When creating a new event channel with 2-level events the affinity
needs to be reset initially in order to avoid using an old affinity
from earlier usage of the event channel port. So when tearing an event
channel down reset all affinity bits.
The same applies to the affinity when onlining a vcpu: all old
affinity settings for this vcpu must be reset. As percpu events get
initialized before the percpu event channel hook is called,
resetting of the affinities happens after offlining a vcpu (this is
working, as initial percpu memory is zeroed out).
Cc: stable@vger.kernel.org
Reported-by: Julien Grall <julien@xen.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Julien Grall <jgrall@amazon.com>
Link: https://lore.kernel.org/r/20210306161833.4552-2-jgross@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
In case of error, the function dev_get_regmap() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Fixes: 9351ab8b0c ("regulator: rt4831: Adds support for Richtek RT4831 DSV regulator")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210305034930.3236099-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver uses the DVS registers PCA9450_REG_BUCKxOUT_DVS0 to set the
voltage for the buck regulators 1, 2 and 3. This has no effect as the
PRESET_EN bit is set by default and therefore the preset values are used
instead, which are set to 850 mV.
To fix this we clear the PRESET_EN bit at time of initialization.
Fixes: 0935ff5f1f ("regulator: pca9450: add pca9450 pmic driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210222115229.166620-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes the return value of pca9450_i2c_probe() to use the correct
error code when getting the sd-vsel GPIO fails.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210222150809.208942-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The per_pin->work might be still floating at the suspend, and this may
hit the access to the hardware at an unexpected timing. Cancel the
work properly at the suspend callback for avoiding the buggy access.
Note that the bug doesn't trigger easily in the recent kernels since
the work is queued only when the repoll count is set, and usually it's
only at the resume callback, but it's still possible to hit in
theory.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1182377
Reported-and-tested-by: Abhishek Sahu <abhsahu@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210310112809.9215-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When HD-audio bus receives unsolicited events during its system
suspend/resume (S3 and S4) phase, the controller driver may still try
to process events although the codec chips are already (or yet)
powered down. This might screw up the codec communication, resulting
in CORB/RIRB errors. Such events should be rather skipped, as the
codec chip status such as the jack status will be fully refreshed at
the system resume time.
Since we're tracking the system suspend/resume state in codec
power.power_state field, let's add the check in the common unsol event
handler entry point to filter out such events.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1182377
Tested-by: Abhishek Sahu <abhsahu@nvidia.com>
Cc: <stable@vger.kernel.org> # 183ab39eb0: ALSA: hda: Initialize power_state
Link: https://lore.kernel.org/r/20210310112809.9215-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HD-audio controller driver processes the unsolicited events via
its work asynchronously, and this might be pending when the system
goes to suspend. When a lengthy event handling like ELD byte reads is
running, this might trigger unexpected accesses among suspend/resume
procedure, typically seen with Nvidia driver that still requires the
handling via unsolicited event verbs for ELD updates.
This patch adds the flush of unsol_work to assure that pending events
are processed before going into suspend.
Buglink: https://bugzilla.suse.com/show_bug.cgi?id=1182377
Reported-and-tested-by: Abhishek Sahu <abhsahu@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210310112809.9215-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 0fdf1bb759 ("arm64: perf: Avoid PMXEV* indirection") changed
armv8pmu_read_evcntr() to return a u32 instead of u64. The result is
silent truncation of the event counter when using 64-bit counters. Given
the offending commit appears to have passed thru several folks, it seems
likely this was a bad rebase after v8.5 PMU 64-bit counters landed.
Cc: Alexandru Elisei <alexandru.elisei@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: <stable@vger.kernel.org>
Fixes: 0fdf1bb759 ("arm64: perf: Avoid PMXEV* indirection")
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/20210310004412.1450128-1-robh@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
As per ARM ARM DDI 0487G.a, when FEAT_LPA2 is implemented, ID_AA64MMFR0_EL1
might contain a range of values to describe supported translation granules
(4K and 16K pages sizes in particular) instead of just enabled or disabled
values. This changes __enable_mmu() function to handle complete acceptable
range of values (depending on whether the field is signed or unsigned) now
represented with ID_AA64MMFR0_TGRAN_SUPPORTED_[MIN..MAX] pair. While here,
also fix similar situations in EFI stub and KVM as well.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: kvmarm@lists.cs.columbia.edu
Cc: linux-efi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/1615355590-21102-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
We track if sve-ptrace encountered a failure in a variable but don't
actually use that value when we exit the program, do so.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210309190304.39169-1-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
In a system supporting MTE, the linear map must allow reading/writing
allocation tags by setting the memory type as Normal Tagged. Currently,
this is only handled for memory present at boot. Hotplugged memory uses
Normal non-Tagged memory.
