Reduce the eDP detection to just checking if it's port A, or if
the VBT tells us that the port is eDP for the other ports.
Suggested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV can have eDP on either port B or C, or even both. Based on the
VBT spec, intel_dpd_is_edp() should work on VLV too, assuming we
check the correct ports.
So instead of hardcoding port D, rename the function to
intel_dp_is_edp() and pass the port as a parameter, and use it
on VLV ports B and C.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71051
Tested-by: Robert Hooker <robert.hooker@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Wrestle the patch to apply and compile properly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We used to put the local sink and any downstream sinks to power down
mode at disable or dpms off using the DPCD SET_POWER register, until
this was broken by
commit e8cb455876
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jul 1 13:05:48 2012 +0200
drm/i915/dp: convert to encoder disable/enable
Fix it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So here's the Broadwell pull request. From a kernel driver pov there's
two areas with big changes in Broadwell:
- Completely new enumerated interrupt bits. On the plus side it now looks
fairly unform and sane.
- Completely new pagetable layout.
To ensure minimal impact on existing platforms we've refactored both the
irq and low-level gtt handling code a lot in anticipation of the bdw push.
So now bdw enabling in these areas just plugs in a bunch of vfuncs.
Otherwise it's all fairly harmless adjusting of switch cases and
if-ladders to shovel bdw into the right blocks. So minimized impact on
existing platforms. I've also merged the bdw-stage1 branch into our
-nightly integration branch for the past week to make sure we don't break
anything.
Note that there's still quite a flurry or patches floating around, but
I've figured I'll push this out. I plan to keep the bdw fixes separate
from my usual -fixes stream so that you can reject them easily in case it
still looks like too much churn. Also, bdw is for now hidden behind the
preliminary hw enabling module option. So there's no real pressure to get
follow-up patches all into 3.13.
* tag 'bdw-stage1-2013-11-08-v2' of git://people.freedesktop.org/~danvet/drm-intel: (75 commits)
drm/i915: Mask the vblank interrupt on bdw by default
drm/i915: Wire up cpu fifo underrun reporting support for bdw
drm/i915: Optimize gen8_enable|disable_vblank functions
drm/i915: Wire up pipe CRC support for bdw
drm/i915: Wire up PCH interrupts for bdw
drm/i915: Wire up port A aux channel
drm/i915: Fix up the bdw pipe interrupt enable lists
drm/i915: Optimize pipe irq handling on bdw
drm/i915/bdw: Take render error interrupt out of the mask
drm/i915/bdw: Add BDW PCH check first
drm/i915: Use hsw_crt_get_config on BDW
drm/i915/bdw: Change dp aux timeout to 600us on DDIA
drm/i915/bdw: Enable trickle feed on Broadwell
drm/i915/bdw: WaSingleSubspanDispatchOnAALinesAndPoints
drm/i915/bdw: conservative SBE VUE cache mode
drm/i915/bdw: Limit SDE poly depth FIFO to 2
drm/i915/bdw: Sampler power bypass disable
ddrm/i915/bdw: Disable centroid pixel perf optimization
drm/i915/bdw: BWGTLB clock gate disable
drm/i915/bdw: Implement edp PSR workarounds
...
Broadwell PSR support is a superset of Haswell. With this simple
register base calculation, everything that worked on HSW for eDP PSR
should work on BDW.
Note that Broadwell provides additional PSR support. This is not
addressed at this time.
v2: Make the HAS_PSR include BDW
v3: Use the correct offset (I had incorrectly used one from my faulty
brain) (Art!)
v4: It helps if you git add
v5: Be explicit about not setting min link entry time for BDW. This
should be no functional change over v4 (Jani)
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They're not the same as the Haswell ones.
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bit a bit -fixes pull request in the merge window than usual dua to two
feauture-y things:
- Display CRCs are now enabled on all platforms, including the odd DP case
on gm45/vlv. Since this is a testing-only feature it should ever hurt,
but I figured it'll help with regression-testing -fixes. So I left it
in and didn't postpone it to 3.14.
- Display power well refactoring from Imre. Would have caused major pain
conflict with the bdw stage 1 patches if I'd postpone this to -next.
