCI driver probe. If the driver is trying to
access some register in a loop, the EEH code will try to print the
driver name. But the driver pointer in struct pci_dev is not set until
probe returns successfully.
Use a function to test if the device and the driver pointer is NULL
before accessing the driver's name.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to disable interrupts when taking the phb->lock. Otherwise
we could deadlock with pci_lock taken from an interrupt.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We use __get_cpu_var() which triggers a false positive warning
in smp_processor_id() thinking interrupts are enabled (at this
point, they are soft-enabled but hard-disabled).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We call the cache_hwirq_map() function with a linux IRQ number
but it expects a HW irq number. This triggers a BUG on multic-chip
setups in addition to not doing the right thing.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With this change, helpers such as instruction_pointer() et al, get defined
in the generic header in terms of GET_IP
Removed the unnecessary definition of profile_pc in !CONFIG_SMP case as
suggested by Mike Frysinger.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It appears that on the Chroma card, the class code of the root
complex is still wrong even on DD2 or later chips. This could
be a firmware issue, but that breaks resource allocation so let's
unconditionally fix it up.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: drop ide driver in favor of the pata one
pata/at91: use newly introduced SMC accessors
ARM: at91: add accessor to manage SMC
ARM: at91:rtc/rtc-at91sam9: ioremap register bank
ARM: at91: USB AT91 gadget registration for module
This set of changes are fixing various section mismatch warnings which
look to be completely valid. Primerily, those which are fixed are those
which can cause oopses by manipulation of driver binding via sysfs. For
example: calling code marked __init from driver probe __devinit
functions.
Some of these changes will be reworked at the next merge window when the
underlying reasons are sorted out. In the mean time, I think it's
important to have this fixed for correctness.
Also included in this set are fixes to various error messages in OMAP -
including making them gramatically correct, fixing a few spelling
errors, and more importantly, making them greppable by unwrapping them.
Tony Lindgren has acked all these patches, put them out for testing a
week ago, and I've tested them on the platforms I have.
* 'omap-fixes-warnings' of git://git.linaro.org/people/rmk/linux-arm:
ARM: omap: resolve nebulous 'Error setting wl12xx data'
ARM: omap: fix wrapped error messages in omap_hwmod.c
ARM: omap: fix section mismatch warnings in mux.c caused by hsmmc.c
ARM: omap: fix section mismatch warning for sdp3430_twl_gpio_setup()
ARM: omap: fix section mismatch error for omap_4430sdp_display_init()
ARM: omap: fix section mismatch warning for omap_secondary_startup()
ARM: omap: preemptively fix section mismatch in omap4_sdp4430_wifi_mux_init()
ARM: omap: fix section mismatch warning in mux.c
ARM: omap: fix section mismatch errors in TWL PMIC driver
ARM: omap: fix uninformative vc/i2c configuration error message
ARM: omap: fix vc.c PMIC error message
ARM: omap: fix prm44xx.c OMAP44XX_IRQ_PRCM build error
This pull request covers the major oopsing issues with OMAP, caused by
the lack of the TWL driver. Even when the TWL driver is not built in,
we shouldn't oops.
* 'omap-fixes-urgent' of git://git.linaro.org/people/rmk/linux-arm:
ARM: omap: fix broken twl-core dependencies and ifdefs
ARM: omap: fix oops in drivers/video/omap2/dss/dpi.c
ARM: omap: fix oops in arch/arm/mach-omap2/vp.c when pmic is not found
Some code - especially the crypto layer - wants to use the x86
FP/MMX/AVX register set in what may be interrupt (typically softirq)
context.
That *can* be ok, but the tests for when it was ok were somewhat
suspect. We cannot touch the thread-specific status bits either, so
we'd better check that we're not going to try to save FP state or
anything like that.
Now, it may be that the TS bit is always cleared *before* we set the
USEDFPU bit (and only set when we had already cleared the USEDFP
before), so the TS bit test may actually have been sufficient, but it
certainly was not obviously so.
So this explicitly verifies that we will not touch the TS_USEDFPU bit,
and adds a few related sanity-checks. Because it seems that somehow
AES-NI is corrupting user FP state. The cause is not clear, and this
patch doesn't fix it, but while debugging it I really wanted the code to
be more obviously correct and robust.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It was marked asmlinkage for some really old and stale legacy reasons.
Fix that and the equally stale comment.
Noticed when debugging the irq_fpu_usable() bugs.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver at91_ide is broken and should not be fixed: remove it.
Modification of device files that where making use of it. The
PATA driver (pata_at91) is able to replace at91_ide.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
SMC, Static Memory Controller will need more accessors to fine
configure its parameters.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Registration of at91_udc as a module will enable SoC
related code.
Fix following an idea from Karel Znamenacek.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Karel Znamenacek <karel@ryston.cz>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org>
It's useful to print the error code when a called function fails so a
diagnosis of why it failed is possible. In this case, it fails because
we try to register some data for the wl12xx driver, but as the driver
is not configured, a stub function is used which simply returns -ENOSYS.
Let's do the simple thing for -rc and print the error code.
Also, the return code from platform_register_device() at each of these
sites was not being checked. Add some checking, and again print the
error code.
This should be fixed properly for the next merge window so we don't
issue error messages merely because a driver is not configured.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
