Register 0xcb4 determines if the PTA circuit can control the swtich
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of just setting the coex table directly, we check if the
wifi is under some important activity (scanning|roaming|linking) and
mark the packets as high priority in that case.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When wifi is at 5G band, it does not intefere with 2.4G bt signal,
hence we can just ignore it and transmit normally as nothing happened.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Monitor wifi status and check if it is changed.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Gather multiple coex table settings into a function coex_table_with_type()
and control the coex table according the type value as put in
switch-case expression.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The power_save_state function checks the state of power saving.
For tdma settings, the wifi sends nullfunc to pretend enter power saving
and then bt can transmit. Hence the coex needs to check the power status
before set the pstdma function.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Originally we only increase/decrease bt power in a fixed power gap, this
patch makes us be able to modify bt power for multiple power gaps and we
can precisely adjust the bt power.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function updates the information of bt profiling to help us decide
the network status and dispatch the resource properly.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If there are a lot of low-rate packets, then the connection of wifi is
unstable. If so, we should switch resource to bt to have a higher
transmission quality, or wifi resource will be wasted
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We monitor the packet counter to guess if the bt is slave or not, and
when bt is slave, it may receive packet at any time, so we will have to
take care about it
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larger packets have higher opportunity to be interrupt by bt signal.
In order to shorten the transmission time, control the packet
aggregation size.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
His email is bouncing, and he'd like to use this new one.
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Cc: Ganapathi Bhat <gbhat@marvell.com>
Cc: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'chan_stats' is (re)allocated in _mwifiex_fw_dpc() ->
mwifiex_init_channel_scan_gap(), which is called whenever the device is
initialized -- at probe or at reset.
But we only free it in we completely unregister the adapter, meaning we
leak a copy of it during every reset.
Let's free it in the shutdown / removal paths instead (and in the
error-handling path), to avoid the leak.
Ideally, we can eventually unify much of mwifiex_shutdown_sw() and
mwifiex_remove_card() (way too much copy-and-paste) to reduce the burden
on bugfixes like this. But that's work for tomorrow.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we shut down the device (i.e., during 'reset'), we cancel any
outstanding work, but we don't clear any work-related flags. This can
cause problems if, e.g., we begin to queue a new firmware dump or card
reset while the other one is in progress. That might leave work_flags
with a stale value, and we might begin one of these *after* we've
completely reset the device. That doesn't make sense, because all
firmware context will have been lost by then.
This fixes some forms of cascading failures, where I:
(a) force a firmware dump (cat /sys/kernel/debug/mwifiex/mlan0/device_dump)
(b) run a Wifi scan in parallel (iw mlan0 scan)
(c) the scan times out due to (a) hogging the interface
(d) the command timeout triggers another firmware dump and a reset [*]
(e) the 2nd firmware dump flag persists across the reset
(f) as soon as the interface comes back up, we trigger the pending
firmware dump
(g) subsequent commands time out again, while we are processing the
firmware dump; return to (d)
[*] Note that automatic card_reset() support is not yet implemented for
the mwifiex PCIe driver, so we won't hit *exactly* this behavior yet.
But we can see similarly-confusing behaviors today.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we reset because of a command timeout, we should reset this flag.
Otherwise, we might erroneously think the next command after reset is
timing out, and trigger another reset.
The above behavior effectively neuters the automatic card_reset()
behavior, as it means we will never recover from a command timeout
properly (and in fact, we might enter an infinite loop:
timeout -> reset -> (fake) timeout -> reset -> ...
This fixes a bug introduced with introduction of PCIe function level
reset support, but it was carried into the SDIO driver when it was
converted to use the same codepaths. And this is currently mostly a
problem only in the SDIO driver, because it's the only one with
automatic card_reset() support (e.g., on command timeout). But it will
be a problem for PCIe too, as I'm working on supporting automatic
card_reset() for PCIe.
Fixes: c742e623e9 ("mwifiex: sdio card reset enhancement")
Fixes: 4c5dae59d2 ("mwifiex: add PCIe function level reset support")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Command buffers (skb's) are allocated by the main driver, and freed upon
the last use. That last use is often in mwifiex_free_cmd_buffer(). In
the meantime, if the command buffer gets used by the PCI driver, we map
it as DMA-able, and store the mapping information in the 'cb' memory.
However, if a command was in-flight when resetting the device (and
therefore was still mapped), we don't get a chance to unmap this memory
until after the core has cleaned up its command handling.
