Commit Graph

7405 Commits

Author SHA1 Message Date
Vivek Natarajan
3a37495268 ath9k: Avoid corrupt frames being forwarded to mac80211.
If bit 29 is set, MAC H/W can attempt to decrypt the received aggregate
with WEP or TKIP, eventhough the received frame may be a CRC failed
corrupted frame. If this bit is set, H/W obeys key type in keycache.
If it is not set and if the key type in keycache is neither open nor
AES, H/W forces key type to be open.  But bit 29 should be set to 1
for AsyncFIFO feature to encrypt/decrypt the aggregate with WEP or TKIP.

Cc: stable@kernel.org
Reported-by: Johan Hovold <johan.hovold@lundinova.se>
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: Ranga Rao Ravuri <ranga.ravuri@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:22 -04:00
Vivek Natarajan
8a8572a821 ath9k_htc: Handle CONF_IDLE during unassociated state to save power.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:21 -04:00
Luis R. Rodriguez
5bea40069e ath9k_hw: Fix TX interrupt mitigation settings
TX interrupt mitigation reduces the number of interrupts
by addressing several interrupt actions (AR_IMR_TXOK,
AR_IMR_TXDESC) all in one interrupt so when enabling
it discard setting the other interrupts.

Without this TX interrupt mitigation would actually
increase the number of interrupts two-fold. We still
leave TX interrupt mitigation disabled as it is still
being tested.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:20 -04:00
Felix Fietkau
5d5d44d914 ath9k_hw: fix noisefloor timeout handling on AR9003
When the noisefloor calibration times out, do not load -50 into
the registers, since this might cause rx issues. Instead, leave
enough time for the noise floor calibration to complete until
the next check.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:20 -04:00
Felix Fietkau
0cf31079e9 ath9k_hw: Fix endian bug in an AR9003 EEPROM field
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:20 -04:00
Felix Fietkau
d10baf99ff ath9k_hw: Fix typos in tx rate power level parsing for AR9003
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:18 -04:00
Felix Fietkau
597a94b340 ath9k_hw: use the configured power limit for AR9003
Since the new AR9003 EEPROM code does tune the card for the configured
tx power level, we need to fill in the correct power limits in the TPC
part of the DMA descriptor.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:18 -04:00
Felix Fietkau
7f9f360069 ath9k: wake queue after processing edma rx frames
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:18 -04:00
Felix Fietkau
6b42e8d03b ath9k_hw: fix fast clock handling for 5GHz channels
Combine multiple checks that were supposed to check for the same
conditions, but didn't. Always enable fast PLL clock on AR9280 2.0

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:18 -04:00
Felix Fietkau
5b75d0fca5 ath9k_hw: update EEPROM data structure for AR9280
Adds read access for the 5 GHz fast clock flag

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:17 -04:00
Vasanthakumar Thiagarajan
e55537240f ath9k_hw: Fix usec to hw clock conversion in 5Ghz for ar9003
Fast clock operation (44Mhz) is enabled for 5Ghz in ar9003, so
take care of the conversion from usec to hw clock.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:17 -04:00
Luis R. Rodriguez
b360a88483 ath9k_hw: disable TX IQ calibration for AR9003
Disable TX IQ calibration, it was prematurely enabled in
previous versions.

Cc: Paul Shaw <Paul.Shaw@Atheros.com>
Cc: Thomas Hammel <Thomas.Hammel@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:17 -04:00
Felix Fietkau
8393722765 ath9k_hw: fix typo in the AR9003 EEPROM data structure definition
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:17 -04:00
Felix Fietkau
14bc110463 ath9k_hw: fix pll clock setting for 5ghz on AR9003
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:16 -04:00
Felix Fietkau
2fcb913173 ath9k_hw: update initvals for AR9003
This synchs up the initvals to the values used on the
Atheros HAL for AR9003. This specific change adds support
for a new high power module.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:16 -04:00
Sujith
4f824719a2 ath9k_htc: Simplify RX IRQ handler
A bunch of validation and processing in the RX IRQ handler
can be moved to the RX tasklet. The IRQ handler is
already heavy, with the memory allocation for handling
stream mode. Also, a memcpy of 40 bytes for every packet
can be avoided in the handler.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:15 -04:00
Sujith
d439260e04 ath9k_htc: Validate TX Endpoint ID
Check for the endpoint IDs when processing
TX completions and drop the unsupported EPIDs.

We can add other endpoints (UAPSD,..) when support
is added.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:15 -04:00
Sujith
5bf1e17a4a ath9k_htc: Remove unnecessary powersave restore
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-27 16:09:15 -04:00
Steve deRosier
e9bd5bcde7 libertastf: add configurable debug messages
Add the same type of configurable debug messages to libertas_tf as
already exist in the libertas driver.  This has facilitated creation
of a interface specification and will facilitate future development
of this driver.

