I've been waing a long time for the generic sideband driver to
appear. Patience has run out, so include the minimum here to
just read registers.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Patrick Geary <patrickg@supermicro.com>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170803210536.5662-1-tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Basically, there are full memory mirroring and address range partial
memory mirroring (supported by Haswell EX and Broadwell EX) modes.
a) In full memory mirroring, the memory behind each memory controller
is mirrored, i.e. the memory is split into two identical mirrors
(primary and secondary), half of the memory is reserved for redundancy.
b) In address range partial memory mirroring, the memory size (range)
of primary and secondary behind each memory controller can be user
defined by the TAD0 register. The rest of memory ranges defined by
TAD1/TAD2/... in that memory controller are non-mirrored.
For more detail on memory mirroring, see the following link written by Tony Luck:
https://01.org/lkp/blogs/tonyluck/2016/address-range-partial-memory-mirroring-linux
Currently the sb_edac driver only supports address decoding in full
memory mirroring and non-mirroring modes. In address range partial
memory mirroring mode, it may fail to decode an address that falls in a
non-mirroring area (the following was one of this kind of failed logs).
mce: Uncorrected hardware memory error in user-access at 566d53a400
Memory failure: 0x566d53a: Killing einj_mem_uc:4647 due to hardware memory corruption
Memory failure: 0x566d53a: recovery action for dirty LRU page: Recovered
mce: [Hardware Error]: Machine check events logged
EDAC sbridge MC1: HANDLING MCE MEMORY ERROR
EDAC sbridge MC1: CPU 48: Machine Check Event: 0 Bank 7: ec00000000010090
EDAC sbridge MC1: TSC 4b914aa5a99dab
EDAC sbridge MC1: ADDR 566d53a400
EDAC sbridge MC1: MISC 1443a0c86
EDAC sbridge MC1: PROCESSOR 0:406f1 TIME 1499712764 SOCKET 2 APIC 80
EDAC MC1: 0 UE Can't discover the memory rank for ch addr 0x7fb54e900 on any memory ( page:0x0 offset:0x0 grain:32)
mce: [Hardware Error]: Machine check events logged
Therefore, classify memory mirroring modes and make the address decoding
in address range partial memory mode correct.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170730180651.30060-1-qiuxu.zhuo@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing of
the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170718214339.7774-19-robh@kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
It is a write-only variable so get rid of it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Robert Richter <rric@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Mark Gross <mark.gross@intel.com>
Cc: Tim Small <tim@buttersideup.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: "Arvind R." <arvino55@gmail.com>
Cc: Jason Baron <jbaron@akamai.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Cc: Loc Ho <lho@apm.com>
Cc: linux-edac@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mips@linux-mips.org
Using the homegrown amd_get_nb_id() to find a node ID on AMD was fine
while the L3 to node mapping was 1:1. And Zen topology broke this. So
let's start slowly moving away from it and use the topology interfaces
instead.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/1490041614-90057-2-git-send-email-Yazen.Ghannam@amd.com
[ Massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Non-existent or empty DIMM slots result in error return from
RD_REGP(). But we shouldn't give up on failure.
So long as we find at least one DIMM we can continue.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170628234407.21521-1-tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
The function sbi_send() is local to just pnd2_edac.c and does not need
to be in global scope, so make it static.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170623084855.9197-1-colin.king@canonical.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Add code comment to make it clear that the fall-through is intentional
and, OR ret with its previous value to avoid overwriting it so that
callers can check the correct return value.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170622220535.GA4896@embeddedgus
[ Massage a bit. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Use of_address_to_resource() and resource_size() instead of manually
parsing the "reg" property from the "memory" node(s).
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Thor Thayer <thor.thayer@linux.intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170606235500.22772-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Borislav Petkov <bp@suse.de>
Xiaolong Ye reported the following failure on Broadwell D server:
EDAC sbridge: Some needed devices are missing
EDAC MC: Removed device 0 for sbridge_edac.c Broadwell SrcID#0_Ha#0: DEV 0000:ff:12.0
EDAC sbridge: Couldn't find mci handler
EDAC sbridge: Failed to register device with error -19.
Broadwell D (only IMC0 per socket) and Broadwell X (IMC0 and IMC1 per
socket) use the same PCI device IDs for IMC0 per socket, then they
share pci_dev_descr_broadwell_table (n_imcs_per_sock=2). In this case,
Broadwell D wrongly creates the nonexistent SOCK EDAC memory controller
and reports above error messages, since it has no IMC1 per socket.
