Devesh Sharma <Devesh.Sharma@Emulex.Com> reports that after a
disconnect, his HCA is failing to create a fresh QP, leaving
ia_ri->ri_id->qp set to NULL. But xprtrdma still allows RPCs to
wake up and post LOCAL_INV as they exit, causing an oops.
rpcrdma_ep_connect() is allowing the wake-up by leaking the QP
creation error code (-EPERM in this case) to the RPC client's
generic layer. xprt_connect_status() does not recognize -EPERM, so
it kills pending RPC tasks immediately rather than retrying the
connect.
Re-arrange the QP creation logic so that when it fails on reconnect,
it leaves ->qp with the old QP rather than NULL. If pending RPC
tasks wake and exit, LOCAL_INV work requests will flush rather than
oops.
On initial connect, leaving ->qp == NULL is OK, since there are no
pending RPCs that might use ->qp. But be sure not to try to destroy
a NULL QP when rpcrdma_ep_connect() is retried.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
While marshaling an RPC/RDMA request, the inline_{rsize,wsize}
settings determine whether an inline request is used, or whether
read or write chunks lists are built. The current default value of
these settings is 1024. Any RPC request smaller than 1024 bytes is
sent to the NFS server completely inline.
rpcrdma_buffer_create() allocates and pre-registers a set of RPC
buffers for each transport instance, also based on the inline rsize
and wsize settings.
RPC/RDMA requests and replies are built in these buffers. However,
if an RPC/RDMA request is expected to be larger than 1024, a buffer
has to be allocated and registered for that RPC, and deregistered
and released when the RPC is complete. This is known has a
"hardway allocation."
Since the introduction of NFSv4, the size of RPC requests has become
larger, and hardway allocations are thus more frequent. Hardway
allocations are significant overhead, and they waste the existing
RPC buffers pre-allocated by rpcrdma_buffer_create().
We'd like fewer hardway allocations.
Increasing the size of the pre-registered buffers is the most direct
way to do this. However, a blanket increase of the inline thresholds
has interoperability consequences.
On my 64-bit system, rpcrdma_buffer_create() requests roughly 7000
bytes for each RPC request buffer, using kmalloc(). Due to internal
fragmentation, this wastes nearly 1200 bytes because kmalloc()
already returns an 8192-byte piece of memory for a 7000-byte
allocation request, though the extra space remains unused.
So let's round up the size of the pre-allocated buffers, and make
use of the unused space in the kmalloc'd memory.
This change reduces the amount of hardway allocated memory for an
NFSv4 general connectathon run from 1322092 to 9472 bytes (99%).
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Sagi Grimberg <sagig@dev.mellanox.co.il> points out that a steady
stream of CQ events could starve other work because of the boundless
loop pooling in rpcrdma_{send,recv}_poll().
Instead of a (potentially infinite) while loop, return after
collecting a budgeted number of completions.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Acked-by: Sagi Grimberg <sagig@dev.mellanox.co.il>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Change the completion handlers to grab up to 16 items per
ib_poll_cq() call. No extra ib_poll_cq() is needed if fewer than 16
items are returned.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Skip the ib_poll_cq() after re-arming, if the provider knows there
are no additional items waiting. (Have a look at commit ed23a727 for
more details).
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The current CQ handler uses the ib_wc.opcode field to distinguish
between event types. However, the contents of that field are not
reliable if the completion status is not IB_WC_SUCCESS.
When an error completion occurs on a send event, the CQ handler
schedules a tasklet with something that is not a struct rpcrdma_rep.
This is never correct behavior, and sometimes it results in a panic.
To resolve this issue, split the completion queue into a send CQ and
a receive CQ. The send CQ handler now handles only struct rpcrdma_mw
wr_id's, and the receive CQ handler now handles only struct
rpcrdma_rep wr_id's.
Fix suggested by Shirley Ma <shirley.ma@oracle.com>
Reported-by: Rafael Reiter <rafael.reiter@ims.co.at>
Fixes: 5c635e09ce
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=73211
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Klemens Senn <klemens.senn@ims.co.at>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: rpcrdma_ep_destroy() returns a value that is used
only to print a debugging message. rpcrdma_ep_destroy() already
prints debugging messages in all error cases.