Signed-off-by: Steve deRosier <steve@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:26 -04:00
Helmut Schaa
9a8b424ea8 rt2x00: rt2800lib: Remove redundant check for RT2872
Remove redundant check for RT2872.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:25 -04:00
Helmut Schaa
23812383c6 rt2x00: rt2800lib: Fix rx path on SoC devices
Restore the rfcsr initialization for RT305x SoC devices which was removed
by "rt2x00: Finish rt3070 support in rt2800 register initialization.".

This fixes the rx path on SoC devices.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:24 -04:00
Helmut Schaa
0bdab171ec rt2x00: fix typo in rt2800.h
Fix a typo in a comment in rt2800.h. Instead of replacing the wrong
hexvalue (0x171c) with the correct one (0x1718) just use the appropriate
readable define.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:24 -04:00
Helmut Schaa
5a67396426 rt2x00: rt2800: use tx_power2 in rt2800_config_channel_rf3xxx
Get closer to what the ralink driver does by setting the rf register 13
to tx_power2 during channel switch.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:23 -04:00
Helmut Schaa
2caaa5d36e rt2x00: rt2800lib: disable HT40 for now as it causes reception problems
Disable HT40 support for now as it causes rx problems with HT40 capable
11n APs (when mac80211 enables HT40, rx is completely disfunctional).

Once the rt2800 HT code is capable of using HT40 we should enable the
flag again.

I only tested this patch with a rt305x SoC device, nevertheless the
patch disables HT40 also on PCI and USB rt2800 devices.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:22 -04:00
Sujith
d8f996f6ff ath9k_htc: Really fix device hotunplug
All commands to the target are disabled when the device
is unplugged, but a normal module unload has to be
differentiated from this case, as we could still receive
data in the RX endpoint. Fix this by checking if the
device is attached or not.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:22 -04:00
Sujith
0d36d71da2 ath9k_htc: Fix WMI command race
My patch "ath9k_htc: Handle WMI timeouts properly" introduced
a race condition in WMI command processing. The last issued command
should be stored _before_ issuing a WMI command. Not doing this
would result in the WMI event IRQ dropping correct command responses
as invalid.

Fix this race by storing the command id correctly.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:21 -04:00
Sujith
ba44370175 ath9k_htc: Increase WMI timeout value
Completion of WMI commands take a longer time
on some platforms. Increase the timeout value
to handle this.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:20 -04:00
Sujith
5ab0af3270 ath9k_htc: Process command data properly
When handling the REGIN callback, processing
the incoming data first should be the preferred
mode of operation. Allocation of a new SKB may fail,
in which case, the URB will not be resubmitted.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:20 -04:00
Sujith
62e4716aff ath9k_htc: Use USB reboot
So, apparently there is a USB reboot command
that the target accepts. Using this instead of
usb_reset_device() fixes the issue of "descriptor read error"
that pops up on repeated load/unload.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:19 -04:00
Sujith
f66890724f ath9k_htc: Pass correct private pointer
In the TX callback, the HTC layer has to pass the
priv pointer that was registered during service initialization.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:18 -04:00
Sujith
51f139d567 ath9k_hw: Remove pointless ANI deinit
There is no reason to disable the PHY Error / MIB counters
when the module is being unloaded.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:18 -04:00
Sujith
7073daa63b ath9k_htc: Cancel running timers before disabling HW
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:17 -04:00
Sujith
d5e347bf0f ath9k_htc: Use multiple register writes
This patch fixes a code segment in configpciepowersave()
to make use of multiple register writes.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:17 -04:00
Sujith
a3be14b76d ath9k_htc: Handle device unplug properly
When the USB device has been unplugged, there is
no point in trying to send commands to the target.
Fix this by denying all WMI commands in such a case.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:16 -04:00
Sujith
c11d8f89d3 ath9k_htc: Simplify TX URB management
This patch simplifies URB management for transmission,
by removing the 'FLUSH' variable (which is not needed,
since we can determine if the URB has been killed by
looking at the URB status), and also handling the STOP
case properly.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:16 -04:00
Hans de Goede
d4cde88c1c p54pci: fix regression from prevent stuck rx-ring on slow system
This patch fixes a recently introduced use-after-free regression
from "p54pci: prevent stuck rx-ring on slow system".

Hans de Goede reported a use-after-free regression:
>BUG: unable to handle kernel paging request at 6b6b6b6b
>IP: [<e122284a>] p54p_check_tx_ring+0x84/0xb1 [p54pci]
>*pde = 00000000
>Oops: 0000 [#1] SMP
>EIP: 0060:[<e122284a>] EFLAGS: 00010286 CPU: 0
>EIP is at p54p_check_tx_ring+0x84/0xb1 [p54pci]
>EAX: 6b6b6b6b EBX: df10b170 ECX: 00000003 EDX: 00000001
>ESI: dc471500 EDI: d8acaeb0 EBP: c098be9c ESP: c098be84
> DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
>Process swapper (pid: 0, ti=c098a000 task=c09ccfe0 task.ti=c098a000)
>Call Trace:
> [<e1222b02>] ? p54p_tasklet+0xaa/0xb5 [p54pci]
> [<c0440568>] ? tasklet_action+0x78/0xcb
> [<c0440ed3>] ? __do_softirq+0xbc/0x173

Quote from comment #17:
"The problem is the innocent looking moving of the tx processing to
 after the rx processing in the tasklet. Quoting from the changelog:
  This patch does it the same way, except that it also prioritize
  rx data processing, simply because tx routines *can* wait.