Let's keep a refcount within the PCI driver, so we ensure the memory
only gets freed after we've finished unmapping it.
Noticed by KASAN when forcing a reset via:
echo 1 > /sys/bus/pci/.../reset
The same code path can presumably be exercised in remove() and
shutdown().
[ 205.390377] mwifiex_pcie 0000:01:00.0: info: shutdown mwifiex...
[ 205.400393] ==================================================================
[ 205.407719] BUG: KASAN: use-after-free in mwifiex_unmap_pci_memory.isra.14+0x4c/0x100 [mwifiex_pcie] at addr ffffffc0ad471b28
[ 205.419040] Read of size 16 by task bash/1913
[ 205.423421] =============================================================================
[ 205.431625] BUG skbuff_head_cache (Tainted: G B ): kasan: bad access detected
[ 205.439815] -----------------------------------------------------------------------------
[ 205.439815]
[ 205.449534] INFO: Allocated in __build_skb+0x48/0x114 age=1311 cpu=4 pid=1913
[ 205.456709] alloc_debug_processing+0x124/0x178
[ 205.461282] ___slab_alloc.constprop.58+0x528/0x608
[ 205.466196] __slab_alloc.isra.54.constprop.57+0x44/0x54
[ 205.471542] kmem_cache_alloc+0xcc/0x278
[ 205.475497] __build_skb+0x48/0x114
[ 205.479019] __netdev_alloc_skb+0xe0/0x170
[ 205.483244] mwifiex_alloc_cmd_buffer+0x68/0xdc [mwifiex]
[ 205.488759] mwifiex_init_fw+0x40/0x6cc [mwifiex]
[ 205.493584] _mwifiex_fw_dpc+0x158/0x520 [mwifiex]
[ 205.498491] mwifiex_reinit_sw+0x2c4/0x398 [mwifiex]
[ 205.503510] mwifiex_pcie_reset_notify+0x114/0x15c [mwifiex_pcie]
[ 205.509643] pci_reset_notify+0x5c/0x6c
[ 205.513519] pci_reset_function+0x6c/0x7c
[ 205.517567] reset_store+0x68/0x98
[ 205.521003] dev_attr_store+0x54/0x60
[ 205.524705] sysfs_kf_write+0x9c/0xb0
[ 205.528413] INFO: Freed in __kfree_skb+0xb0/0xbc age=131 cpu=4 pid=1913
[ 205.535064] free_debug_processing+0x264/0x370
[ 205.539550] __slab_free+0x84/0x40c
[ 205.543075] kmem_cache_free+0x1c8/0x2a0
[ 205.547030] __kfree_skb+0xb0/0xbc
[ 205.550465] consume_skb+0x164/0x178
[ 205.554079] __dev_kfree_skb_any+0x58/0x64
[ 205.558304] mwifiex_free_cmd_buffer+0xa0/0x158 [mwifiex]
[ 205.563817] mwifiex_shutdown_drv+0x578/0x5c4 [mwifiex]
[ 205.569164] mwifiex_shutdown_sw+0x178/0x310 [mwifiex]
[ 205.574353] mwifiex_pcie_reset_notify+0xd4/0x15c [mwifiex_pcie]
[ 205.580398] pci_reset_notify+0x5c/0x6c
[ 205.584274] pci_dev_save_and_disable+0x24/0x6c
[ 205.588837] pci_reset_function+0x30/0x7c
[ 205.592885] reset_store+0x68/0x98
[ 205.596324] dev_attr_store+0x54/0x60
[ 205.600017] sysfs_kf_write+0x9c/0xb0
...