Introduce pgprot_mhp() for hotplugged memory and use it in
add_memory_resource(). The arm64 code maps pgprot_mhp() to
pgprot_tagged().
Note that ZONE_DEVICE memory should not be mapped as Tagged and
therefore setting the memory type in arch_add_memory() is not feasible.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 0178dc7613 ("arm64: mte: Use Normal Tagged attributes for the linear map")
Reported-by: Patrick Daly <pdaly@codeaurora.org>
Tested-by: Patrick Daly <pdaly@codeaurora.org>
Link: https://lore.kernel.org/r/1614745263-27827-1-git-send-email-pdaly@codeaurora.org
Cc: <stable@vger.kernel.org> # 5.10.x
Cc: Will Deacon <will@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: David Hildenbrand <david@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20210309122601.5543-1-catalin.marinas@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
seqcount_init() must be a macro in order to preserve the static
variable that is used for the lockdep key. Don't then wrap it in an
inline function, which destroys that.
Luckily there aren't many users of this function, but fix it before it
becomes a problem.
Fixes: 80793c3471 ("seqlock: Introduce seqcount_latch_t")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/YEeFEbNUVkZaXDp4@hirez.programming.kicks-ass.net
Jakub reported that:
static struct net_device *rtl8139_init_board(struct pci_dev *pdev)
{
...
u64_stats_init(&tp->rx_stats.syncp);
u64_stats_init(&tp->tx_stats.syncp);
...
}
results in lockdep getting confused between the RX and TX stats lock.
This is because u64_stats_init() is an inline calling seqcount_init(),
which is a macro using a static variable to generate a lockdep class.
By wrapping that in an inline, we negate the effect of the macro and
fold the static key variable, hence the confusion.
Fix by also making u64_stats_init() a macro for the case where it
matters, leaving the other case an inline for argument validation
etc.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Debugged-by: "Ahmed S. Darwish" <a.darwish@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: "Erhard F." <erhard_f@mailbox.org>
Link: https://lkml.kernel.org/r/YEXicy6+9MksdLZh@hirez.programming.kicks-ass.net
This fixes the following sparse warning:
"sparse warnings: (new ones prefixed by >>)"
>> drivers/virt/acrn/irqfd.c:163:13: sparse: sparse: restricted __poll_t
degrades to integer
Fixes: dcf9625f2a ("virt: acrn: Use vfs_poll() instead of f_op->poll()")
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Shuo Liu <shuo.a.liu@intel.com>
Signed-off-by: Yejune Deng <yejune.deng@gmail.com>
Link: https://lore.kernel.org/r/20210310074901.7486-1-yejune.deng@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_get_child_by_name() increments the reference counter of the OF node it
managed to find. So after the code is done using the device node, the
refcount must be decremented. Add missing of_node_put() invocation then
to the dwc3_qcom_of_register_core() method, since DWC3 OF node is being
used only there.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20210212205521.14280-1-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently an application that opens a device and calls select()
on it, will hang if the decice is disconnected. It's a little
surprising that we had this bug for 15 years, but apparently
nobody ever uses select() with a printer: only write() and read(),
and those work fine. Well, you can also select() with a timeout.
The fix is modeled after devio.c. A few other drivers check the
condition first, then do not add the wait queue in case the
device is disconnected. We doubt that's completely race-free.
So, this patch adds the process first, then locks properly
and checks for the disconnect.
Reviewed-by: Zqiang <qiang.zhang@windriver.com>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210303221053.1cf3313e@suzdal.zaitcev.lan
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function devm_platform_ioremap_resource()
returns ERR_PTR() and never returns NULL. The NULL test in the
return value check should be replaced with IS_ERR().