 This is causing an issue with us referencing already freed memory,
 because some skb's we transmit, we immediately receive back, such
 as those for reading the eeprom (*) and getting stats.

 What can happen because of the moving of the tx processing to after
 the rx processing is that when the tasklet first runs after doing a
 special skb tx (such as eeprom) we've already received the answer
 to it.

 Then the rx processing ends up calling p54_find_and_unlink_skb to
 find the matching tx skb for the just received special rx skb and
 frees the tx skb.

 Then after the processing of the rx skb answer, and thus freeing
 the tx skb, we go process the completed tx ring entires, and then
 dereference the free-ed skb, to see if it should free free-ed by
 p54p_check_tx_ring()."

Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=583623
Bug-Identified-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-26 14:21:15 -04:00
Luis R. Rodriguez
81b208a6b6 ath9k_hw: make all AR9002 initvals use u32
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-21 14:15:18 -04:00
Luis R. Rodriguez
020ab48d1e ath9k_hw: make two initvals consto for the AR9001 family
This makes ar5416Addac_9160 and ar5416Addac_9160 const
I guess we skipped them long ago.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-21 14:15:18 -04:00
Felix Fietkau
58b5190e74 ath9k: set the STBC flag in rate control if the peer supports it
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-20 11:52:39 -04:00
Felix Fietkau
074a8c0db2 ath9k: add support for Tx and Rx STBC
Supported only for single stream rates by the hardware

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-20 11:52:36 -04:00
Felix Fietkau
3bb065a742 ath9k: initialize the number of tx/rx streams correctly
AR9300 based hardware can 3x3 MCS rates, this should be set in the
HT capabilities.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-20 11:50:54 -04:00
Felix Fietkau
c666387682 ath9k: reduce the bits_per_symbol table size, support more streams
Instead of increasing bits_per_symbol for supporting more streams, keep
it single-stream only and multiply the values by the numer of streams.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-20 11:50:53 -04:00
Felix Fietkau
0e668cde0d ath9k: update the ath_max_4ms_framelen table
Include MCS0-31 and also add SGI for HT20. This makes it
possible to support more different rate combinations with
newer hardware.

Based on a patch by Selvam. T.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-20 11:50:53 -04:00
Felix Fietkau
7817e4ceb6 ath9k: update the MCS mask for MCS16 and above
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-20 11:50:53 -04:00
Felix Fietkau
0a8cea844d ath9k: clean up tx buffer handling
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-20 11:50:53 -04:00
Felix Fietkau
c9c99e5e44 ath9k: check for specific rx stuck conditions and recover from them
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-20 11:50:52 -04:00
Holger Schurig
55ee82b500 ath5k: basic support for survey
This adds the first element of survey data, the noise floor figure.

Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-20 11:50:52 -04:00
Holger Schurig
1289723ef2 mac80211: sample survey implementation for mac80211 & hwsim
This adds the survey function to both mac80211 itself and to mac80211_hwsim.
For the latter driver, we simply invent some noise level.A real driver which
cannot determine the real channel noise MUST NOT report any noise, especially
not a magically conjured one :-)

Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-20 11:50:52 -04:00
Daniel Yingqiang Ma
03ceedea97 ath9k: Group Key fix for VAPs
When I set up multiple VAPs with ath9k, I encountered an issue that
the traffic may be lost after a while.

The detailed phenomenon is
1. After a while the clients connected to one of these VAPs will get
into a state that no broadcast/multicast packets can be transfered
successfully while the unicast packets can be transfered normally.
2. Minutes latter the unitcast packets transfer will fail as well,
because the ARP entry is expired and it can't be freshed due to the
broadcast trouble.

It's caused by the group key overwritten and someone discussed this
issue in ath9k-devel maillist before, but haven't work out a fix yet.

I referred the method in madwifi, and made a patch for ath9k.
The method is to set the high bit of the sender(AP)'s address, and
associated that mac and the group key. It requires the hardware
supports multicast frame key search. It seems true for AR9160.

Not sure whether it's the correct way to fix this issue. But it seems
to work in my test. The patch is attached, feel free to revise it.

Signed-off-by: Daniel Yingqiang ma <yma.cool@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-20 11:50:51 -04:00
Xose Vazquez Perez
e895833019 wireless: rt2x00: rt2800usb: identify Allwin devices
Applied common sense, no info from the manufacturer:

(0x8516, 0x2070) is RT2070
(0x8516, 0x2770) is RT2770
(0x8516, 0x2870) is RT2870
[...]

Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-04-19 16:45:20 -04:00