Eanble the ADMA2 mode for freescale esdhc imx driver, tested on MX25
3DS board, MX51 BBG board and MX53 LOCO board.
This patch is only used to enable the ADMA2 for MX51/53 platforms.
MX25/35 can't support the ADMA2 mode, set BROKEN_ADMA quirk on
MX25/35 platforms.
The ADMA mode supported or not can be distinguished by bit 20 of
the Capability Register (offset 0x40) in the FSL eSDHC module.
Signed-off-by: Richard Zhu <richard.zhu@linaro.org>
Tested-and-acked-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Remove the use of irq_to_gpio() in the card detection interrupt
handler. The information is available in the board structure and
we can avoid using a function that has little meaning.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes a potential issue about PDC interrupts. For example we
have a ENDRX pending interrupt and a RXBUFF pending interrupt. We have
received the RXBUFF interrupt but the transfer is not finished (so we
didn't have time to give a new buffer to the PDC controller). Then we
will compute ENDRX interrupt and we will give a new buffer to the PDC
controller, just after we will compute the RXBUFF interrupt and give
one or two new buffers to the PDC controller but we are not sure that
the first buffer given has been filled. So in this situation we may
have "lost" one sg buffer. It's the same for transmission.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Assuming that a sg buffer size is a page size is false so use sg_dma_len.
A 4096 bytes can be required with two 2048-bytes sg buffer.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Rename atmci_start_command() to atmci_send_command() which is more
appropriate; atmci_start_command suggests we're sending a start command.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add pdc support for atmel-mci. It makes at91-mci driver useless because it
was only used for the old atmel MCI core which has pdc but no dma support.
To allow removing at91-mci, the capabilities of the MCI core are detected
at runtime -- then the driver will use pio, pdc or dma transfers.
Warning: at91rm9200 is not supported, to support it we need to use swab32
on data but I have no board to test it.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Change atmci_readl and atmci_writel macros: remove string concatenation.
We can use these macros with registers which are not prefixed by ATMCI_.
This is the case if we want to write PDC registers which are common to
several devices so they are not prefixed with ATMCI_.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Now that no driver any longer depends on the CONFIG_SOC_AU1??? symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files. Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace all occurrences of CONFIG_SOC_AU1??? with runtime feature detection.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-mmc@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2683/
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When indirect inclusion to <mach/hardware.h> via <mach/gpio.h> gets
removed, we will see the following compile error.
CC drivers/mmc/host/mxcmmc.o
drivers/mmc/host/mxcmmc.c: In function ‘mxcmci_init_card’:
drivers/mmc/host/mxcmmc.c:811:2: error: implicit declaration of function ‘cpu_is_mx3’
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will eventually allow <mach/gpio.h> to be deleted. This mirrors
LinusW's recent equivalent work on various other ARM platforms.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add runtime PM support to the MMCI primecell driver, making use of
the core primecell bus runtime PM support.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some devices connected to the MMC bus are power controlled by external
means. For instance, an SDIO device may be powered down/up by an
external gpio line.
In order to avoid toggling power from within the MMC host driver, add a
set_power callback function, which will be called by set_ios upon
powering down/up.
Signed-off-by: Ido Yariv <ido@wizery.com>
CC: Chris Ball <cjb@laptop.org>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch removes the samsung specific enum type 's3c2410_dmasrc'
and uses 'dma_data_direction' instead.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes the problem in sdhci-s3c host driver for Samsung Soc's.
During the card identification stage the mmc core driver enumerates for
the best bus width in combination with the highest available data rate.
It starts enumerating from the highest bus width (8) to lowest width (1).
In case of few MMC cards the 4-bit bus enumeration fails and tries
the 1-bit bus enumeration. When switched to 1-bit bus mode the host driver
has to clear the previous bus width setting and apply the new setting.
The current patch will clear the previous bus mode and apply the new
mode setting.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This corrects a logic error that I introduced in
"mmc: sdhi: Add write16_hook"
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are the following warnings and errorx when compiling the driver.
