Remove it, as it indirectly exposes netdev features. It's not used in
iproute2 (2.6.38) - is anything else using its interface?
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Results on dummy device can be seen in my netconf 2011
slides. These results are for a 10Gige IXGBE intel
nic - on another i5 machine, very similar specs to
the one used in the netconf2011 results.
It turns out - this is a hell lot worse than dummy
and so this patch is even more beneficial for 10G.
Test setup:
----------
System under test sending packets out.
Additional box connected directly dropping packets.
Installed prio qdisc on the eth device and default
netdev default length of 1000 used as is.
The 3 prio bands each were set to 100 (didnt factor in
the results).
5 packet runs were made and the middle 3 picked.
results
-------
The "cpu" column indicates the which cpu the sample
was taken on,
The "Pkt runx" carries the number of packets a cpu
dequeued when forced to be in the "dequeuer" role.
The "avg" for each run is the number of times each
cpu should be a "dequeuer" if the system was fair.
3.0-rc4 (plain)
cpu Pkt run1 Pkt run2 Pkt run3
================================================
cpu0 21853354 21598183 22199900
cpu1 431058 473476 393159
cpu2 481975 477529 458466
cpu3 23261406 23412299 22894315
avg 11506948 11490372 11486460
3.0-rc4 with patch and default weight 64
cpu Pkt run1 Pkt run2 Pkt run3
================================================
cpu0 13205312 13109359 13132333
cpu1 10189914 10159127 10122270
cpu2 10213871 10124367 10168722
cpu3 13165760 13164767 13096705
avg 11693714 11639405 11630008
As you can see the system is still not perfect but
is a lot better than what it was before...
At the moment we use the old backlog weight, weight_p
which is 64 packets. It seems to be reasonably fine
with that value.
The system could be made more fair if we reduce the
weight_p (as per my presentation), but we are going
to affect the shared backlog weight. Unless deemed
necessary, I think the default value is fine. If not
we could add yet another knob.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are enough instances of this:
iph->frag_off & htons(IP_MF | IP_OFFSET)
that a helper function is probably warranted.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).
To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.
Hope people are OK with tiny include file.
Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message size allocated for rtnl ifinfo dumps was limited to
a single page. This is not enough for additional interface info
available with devices that support SR-IOV and caused a bug in
which VF info would not be displayed if more than approximately
40 VFs were created per interface.
Implement a new function pointer for the rtnl_register service that will
calculate the amount of data required for the ifinfo dump and allocate
enough data to satisfy the request.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface uses a temporary buffer, but for no real reason.
And now can generate warnings like:
net/sched/sch_generic.c: In function dev_watchdog
net/sched/sch_generic.c:254:10: warning: unused variable drivername
Just return driver->name directly or "".
Reported-by: Connor Hansen <cmdkhh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit eeaeb068f1 (sch_sfq: allow big packets and be fair),
sfq_peek() can return a different skb that would be normally dequeued by
sfq_dequeue() [ if current slot->allot is negative ]
Use generic qdisc_peek_dequeued() instead of custom implementation, to
get consistent result.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Jesper Dangaard Brouer <hawk@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
While chasing a possible net_sched bug, I found that IP fragments have
litle chance to pass a congestioned SFQ qdisc :
- Say SFQ qdisc is full because one flow is non responsive.
- ip_fragment() wants to send two fragments belonging to an idle flow.
- sfq_enqueue() queues first packet, but see queue limit reached :
- sfq_enqueue() drops one packet from 'big consumer', and returns
NET_XMIT_CN.
- ip_fragment() cancel remaining fragments.
This patch restores fairness, making sure we return NET_XMIT_CN only if
we dropped a packet from the same flow.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Jamal Hadi Salim <hadi@cyberus.ca>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_deactivate_many() issues one synchronize_rcu() call after qdiscs set
to noop_qdisc.
This call is here to make sure they are no outstanding qdisc-less
dev_queue_xmit calls before returning to caller.
But in dismantle phase, we dont have to wait, because we wont activate
again the device, and we are going to wait one rcu grace period later in
rollback_registered_many().
