Current asoc_simple_card_probe() already has dev definition,
but some place doesn't use it. Let's fix this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current asoc_simple_card_probe() already has dev definition,
but some place doesn't use it. Let's fix this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
buf was allocated by kzalloc() so it should be passed to kfree()
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When num_kcontrols is zero, widget->dobj.widget.kcontrol_type
gets set to an uninitialized local variable:
sound/soc/soc-topology.c: In function 'soc_tplg_dapm_widget_create':
sound/soc/soc-topology.c:1566:36: error: 'kcontrol_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I could not figure out which of the valid types would be appropriate
here, so this sets it to '0', which is invalid but at least well-defined
here. There is probably a better way to address the issue.
Fixes: eea3dd4f12 ("ASoC: topology: Only free TLV for volume mixers of a widget")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
The macro ZX_SPDIF_CLK_RAT should be 2 instead of 4. With this
fix, we can get correct audio output on HDMI through SPDIF interface.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ZTE ZX SPDIF and I2S drivers can work on not only ZX296702 but also
other ZTE ZX family SoCs like ZX296718, which is an arm64 platform.
Let's make a few renaming and tweak the Kconfig a bit to get the drivers
available for other ZTE ZX platforms.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver setups BRGCKR/BRRA/BRRB when .probe timing.
But it breaks sound after Suspend/Resume. These should be setups
every start timing.
This patch is tested on R-Car Gen3 Salvator-X board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver enables ADG clock when .probe timing,
but it breaks sound after Suspend/Resume. These should be setups
every suspend/resume timing too.
This patch is tested on R-Car Gen3 Salvator-X board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ssi->usrcnt will be updated on snd_soc_dai_ops::trigger,
but snd_pcm_ops::hw_params will be called *before* it.
Thus, ssi->usrcnt is still 0 when 1st call.
rsnd_ssi_hw_params() needs to check its called count, this means
trigger should be if (ssi->usrcnt) instead of if (ssi->usrcnt > 1).
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We accidentally introduced a dereference before the NULL check in
xmit_descs() as part of silencing a GCC warning.
Fixes: 16f46050e7 ("dbri: Fix compiler warning")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates FE channel constraints & BE fixup to support
quad channel DMIC capture.
DMIC pin's BE fixup is configured based on channel input, i.e.
either stereo or quad.
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This bit will enable 4th order SINC filter.
=1, filter will enable; but it consumes higher power.
=0, the sinc filter is disable, and it should always keep 0 value to
get high THD.
Therefor, disable the filter when codec initiation for better
performance when recording.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The logic of "value = ~CS35L34_MCLK_DIV & CS35L34_MCLK_RATE_XXXXXX;" is
unnecessary complex. By setting CS35L34_MCLK_DIV | CS35L34_MCLK_RATE_MASK
as the mask for regmap_update_bits() call, what the code does is exactly
the same as setting value = CS35L34_MCLK_RATE_XXXXXX.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the boot of the SST FW the firmware version is send back
to the driver. This patch is saving the FW version inside the
driver.
Signed-off-by: Sebastien Guiriec <sebastien.guiriec@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch is adding a sysfs entry in order to be able to get
access to SST FW version.
Signed-off-by: Sebastien Guiriec <sebastien.guiriec@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using regmap_update_bits(..., mask, 1) with 'mask' following (1 << k)
and k greater than 0 is wrong. Indeed, _regmap_update_bits will perform
(mask & 1), which results in 0 if LSB of mask is 0. Thus the call
regmap_update_bits(..., mask, 1) is in reality equivalent to
regmap_update_bits(..., mask, 0).
In such a case, the correct use is regmap_update_bits(..., mask, mask).
This driver is performing such a mistake with the CS42L56_AIN*_REF_MASK
masks, which equal 0x10, 0x20, 0x40 and 0x80. Fix the driver to make it
consistent with the API. Please note that this change is untested,
as I do not have this piece of hardware. Testers are welcome!
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch will check the type of embedded controls for a widget, and
only free the TLV of volume mixers. Bytes controls don't have TLV.
Just free the private value which is used as struct soc_mixer_control
for volume mixers or soc_bytes_ext for bytes controls. No need to cast
to these types before freeing it.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch can create multiple enumerated mixer controls for a widget.
Previously topology kernel driver assumes a widget can have only one
emumerated mixer control. We need to remove this restriction for Broxton.
Its firmware modules (widgets) may need multiple enum controls based on
the channel and MIC combination.
No ABI change is needed. The ABI allows a widget to embed multiple
controls.
Reported-by: G Kranthi <gudishax.kranthikumar@intel.com>
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple_card_utils was created as simple_card_core in 1st prototype,
and current code still have it. Let's tidyup
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSIU was controlled by SSI before, but
commit c7f69ab53("ASoC: rsnd: use mod base common method on SSIU")
separated it into ssiu.c
But, it didn't care about rsnd_get_dalign() for judging SSI_BUSIF_DALIGN
register value which changes the stream data order.
This function will be called from cmd/src/ssiu now, but current code
still cares ssi, not ssiu.
This patch fix it up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the sound machine driver for the TM2 and TM2E boards.
Speaker and headphone playback, Main Mic capture, Bluetooth, Voice
call and external accessory are supported.
Signed-off-by: Inha Song <ideal.song@samsung.com>
[k.kozlowski: rebased on 4.1]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
[s.nawrocki: rebased to 4.7, adjustment to the ASoC core changes,
removed unused ops and direct calls to the max98504 function,
added parsing of "audio-amplifier" and "audio-codec"
properties, added TDM API calls, switched to gpiod API]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In current ALSA SoC, Codec only has suspend/resume feature,
but it should be supported on Component level. This patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now, Card has component_dev_list, we can replace aux_comp_list
to component_dev_list with new auxiliary flags
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Card has Codec list (= codec_dev_list), but Codec will be
removed in the future. Because of this reason, this patch adds
new Component list in Card, and replace Codec list.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec on the H3 is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the H3 has no HP (headphone) and HBIAS support, and no
MIC3 input. The FIFO related registers are slightly rearranged.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec in the A23 is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the A23 does not have LINEOUT, and it does not support
headset jack detection or buttons.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of hard-coded "i2c-10EC5670:00", use the translation helper to
avoid the mismatch between i2c-codec and ACPI strings just like what
we've done for bytcr_rt5640. This gives more robust binding on funky
devices like Dell Wyse 3040.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