Fixes: 188db4435a ("usb: gadget: s3c: use platform resources")
Cc: stable <stable@vger.kernel.org>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210305034927.3232386-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the datasheet, this controller has a restriction
which "set an endpoint number so that combinations of the DIR bit and
the EPNUM bits do not overlap.". However, since the udc core driver is
possible to assign a bulk pipe as an interrupt endpoint, an endpoint
number may not match the pipe number. After that, when user rebinds
another gadget driver, this driver broke the restriction because
the driver didn't clear any configuration in usb_ep_disable().
Example:
# modprobe g_ncm
Then, EP3 = pipe 3, EP4 = pipe 4, EP5 = pipe 6
# rmmod g_ncm
# modprobe g_hid
Then, EP3 = pipe 6, EP4 = pipe 7.
So, pipe 3 and pipe 6 are set as EP3.
So, clear PIPECFG register in usbhs_pipe_free().
Fixes: dfb87b8bfe ("usb: renesas_usbhs: gadget: fix re-enabling pipe without re-connecting")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1615168538-26101-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3-qcom currently enables wakeup interrupts unconditionally
when suspending, however this should not be done when wakeup is
disabled (e.g. through the sysfs attribute power/wakeup). Only
enable wakeup interrupts when device_may_wakeup() returns true.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210302103659.v2.1.I44954d9e1169f2cf5c44e6454d357c75ddfa99a2@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is missing playback stop/cleanup in case of
gadget's ->disable callback that happens on
events like USB host resetting or gadget disconnection
Fixes: 0591bc2360 ("usb: gadget: add f_uac1 variant based on a new u_audio api")
Cc: <stable@vger.kernel.org> # 4.13+
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1614599375-8803-3-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per UAC2 Audio Data Formats spec (2.3.1.1 USB Packets),
if the sampling rate is a constant, the allowable variation
of number of audio slots per virtual frame is +/- 1 audio slot.
It means that endpoint should be able to accept/send +1 audio
slot.
Previous endpoint max_packet_size calculation code
was adding sometimes +1 audio slot due to DIV_ROUND_UP
behaviour which was rounding up to closest integer.
However this doesn't work if the numbers are divisible.
It had no any impact with Linux hosts which ignore
this issue, but in case of more strict Windows it
caused rejected enumeration
Thus always add +1 audio slot to endpoint's max packet size
Fixes: 913e4a90b6 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
Cc: Peter Chen <peter.chen@freescale.com>
Cc: <stable@vger.kernel.org> #v4.3+
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1614599375-8803-2-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the string is invalid, this should return -EINVAL instead of 0.
Fixes: 73517cf49b ("usb: gadget: add RNDIS configfs options for class/subclass/protocol")
Cc: stable <stable@vger.kernel.org>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YCqZ3P53yyIg5cn7@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It enables USB Host support for sc8180x ACPI boot, both the standalone
one and the one behind URS (USB Role Switch). And they share the
the same dwc3_acpi_pdata with sdm845.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210301075745.20544-1-shawn.guo@linaro.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CDC ACM driver is false matching the Goodix Fingerprint device
against the USB_CDC_ACM_PROTO_AT_V25TER.
The Goodix Fingerprint device is a biometrics sensor that should be
handled in user-space. libfprint has some support for Goodix
fingerprint sensors, although not for this particular one. It is
possible that the vendor allocates a PID per OEM (Lenovo, Dell etc).
If this happens to be the case then more devices from the same vendor
could potentially match the ACM modem module table.
Signed-off-by: Yorick de Wid <ydewid@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210213144901.53199-1-ydewid@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 33d4ae9885.
Pierre-Louis writes:
Our SOF/audio CI shows an across-the-board regression when we try v5.12-rc1,
specifically on pause/resume tests with an interactive terminal running 'aplay
-i' commands managed by expect to simulate the user pressing the space bar to
pause/unpause. It turns out the processes are not longer killed and the audio
devices remain busy (see publicly available test results listed below).
git bisect points to commit 33d4ae9885 ("drivers:tty:pty: Fix a race
causing data loss on close"). Reverting the patch fixes the issue on all test
devices.
Further analysis with Corey Minyard points to a problem where a slave tty will
not get a SIGHUP when the master is closed.
So revert this for now:
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/00154592-c5ee-aaba-956e-b265473b53bc@linux.intel.com
Cc: Corey Minyard <cminyard@mvista.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Mark Brown <broonie@kernel.org>,
Fixes: 33d4ae9885 ("drivers:tty:pty: Fix a race causing data loss on close")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit fce3c5c1a2.
