The bus interface provided a wrapper function to pass a single
packet to the common driver part filling a skb queue with one
packet. For clarity the caller now sets up the skb queue and
call the rx bus interface function.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several source files (but not all) define the pr_fmt() macro in exactly
the same way. Instead this commit defines it in a header file so driver
logging is consistent.
Cc: Joe Perches <joe@perches.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upon unloading the brcmfmac module the USB firmware should be reset
as the device remains powered. The reset assures a known device
state when a new brcmfmac driver load is being done.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set bitrate_mask is not desired anymore. The firmware will
determine the correct rates to be used.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When USB device gets removed rx complete comes with 0-length
packets. Do not refill those packets. In some rare cases it can
cause infinite loop.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dead code after AMPDU restructure.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interface address of the wireless device is determined by
the permanent address stored in the device. This patch allows
it to be overridden from user-space.
Reported-by: Maximilian Engelhardt <maxi@daemonizer.de>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All callbacks that access driver functions should do that under
perimeter lock protection. The add_interface() callback was lacking
this lock.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On hardware reintialization reference count of
already existing timers would be increased again.
This leads to problems on module unloading.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both the rtt2x00usb_eeprom_read and the ioremap
functions are allowed to fail, however their
return values are not checked in the read_eeprom
functions in the rt2800{pci,usb} drivers.
The patch adds the missing checks, and converts
all read_eeprom functions to return an int value,
so the error values can be propagated up to the
'rt2800_validate_eeprom' function.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/brcm80211/brcmsmac/main.c: In function ‘brcms_b_recv’:
drivers/net/wireless/brcm80211/brcmsmac/main.c:7636: warning: ‘morepending’ may be used uninitialized in this function
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Power save support was removed from iwlegacy due to possible firmware
crashes problems it cause. I use to plan first inspect code to find
reason of problems, fix them and then allow to enable PS. But
realistically - code inspection will not happen, so let's do it, and
wait for eventual bug reports.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dump implementation of flush, which just wait until all TX queues
become empty.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some 3-column initval arrays have wrong comments. The
column of these arrays is indexed by the 'freqIndex'
variable in 'ar5008_hw_process_ini' which only depends
on the actual band.
The 'initvals' tool from 'qca-swiss-army-knife' prints
the correct comment lines for these arrays, since commit
'atheros-initvals: fix comments for non-fastclock 3-column tables'
however the comments were not refreshed in ath9k.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves parts of carl9170_update_beacon
into separate subroutines, so the parts become
more manageable.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit: "mac80211: introduce IEEE80211_NUM_TIDS and use it"
introduced a generic NUM_TID definitions for all everyone.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While the driver supports HW offload in a single
P2P client configuration, it doesn't support HW
offload in the concurrent P2P GO+CLIENT
configuration.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, op_start would set disable_offload always
to false, even if it was set to true by the fw parser.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise carl9170 triggers a warning in cfg80211, from net/wireless/core.c
/* Combinations with just one interface aren't real */
if (WARN_ON(c->max_interfaces < 2))
Note: The number of supported interfaces is set by
the carl9170 firmware. The default number of
supported interfaces for all current firmwares is 2.
Therefore this warning can only be observed with
custom firmwares.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Janusz Dziedzic reported that after a change in wpa_supplicant
["nl80211: Automatically use concurrent P2P if possible"],
carl9170 was no longer able to host a P2P network.
This patch tackles the problem by allowing GO interfaces to be
registered, long after the P2P_CLIENT interface is brought up.
Reported-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on a quick test [ath9k and carl9170],
TDLS seemed to be working fine. And while
we are at it, let's move the wiphy feature
flag set from carl9170_alloc into a single
place in carl9170_fw.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800_init_rfcsr() is too big, split RF initialization into per chip
functions. Code will change, but we should setup the same values onto
RF registers and in the same order as before.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows to let sparse check that the NIC access is
always released.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix typo in the macro name and the wrong value.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Synchronizing the IRQ is pointless when we will
then enable the RF-Kill interrupt again, but is
needed before we free it and the data needed to
handle IRQs; move it to the free function.