Avoid creating the nonexistent SOCK memory controller.
Reported-and-tested-by: Xiaolong Ye <xiaolong.ye@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170608113351.25323-1-qiuxu.zhuo@intel.com
[ Massage. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
edac_op_state is a module parameter which affects the behaviour of
the driver probe which can potentially be invoked as soon as the
platform driver registration happens. Because of this we need to
ensure that we sanity check the module parameter before calling
platform_register_drivers().
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170607215530.8604-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Borislav Petkov <bp@suse.de>
Compare the number of debugfs entries created by
thunderx_create_debugfs_nodes() with the requested number of entries to
properly determine whether to print a warning.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@caviumnetworks.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/20170531155157.93583-1-stemerkhanov@cavium.com
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Check the return status of platform_driver_register() in
mv64x60_edac_init(). Only output messages and initialise the
edac_op_state if the registration is successful.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/20170529212142.25572-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Borislav Petkov <bp@suse.de>
Kaby Lake seems to work just like Skylake.
Reported-and-tested-by: Doug Thompson <bc.tdw@recursor.net>
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1495823683-32569-1-git-send-email-jbaron@akamai.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Collapse 'case:' in *_mci_bind_devs() and update driver version from
1.1.1 to 1.1.2.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170523000934.87971-1-qiuxu.zhuo@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
This is based on previous work by Patrick Geary, see Link.
Additional cleanups ontop:
- Remove the code to read MCMTR from pci_ha1_ta and CHN_TO_HA macro,
now that TA0 and TA1 are unified.
- Remove get_pdev_same_bus(), since in get_dimm_config() the
variable "pvt->pci_ta" for KNL is also ready, we can simply use
pci_read_config_dword(pvt->pci_ta, KNL_MCMTR, &pvt->info.mcmtr) to read
MCMTR.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/57884350.1030401@supermicro.com
Link: http://lkml.kernel.org/r/20170523000910.87925-1-qiuxu.zhuo@intel.com
[ Make __populate_dimms() return int. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
We don't need this quirk anymore now that the EDAC memory controller
representation matches the hardware.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170523000834.87881-1-qiuxu.zhuo@intel.com
[ Commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Tony pointed out: "currently the driver pretends there is one big
8-channel memory controller per socket instead of 2 4-channel
controllers. This is fine with all memory controller populated with
symmetrical DIMM configurations, but runs into difficulties on
asymmetrical setups".
Restructure the driver to assign an EDAC memory controller to each real
h/w memory controller to resolve the issue.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170523000731.87793-1-qiuxu.zhuo@intel.com
[ Break some lines at convenient points. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
EDAC assigns logical memory controller numbers in the order that we find
memory controllers, which depends on which PCI bus they are on. Some
systems end up with MC0 on socket0, others (e.g Haswell) have MC0 on
socket3.
All this is made more confusing for users because we use the string
"Socket" while generating names for memory controllers, but the number
that we attach there is the memory controller number. E.g.
EDAC MC0: Giving out device to module sbridge_edac.c controller
Haswell Socket#0: DEV 0000:ff:12.0 (INTERRUPT)
Change the names to say "SrcID#%d" (where the number we use is read from
the h/w associated with the memory controller instead of some logical
number internal to the EDAC driver). New message:
EDAC MC0: Giving out device to module sbridge_edac.c controller
Haswell SrcID#3: DEV 0000:ff:12.0 (INTERRUPT)
Reported-by: Andrey Korolyov <andrey@xdel.ru>
Reported-by: Patrick Geary <patrickg@supermicro.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170523000603.87748-1-qiuxu.zhuo@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Each of the PCI device IDs belongs to a CPU socket, or to one of the
integrated memory controllers. Provide an enum to specify the domain of
each, and distinguish the resource number in each domain: the number
of the PCI device IDs per integrated memory controller/socket, and the
number of integrated memory controllers per socket.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170523000533.87704-1-qiuxu.zhuo@intel.com
[ Realign pci_dev_descr_knl members. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
struct irq_domain_ops is not modified, so it can be made const.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Thor Thayer <thor.thayer@linux.intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170524133505.1233-1-tklauser@distanz.ch
Signed-off-by: Borislav Petkov <bp@suse.de>
The wrong index into the csbases/csmasks arrays was being passed to
the function to compute the chip select sizes, which resulted in the
wrong size being computed. Address that so that the correct values are
computed and printed.