[ 205.800488] Call trace:
[ 205.802980] [<ffffffc00020a69c>] dump_backtrace+0x0/0x190
[ 205.808415] [<ffffffc00020a96c>] show_stack+0x20/0x28
[ 205.813506] [<ffffffc0005d020c>] dump_stack+0xa4/0xcc
[ 205.818598] [<ffffffc0003be44c>] print_trailer+0x158/0x168
[ 205.824120] [<ffffffc0003be5f0>] object_err+0x4c/0x5c
[ 205.829210] [<ffffffc0003c45bc>] kasan_report+0x334/0x500
[ 205.834641] [<ffffffc0003c3994>] check_memory_region+0x20/0x14c
[ 205.840593] [<ffffffc0003c3b14>] __asan_loadN+0x14/0x1c
[ 205.845879] [<ffffffbffc46171c>] mwifiex_unmap_pci_memory.isra.14+0x4c/0x100 [mwifiex_pcie]
[ 205.854282] [<ffffffbffc461864>] mwifiex_pcie_delete_cmdrsp_buf+0x94/0xa8 [mwifiex_pcie]
[ 205.862421] [<ffffffbffc462028>] mwifiex_pcie_free_buffers+0x11c/0x158 [mwifiex_pcie]
[ 205.870302] [<ffffffbffc4620d4>] mwifiex_pcie_down_dev+0x70/0x80 [mwifiex_pcie]
[ 205.877736] [<ffffffbffc1397a8>] mwifiex_shutdown_sw+0x190/0x310 [mwifiex]
[ 205.884658] [<ffffffbffc4606b4>] mwifiex_pcie_reset_notify+0xd4/0x15c [mwifiex_pcie]
[ 205.892446] [<ffffffc000635f54>] pci_reset_notify+0x5c/0x6c
[ 205.898048] [<ffffffc00063a044>] pci_dev_save_and_disable+0x24/0x6c
[ 205.904350] [<ffffffc00063cf0c>] pci_reset_function+0x30/0x7c
[ 205.910134] [<ffffffc000641118>] reset_store+0x68/0x98
[ 205.915312] [<ffffffc000771588>] dev_attr_store+0x54/0x60
[ 205.920750] [<ffffffc00046f53c>] sysfs_kf_write+0x9c/0xb0
[ 205.926182] [<ffffffc00046dfb0>] kernfs_fop_write+0x184/0x1f8
[ 205.931963] [<ffffffc0003d64f4>] __vfs_write+0x6c/0x17c
[ 205.937221] [<ffffffc0003d7164>] vfs_write+0xf0/0x1c4
[ 205.942310] [<ffffffc0003d7da0>] SyS_write+0x78/0xd8
[ 205.947312] [<ffffffc000204634>] el0_svc_naked+0x24/0x28
...
[ 205.998268] ==================================================================
This bug has been around in different forms for a while. It was sort of
noticed in commit 955ab095c5 ("mwifiex: Do not kfree cmd buf while
unregistering PCIe"), but it just fixed the double-free, without
acknowledging the potential for use-after-free.
Fixes: fc33146090 ("mwifiex: use pci_alloc/free_consistent APIs for PCIe")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A separate wifi-only firmware was download during pcie function level
reset. It is in fact the tail part of wifi/bt combo firmware. Per
Brian's and Dmitry's suggestion, this patch extract the wifi part from
combo firmware.
After that, the mrvl/pcie8997_wlan_v4.bin image in linux-firmware repo
is redundant (though I guess we keep it around to support older
kernels).
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch correct pcie scratch register name, to keep the same with
chipset side definition.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_dbg will do nothing before adapter->dev get assigned. several logs
lost in this case. it can be avoided by fall back to pr_info.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If wakeup interrupt handler is called, we know that the wakeup
interrupt number is valid, there is no need to check it.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
nl80211 provides the NL80211_SCAN_FLAG_RANDOM_ADDR for every scan
request that should be randomized; the absence of such a flag means we
should not randomize. However, mwifiex was stashing the latest
randomization request and *always* using it for future scans, even those
that didn't set the flag.
Let's zero out the randomization info whenever we get a scan request
without NL80211_SCAN_FLAG_RANDOM_ADDR. I'd prefer to remove
priv->random_mac entirely (and plumb the randomization MAC properly
through the call sequence), but the spaghetti is a little difficult to
unravel here for me.
Fixes: c2a8f0ff9c ("mwifiex: support random MAC address for scanning")
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If iwl_pcie_ctxt_info_init_fw_sec() fails, the previous allocated DMA
memory needs to be freed (it even goes out of scope immediately.)
Do that to prevent the leak.
Fixes: eda50cde58 ("iwlwifi: pcie: add context information support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the context info fails to be allocated, the mutex
isn't unlocked properly, fix that.
Fixes: eda50cde58 ("iwlwifi: pcie: add context information support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When FW fails to get block ack, it will send the notification with
0 items in the TFD queue elements. Allow this and handle accordingly.