The patch adds the missing inclusion of linux/module.h to fix them.
drivers/mmc/host/sdhci-esdhc-imx.c:563:12: error: ‘THIS_MODULE’ undeclared here (not in a function)
[..]
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host driver can't get a hint of DDR mode through ios->ddr flag anymore.
ios->timing is currently used to inform DDR mode as a substitute.
And capability of MMC_CAP_MMC_HIGHSPEED is added for DDR support.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When timeout_clk is calculated the host->clock could be zero.
So, instead of host->clock the calculation now uses mmc->f_max.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This moves the calculation below the assignment of mmc->f_max, which
we need for calculating timeout_clk in the next patch in this series.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 4b01681c77, which introduced a new potential
divide by zero in the process of fixing one. The subsequent commits
attempt to fix the issue properly.
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix below compile warning:
CC drivers/mmc/host/tmio_mmc.o
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_suspend':
drivers/mmc/host/tmio_mmc.c:30: warning: unused variable 'mmc'
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_resume':
drivers/mmc/host/tmio_mmc.c:45: warning: unused variable 'mmc'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Apply a workaround for the imx eSDHC controller to avoid missing
card interrupts. This makes SDIO work.
Signed-off-by: Tony Lin <tony.lin@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
A header change has removed an implicit inclusion of module.h, breaking
the build due to the use of THIS_MODULE. Fix that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The mask used inside this macro was assuming Buffer_Size1's [BS1's]
width to be 14 bits, it is actually 13 bits. Modify masks used in
IDMAC_SET_BUFFER1_SIZE such that they use only 13 bits instead of
current 14.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Samsung SoCs need to set BROKEN_ADMA_ZEROLEN_DESC.
(If ADMA operation is more than 65535, maybe set by zero.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable the quirk.
(Best used in conjunction with patch downgrading ADMA to SDMA when
transfer is not aligned.)
Signed-off-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently, the retuning timer for retuning mode 1 will be deleted in
function sdhci_tasklet_finish after a mmc request done, which will make
retuning timing never trigger again. This patch fixed this problem.
Signed-off-by: Aaron Lu <Aaron.Lu@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The patch adds device tree probe support for sdhci-esdhc-imx driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
Neither platform based nor dt based device needs to pass the parent
to sdhci_alloc_host. There is no difference between platform and dt
on this point.
The patch makes the change to pass device itself than its parent to
sdhci_alloc_host for dt case too. Otherwise the probe function of
sdhci based drivers which is shared between platform and dt will
fail on dt case.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
The patch removes all the uses of cpu_is_mx(). Instead, it utilizes
platform_device_id to distinguish the esdhc differences among SoCs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
The patch copies platform data into pltfm_imx_data and reference
the data there than platform data after probe.
This work is inspired by Grant Likely and Troy Kisky.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
The patch extends card_detect and write_protect support to get mx5
family and more scenarios supported. The changes include:
* Turn platform_data from optional to mandatory
* Add cd_types and wp_types into platform_data to cover more use
cases
* Remove the use of flag ESDHC_FLAG_GPIO_FOR_CD
* Adjust some machine codes to adopt the platform_data changes
* Work around the issue that software reset will get card detection
circuit stop working
With this patch, card_detect and write_protect gets supported on
mx5 based platforms.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Chris Ball <cjb@laptop.org>
Fix build issue caused by undefined struct scatterlist in
drivers/mmc/host/tmio_mmc.c.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits)
ARM: msm: platsmp: determine number of CPU cores at boot time
ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461
ARM: Tegra: Trimslice: Tri-state DAP3 pinmux
ARM: orion5x: fixup 5181 MPP mask check
ARM: mxs-dma: include <linux/dmaengine.h>
ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts
ARM: i.MX53: UARTn_CTS pin should not change RTS input select
ARM: i.MX53: UARTn_TXD pin should not change RXD input select
ARM: mx25: Fix typo on CAN1_RX pad setting
iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions
ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: i.MX53: Fix IOMUX type o's
ARM i.MX dma: Fix burstsize settings
mach-mx5: fix the I2C clock parents
ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0
ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h
ARM: mx53: Fix some interrupts marked as reserved.