After this patch, device dismantle uses one synchronize_net() and one
rcu_barrier() call only, so we have a ~30% speedup and a smaller RTNL
latency.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>,
CC: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
IP_ROUTE_CLASSID depends on INET and NET_CLS_ROUTE4 selects
IP_ROUTE_CLASSID, but when INET is not enabled, this kconfig warning
is produced, so fix it by making NET_CLS_ROUTE4 depend on INET.
warning: (NET_CLS_ROUTE4) selects IP_ROUTE_CLASSID which has unmet direct dependencies (NET && INET)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no callback of this module maybe queued
since we use kfree_rcu(), we can safely remove the rcu_barrier().
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
[PATCH 05/17] net,rcu: convert call_rcu(tcf_police_free_rcu) to kfree_rcu()
The rcu callback tcf_police_free_rcu() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(tcf_police_free_rcu).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The rcu callback tcf_common_free_rcu() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(tcf_common_free_rcu).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Add const qualifiers to structs iphdr, ipv6hdr and in6_addr pointers
where possible, to make code intention more obvious.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an implementation of the Quick Fair Queue scheduler developed
by Fabio Checconi. The same algorithm is already implemented in ipfw
in FreeBSD. Fabio had an earlier version developed on Linux, I just
cleaned it up. Thanks to Eric Dumazet for testing this under load.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only necessary parts are the src/dst addresses, the
interface indexes, the TOS, and the mark.
The rest is unnecessary bloat, which amounts to nearly
50 bytes on 64-bit.
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of various alignements [SLUB / qdisc], we use 512 bytes of
memory for one {p|b}fifo qdisc, instead of 256 bytes on 64bit arches and
192 bytes on 32bit ones.
Move the "u32 limit" inside "struct Qdisc" (no impact on other qdiscs)
Change qdisc_alloc(), first trying a regular allocation before an
oversized one.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Better document choke skb->cb[] use, like we did in netem and sfb
This adds a compile time check to make sure we dont exhaust skb->cb[]
space.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of debug message that are not useful, and enable
the log messages in case of error.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a patch originated with Stefano Salsano and Fabio Ludovici.
It provides several alternative loss models for use with netem.
This patch adds two state machine based loss models.
See: http://netgroup.uniroma2.it/twiki/bin/view.cgi/Main/NetemCLG
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many users have wanted the old functionality that was lost
to be able to use pfifo as inner qdisc for netem. The reason that
netem could not be classful with the older API was because of the
limitations of the old dequeue/requeue interface; now that qdisc API has
a peek function, there is no longer a problem with using any
inner qdisc's.
This reverts commit 0220146411.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than magic constant in code, expose the maximum size of
packet distribution table in API. In iproute2, q_netem defines
MAX_DIST as 16K already.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netem probability table can be large (up to 64K bytes)
which may be too large to allocate in one contiguous chunk.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use nla_put_nested to update netlink attribute value.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* make qdisc_ops local
* add sparse annotation about expected unlock/unlock in dump_class_stats
* fix indentation
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the Stochastic Fair Blue scheduler, based on work from :
W. Feng, D. Kandlur, D. Saha, K. Shin. Blue: A New Class of Active Queue
Management Algorithms. U. Michigan CSE-TR-387-99, April 1999.
http://www.thefengs.com/wuchang/blue/CSE-TR-387-99.pdf
This implementation is based on work done by Juliusz Chroboczek
General SFB algorithm can be found in figure 14, page 15:
B[l][n] : L x N array of bins (L levels, N bins per level)
enqueue()
Calculate hash function values h{0}, h{1}, .. h{L-1}
Update bins at each level
for i = 0 to L - 1
if (B[i][h{i}].qlen > bin_size)
B[i][h{i}].p_mark += p_increment;
else if (B[i][h{i}].qlen == 0)
B[i][h{i}].p_mark -= p_decrement;
p_min = min(B[0][h{0}].p_mark ... B[L-1][h{L-1}].p_mark);
if (p_min == 1.0)
ratelimit();
else
mark/drop with probabilty p_min;
I did the adaptation of Juliusz code to meet current kernel standards,
and various changes to address previous comments :
http://thread.gmane.org/gmane.linux.network/90225http://thread.gmane.org/gmane.linux.network/90375
Default flow classifier is the rxhash introduced by RPS in 2.6.35, but
we can use an external flow classifier if wanted.