Fixes: c46e7724bf ("iwlwifi: mvm: support new BA notification response")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
I noticed that reading the snapshot file when it is empty no longer gives a
status. It suppose to show the status of the snapshot buffer as well as how
to allocate and use it. For example:
># cat snapshot
# tracer: nop
#
#
# * Snapshot is allocated *
#
# Snapshot commands:
# echo 0 > snapshot : Clears and frees snapshot buffer
# echo 1 > snapshot : Allocates snapshot buffer, if not already allocated.
# Takes a snapshot of the main buffer.
# echo 2 > snapshot : Clears snapshot buffer (but does not allocate or free)
# (Doesn't have to be '2' works with any number that
# is not a '0' or '1')
But instead it just showed an empty buffer:
># cat snapshot
# tracer: nop
#
# entries-in-buffer/entries-written: 0/0 #P:4
#
# _-----=> irqs-off
# / _----=> need-resched
# | / _---=> hardirq/softirq
# || / _--=> preempt-depth
# ||| / delay
# TASK-PID CPU# |||| TIMESTAMP FUNCTION
# | | | |||| | |
What happened was that it was using the ring_buffer_iter_empty() function to
see if it was empty, and if it was, it showed the status. But that function
was returning false when it was empty. The reason was that the iter header
page was on the reader page, and the reader page was empty, but so was the
buffer itself. The check only tested to see if the iter was on the commit
page, but the commit page was no longer pointing to the reader page, but as
all pages were empty, the buffer is also.
Cc: stable@vger.kernel.org
Fixes: 651e22f270 ("ring-buffer: Always reset iterator to reader page")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This state bit was added as a way for DCB to avoid having to wait for
the queues to disable when handling LLDP events. The logic for this was
burried deep within stop Tx and stop Rx queue code. First, let's rename
it so that it does not appear to only affect Tx when infact it modifies
both Tx and Rx flow. Second we can move it up into the i40e_stop_rings()
function, and we can simply re-use the i40e_stop_rings_no_wait() so that
we don't have to bury the implementation as deep into the call stack.
An alternative might be to remove the state bit and instead attempt to
shut down everything directly in DCP flow. This, however, is not ideal
because it creates yet another separate shutdown routine that we'd have
to maintain. In the current implementation any changes will be made to
both flows.
Change-ID: I68e1ccb901af320862bca395e9c9746f08e8b17c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there are a lot of active VFs, it can take multiple seconds to
finish resetting all of them during certain flows., which can cause some
VFs to fail to wait long enough for the reset to occur. The user might
see messages like "Never saw reset" or "Reset never finished" and the VF
driver will stop functioning properly.
The naive solution would be to simply increase the wait timer. We can
get much more clever. Notice that i40e_reset_vf is run in a serialized
fashion, and includes lots of delays.
There are two prominent delays which take most of the time. First, when
we begin resetting VFs, we have multiple 10ms delays which accrue
because we reset each VF in a serial fashion. These delays accumulate to
almost 4 seconds when handling the maximum number of VFs (128).
Secondly, there is a massive 50ms delay for each time we disable queues
on a VSI. This delay is necessary to allow HW to finish disabling queues
before we restore functionality. However, just like with the first case,
we are paying the cost for each VF, rather than disabling all VFs and
waiting once.
Both of these can be fixed, but required some previous refactoring to
handle the special case. First, we will need the
i40e_vsi_wait_queues_disabled function which was previously DCB
specific. Second, we will need to implement our own
i40e_vsi_stop_rings_no_wait function which will handle the stopping of
rings without the delays.
Finally, implement an i40e_reset_all_vfs function, which will first
start the reset of all VFs, and pay the wait cost all at once, rather
than serially waiting for each VF before we start processing then next
one. After the VF has been reset, we'll disable all the VF queues, and
then wait for them to disable. Again, we'll organize the flow such that
we pay the wait cost only once.
Finally, after we've disabled queues we'll go ahead and begin restoring
VF functionality. The result is reducing the wait time by a large factor
and ensuring that VFs do not timeout when waiting in the VF driver.
Change-ID: Ia6e8cf8d98131b78aec89db78afb8d905c9b12be
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future patch is going to want to re-use some of the code in
i40e_reset_vf, so lets break up the beginning and ending parts into
their own helper functions. The first function will be used to
initialize the reset on a VF, while the second function will be used to
finalize the reset and restore functionality.
Change-ID: I48df808b8bf09de3c2ed8c521f57b3f0ab9e5907
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This flag was originally intended to be used to let some
driver code know when we were running from netpoll.
Ultimately this was not necessary and we never used it.