MXC: iomux-v3: correct NO_PAD_CTRL definition
...
Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
ARM: 7004/1: fix traps.h compile warnings
ARM: 6998/2: kernel: use proper memory barriers for bitops
ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
ARM: Fix build errors caused by adding generic macros
ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
ARM: GIC: avoid routing interrupts to offline CPUs
ARM: CPU hotplug: fix abuse of irqdesc->node
ARM: 6981/2: mmci: adjust calculation of f_min
ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
ARM: ARM_DMA_ZONE_SIZE is no more
ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1287 commits)
icmp: Fix regression in nexthop resolution during replies.
net: Fix ppc64 BPF JIT dependencies.
acenic: include NET_SKB_PAD headroom to incoming skbs
ixgbe: convert to ndo_fix_features
ixgbe: only enable WoL for magic packet by default
ixgbe: remove ifdef check for non-existent define
ixgbe: Pass staterr instead of re-reading status and error bits from descriptor
ixgbe: Move interrupt related values out of ring and into q_vector
ixgbe: add structure for containing RX/TX rings to q_vector
ixgbe: inline the ixgbe_maybe_stop_tx function
ixgbe: Update ATR to use recorded TX queues instead of CPU for routing
igb: Fix for DH89xxCC near end loopback test
e1000: always call e1000_check_for_link() on e1000_ce4100 MACs.
netxen: add fw version compatibility check
be2net: request native mode each time the card is reset
ipv4: Constrain UFO fragment sizes to multiples of 8 bytes
virtio_net: Fix panic in virtnet_remove
ipv6: make fragment identifications less predictable
ipv6: unshare inetpeers
can: make function can_get_bittiming static
...
Fix clock rate setting in the mxs-mmc driver. Previously, if div2 was 0
then the value for TIMING_CLOCK_RATE would have been 255 instead of 0.
The limits for div1 (TIMING_CLOCK_DIVIDE) and div2 (TIMING_CLOCK_RATE+1)
were also not correctly defined.
Can easily be reproduced on mx23evk: default clock for high speed sdio
cards is 50 MHz. With a SSP_CLK of 28.8 MHz default), this resulted in
an actual clock rate of about 56 kHz. Tested on mx23evk.
Signed-off-by: Koen Beel <koen.beel@barco.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently the tmio-mmc driver contains a recursive runtime PM method
invocation, which leads to a deadlock on a mutex. Avoid it by taking
care not to request DMA too early.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
A recent commit "mmc: tmio: Share register access functions" has swapped
arguments of a macro and broken DMA with TMIO MMC. This patch fixes the
arguments back.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch uses runtime PM to allow the system to power down the MMC
controller, when the MMC closk is switched off.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch uses runtime PM to allow the system to power down the MMC
controller, when the MMC closk is switched off.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Calling mmc_request_done() under a spinlock with interrupts disabled
leads to a recursive spin-lock on request retry path and to
scheduling in atomic context. This patch fixes both these problems
by moving mmc_request_done() to the scheduler workqueue.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the case of an I/O error, the DMA will have been cleaned up in
the MMC interrupt and the request structure pointer will be null.
In that case, it is essential to check if the DMA is over before
dereferencing host->mrq->data.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are a few places with the same functionality. This patch creates
two functions omap_hsmmc_set_bus_width() and omap_hsmmc_set_bus_mode()
to do the job.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are two pieces of code which are similar, but not the same.
Each of them contains a bug.
The SYSCTL register should be read before writing to it in
omap_hsmmc_context_restore() to retain the state of the reserved bits.
Before setting the clock divisor and DTO bits the value from the SYSCTL
register should be masked properly. We were lucky to have no problems
with DTO bits. So, make sure we have clear DTO bits properly in
omap_hsmmc_set_ios().
Additionally get rid of msleep(1). The actual time is rarely higher
than 30us on OMAP 3630.
The resulting pieces of code are refactored into the
omap_hsmmc_set_clock() function.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There is similar code in two functions which enable the clock. Refactor
this code to omap_hsmmc_start_clock(). Re-use omap_hsmmc_stop_clock() in
omap_hsmmc_context_restore() as well.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are two places where the same calculations are done.