tc qdisc add dev $DEV parent 1:11 handle 11: \
est 0.5sec 2sec sfb limit 128
tc filter add dev $DEV protocol ip parent 11: handle 3 \
flow hash keys dst divisor 1024
Notes:
1) SFB default child qdisc is pfifo_fast. It can be changed by another
qdisc but a child qdisc MUST not drop a packet previously queued. This
is because SFB needs to handle a dequeued packet in order to maintain
its virtual queue states. pfifo_head_drop or CHOKe should not be used.
2) ECN is enabled by default, unlike RED/CHOKe/GRED
With help from Patrick McHardy & Andi Kleen
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Juliusz Chroboczek <Juliusz.Chroboczek@pps.jussieu.fr>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Andi Kleen <andi@firstfloor.org>
CC: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable _data is used in asm-generic to define sections
which causes sparse warnings, so just rename the variable.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Eric W. Biederman <ebiederm@xmission.com>
In the beginning with batching unreg_list was a list that was used only
once in the lifetime of a network device (I think). Now we have calls
using the unreg_list that can happen multiple times in the life of a
network device like dev_deactivate and dev_close that are also using the
unreg_list. In addition in unregister_netdevice_queue we also do a
list_move because for devices like veth pairs it is possible that
unregister_netdevice_queue will be called multiple times.
So I think the change below to fix dev_deactivate which Eric D. missed
will fix this problem. Now to go test that.
Signed-off-by: David S. Miller <davem@davemloft.net>
All the cleanup code in mqprio_destroy() is currently conditional on
priv->qdiscs being non-null, but that condition should only apply to
the per-queue qdisc cleanup. We should always set the number of
traffic classes back to 0 here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
CHOKe ("CHOose and Kill" or "CHOose and Keep") is an alternative
packet scheduler based on the Random Exponential Drop (RED) algorithm.
The core idea is:
For every packet arrival:
Calculate Qave
if (Qave < minth)
Queue the new packet
else
Select randomly a packet from the queue
if (both packets from same flow)
then Drop both the packets
else if (Qave > maxth)
Drop packet
else
Admit packet with proability p (same as RED)
See also:
Rong Pan, Balaji Prabhakar, Konstantinos Psounis, "CHOKe: a stateless active
queue management scheme for approximating fair bandwidth allocation",
Proceeding of INFOCOM'2000, March 2000.
Help from:
Eric Dumazet <eric.dumazet@gmail.com>
Patrick McHardy <kaber@trash.net>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to allow divisor to be a parameter (in 2.6.38-rc1)
commit 817fb15dfd
introduced a possible deadlock caught by sparse.
The scheduler tree lock was left locked in the case of an incorrect
divisor value. Simplest fix is to move test outside of lock
which also solves problem of partial update.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mqprio_dump() should make sure all fields of struct tc_mqprio_qopt are
initialized.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now qdisc stab is handled before TCQ_F_CAN_BYPASS test in
__dev_xmit_skb(), we can generalize TCQ_F_CAN_BYPASS to other qdiscs
than pfifo_fast : pfifo, bfifo, pfifo_head_drop and sfq
SFQ is special because it can have external classifiers, and in these
cases, we cannot bypass queue discipline (packet could be dropped by
classifier) without admin asking it, or further changes.
Its worth doing this, especially for SFQ, avoiding dirtying memory in
case no packets are already waiting in queue.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 44b8288308 (net_sched: pfifo_head_drop problem), we fixed
a problem with pfifo_head drops that incorrectly decreased
sch->bstats.bytes and sch->bstats.packets
Several qdiscs (CHOKe, SFQ, pfifo_head, ...) are able to drop a
previously enqueued packet, and bstats cannot be changed, so
bstats/rates are not accurate (over estimated)
This patch changes the qdisc_bstats updates to be done at dequeue() time
instead of enqueue() time. bstats counters no longer account for dropped
frames, and rates are more correct, since enqueue() bursts dont have
effect on dequeue() rate.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts stab qdisc management to RCU, so that we can perform
the qdisc_calculate_pkt_len() call before getting qdisc lock.