It's only an relatively small interface rework, so shouldn't cause pain.
It's also been in my tree since almost 3 weeks already.
That accounts for about two thirds of the pull, otherwise just bugfixes:
- vlv backlight fix from Jesse/Jani
- vlv vblank timestamp fix from Jesse
- improved edp detection through vbt from Ville (fixes a vlv issue)
- eDP vdd fix from Paulo
- fixes for dvo lvds on i830M
- a few smaller things all over
Note: This contains a backmerge of v3.12. Since the -internal branch
always applied on top of -nightly I need that unified base to merge bdw
patches. So you'll get a conflict with radeon connector props when pulling
this (and nouveau/master will also conflict a bit when Ben doesn't
rebase). The backmerge itself only had conflicts in drm/i915.
There's also a tiny conflict between Jani's backlight fix and your sysfs
lifetime fix in drm-next.
* tag 'drm-intel-fixes-2013-11-07' of git://people.freedesktop.org/~danvet/drm-intel: (940 commits)
drm/i915/vlv: use per-pipe backlight controls v2
drm/i915: make backlight functions take a connector
drm/i915: move opregion asle request handling to a work queue
drm/i915/vlv: use PIPE_START_VBLANK interrupts on VLV
drm/i915: Make intel_dp_is_edp() less specific
drm/i915: Give names to the VBT child device type bits
drm/i915/vlv: enable HDA display audio for Valleyview2
drm/i915/dvo: call ->mode_set callback only when the port is running
drm/i915: avoid unclaimed registers when capturing the error state
drm/i915: Enable DP port CRC for the "auto" source on g4x/vlv
drm/i915: scramble reset support for DP port CRC on vlv
drm/i915: scramble reset support for DP port CRC on g4x
drm/i916: add "auto" pipe CRC source
...
Conflicts:
MAINTAINERS
drivers/gpu/drm/i915/intel_panel.c
drivers/gpu/drm/nouveau/core/subdev/mc/base.c
drivers/gpu/drm/radeon/atombios_encoders.c
drivers/gpu/drm/radeon/radeon_connectors.c
On VLV/BYT, backlight controls a per-pipe, so when adjusting the
backlight we need to pass the correct info. So make the externally
visible backlight functions take a connector argument, which can be used
internally to figure out the pipe backlight to adjust.
v2: make connector pipe lookup check for NULL crtc (Jani)
fixup connector check in ASLE code (Jani)
v3: make sure we take the mode config lock around lookups (Daniel)
v4: fix double unlock in panel_get_brightness (Daniel)
v5: push ASLE work into a work queue (Daniel)
v6: separate ASLE work to a prep patch, rebase (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the bits in the VBT child device type have some speciifc meaning,
so looking for an exact match isn't always the right thing. On some
VLVs for example the device type for eDP panels is 0x1806.
If we mask out the bits that could concievably change between different
eDP panels, we are left with the set of bits that should still
tell us if the port is eDP or not.
v2: Use the named bits for VBT child device type
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71051
Tested-by: Robert Hooker <robert.hooker@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I want to merge in the new Broadwell support as a late hw enabling
pull request. But since the internal branch was based upon our
drm-intel-nightly integration branch I need to resolve all the
oustanding conflicts in drm/i915 with a backmerge to make the 60+
patches apply properly.
We'll propably have some fun because Linus will come up with a
slightly different merge solution.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_crt.c
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_drv.h
All rather simple adjacent lines changed or partial backports from
-next to -fixes, with the exception of the thaw code in i915_dma.c.
That one needed a bit of shuffling to restore the intent.
Oh and the massive header file reordering in intel_drv.h is a bit
trouble. But not much.
v2: Also don't forget the fixup for the silent conflict that results
in compile fail ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That explains why I was seeing 2 consecutive "Turning eDP VDD off"
messages.
Regression introduced by:
commit bf13e81b90
Author: Jani Nikula <jani.nikula@intel.com>
Date: Fri Sep 6 07:40:05 2013 +0300
drm/i915: add support for per-pipe power sequencing on vlv
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now we only print messages when we actually enable VDD and when we
actually disable VDD.