Let's split them into a separate function.
In addition, simplify by using the DIV_ROUND_UP kernel macro.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Move the min and max frequency constants to the definition block in
the source file.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
CERR and BADA were in the wrong place and there are only
32 not 35.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
After runtime conversion to handle clk, iclk node is not used.
However fclk node is still used to get clock rate.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* Add runtime pm support to HSMMC host controller.
* Use runtime pm API to enable/disable HSMMC clock.
* Use runtime autosuspend APIs to enable auto suspend delay.
Based on OMAP HSMMC runtime implementation by Kevin Hilman and
Kishore Kadiyala.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
lazy_disable framework in OMAP HSMMC manages multiple low power states and
card is powered off after inactivity time of 8 seconds. Based on previous
discussion on the list, card power (regulator) handling (when to power
OFF/ON) should ideally be handled by core layer. Remove usage of lazy
disable to allow core layer _only_ to handle card power. With the removal
of lazy disable framework, MMC regulators are left ON until MMC_POWER_OFF
via set_ios.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
pre_req() runs dma_map_sg() and prepares the dma descriptor for the next
mmc data transfer. post_req() runs dma_unmap_sg. If not calling pre_req()
before mmci_request(), mmci_request() will prepare the cache and dma just
like it did it before. It is optional to use pre_req() and post_req()
for mmci.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
pre_req() runs dma_map_sg(), post_req() runs dma_unmap_sg. If not calling
pre_req() before omap_hsmmc_request(), dma_map_sg will be issued before
starting the transfer. It is optional to use pre_req(). If issuing
pre_req(), post_req() must be called as well.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This driver has been used for years with this option enabled.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Take care of slots while going to suspend state.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Unless MMC_CAP_8_BIT_DATA is set, the bus width defaults to 4.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
And hook platform_8bit_width to support 8-bit bus width.
Signed-off-by: Major Lee <major_lee@wistron.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If an error occurs mid way through a transaction (such as a missing CRC
status response after the 2nd block written out of 3), then the FIFO may
still contain data which will interfere with the next transaction.
Therefore after an error has been detected, reset the fifo using the
CTRL register.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When a data write isn't acknowledged by the card (so no CRC status token
is detected after the data), the error -EIO is returned instead of the
-ETIMEDOUT expected by mmc_test 15 - "Correct xfer_size at write (start
failure)" and 17 "Correct xfer_size at write (midway failure)". In PIO
mode the reported number of bytes transferred is also exaggerated since
the last block actually failed.
Handle the "Write no CRC" error specially, setting the error to
-ETIMEDOUT and setting the bytes_xferred to 0.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Remove error messages for timeout and CRC failure, since the error code
already indicates the problem.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are several situations when dw_mci_submit_data_dma() decides to
fall back to PIO mode instead of using DMA, due to a short (to avoid
overhead) or "complex" (e.g. with unaligned buffers) transaction, even
though host->use_dma is set. However dw_mci_stop_dma() decides whether
to stop DMA or set the EVENT_XFER_COMPLETE event based on host->use_dma.
When falling back to PIO mode this results in data timeout errors
getting missed and the driver locking up.
Therefore add host->using_dma to indicate whether the current
transaction is using dma or not, and adjust dw_mci_stop_dma() to use
that instead.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Wonil Choi <wonil22.choi@samsung.com>
Signed-off-by: Minho Ban <mhban@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In general, SDHC hardware timeout cannot be avoided.
Accordingly, the maximum timeout is specified to limit
the maximum discard size.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The use of flag ESDHC_FLAG_GPIO_FOR_CD_WP is all CD related. It does
not necessarily need to bother WP in the flag name.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The function esdhc_readl_le intends to clear bit SDHCI_CARD_PRESENT,
when the card detect gpio tells there is no card. But it does not
clear the bit actually. The patch gives a fix on that.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The issue was initially found by Eric Benard as below.
http://permalink.gmane.org/gmane.linux.ports.arm.kernel/108031
Not sure about other SDHCI based controller, but on Freescale eSDHC,
the SDHCI_INT_CARD_INSERT bits will be immediately set again when it
gets cleared, if a card is inserted. The driver need to mask the irq
to prevent interrupt storm which will freeze the system. And the
SDHCI_INT_CARD_REMOVE gets the same situation.