This shortens the lock's held time in __dev_xmit_skb().
This permits more qdiscs to get TCQ_F_CAN_BYPASS status, avoiding lot of
cache misses and so reducing latencies.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Jesper Dangaard Brouer <hawk@diku.dk>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Jamal Hadi Salim <hadi@cyberus.ca>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 3711210576 (net: QDISC_STATE_RUNNING dont need atomic bit
ops) I moved QDISC_STATE_RUNNING flag to __state container, located in
the cache line containing qdisc lock and often dirtied fields.
I now move TCQ_F_THROTTLED bit too, so that we let first cache line read
mostly, and shared by all cpus. This should speedup HTB/CBQ for example.
Not using test_bit()/__clear_bit()/__test_and_set_bit allows to use an
"unsigned int" for __state container, reducing by 8 bytes Qdisc size.
Introduce helpers to hide implementation details.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Jesper Dangaard Brouer <hawk@diku.dk>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Jamal Hadi Salim <hadi@cyberus.ca>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFQ currently uses a 1024 slots hash table, and its internal structure
(sfq_sched_data) allocation needs order-1 page on x86_64
Allow tc command to specify a divisor value (hash table size), between 1
and 65536.
If no value is provided, assume the 1024 default size.
This allows admins to setup smaller (or bigger) SFQ for specific needs.
This also brings back sfq_sched_data allocations to order-0 ones, saving
3KB per SFQ qdisc.
Jesper uses ~55.000 SFQ in one machine, this patch should free 165 MB of
memory.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Jesper Dangaard Brouer <hawk@diku.dk>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Jamal Hadi Salim <hadi@cyberus.ca>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup net/sched code to current CodingStyle and practices.
Reduce inline abuse
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements a mqprio queueing discipline that by default creates
a pfifo_fast qdisc per tx queue and provides the needed configuration
interface.
Using the mqprio qdisc the number of tcs currently in use along
with the range of queues alloted to each class can be configured. By
default skbs are mapped to traffic classes using the skb priority.
This mapping is configurable.
Configurable parameters,
struct tc_mqprio_qopt {
__u8 num_tc;
__u8 prio_tc_map[TC_BITMASK + 1];
__u8 hw;
__u16 count[TC_MAX_QUEUE];
__u16 offset[TC_MAX_QUEUE];
};
Here the count/offset pairing give the queue alignment and the
prio_tc_map gives the mapping from skb->priority to tc.
The hw bit determines if the hardware should configure the count
and offset values. If the hardware bit is set then the operation
will fail if the hardware does not implement the ndo_setup_tc
operation. This is to avoid undetermined states where the hardware
may or may not control the queue mapping. Also minimal bounds
checking is done on the count/offset to verify a queue does not
exceed num_tx_queues and that queue ranges do not overlap. Otherwise
it is left to user policy or hardware configuration to create
useful mappings.
It is expected that hardware QOS schemes can be implemented by
creating appropriate mappings of queues in ndo_tc_setup().
One expected use case is drivers will use the ndo_setup_tc to map
queue ranges onto 802.1Q traffic classes. This provides a generic
mechanism to map network traffic onto these traffic classes and
removes the need for lower layer drivers to know specifics about
traffic types.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
GRETH: resolve SMP issues and other problems
GRETH: handle frame error interrupts
GRETH: avoid writing bad speed/duplex when setting transfer mode
GRETH: fixed skb buffer memory leak on frame errors
GRETH: GBit transmit descriptor handling optimization
GRETH: fix opening/closing
GRETH: added raw AMBA vendor/device number to match against.
cassini: Fix build bustage on x86.
e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
e1000e: update Copyright for 2011
e1000: Avoid unhandled IRQ
r8169: keep firmware in memory.
netdev: tilepro: Use is_unicast_ether_addr helper
etherdevice.h: Add is_unicast_ether_addr function
ks8695net: Use default implementation of ethtool_ops::get_link
ks8695net: Disable non-working ethtool operations
USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable.
vxge: Remember to release firmware after upgrading firmware
netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr
ipsec: update MAX_AH_AUTH_LEN to support sha512
...