The changes in the last commit triggered a big number of messages
while the driver was being initialized, and I thought we were toggling
things on/off too many times, but that was not really true: we were
just being too verbose.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the eDP output is disabled, then we try to use /dev/i2c-X file to
do i2c transations, we get a WARN from intel_dp_check_edp() saying
we're trying to do AUX communication with the panel off. So this
commit reorganizes the code so we enable the VDD at
intel_dp_i2c_aux_ch() instead of just the callers inside i915.ko.
This fixes the i2c subtest from the pc8 test of intel-gpu-tools on
machines that have eDP panels.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This isn't a real fix to the problem, but rather a stopgap measure while
trying to find a proper solution.
There are several laptops out there that fail to light up the eDP panel
in UEFI boot mode. They seem to be mostly IVB machines, including but
apparently not limited to Dell XPS 13, Asus TX300, Asus UX31A, Asus
UX32VD, Acer Aspire S7. They seem to work in CSM or legacy boot.
The difference between UEFI and CSM is that the BIOS provides a
different VBT to the kernel. The UEFI VBT typically specifies 18 bpp and
1.62 GHz link for eDP, while CSM VBT has 24 bpp and 2.7 GHz link. We end
up clamping to 18 bpp in UEFI mode, which we can fit in the 1.62 Ghz
link, and for reasons yet unknown fail to light up the panel.
Dithering from 24 to 18 bpp itself seems to work; if we use 18 bpp with
2.7 GHz link, the eDP panel lights up. So essentially this is a link
speed issue, and *not* a bpp clamping issue.
The bug raised its head since
commit 657445fe86
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat May 4 10:09:18 2013 +0200
Revert "drm/i915: revert eDP bpp clamping code changes"
which started clamping bpp *before* computing the link requirements, and
thus affecting the required bandwidth. Clamping after the computations
kept the link at 2.7 GHz.
Even though the BIOS tells us to use 18 bpp through the VBT, it happily
boots up at 24 bpp and 2.7 GHz itself! Use this information to
selectively ignore the VBT provided value.
We can't ignore the VBT eDP bpp altogether, as there are other laptops
that do require the clamping to be used due to EDID reporting higher bpp
than the panel can support.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59841
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67950
Tested-by: Ulf Winkelvos <ulf@winkelvos.de>
Tested-by: jkp <jkp@iki.fi>
CC: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- CRC support from Damien and He Shuang. Long term this should allow us to
test an awful lot modesetting corner cases automatically. So for me as
the maintainer this is really big.
- HDMI audio fix from Jani.
- VLV dpll computation code refactoring from Ville.
- Fixups for the gpu booster from last time around (Chris).
- Some cleanups in the context code from Ben.
- More watermark work from Ville (we'll be getting there ...).
- vblank timestamp improvements from Ville.
- CONFIG_FB=n support, including drm core changes to make the fbdev
helpers optional.
- DP link training improvements (Jani).
- mmio vtable from Ben, prep work for future hw.
* tag 'drm-intel-next-2013-10-18' of git://people.freedesktop.org/~danvet/drm-intel: (132 commits)
drm/i915/dp: don't mention eDP bpp clamping if it doesn't affect bpp
drm/i915: remove dead code in ironlake_crtc_mode_set
drm/i915: crc support for hsw
drm/i915: fix CRC debugfs setup
drm/i915: wait one vblank when disabling CRCs
drm/i915: use ->get_vblank_counter for the crc frame counter
drm/i915: wire up CRC interrupt for ilk/snb
drm/i915: add CRC #defines for ilk/snb
drm/i915: extract display_pipe_crc_update
drm/i915: don't Oops in debugfs for I915_FBDEV=n
drm/i915: set HDMI pixel clock in audio configuration
drm/i915: pass mode to ELD write vfuncs
cpufreq: Add dummy cpufreq_cpu_get/put for CONFIG_CPU_FREQ=n
drm/i915: check gem bo size when creating framebuffers
drm/i915: Use unsigned long for obj->user_pin_count
drm/i915: prevent tiling changes on framebuffer backing storage
drm/i915: grab dev->struct_mutex around framebuffer_init
drm/i915: vlv: fix VGA hotplug after modeset
drm: add support for additional stereo 3D modes
drm/i915: preserve dispaly init order on ByT
...