Simiarly, cancelling the replenish work struct
can move to the function that frees the RX data
structures.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to request the IRQ every time the
device is started, we can request it just once.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_trans_grab_nic_access returns a boolean. So ret should
explicitely set to an error code and not rely on the value
returned by iwl_trans_grab_nic_access.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Different transports implement the access to the SRAM in
different ways. Virtualize it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since different transports have different ways to wake the
up the NIC, we need to virtualize it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use __packed instead of __attribute__((packed)).
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, the fw should run even if the NIC is in
RFKILL. Make the API more flexible to allow that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No need to verify that the fw has been written correctly.
In case it hasn't, we won't get ALIVE notification.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we take a pointer to the tid_data, then use it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When TX aggregation is stopped, there are a few
different cases:
- connection with the peer was dropped
- session stop was requested locally
- session stop was requested by the peer
- connection was dropped while a session is stopping
The behaviour in these cases should be different, if
the connection is dropped then the driver should drop
all frames, otherwise the frames may continue to be
transmitted, aggregated in the case of a locally
requested session stop or unaggregated in the case of
the peer requesting session stop.
Split these different cases so that the driver can
act accordingly; however, treat local and remote stop
the same way and ask the driver to not send frames as
aggregated packets any more.
In the case of connection drop, the stop callback the
driver is otherwise supposed to call is no longer
required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of returning an error and filling a pointer
return the pointer and an ERR_PTR value in error cases.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel bandwidth handling isn't really quite right,
it assumes that a 40 MHz channel is really two 20 MHz
channels, which isn't strictly true. This is the way the
regulatory database handling is defined right now though
so remove the logic to handle other channel widths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Paged RX, i.e. SKBs with (some of) the data in pages instead
of the SKB header data (skb->data) can behave differently in
the stack and cause other bugs. To make debugging easier add
an option to hwsim to test with such SKBs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- cxgb4 changes to fix lookup engine hash collisions
- mlx4 changes to make flow steering usable
- fix to IPoIB to avoid pinning dst reference for too long
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lDXt
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull more infiniband changes from Roland Dreier:
"Second batch of InfiniBand/RDMA changes for 3.8:
- cxgb4 changes to fix lookup engine hash collisions
- mlx4 changes to make flow steering usable
- fix to IPoIB to avoid pinning dst reference for too long"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cxgb4: Fix bug for active and passive LE hash collision path
RDMA/cxgb4: Fix LE hash collision bug for passive open connection
RDMA/cxgb4: Fix LE hash collision bug for active open connection
mlx4_core: Allow choosing flow steering mode
mlx4_core: Adjustments to Flow Steering activation logic for SR-IOV
mlx4_core: Fix error flow in the flow steering wrapper
mlx4_core: Add QPN enforcement for flow steering rules set by VFs
cxgb4: Add LE hash collision bug fix path in LLD driver
cxgb4: Add T4 filter support
IPoIB: Call skb_dst_drop() once skb is enqueued for sending
Latinoware 2012.
There's a slightly non-trivial merge in virtio-net, as we cleaned up the
virtio add_buf interface while DaveM accepted the mq virtio-net patches.
You can see my solution in my pending-rebases branch, if that helps, but I
know you love merging:
https://git.kernel.org/?p=linux/kernel/git/rusty/linux.git;a=commit;h=12e4e64fa66a4c812e4855de32abdb4d819526fe
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=myDR
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio update from Rusty Russell:
"Some nice cleanups, and even a patch my wife did as a "live" demo for
Latinoware 2012.
There's a slightly non-trivial merge in virtio-net, as we cleaned up
the virtio add_buf interface while DaveM accepted the mq virtio-net
patches."