Fix dependencies of netfilter realm match: it depends on NET_CLS_ROUTE,
which itself depends on NET_SCHED; this dependency is missing from netfilter.
Since matching on realms is also useful without having NET_SCHED enabled and
the option really only controls whether the tclassid member is included in
route and dst entries, rename the config option to IP_ROUTE_CLASSID and move
it outside of traffic scheduling context to get rid of the NET_SCHED dependeny.
Reported-by: Vladis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
After recent changes, (percpu stats on vlan/tunnels...), we dont need
anymore per struct netdev_queue tx_bytes/tx_packets/tx_dropped counters.
Only remaining users are ixgbe, sch_teql, gianfar & macvlan :
1) ixgbe can be converted to use existing tx_ring counters.
2) macvlan incremented txq->tx_dropped, it can use the
dev->stats.tx_dropped counter.
3) sch_teql : almost revert ab35cd4b8f (Use net_device internal stats)
Now we have ndo_get_stats64(), use it, even for "unsigned long"
fields (No need to bring back a struct net_device_stats)
4) gianfar adds a stats structure per tx queue to hold
tx_bytes/tx_packets
This removes a lockdep warning (and possible lockup) in rndis gadget,
calling dev_get_stats() from hard IRQ context.
Ref: http://www.spinics.net/lists/netdev/msg149202.html
Reported-by: Neil Jones <neiljay@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HTB takes into account skb is segmented in stats updates.
Generalize this to all schedulers.
They should use qdisc_bstats_update() helper instead of manipulating
bstats.bytes and bstats.packets
Add bstats_update() helper too for classes that use
gnet_stats_basic_packed fields.
Note : Right now, TCQ_F_CAN_BYPASS shortcurt can be taken only if no
stab is setup on qdisc.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 57dbb2d83d (sched: add head drop fifo queue)
introduced pfifo_head_drop, and broke the invariant that
sch->bstats.bytes and sch->bstats.packets are COUNTER (increasing
counters only)
This can break estimators because est_timer() handles unsigned deltas
only. A decreasing counter can then give a huge unsigned delta.
My mid term suggestion would be to change things so that
sch->bstats.bytes and sch->bstats.packets are incremented in dequeue()
only, not at enqueue() time. We also could add drop_bytes/drop_packets
and provide estimations of drop rates.
It would be more sensible anyway for very low speeds, and big bursts.
Right now, if we drop packets, they still are accounted in byte/packets
abolute counters and rate estimators.
Before this mid term change, this patch makes pfifo_head_drop behavior
similar to other qdiscs in case of drops :
Dont decrement sch->bstats.bytes and sch->bstats.packets
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide child qdisc backlog (byte count) information so that "tc -s
qdisc" can report it to user.
packet count is already correctly provided.
qdisc red 11: parent 1:11 limit 60Kb min 15Kb max 45Kb ecn
Sent 3116427684 bytes 1415782 pkt (dropped 8, overlimits 7866 requeues 0)
rate 242385Kbit 13630pps backlog 13560b 8p requeues 0
marked 7865 early 1 pdrop 7 other 0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
slot_dequeue_head() should make sure slot skb chain is correct in both
ways, or we can crash if all possible flows are in use.
Jarek pointed out slot_queue_init() can now be done in sfq_init() once,
instead each time a flow is setup.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFQ is currently 'limited' to small packets, because it uses a 15bit
allotment number per flow. Introduce a scale by 8, so that we can handle
full size TSO/GRO packets.
Use appropriate handling to make sure allot is positive before a new
packet is dequeued, so that fairness is respected.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jarek Poplawski <jarkao2@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
sfq_walk() runs without qdisc lock. By the time it selects a non empty
hash slot and sfq_dump_class_stats() is run (with lock held), slot might
have been freed : We then access q->slots[SFQ_EMPTY_SLOT], out of
bounds, and crash in slot_queue_walk()
On previous kernels, bug is here but out of bounds qs[SFQ_DEPTH] and
allot[SFQ_DEPTH] are located in struct sfq_sched_data, so no illegal
memory access happens, only possibly wrong data reported to user.