So drm was abusing device lifetimes, by having embedded device structures
in the minor and connector it meant that the lifetime of the internal drm
objects (drm_minor and drm_connector) were tied to the lifetime of the device
files in sysfs, so if something kept those files opened the current code
would kfree the objects and things would go downhill from there.
Now in reality there is no need for these lifetimes to be so intertwined,
especailly with hotplugging of devices where we wish to remove the sysfs
and userspace facing pieces before we can unwind the internal objects due
to open userspace files or mmaps, so split the objects out so the struct
device is no longer embedded and do what fbdev does and just allocate
and remove the sysfs inodes separately.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is useful with the follow-up patch that frobs
dev_priv->vbt.edp_bpp, and the value no longer comes directly from
VBT.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DP spec allows this, and requires it when full link training is
started with non-minimum voltage swing and/or non-zero pre-emphasis.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If channel equalization succeeds, there's no indication something went
wrong in clock recovery (unless debug is enabled). We should shout about
the failures and fix them instead of hiding them under the carpet.
This has allowed bugs like [1] stay dormant for a long time.
[1] https://bugs.freedesktop.org/show_bug.cgi?id=70117
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The conflict in intel_drv.h tripped me up a bit since a patch in dinq
moves all the functions around, but another one in drm-next removes a
single function. So I'ev figured backing this into a backmerge would
be good.
i915_dma.c is just adjacent lines changed, nothing nefarious there.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/intel_drv.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not really needed, rather just adds another place to hold
intermediate values that could go wrong, and it's not clear that the
training pattern set or training lane set should be written at this
point at all.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
for igt test case.
v2: remove trailing spaces and fix conflicts
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet:
- make it comipile
- s/IS_HASWELL/HAS_PSR/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Power Well in use forces constantly PSR to exit.
On recent Kernel I noticed that PSR Performance Counter was always 0
indicating that PSR was never really achieved.
By masking LPSP, PSR can work normally and save power on Haswell.
Two bugs had been raised with PSR flag enabled:
- "Screen flickers when booted by enabling PSR in the kernel (i915.enable_psr=1) , the system is booting to a gray screen."
- "When booting the DUT with PSR feature enabled in the kernel (i915.enable_psr=1) , the system is booting to a gray screen."
Both bugs has been fixed by this patch.
v2: proper comment for -fixes
Tested-by: Selvaraj, Elavarasan <elavarasanx.selvaraj@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For some reason, every single time I try to run module_reload
something tries to read the connector sysfs files. This happens
after we destroy the encoders and before we destroy the connectors, so
when the sysfs read triggers the connector detect() function,
intel_conector->encoder points to memory that was already freed.
The bad backtrace is just:
[<ffffffff8163ca9a>] dump_stack+0x54/0x74
[<ffffffffa00c2c8e>] intel_dp_detect+0x1e/0x4b0 [i915]
[<ffffffffa001913d>] status_show+0x3d/0x80 [drm]
[<ffffffff813d5340>] dev_attr_show+0x20/0x60
[<ffffffff81221f50>] ? sysfs_read_file+0x80/0x1b0
[<ffffffff81221f79>] sysfs_read_file+0xa9/0x1b0
[<ffffffff811aaf1e>] vfs_read+0x9e/0x170
[<ffffffff811aba4c>] SyS_read+0x4c/0xa0
[<ffffffff8164e392>] system_call_fastpath+0x16/0x1b
But if you add tons of memory checking debug options to your Kernel
you'll also see:
- general protection fault: 0000
- BUG kmalloc-4096 (Tainted: G D W ): Poison overwritten
- INFO: Allocated in intel_ddi_init+0x65/0x270 [i915]
- INFO: Freed in intel_dp_encoder_destroy+0x69/0xb0 [i915]
Among a bunch of other error messages.
So this commit just destroys the sysfs files before both the encoder
and connectors are freed.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Neither the DP spec nor the compliance test spec state or imply that we
should write the DP_TRAINING_PATTERN_SET at every voltage swing and
pre-emphasis change. Indeed we probably shouldn't. So don't.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49402
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Smoke-tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Per DP1.2 spec.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
struct drm_mode_display now has a separate crtc_ version of the clock to
be used when we're talking about the timings given to the harwadre (was
far as the mode is concerned).