Let's remove it
Change-ID: I43b72483d91c1638071d2a7f389ab171ec5b796a
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When sending an adminq command, we wait for the command to complete in
a loop. This loop waits for an entire millisecond, when in practice the
adminq command is processed often much faster.
Change the loop to use i40e_usec_delay instead, and wait for 50 usecs
each time instead. This appears to be about the minimum time required,
based on some manual observation and testing.
The primary benefit of this change is reducing latency of various
operations in the PF driver, especially when related to having a large
number of VFs enabled.
For example, on Linux, when instantiating 128 VFs, the time to finish
the operation dropped from about 9 seconds down to under 6 seconds.
Additionally, the time it takes to finish a PF reset with 128 VFs
dropped from 5.1 seconds down to 0.7 seconds.
As the examples above show, a significant portion of the delay is wasted
waiting for admiqn operations which have already finished.
This patch shouldn't cause impact to functionality, as we still check
and keep waiting until the command does get processed. The only expected
change is an increase in CPU utilization as we now check for completion
far more times. However, in practice the commands appear to generally be
complete within the first delay window anyways.
Change-ID: If8af8388e100da0a14eaf9e1af3afadf73a958cf
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The check for I40E_CONFIG_BUSY state bit in the i40e_set_link_ksettings
function is fishy. First we can notice a few things about the check here.
First a similar check was introduced by commit
'c7d05ca89f8e ("i40e: driver ethtool core")'
Later a commit introducing the link settings was added by commit
'bf9c71417f72 ("i40e: Implement set_settings for ethtool")'
However, this second check was against vsi->state instead of pf->state,
and also failed to set the bit, it only checks. That indicates the locking
was not quite correct. The only other place that the state bit
in vsi->state gets used is to protect the filter list.
Since this code does not care about the mac filter list, and seems
clear the original code should have set the pf->state bit. Fix these
issues by using pf->state correctly, and by actually setting the bit
so that we properly lock as expected.
Since these checks occur while holding the rtnl_lock(), lets also add a
timeout so that we don't potentially softlock the system.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
and then two Allwinner clk driver build fixes and two CPU clk driver fixes
where we see random CPUFreq crashes because the CPU's PLL locks up sometimes
when we change the rate.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=EujZ
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd"
- one stm32f4 fix for a change that introduced the PLL_I2S and PLL_SAI
boards
- two Allwinner clk driver build fixes
- two Allwinner CPU clk driver fixes where we see random CPUFreq
crashes because the CPU's PLL locks up sometimes when we change the
rate
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: a33: gate then ungate PLL CPU clk after rate change
clk: sunxi-ng: Add clk notifier to gate then ungate PLL clocks
clk: sunxi-ng: fix build failure in ccu-sun9i-a80 driver
clk: sunxi-ng: fix build error without CONFIG_RESET_CONTROLLER
clk: stm32f4: fix: exclude values 0 and 1 for PLLQ
A future patch will need to be able to handle controlling queues without
waiting until all VSIs are handled. Factor out the direct queue
modification so that we can easily re-use this code. The result is also
a bit easier to read since we don't embed multiple single-letter loop
counters.
Change-ID: Id923cbfa43127b1c24d8ed4f809b1012c736d9ac
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull CIFS fix from Steve French:
"One more cifs fix for stable"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Do not send echoes before Negotiate is complete
We made some effort to reduce the RTNL lock scope when resetting and
rebuilding the PF. Unfortunately we still held the RTNL lock during the
VF reset operation, which meant that multiple PFs could not reset in
parallel due to the global lock. For now, further reduce the scope by
not holding the RTNL lock while resetting VFs. This allows multiple PFs
to reset in a timely manner.
Change-ID: I2fbf823a0063f24dff67676cad09f0bbf83ee4ce
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds tracepoints to the i40e and i40evf drivers to which
BPF programs can be attached for feature testing and verification.
It's expected that an attached BPF program will identify and count or
log some interesting subset of traffic. The bcc-tools package is
helpful there for containing all the BPF arcana in a handy Python
wrapper. Though you can make these tracepoints log trace messages, the
messages themselves probably won't be very useful (other to verify the
tracepoint is being called while you're debugging your BPF program).
The idea here is that tracepoints have such low performance cost when
disabled that we can leave these in the upstream drivers. This may
eventually enable the instrumentation of unmodified customer systems
should the need arise to verify a NIC feature is working as expected.