Also, slot_dequeue_tail() should make sure slot skb chain is correctly
terminated, or sfq_dump_class_stats() can access freed skbs.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
Here is a respin of patch.
I'll send a short patch to make SFQ more fair in presence of large
packets as well.
Thanks
[PATCH v3 net-next-2.6] net_sched: sch_sfq: better struct layouts
This patch shrinks sizeof(struct sfq_sched_data)
from 0x14f8 (or more if spinlocks are bigger) to 0x1180 bytes, and
reduce text size as well.
text data bss dec hex filename
4821 152 0 4973 136d old/net/sched/sch_sfq.o
4627 136 0 4763 129b new/net/sched/sch_sfq.o
All data for a slot/flow is now grouped in a compact and cache friendly
structure, instead of being spreaded in many different points.
struct sfq_slot {
struct sk_buff *skblist_next;
struct sk_buff *skblist_prev;
sfq_index qlen; /* number of skbs in skblist */
sfq_index next; /* next slot in sfq chain */
struct sfq_head dep; /* anchor in dep[] chains */
unsigned short hash; /* hash value (index in ht[]) */
short allot; /* credit for this slot */
};
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jarek Poplawski <jarkao2@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deploying SFQ/IFB here at work, I found the allot management was
pretty wrong in sfq, even changing allot from short to int...
We should init allot for each new flow, not using a previous value found
in slot.
Before patch, I saw bursts of several packets per flow, apparently
denying the default "quantum 1514" limit I had on my SFQ class.
class sfq 11:1 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 7p requeues 0
allot 11546
class sfq 11:46 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 1p requeues 0
allot -23873
class sfq 11:78 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 5p requeues 0
allot 11393
After patch, better fairness among each flow, allot limit being
respected, allot is positive :
class sfq 11:e parent 11:
(dropped 0, overlimits 0 requeues 86)
backlog 0b 3p requeues 86
allot 596
class sfq 11:94 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 3p requeues 0
allot 1468
class sfq 11:a4 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 4p requeues 0
allot 650
class sfq 11:bb parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 3p requeues 0
allot 596
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently return for each active SFQ slot the number of packets in
queue. We can also give number of bytes accounted for these packets.
tc -s class show dev ifb0
Before patch :
class sfq 11:3d9 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 3p requeues 0
allot 1266
After patch :
class sfq 11:3e4 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 4380b 3p requeues 0
allot 1212
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dev_close_many and dev_deactivate_many to factorize another
sync-rcu operation on the netdevice unregister path.
$ modprobe dummy numdummies=10000
$ ip link set dev dummy* up
$ time rmmod dummy
Without the patch With the patch
real 0m 24.63s real 0m 5.15s
user 0m 0.00s user 0m 0.00s
sys 0m 6.05s sys 0m 5.14s
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate qdisc memory according to NUMA properties of cpus included in
xps map.
To be effective, qdisc should be (re)setup after changes
of /sys/class/net/eth<n>/queues/tx-<n>/xps_cpus
I added a numa_node field in struct netdev_queue, containing NUMA node
if all cpus included in xps_cpus share same node, else -1.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing struct netdev_queue state against FROZEN bit, we also test
XOFF bit. We can test both bits at once and save some cycles.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the documentation refers to web pages under
the domain `osdl.org'. However, `osdl.org' now
redirects to `linuxfoundation.org'.
Rather than rely on redirections, this patch updates
the addresses appropriately; for the most part, only
documentation that is meant to be current has been
updated.
The patch should be pretty quick to scan and check;
each new web-page url was gotten by trying out the
original URL in a browser and then simply copying the
the redirected URL (formatting as necessary).