This commit is really the result of a git grep adjusted_mode.*clock and
replacing those by adjusted_mode.crtc_clock. No functional change.
v2: Rebased on drm-intel-queued-next
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the typo in previous commit for DP 1.62 divisor.
drm/i915: Move Valleyview DP DPLL divisor calc to intel_dp_set_clock v2
v2: sigh, the m1 div is 3.
Reported-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Future generations will be changing these registers (thanks to design
for giving us an early heads up). To help abstract, create the
definition of the base of the register block, and define all registers
relative to that.
Design has promised to not change the offsets relative to the base.
v2: Also change IS_HASWELL checks to HAS_PSR
CC: Rodrigo Vivi <rodrigo.vivi@gmail.com>
CC: Intel GFX <intel-gfx@lists.freedesktop.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reduce AUX transactions for non-eDP.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently treat the child_device_config as a simple struct, but
this is not correct: new BDB versions change the meaning of some
offsets, so the struct needs to be adjusted for each version.
Since there are too many changes (today we're in version 170!), making
a big versioned union would be too complicated, so child_device_config
is now a union of 3 things: (i) a "raw" byte array that's safe to use
anywhere; (ii) an "old" structure that's the one we've been using and
should be safe to keep in the SDVO and TV code; and (iii) a "common"
structure that should contain only fields that are common for all the
known VBT versions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Done while reviewing all our allocations for fubar. Also a few errant
cases of lacking () for the sizeof operator - just a bit of OCD.
I've left out all the conversions that also should use kcalloc from
this patch (it's only 2).
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We haven't read the downstream port caps for DPCD 1.0, so don't use
them.
v2: use defines for DPCD 1.0 downstream port types
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm-intel-next-2013-09-21:
- clock state handling rework from Ville
- l3 parity handling fixes for hsw from Ben
- some more watermark improvements from Ville
- ban badly behaved context from Mika
- a few vlv improvements from Jesse
- VGA power domain handling from Ville
drm-intel-next-2013-09-06:
- Basic mipi dsi support from Jani. Not yet converted over to drm_bridge
since that was too fresh, but the porting is in progress already.
- More vma patches from Ben, this time the code to convert the execbuffer
code. Now that the shrinker recursion bug is tracked down we can move
ahead here again. Yay!
- Optimize hw context switching to not generate needless interrupts (Chris
Wilson). Also some shuffling for the oustanding request allocation.
- Opregion support for SWSCI, although not yet fully wired up (we need a
bit of runtime D3 support for that apparently, due to Windows design
deficiencies), from Jani Nikula.
- A few smaller changes all over.
[airlied: merge conflict fix in i9xx_set_pipeconf]
* tag 'drm-intel-next-2013-09-21-merged' of git://people.freedesktop.org/~danvet/drm-intel: (119 commits)
drm/i915: assume all GM45 Acer laptops use inverted backlight PWM
drm/i915: cleanup a min_t() cast
drm/i915: Pull intel_init_power_well() out of intel_modeset_init_hw()
drm/i915: Add POWER_DOMAIN_VGA
drm/i915: Refactor power well refcount inc/dec operations
drm/i915: Add intel_display_power_{get, put} to request power for specific domains
drm/i915: Change i915_request power well handling
drm/i915: POSTING_READ IPS_CTL before waiting for the vblank
drm/i915: don't disable ERR_INT on the IRQ handler
drm/i915/vlv: disable rc6p and rc6pp residency reporting on BYT
drm/i915/vlv: honor i915_enable_rc6 boot param on VLV
drm/i915: s/HAS_L3_GPU_CACHE/HAS_L3_DPF
drm/i915: Do remaps for all contexts
drm/i915: Keep a list of all contexts
drm/i915: Make l3 remapping use the ring
drm/i915: Add second slice l3 remapping
drm/i915: Fix HSW parity test
drm/i915: dump crtc timings from the pipe config
drm/i915: register backlight device also when backlight class is a module
drm/i915: write D_COMP using the mailbox
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
There is no clear cut rules or specs for the retry interval, as there
are many factors that affect overall response time. Increase the
interval, and even more so on branch devices which may have limited i2c
bit rates.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=60263
Tested-by: Nicolas Suzor <nic@suzor.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So far we control everything and nothing exceeds the current limits,
but (i) we never think about these limits when reviewing patches, (ii)
not all the callers check the return values and (iii) if we ever hit
any of these messages, we'll have to fix the code that added the bad
message.