The patch fixes the problem based on the initial idea from
Eric Benard.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Eric Benard <eric@eukrea.com>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
There is a race condition in the tmio_mmc_irq() interrupt handler,
caused by the presence of a while loop, which results in warnings of
spurious interrupts. This was found on an HP iPAQ hx4700 whose HTC
ASIC3 reportedly incorporates the Toshiba TC6380AF controller.
Towards the end of a multiple read (CMD18) operation the handler clears
the final RXRDY status bit in the first loop iteration, sees the DATAEND
status bit at the bottom of the loop, and so clears the DATAEND status
bit in the second loop iteration. However the DATAEND interrupt is still
queued in the system somewhere and can't be delivered until the handler
has returned. This second interrupt is then reported as spurious in the
next call to the handler. Likewise for single read (CMD17) operations.
And something similar occurs for multiple write (CMD25) and single write
(CMD24) operations, where CMDRESPEND and TXRQ status bits are cleared in
a single call.
In these cases the interrupt handler clears two separate interrupts when
it should only clear the one interrupt for which it was invoked. The fix
is to remove the while loop.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Only compile tmio_mmc_dma.o when CONFIG_MMC_SDHI is selected (as y or m).
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Update functions for PIO pushing and pulling data to and from the FIFO
so that they can handle unaligned output buffers and unaligned buffer
lengths. This makes more of the tests in mmc_test pass.
Unaligned lengths in pulls are handled by reading the full FIFO item,
and storing the remaining bytes in a small internal buffer (part_buf).
The next data pull will copy data out of this buffer first before
accessing the FIFO again. Similarly, for pushes the final bytes that
don't fill a FIFO item are stored in the part_buf (or sent anyway if
it's the last transfer), and then the part_buf is included at the
beginning of the next buffer pushed.
Unaligned buffers in pulls are handled specially if the architecture
cannot do efficient unaligned accesses, by reading FIFO items into a
aligned local buffer, and memcpy'ing them into the output buffer, again
storing any remaining bytes in the internal buffer. Similarly for pushes
the buffer is memcpy'd into an aligned local buffer then written to the
FIFO.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The FIFO_DEPTH hardware configuration parameter can be found from the
power-on value of RX_WMark in the FIFOTH register. This is used to
initialise the watermarks, but when calculating the number of free fifo
spaces a preprocessor definition is used which is hard coded to 32.
Fix reading the value out of FIFOTH (the default value in the RX_WMark
field is FIFO_DEPTH-1 not FIFO_DEPTH). Allow the fifo depth to be
overriden by platform data (since a bootloader may have changed FIFOTH
making auto-detection unreliable). Store the fifo_depth for later use.
Also fix the calculation to find the number of free bytes in the fifo to
include the fifo depth in the left shift by the data shift, since the
fifo depth is measured in fifo items not bytes.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add brackets around use of the dev argument to the
mci_{read,write}{w,l,q}() macros, for extra safety.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Convert the card insert/remove tasklet to a workqueue, and call the
setpower platform specific callback without the spinlock held. This
means neither of the setpower or get_cd callbacks are called from atomic
context which allows them to sleep.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When a request is made, the card presence is checked and the request is
queued. These two parts must be atomic with respect to card removal, or
a card removal could be handled in between, and the new request wouldn't
get cancelled until another card was inserted. Therefore move the
spinlock protection from dw_mci_queue_request() up into dw_mci_request()
to cover the presence check.
Note that the test_bit() used for the presence check isn't atomic
itself, so should have been protected by a spinlock anyway.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
DMA is only used for transactions exceeding a certain length, otherwise
PIO is used. The TXDR and RXDR interrupts are masked when in DMA mode
but still fire. When switching to PIO mode (e.g. to get SCR field when
an SD card is inserted) these interrupts are not cleared and so they
trigger the ISR as soon as they are unmasked. If the previous DMA did a
write, then the ISR will handle the TXDR interrupt even if the
transaction is a read, completing the transaction without modifying the
read buffer.