FIFO is triggered 4 intervals after receiving a byte, it's good
when we don't care about the time of reception, but are only
interested in the presence of any activity on the line.
Unfortunately, this method is not suitable for all tasks,
for example, the RS-485 protocol will not work properly,
since the state machine must track the request-response time
and after the timeout expires, a decision is made that the device
on the line is not responding.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Link: https://lore.kernel.org/r/20210217080608.31192-1-shc_work@mail.ru
Fixes: fce3c5c1a2 ("serial: max310x: rework RX interrupt handling")
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
led_set_brightness() involves scheduling a workqueue. As here the led's
brightness setting is done in context of the trigger's workqueue this is
unjustified overhead and it's more sensible to use
led_set_brightness_sync().
Fixes: fd4a641ac8 ("leds: trigger: implement a tty trigger")
Reported-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210219133307.4840-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ttyname is allocated before the mutex is taken, so it must not be
unlocked in the error path.
Fixes: fd4a641ac8 ("leds: trigger: implement a tty trigger")
Reported-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210219133307.4840-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 314fd52f01.
It turns .h files into non-stand-alone when building, which might cause
problems in the long-run.
Reported-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Cc: Muhammad Usama Anjum <musamaanjum@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code has a check to prevent read overflow but it needs another
check to prevent writing beyond the end of the ->ssid[] array.
Fixes: a2c60d42d9 ("staging: r8188eu: Add files for new driver - part 16")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/YEHymwsnHewzoam7@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "ie_len" is a value in the 1-255 range that comes from the user. We
have to cap it to ensure that it's not too large or it could lead to
memory corruption.
Fixes: 9a7fe54ddc ("staging: r8188eu: Add source files for new driver - part 1")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/YEHyQCrFZKTXyT7J@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to cap len at IW_ESSID_MAX_SIZE (32) to avoid memory corruption.
This can be controlled by the user via the ioctl.
Fixes: 5f53d8ca3d ("Staging: add rtl8192SU wireless usb driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/YEHoAWMOSZBUw91F@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pcl726 driver has an "interrupt" subdevice that supports Comedi
asynchronous commands, placing a value in the Comedi buffer for each
interrupt. The subdevice uses Comedi's 16-bit sample format but the
interrupt handler is calling `comedi_buf_write_samples()` with the
address of a 32-bit integer `&s->state`. On bigendian machines, this
will copy 2 bytes from the wrong end of the 32-bit integer. This isn't
really a problem since `s->state` will always be 0 for this subdevice,
but clean it up by using a 16-bit variable initialized to 0 to pass the
value.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-15-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ni_65xx driver has an "interrupt" subdevice that supports Comedi
asynchronous commands, placing a value in the Comedi buffer for each
interrupt. The subdevice uses Comedi's 16-bit sample format but the
interrupt handler is calling `comedi_buf_write_samples()` with the
address of a 32-bit integer `&s->state`. On bigendian machines, this
will copy 2 bytes from the wrong end of the 32-bit integer. This isn't
really a problem since `s->state` will always be 0 for this subdevice,
but clean it up by using a 16-bit variable initialized to 0 to pass the
value.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-14-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ni_6527 driver has an "interrupt" subdevice that supports Comedi
asynchronous commands, placing a value in the Comedi buffer for each
interrupt. The subdevice uses Comedi's 16-bit sample format but the
interrupt handler is calling `comedi_buf_write_samples()` with the
address of a 32-bit integer `&s->state`. On bigendian machines, this
will copy 2 bytes from the wrong end of the 32-bit integer. This isn't
really a problem since `s->state` will always be 0 for this subdevice,
but clean it up by using a 16-bit variable initialized to 0 to pass the
value.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-13-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comedi_parport driver has an "interrupt" subdevice that supports
Comedi asynchronous commands, placing a value in the Comedi buffer for
each interrupt. The subdevice uses Comedi's 16-bit sample format but
the interrupt handler is calling `comedi_buf_write_samples()` with the
address of a 32-bit integer `&s->state`. On bigendian machines, this
will copy 2 bytes from the wrong end of the 32-bit integer. This isn't
really a problem since `s->state` will always be 0 for this subdevice,
but clean it up by using a 16-bit variable initialized to 0 to pass the
value.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-12-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Amplicon PC36AT/PCI236 common driver has an "interrupt" subdevice
that supports Comedi asynchronous commands, placing a value in the
Comedi buffer for each interrupt. The subdevice uses Comedi's 16-bit
sample format but the interrupt handler is calling
`comedi_buf_write_samples()` with the address of a 32-bit integer
`&s->state`. On bigendian machines, this will copy 2 bytes from the
wrong end of the 32-bit integer. This isn't really a problem since
`s->state` will always be 0 for this subdevice, but clean it up by using
a 16-bit variable initialized to 0 to pass the value.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-11-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
parameter. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the parameter
holding the sample value to `unsigned short`.