The current limit for these messages is 20 since we only have 5 data
registers on all the current gens.
The checks inside intel_dp_aux_native_{write,read} are to prevent
buffer overflows. The check inside intel_dp_aux_ch is to prevent
writing past our 5 data registers.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move intel_crtc_active() to intel_display.c and make it available
elsewhere as well.
intel_edp_psr_match_conditions() already has one open coded copy,
so replace that one with a call to intel_crtc_active().
v2: Copy paste a big comment from danvet's mail explaining
when we can ditch the extra checks
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_edp_psr_match_conditions() currently looks at crtc->mode
when it really needs to look at adjusted_mode. Fix it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that adjusted_mode.clock no longer contains the pixel_multiplier, we
can kill the get_clock() callback and instead do the clock readout
in get_pipe_config().
Also i9xx_crtc_clock_get() can now extract the frequency of the PCH
DPLL, so use it to populate port_clock accurately for PCH encoders.
For DP in port A the encoder is still responsible for filling in
port_clock. The FDI adjusted_mode.clock extraction is kept in place
for some extra sanity checking, but we no longer need to pretend it's
also the port_clock.
In the encoder get_config() functions fill out adjusted_mode.clock
based on port_clock and other details such as the DP M/N values,
HDMI 12bpc and SDVO pixel_multiplier. For PCH encoders we will then
do an extra sanity check to make sure the dotclock we derived from
the FDI configuratiuon matches the one we derive from port_clock.
DVO doesn't exist on PCH platforms, so it doesn't need to anything
but assign adjusted_mode.clock=port_clock. And DDI is HSW only, so
none of the changes apply there.
v2: Use hdmi_reg color format to detect 12bpc HDMI case
v3: Set adjusted_mode.clock for LVDS too
v4: Rename ironlake_crtc_clock_get to ironlake_pch_clock_get,
eliminate the useless link_freq variable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add functions to read out the CPU and PCH transcoder M/N values,
and use them to fill out the pipe config dp_m_n information. And
while at it populate has_dp_encoder too.
Also refactor ironlake_get_fdi_m_n_config() to simply call the new
intel_cpu_transcoder_get_m_n() function.
v2: Remember the DDI
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV has per-pipe PP registers. Set up power sequencing on mode set. The
connector init time setup is problematic, since we don't have a pipe at
that time. Cook up something.
v2:
- use vlv_power_sequencer_pipe() also in _pp_{ctrl,stat}_reg()
- use PANEL_PORT_SELECT_DPC_VLV (Ville)
v3: make checkpatch happier
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Make checkpatch a bit more happier still ...]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove duplicates, add VLV specific macros for port B and C.
v2: also add PANEL_PORT_SELECT_DPC_VLV for clarity (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow-up to
commit 5004945f1d
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue Jul 30 12:20:32 2013 +0300
drm/i915: move encoder->enable callback later in VLV crtc enable
v2: Rebase on the renamed enable hooks, adding clarity (Ville)
Reference: http://mid.gmane.org/CAKMK7uFs9EMvMW8BnS24e5UNm1D7JrfVg3SD5SDFtVEamGfOOg@mail.gmail.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In line with the rest of the code base. No functional changes.
v2: also s/intel_pre_enable_dp/g4x_pre_enable_dp/ for consistency (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The patch doesn't contain functional change, but is to prepare for
future platform which has different DPIO phy. The additional pipe
parameter will use to select which phy to target for.
v2: Update the commit message and add static for the new function.
(Jani/Ville)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For DP pll settings, there is only two golden configs. Instead of
running through the algorithm to determine it, hardcode the value and get it
determine in intel_dp_set_clock.
v2: Rework on the intel_limit compiler warning. (Jani)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[danvet: Fix up checkpatch issues.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
