Some persistent settings were using hex and others decimal. In some cases,
values were set in hex but reported in decimal. Confusing.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are a lot of crappy controllers out there that cannot handle
all the request sizes that the MMC/SD/SDIO specifications require.
In case the card driver can pad the data to overcome the problems,
this commit adds a helper that calculates how much that padding
should be.
A corresponding helper is also added for SDIO, but it can also deal
with all the complexities of splitting up a large transfer efficiently.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Now that we have a specific lock to protect the network
device unicast and multicast lists, remove extraneous
grabs of the TX lock in cases where the code only needs
address list protection.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_addr_{lock,unlock}{,_bh}() helpers.
Use them to protect operations that operate on or read
the network device unicast and multicast address lists.
Also use them in cases where the code simply wants to
block calls into the driver's ->set_rx_mode() and
->set_multicast_list() methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixing unaligned memory access on the blackfin architecture.
Signed-off-by: Ihar Hrachyshka <ihar.hrachyshka@promwad.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle .reset_resume() so that libertas can survive suspend/resume without
reloading the firmware.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Deepak Saxena <dsaxena@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Three major portions to this change:
1) Add IW_EV_COMPAT_LCP_LEN, IW_EV_COMPAT_POINT_OFF,
and IW_EV_COMPAT_POINT_LEN helper defines.
2) Delete iw_stream_check_add_*(), they are unused.
3) Add iw_request_info argument to iwe_stream_add_*(), and use it to
size the event and pointer lengths correctly depending upon whether
IW_REQUEST_FLAG_COMPAT is set or not.
4) The mechanical transformations to the drivers and wireless stack
bits to get the iw_request_info passed down into the routines
modified in #3. Also, explicit references to IW_EV_LCP_LEN are
replaced with iwe_stream_lcp_len(info).
With a lot of help and bug fixes from Masakazu Mokuno.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helps against lost interrupts and aids in debugging this.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes an issus that made "iwconfig eth1 power on" non-working.
When we get a "PS sleep" event, we have to confirm this to the firmware.
The confirm happens with a command, but this command is special: the
firmware won't send us a response. if_cs_host_to_card() is setting
priv->dnld_sent anyway, so this variable stayed at DNLD_DATA_SENT and
was never cleared back.
Now I put the special knowledge that the CMD_802_11_PS_MODE with
CMD_SUBCMD_SLEEP_CONFIRMED doesn't need to need a response by directly
clearing the dnld_sent state in lbs_send_confirmsleep().
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old code misbehaved because it polled card status and always called the
"tx over" code-path.
This also fixes a hard lockup by not allowing and card interrupts while
transferring a TX frame or a command into the card.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implemented rate adaptation support via 'iwconfig rate' API. It is now
possible to specify a bit-rate value and append 'auto'. That will configure
rate adaptation to use all bit-rates equal or lower than than selected value.
Made lbs_cmd_802_11_rate_adapt_rateset a direct command.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we don't check for a command response early, but rather sleep,
then we might sleep despite an already-received command response.
This will lead to a command-timeout.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... because lbs_pr_XXX prefixes all messages with "libertas: "
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Keep the timeout the same (1000*500 == 100000 * 5), but take shorter
naps. Makes downloading the firmware slightly faster.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
priv->driver_lock has already been unlocked some lines above. This patch
fixes the sparse warning:
drivers/net/wireless/libertas/main.c:792:6: warning: context problem in 'lbs_thread': '_spin_unlock_irq' expected different context
drivers/net/wireless/libertas/main.c:792:6: context 'lock': wanted >= 1, got 0
Signed-of-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[PATCH, take 2] libertas: reduce command retry time
In the normal case, an unsuccessful command would be retried for 10*5 seconds,
or 10*10 seconds in the worst case. This patch reduces this to 3*3 seconds,
or 3*10 seconds in the worst case.
I also reduced the time it takes to start a new command downloaded.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will create the following entry:
/sys/class/net/mshX
-- boot_options
| |-- ...
| `-- channel
...
... which I overlooked on my previous patch.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is based on a patch from Shailendra Govardhan and Brian Cavagnolo.
It extends the MESH_CONFIG command to configure non-volatile parameters on
libertas devices that support them (e.g. OLPC Active Antenna).
This patch only implements the driver/firmware interface.
See http://dev.laptop.org/ticket/6823 for minimal testing results and known
issues.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We weren't properly handling multicast on the mesh interface. Fix that,
which involves setting up the hardware to use the union of dev->mc_list
for both eth%d and msh%d devices.
This means we can't do it directly from ->set_multicast_list() because
we'd need to lock the other device to read its list, and we can't do
that because it might deadlock. So punt the actual work to keventd.
Also, invoke the same when taking an interface down; for some reason the
core calls ->set_multicast_list while IFF_UP is still set in dev->flags
when we're taking it down, so its addresses don't get removed then.
We also convert MAC_MULTICAST_ADR to a direct command while we're at it,
removing one more entry from the big switch statement in the deprecated
lbs_prepare_and_send_command() function.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the deprecated lbs_prepare_and_send_command() function for a
command which it doesn't understand is an error; complain loudly about
it even when we're not debugging.
The mesh stats bug, where we converted MESH_ACCESS to a direct command
but accidentally missed one user which was still trying to do it through
lbs_prepare_and_send_command(), would have been caught a lot quicker if
we'd done this sooner. Such bugs aren't entirely unlikely in future too,
as we convert more code to stop using this function.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix various problems:
- We converted MESH_ACCESS to a direct command but missed this caller.
- We were trying to access mesh stats even on meshless firmware.
- We should really zero the buffer if something goes wrong.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some network interfaces of the wireless drivers lack the 'device'
symlink in sysfs.
This patch lets the drivers create the links.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a fix for OLPC ticket #6586: "SCAN command fails, timer doesn't
fire". In fact, the timer was firing; the problem was that the dnld_sent
state variable was not being updated after the timer expired, so
lbs_execute_next_command was not being called.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes several problems I had:
* when removing the card while the card was scanning or associtating,
it could happen that destroy_workqueue() stuck and didn't return.
* make sure the command function doesn't run while we remove the list
of pending commands
* for still unknown reason, I had calls to lbs_stop_card() with
priv==NULL
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They don't return anything meaningfull and no-one cares about their results.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* make debug output match the variable name
* always report that lbs_remove_rtap() has has been exited
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to Coverity (kudo's to Adrian Bunk), we had one use-before-check
bug in libe libertas driver. This patch fixes this issue.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some command structs contain reserved or unused fields, which the driver
send uninitialized down to the card.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch (co-developed by Dan Williams and Holger Schurig) uses a kfifo
object for events and a swapping buffer scheme for the command response to
preserve the zero-copy semantics of the CF driver and keep memory usage low.
The main thread should only ever touch the buffer indexed by priv->resp_idx,
while the interface code is free to write to the second buffer, then swap
priv->resp_idx under the driver spinlock. The firmware specs only permit
one in-flight command, so there will only ever be one command response to
process at a time.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was used only at one place anyway.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