[Note: the bug was introduced in commit edf4537bcb ("staging: comedi:
pcl818: use comedi_buf_write_samples()") but the patch applies better to
commit d615416de6 ("staging: comedi: pcl818: introduce
pcl818_ai_write_sample()").]
Fixes: d615416de6 ("staging: comedi: pcl818: introduce pcl818_ai_write_sample()")
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-10-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
Fixes: 1f44c034de ("staging: comedi: pcl711: use comedi_buf_write_samples()")
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-9-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the calls to
`comedi_buf_write_samples()` are passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
Fixes: de88924f67 ("staging: comedi: me4000: use comedi_buf_write_samples()")
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-8-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
[Note: the bug was introduced in commit 1700529b24 ("staging: comedi:
dmm32at: use comedi_buf_write_samples()") but the patch applies better
to the later (but in the same kernel release) commit 0c0eadadcb
("staging: comedi: dmm32at: introduce dmm32_ai_get_sample()").]
Fixes: 0c0eadadcb ("staging: comedi: dmm32at: introduce dmm32_ai_get_sample()")
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-7-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
Fixes: ad9eb43c93 ("staging: comedi: das800: use comedi_buf_write_samples()")
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-6-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the call to
`comedi_buf_write_samples()` is passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variable
holding the sample value to `unsigned short`.
Fixes: d1d24cb65e ("staging: comedi: das6402: read analog input samples in interrupt handler")
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-5-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The analog input subdevice supports Comedi asynchronous commands that
use Comedi's 16-bit sample format. However, the calls to
`comedi_buf_write_samples()` are passing the address of a 32-bit integer
variable. On bigendian machines, this will copy 2 bytes from the wrong
end of the 32-bit value. Fix it by changing the type of the variables
holding the sample value to `unsigned short`. The type of the `val`
parameter of `pci1710_ai_read_sample()` is changed to `unsigned short *`
accordingly. The type of the `val` variable in `pci1710_ai_insn_read()`
is also changed to `unsigned short` since its address is passed to
`pci1710_ai_read_sample()`.
Fixes: a9c3a015c1 ("staging: comedi: adv_pci1710: use comedi_buf_write_samples()")
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-4-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The digital input subdevice supports Comedi asynchronous commands that
read interrupt status information. This uses 16-bit Comedi samples (of
which only the bottom 8 bits contain status information). However, the
interrupt handler is calling `comedi_buf_write_samples()` with the
address of a 32-bit variable `unsigned int status`. On a bigendian
machine, this will copy 2 bytes from the wrong end of the variable. Fix
it by changing the type of the variable to `unsigned short`.
Fixes: a8c66b684e ("staging: comedi: addi_apci_1500: rewrite the subdevice support functions")
Cc: <stable@vger.kernel.org> #4.0+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-3-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Change-Of-State (COS) subdevice supports Comedi asynchronous
commands to read 16-bit change-of-state values. However, the interrupt
handler is calling `comedi_buf_write_samples()` with the address of a
32-bit integer `&s->state`. On bigendian architectures, it will copy 2
bytes from the wrong end of the 32-bit integer. Fix it by transferring
the value via a 16-bit integer.
Fixes: 6bb45f2b0c ("staging: comedi: addi_apci_1032: use comedi_buf_write_samples()")
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210223143055.257402-2-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The user can specify a "req->essid_len" of up to 255 but if it's
over IW_ESSID_MAX_SIZE (32) that can lead to memory corruption.
Fixes: 13a9930d15 ("staging: ks7010: add driver from Nanonote extra-repository")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/YD4fS8+HmM/Qmrw6@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