In general this enables one set of feature verification tools to be
used on these drivers whether they're built with the kernel or
separately.
Users are advised against using these tracepoints for anything other
than a diagnostic tool. They have a performance impact when enabled,
and their exact placement and form may change as we see how well they
work in practice for the purposes above.
Change-ID: Id6014a7322c0e6d08068114dd20bd156f2f6435e
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dump some internal state about VFs through debugfs. This provides
information not available with 'ip link show'. To use, write "dump vf
<id>" to the command file, or just "dump vf" to dump information on all
of the VFs.
Change-ID: Ibe32b7f4ae55d4358c0b903217475f708ada1ecd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue I introduced when I converted the code over to
using the length field to determine if a descriptor was done or not. It
turns out that we are also processing programming descriptors in the Rx
path and need to have these processed even though the length field will be
0 on these packets. What will happen with a programming descriptor is that
we will receive a descriptor that has the SPH bit set, and the header
length and packet length fields cleared.
To account for this we should be checking for the bit for split header
being set even though we aren't actually using header split. This bit is
set in the length field to indicate if a programming descriptor response is
contained in the descriptor. Since we don't support header split we don't
need to perform the extra checks of using a fixed value for the entire
length field.
In addition I am moving the function for checking if a filter is a
programming status filter into the i40e_txrx.c file since there is no
longer support for FCoE it doesn't make sense to keep this file in i40e.h.
Change-ID: I12c359c3dc70adb9d6b92b27324bb2c7f04c1a06
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rx checksum offload for tunneled packets was never being negotiated or
requested by VF. This capability was assumed by default and enabled in
current hardware for VF. Going forward, this feature needs to be disabled
or advanced ptypes should be negotiated with PF in the future.
Change-ID: I9e54cfa8a90e03ab6956db4412f1e337ccd2c2e0
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of using a private copy of struct net_device_stats in
struct i40evf_adapter, use stats from struct net_device. Also remove the
now unnecessary .ndo_get_stats function.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Andrey reported a use-after-free in __ns_get_path():
spin_lock include/linux/spinlock.h:299 [inline]
lockref_get_not_dead+0x19/0x80 lib/lockref.c:179
__ns_get_path+0x197/0x860 fs/nsfs.c:66
open_related_ns+0xda/0x200 fs/nsfs.c:143
sock_ioctl+0x39d/0x440 net/socket.c:1001
vfs_ioctl fs/ioctl.c:45 [inline]
do_vfs_ioctl+0x1bf/0x1780 fs/ioctl.c:685
SYSC_ioctl fs/ioctl.c:700 [inline]
SyS_ioctl+0x8f/0xc0 fs/ioctl.c:691
We are under rcu read lock protection at that point:
rcu_read_lock();
d = atomic_long_read(&ns->stashed);
if (!d)
goto slow;
dentry = (struct dentry *)d;
if (!lockref_get_not_dead(&dentry->d_lockref))
goto slow;
rcu_read_unlock();
but don't use a proper RCU API on the free path, therefore a parallel
__d_free() could free it at the same time. We need to mark the stashed
dentry with DCACHE_RCUACCESS so that __d_free() will be called after all
readers leave RCU.
Fixes: e149ed2b80 ("take the targets of /proc/*/ns/* symlinks to separate fs")
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert has reported a freeze during PM resume and some additional
debugging has shown that the device_resume worker cannot make a forward
progress because it waits for an event which is stuck waiting in
drain_all_pages:
INFO: task kworker/u4:0:5 blocked for more than 120 seconds.
Not tainted 4.11.0-rc7-koelsch-00029-g005882e53d62f25d-dirty #3476
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/u4:0 D 0 5 2 0x00000000
Workqueue: events_unbound async_run_entry_fn
__schedule
schedule
schedule_timeout
wait_for_common
dpm_wait_for_superior
device_resume
async_resume
async_run_entry_fn
process_one_work
worker_thread
kthread
[...]
bash D 0 1703 1694 0x00000000
__schedule
schedule
schedule_timeout
wait_for_common
flush_work
drain_all_pages
start_isolate_page_range
alloc_contig_range
cma_alloc
__alloc_from_contiguous
cma_allocator_alloc
__dma_alloc
arm_dma_alloc
sh_eth_ring_init
sh_eth_open
sh_eth_resume
dpm_run_callback
device_resume
dpm_resume
dpm_resume_end
suspend_devices_and_enter
pm_suspend
state_store
kernfs_fop_write
__vfs_write
vfs_write
SyS_write
[...]