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (27 commits)
virtio_console: Add support for remoteproc serial
virtio_console: Merge struct buffer_token into struct port_buffer
virtio: add drv_to_virtio to make code clearly
virtio: use dev_to_virtio wrapper in virtio
virtio-mmio: Fix irq parsing in command line parameter
virtio_console: Free buffers from out-queue upon close
virtio: Convert dev_printk(KERN_<LEVEL> to dev_<level>(
virtio_console: Use kmalloc instead of kzalloc
virtio_console: Free buffer if splice fails
virtio: tools: make it clear that virtqueue_add_buf() no longer returns > 0
virtio: scsi: make it clear that virtqueue_add_buf() no longer returns > 0
virtio: rpmsg: make it clear that virtqueue_add_buf() no longer returns > 0
virtio: net: make it clear that virtqueue_add_buf() no longer returns > 0
virtio: console: make it clear that virtqueue_add_buf() no longer returns > 0
virtio: make virtqueue_add_buf() returning 0 on success, not capacity.
virtio: console: don't rely on virtqueue_add_buf() returning capacity.
virtio_net: don't rely on virtqueue_add_buf() returning capacity.
virtio-net: remove unused skb_vnet_hdr->num_sg field
virtio-net: correct capacity math on ring full
virtio: move queue_index and num_free fields into core struct virtqueue.
...
Retries active opens for INUSE errors.
Logs any active ofld_connect_wr error replies.
Sends ofld_connect_wr on same ctrlq. It needs to go on the same control txq as
regular CPL active/passive messages.
Retries on active open replies with EADDRINUSE.
Uses active open fw wr only if active filter region is set.
Adds stat for ofld_connect_wr failures.
This patch also adds debugfs file to show endpoints.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
It establishes passive open connection through firmware work request. Passive
open connection will go through this path as now instead of listening server we
create a server filter which will redirect the incoming SYN packet to the
offload queue. After this driver tries to establish the connection using
firmware work request.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
It enables establishing active open connection using fw_ofld_connection work
request when cpl_act_open_rpl says TCAM full error which may be because
of LE hash collision. Current support is only for IPv4 active open connections.
Sets ntuple bits in active open requests. For T4 firmware greater than 1.4.10.0
ntuple bits are required to be set.
Adds nocong and enable_ecn module parameter options.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
[ Move all FW return values to t4fw_api.h. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull networking fixes from David Miller:
1) Really fix tuntap SKB use after free bug, from Eric Dumazet.
2) Adjust SKB data pointer to point past the transport header before
calling icmpv6_notify() so that the headers are in the state which
that function expects. From Duan Jiong.
3) Fix ambiguities in the new tuntap multi-queue APIs. From Jason
Wang.
4) mISDN needs to use del_timer_sync(), from Konstantin Khlebnikov.
5) Don't destroy mutex after freeing up device private in mac802154,
fix also from Konstantin Khlebnikov.
6) Fix INET request socket leak in TCP and DCCP, from Christoph Paasch.
7) SCTP HMAC kconfig rework, from Neil Horman.
8) Fix SCTP jprobes function signature, otherwise things explode, from
Daniel Borkmann.
9) Fix typo in ipv6-offload Makefile variable reference, from Simon
Arlott.
10) Don't fail USBNET open just because remote wakeup isn't supported,
from Oliver Neukum.
11) be2net driver bug fixes from Sathya Perla.
12) SOLOS PCI ATM driver bug fixes from Nathan Williams and David
Woodhouse.
13) Fix MTU changing regression in 8139cp driver, from John Greene.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
solos-pci: ensure all TX packets are aligned to 4 bytes
solos-pci: add firmware upgrade support for new models
solos-pci: remove superfluous debug output
solos-pci: add GPIO support for newer versions on Geos board
8139cp: Prevent dev_close/cp_interrupt race on MTU change
net: qmi_wwan: add ZTE MF880
drivers/net: Use of_match_ptr() macro in smsc911x.c
drivers/net: Use of_match_ptr() macro in smc91x.c
ipv6: addrconf.c: remove unnecessary "if"
bridge: Correctly encode addresses when dumping mdb entries
bridge: Do not unregister all PF_BRIDGE rtnl operations
use generic usbnet_manage_power()
usbnet: generic manage_power()
usbnet: handle PM failure gracefully
ksz884x: fix receive polling race condition
qlcnic: update driver version
qlcnic: fix unused variable warnings
net: fec: forbid FEC_PTP on SoCs that do not support
be2net: fix wrong frag_idx reported by RX CQ
be2net: fix be_close() to ensure all events are ack'ed
...