Also, redo how we calculate the number of pages in a CS row.
Reported-by: Benjamin Bennett <benbennett@gmail.com>
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Cc: <stable@vger.kernel.org> # 4.10.x
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1493313114-11260-1-git-send-email-Yazen.Ghannam@amd.com
[ Remove unneeded integer math comment, minor cleanups. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Leave it to the user to decide whether to enable this or not. Otherwise,
platform-specific drivers won't initialize (currently, EDAC supports
only a single platform driver loaded).
Signed-off-by: Borislav Petkov <bp@suse.de>
Move all the EDAC core functionality behind CONFIG_EDAC and get rid of
that indirection. Update defconfigs which had it.
While at it, fix dependencies such that EDAC depends on RAS for the
tracepoints.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: linux-edac@vger.kernel.org
Use mc_devices list instead to check whether we have EDAC driver
instances successfully registered with EDAC core.
Signed-off-by: Borislav Petkov <bp@suse.de>
Apparently, some machines used to report DRAM errors through a PCI SERR
NMI. This is why we have a call into EDAC in the NMI handler. See
c0d1217202 ("drivers/edac: add new nmi rescan").
From looking at the patch above, that's two drivers: e752x_edac.c and
e7xxx_edac.c. Now, I wanna say those are old machines which are probably
decommissioned already.
Tony says that "[t]the newest CPU supported by either of those drivers
is the Xeon E7520 (a.k.a. "Nehalem") released in Q1'2010. Possibly some
folks are still using these ... but people that hold onto h/w for 7
years generally cling to old s/w too ... so I'd guess it unlikely that
we will get complaints for breaking these in upstream."
So even if there is a small number still in use, we did load EDAC with
edac_op_state == EDAC_OPSTATE_POLL by default (we still do, in fact)
which means a default EDAC setup without any parameters supplied on the
command line or otherwise would never even log the error in the NMI
handler because we're polling by default:
inline int edac_handler_set(void)
{
if (edac_op_state == EDAC_OPSTATE_POLL)
return 0;
return atomic_read(&edac_handlers);
}
So, long story short, I'd like to get rid of that nastiness called
edac_stub.c and confine all the EDAC drivers solely to drivers/edac/. If
we ever have to do stuff like that again, it should be notifiers we're
using and not some insanity like this one.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
The peripherals' RAS functionality only exist on the Arria10 SoCFPGA.
The Cyclone5 initialization generates EDAC warnings when the peripherals
aren't found in the device tree. Fix by checking for Arria10 in the init
functions.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1491415262-5018-1-git-send-email-thor.thayer@linux.intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
DIMM number passed to edac_mc_handle_error() was accidentally hardcoded
to zero. Pass in the correct daddr->dimm value.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Provide debugfs function stubs when EDAC_DEBUG is not enabled so that we
don't fail the build:
drivers/edac/pnd2_edac.c: In function ‘pnd2_init’:
drivers/edac/pnd2_edac.c:1521:2: error: implicit declaration of function ‘setup_pnd2_debug’ [-Werror=implicit-function-declaration]
setup_pnd2_debug();
^
drivers/edac/pnd2_edac.c: In function ‘pnd2_exit’:
drivers/edac/pnd2_edac.c:1529:2: error: implicit declaration of function ‘teardown_pnd2_debug’ [-Werror=implicit-function-declaration]
teardown_pnd2_debug();
^
Signed-off-by: Borislav Petkov <bp@suse.de>
Initial target for this driver is the Intel Apollo Lake platform and
Denverton micro-server, they use the same internal memory controller IP
called Pondicherry2.
Memory controller registers are not in PCI config space like earlier
Intel memory controllers. For Apollo Lake platform they are accessed via
a "side-band" interface, for Denverton micro-server they are access via
PCI config space and memory map I/O. This driver is for Apollo Lake and
Denverton, but only the Denverton is fully enabled while we wait for the
sideband driver.
Apollo lake driver and initial cut at Denverton driver by Tony Luck.
Extensive cleanup, refactoring and basic verification by Qiuxu Zhuo.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170308174539.14432-1-qiuxu.zhuo@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
The MTR_DRAM_WIDTH macro returns the data width. It is sometimes used
as if it returned a boolean true if the width if 8. Fix the tests where
MTR_DRAM_WIDTH is misused.
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170309011809.8340-1-jeremy.lefaure@lse.epita.fr
Signed-off-by: Borislav Petkov <bp@suse.de>