Showing busy workqueues and worker pools:
[...]
workqueue mm_percpu_wq: flags=0xc
pwq 2: cpus=1 node=0 flags=0x0 nice=0 active=0/0
delayed: drain_local_pages_wq, vmstat_update
pwq 0: cpus=0 node=0 flags=0x0 nice=0 active=0/0
delayed: drain_local_pages_wq BAR(1703), vmstat_update
Tetsuo has properly noted that mm_percpu_wq is created as WQ_FREEZABLE
so it is frozen this early during resume so we are effectively
deadlocked. Fix this by dropping WQ_FREEZABLE when creating
mm_percpu_wq. We really want to have it operational all the time.
Fixes: ce612879dd ("mm: move pcp and lru-pcp draining into single wq")
Reported-and-tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Debugged-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a single bug in the PWM backlight driver and make it play nice
with a wider range of GPIO devices. This bug is a regression and was
independently discovered by Geert Uytterhoevan and Paul Kocialkowski
(and is tested by both).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=XVXE
-----END PGP SIGNATURE-----
Merge tag 'backlight-for-v4.11' of git://git.linaro.org/people/daniel.thompson/linux
Pull backlight fix from Daniel Thompson:
"Normally pull requests for backlight come from Lee Jones (and will
continue to do so) but the bug fixed here is annoying for few people
so I'm providing a little holiday cover.
Fix a single bug in the PWM backlight driver and make it play nice
with a wider range of GPIO devices. This bug is a regression and was
independently discovered by Geert Uytterhoevan and Paul Kocialkowski
(and is tested by both)"
* tag 'backlight-for-v4.11' of git://git.linaro.org/people/daniel.thompson/linux:
backlight: pwm_bl: Fix GPIO out for unimplemented .get_direction()
gcc -O2 cannot always prove that the loop in acpi_power_get_inferred_state()
is enterered at least once, so it assumes that cur_state might not get
initialized:
drivers/acpi/power.c: In function 'acpi_power_get_inferred_state':
drivers/acpi/power.c:222:9: error: 'cur_state' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This sets the variable to zero at the start of the loop, to ensure that
there is well-defined behavior even for an empty list. This gets rid of
the warning.
The warning first showed up when the -Os flag got removed in a bug fix
patch in linux-4.11-rc5.
I would suggest merging this addon patch on top of that bug fix to avoid
introducing a new warning in the stable kernels.
Fixes: 61b79e16c6 (ACPI: Fix incompatibility with mcount-based function graph tracing)
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The recent introduced MQ IO scheduler breaks mtip32xx in the
following way.
mtip32xx use the 'request_index' passed to .init_request() as
hardware tag index for initializing hardware queue, and it
actually require that rq->tag is always same with 'request_index'
passed to .init_request(). Current blk-mq IO scheduler can't
guarantee this point, so this patch passes BLK_MQ_F_NO_SCHED
and at least make mtip32xx working.
This patch fixes the following strange hardware failure. The
issue can be triggered easily when doing I/O with mq-deadline
enabled.
[ 186.972578] {1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 32993
[ 186.972578] {1}[Hardware Error]: event severity: fatal
[ 186.972579] {1}[Hardware Error]: Error 0, type: fatal
[ 186.972580] {1}[Hardware Error]: section_type: PCIe error
[ 186.972580] {1}[Hardware Error]: port_type: 0, PCIe end point
[ 186.972581] {1}[Hardware Error]: version: 1.0
[ 186.972581] {1}[Hardware Error]: command: 0x0407, status: 0x0010
[ 186.972582] {1}[Hardware Error]: device_id: 0000:07:00.0
[ 186.972582] {1}[Hardware Error]: slot: 4
[ 186.972583] {1}[Hardware Error]: secondary_bus: 0x00
[ 186.972583] {1}[Hardware Error]: vendor_id: 0x1344, device_id: 0x5150
[ 186.972584] {1}[Hardware Error]: class_code: 008001
[ 186.972585] Kernel panic - not syncing: Fatal hardware error!
Reported-by: Jozef Mikovic <jmikovic@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If one driver claims that it doesn't support io scheduler via
BLK_MQ_F_NO_SCHED, we should not allow to change and show the
availabe io schedulers.
This patch adds check to enhance this behaviour.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