There is some conflict as to which one of these domain
names is preferred:
linuxfoundation.org
linux-foundation.org
So, I wrote:
info@linuxfoundation.org
and got this reply:
Message-ID: <4CE17EE6.9040807@linuxfoundation.org>
Date: Mon, 15 Nov 2010 10:41:42 -0800
From: David Ames <david@linuxfoundation.org>
...
linuxfoundation.org is preferred. The canonical name for our web site is
www.linuxfoundation.org. Our list site is actually
lists.linux-foundation.org.
Regarding email linuxfoundation.org is preferred there are a few people
who choose to use linux-foundation.org for their own reasons.
Consequently, I used `linuxfoundation.org' for web pages and
`lists.linux-foundation.org' for mailing-list web pages and email addresses;
the only personal email address I updated from `@osdl.org' was that of
Andrew Morton, who prefers `linux-foundation.org' according `git log'.
Signed-off-by: Michael Witten <mfwitten@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The basic classifier keeps statistics but does not report it to user space.
This showed up when using basic classifier (with police) as a default catch
all on ingress; no statistics were reported.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somewhere along the lines net_cls_subsys_id became a macro when
cls_cgroup is built as a module. Not only did it make cls_cgroup
completely useless, it also causes it to crash on module unload.
This patch fixes this by removing that macro.
Thanks to Eric Dumazet for diagnosing this problem.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While validating the configuration em_ops is already set, thus the
individual destroy functions are called, but the ematch data has
not been allocated and associated with the ematch yet.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
The first parameter dev isn't in use in qdisc_create_dflt().
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Zijlstra found a bug in the way softirq time is accounted in
VIRT_CPU_ACCOUNTING on this thread:
http://lkml.indiana.edu/hypermail//linux/kernel/1009.2/01366.html
The problem is, softirq processing uses local_bh_disable internally. There
is no way, later in the flow, to differentiate between whether softirq is
being processed or is it just that bh has been disabled. So, a hardirq when bh
is disabled results in time being wrongly accounted as softirq.
Looking at the code a bit more, the problem exists in !VIRT_CPU_ACCOUNTING
as well. As account_system_time() in normal tick based accouting also uses
softirq_count, which will be set even when not in softirq with bh disabled.
Peter also suggested solution of using 2*SOFTIRQ_OFFSET as irq count
for local_bh_{disable,enable} and using just SOFTIRQ_OFFSET while softirq
processing. The patch below does that and adds API in_serving_softirq() which
returns whether we are currently processing softirq or not.
Also changes one of the usages of softirq_count in net/sched/cls_cgroup.c
to in_serving_softirq.
Looks like many usages of in_softirq really want in_serving_softirq. Those
changes can be made individually on a case by case basis.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1286237003-12406-2-git-send-email-venki@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a seqlock in struct neighbour to protect neigh->ha[], and avoid
dirtying neighbour in stress situation (many different flows / dsts)
Dirtying takes place because of read_lock(&n->lock) and n->used writes.
Switching to a seqlock, and writing n->used only on jiffies changes
permits less dirtying.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_headroom() is unsigned so "skb_headroom(skb) + toff" is also
unsigned and can't be less than zero. This test was added in 66d50d25:
"u32: negative offset fix" It was supposed to fix a regression.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ingress being not used very much, and net_device->ingress_queue being
quite a big object (128 or 256 bytes), use a dynamic allocation if
needed (tc qdisc add dev eth0 ingress ...)
dev_ingress_queue(dev) helper should be used only with RTNL taken.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is some confusion with rx_queue name after RPS, and net drivers
private rx_queue fields.
I suggest to rename "struct net_device"->rx_queue to ingress_queue.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list_head conversion unearther an unnecessary flow
check. Since flow is always NULL here we don't need to
see if a matching flow exists already.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes init_vf() function, so on each new backlog period parent's
cl_cfmin is properly updated (including further propgation towards the root),
even if the activated leaf has no upperlimit curve defined.
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reviewing commit 1c40be12f7, I
audited other users of tc_action_ops->dump for information leaks.
That commit covered almost all of them but act_police still had a leak.
opt.limit and opt.capab aren't zeroed out before the structure is
passed out.
This patch uses the C99 initializers to zero everything unused out.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial extension to existing meta data match rules to allow
matching on skb receive hash value.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