This is fixed primarily by clearing these two interrupts before
unmasking them when setting up PIO mode, and also by making the ISR more
robust by only handling TXDR/RXDR in the correct read/write direction.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some controllers require waiting for the bus to become idle
before writing to some registers. I have implemented this
by adding a hook to sd_ctrl_write16() and implementing
a hook for SDHI which waits for the bus to become idle.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Move register access functions into a shared header.
Use sd_ctrl_write16 in tmio_mmc_dma.c:tmio_mmc_enable_dma().
Other than avoiding (trivial) open-coding, the motivation for
this is to allow platform-hooks in access functions to
be applied across all applicable accesses.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reflects at least the current usage of this register
and I think it improves the readability of the code ever so slightly.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Response timeout (RTO), Response crc error (RCRC) and Response error (RE)
signals come with command done (CD) and can be raised preceding command
done (CD). That is these error interrupts and CD can be handled in
separate dw_mci_interrupt(). If mmc_request_done() is called because of
a response timeout before command done has occured, we might send the
next request before the CD of current request is finished. This can
bring about a broken sequence of request and request-done.
And Data error interrupt (DRTO, DCRC, SBE, EBE) and data transfer
over (DTO) have the same problem.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch sets the card_width bit of CTYPE for the corresponding card.
CTYPE[31] and CTYPE[16] correspond respectively to card[15] and card[0]
for 8-bit mode. And CTYPE[15] and CTYPE[0] correspond respectively to
card[15] and CTYPE[0] for 1-bit or 4-bit mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
As suggested by Arnd, move platform data to include/linux/platform_data
in order to improve build coverage for the driver.
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Delete obsolete sdhci-pxa.c, which was previously shared amongst the
entire PXA series. Instead we now use sdhci-pxav3.c for mmp2 and
sdhci-pxav2.c for pxa9xx.
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdhci-pltfm driver for PXAV2 SoCs, such as pxa910.
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Jun Nie <njun@marvell.com>
Signed-off-by: Qiming Wu <wuqm@marvell.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdhci-pltfm driver for PXAV3 SoCs, such as MMP2.
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are a couple of problems left from the sdhci pltfm and OF
consolidation changes.
* When building more than one sdhci-pltfm based drivers in the same
image, linker will give multiple definition error on the sdhci-pltfm
helper functions. For example right now, building sdhci-of-esdhc
and sdhci-of-hlwd together is a valid combination from Kconfig view.
* With the current build method, there is error with building the
drivers as module, but module installation fails with modprobe.
The patch fixes above problems by changing sdhci-pltfm into a module.
To avoid EXPORT_SYMBOL on so many big endian IO accessors, it moves
these accessors into sdhci-pltfm.h as the 'static inline' functions.
As a result, sdhci.h needs to be included in sdhci-pltfm.h, and in
turn can be removed from individual drivers which already include
sdhci-pltfm.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The structure sdhci_pltfm_data is not necessarily to be in a public
header like include/linux/mmc/sdhci-pltfm.h, so the patch moves it
into drivers/mmc/host/sdhci-pltfm.h and eliminates the former one.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The patch turns the sdhci-of-core common stuff into helper functions
added into sdhci-pltfm.c, and makes sdhci-of device drviers self
registered using the same pair of .probe and .remove used by
sdhci-pltfm device drivers.
As a result, sdhci-of-core.c and sdhci-of.h can be eliminated with
those common things merged into sdhci-pltfm.c and sdhci-pltfm.h
respectively.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The patch migrates the use of sdhci_of_host and sdhci_of_data to
sdhci_pltfm_host and sdhci_pltfm_data, so that the former pair can
be eliminated.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The patch turns the common stuff in sdhci-pltfm.c into functions, and
add device drivers their own .probe and .remove which in turn call
into the common functions, so that those sdhci-pltfm device drivers
register itself and keep all device specific things away from common
sdhci-pltfm file.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