Make rpcrdma_ep_destroy() return void instead.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: All remaining callers of rpcrdma_deregister_external()
pass NULL as the last argument, so remove that argument.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If the selected memory registration mode is not supported by the
underlying provider/HCA, the NFS mount command reports that there was
an invalid mount option, and fails. This is misleading.
Reporting a problem allocating memory is a lot closer to the truth.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
An audit of in-kernel RDMA providers that do not support the FRMR
memory registration shows that several of them support MTHCAFMR.
Prefer MTHCAFMR when FRMR is not supported.
If MTHCAFMR is not supported, only then choose ALLPHYSICAL.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
All kernel RDMA providers except amso1100 support either MTHCAFMR
or FRMR, both of which are faster than REGISTER. amso1100 can
continue to use ALLPHYSICAL.
The only other ULP consumer in the kernel that uses the reg_phys_mr
verb is Lustre.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The MEMWINDOWS and MEMWINDOWS_ASYNC memory registration modes were
intended as stop-gap modes before the introduction of FRMR. They
are now considered obsolete.
MEMWINDOWS_ASYNC is also considered unsafe because it can leave
client memory registered and exposed for an indeterminant time after
each I/O.
At this point, the MEMWINDOWS modes add needless complexity, so
remove them.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: This memory registration mode is slow and was never
meant for use in production environments. Remove it to reduce
implementation complexity.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
An IB provider can invoke rpcrdma_conn_func() in an IRQ context,
thus rpcrdma_conn_func() cannot be allowed to directly invoke
generic RPC functions like xprt_wake_pending_tasks().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Two memory region leaks were found during testing:
1. rpcrdma_buffer_create: While allocating RPCRDMA_FRMR's
ib_alloc_fast_reg_mr is called and then ib_alloc_fast_reg_page_list is
called. If ib_alloc_fast_reg_page_list returns an error it bails out of
the routine dropping the last ib_alloc_fast_reg_mr frmr region creating a
memory leak. Added code to dereg the last frmr if
ib_alloc_fast_reg_page_list fails.
2. rpcrdma_buffer_destroy: While cleaning up, the routine will only free
the MR's on the rb_mws list if there are rb_send_bufs present. However, in
rpcrdma_buffer_create while the rb_mws list is being built if one of the MR
allocation requests fail after some MR's have been allocated on the rb_mws
list the routine never gets to create any rb_send_bufs but instead jumps to
the rpcrdma_buffer_destroy routine which will never free the MR's on rb_mws
list because the rb_send_bufs were never created. This leaks all the MR's
on the rb_mws list that were created prior to one of the MR allocations
failing.
Issue(2) was seen during testing. Our adapter had a finite number of MR's
available and we created enough connections to where we saw an MR
allocation failure on our Nth NFS connection request. After the kernel
cleaned up the resources it had allocated for the Nth connection we noticed
that FMR's had been leaked due to the coding error described above.
Issue(1) was seen during a code review while debugging issue(2).
Signed-off-by: Allen Andrews <allen.andrews@emulex.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Some rdma devices don't support a fast register page list depth of
at least RPCRDMA_MAX_DATA_SEGS. So xprtrdma needs to chunk its fast
register regions according to the minimum of the device max supported
depth or RPCRDMA_MAX_DATA_SEGS.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we jump to free_pcpu on failure in alloc_netdev_mqs()
rx and tx queues are not yet allocated, so no need to free them.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that ->newlink() fails before registering
the device, in this case we should just free it, it's
safe to call free_netdev().
Fixes: commit 0e0eee2465 (net: correct error path in rtnl_newlink())
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xfrm_user module registers its pernet init/exit after xfrm
itself so that its net exit function xfrm_user_net_exit() is
executed before xfrm_net_exit() which calls xfrm_state_fini() to
cleanup the SA's (xfrm states). This opens a window between
zeroing net->xfrm.nlsk pointer and deleting all xfrm_state
instances which may access it (via the timer). If an xfrm state
expires in this window, xfrm_exp_state_notify() will pass null
pointer as socket to nlmsg_multicast().
As the notifications are called inside rcu_read_lock() block, it
is sufficient to retrieve the nlsk socket with rcu_dereference()
and check the it for null.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
Pull request: Fixes for new ethtool RSS commands
This addresses several problems I previously identified with the new
ETHTOOL_{G,S}RSSH commands:
1. Missing validation of reserved parameters
2. Vague documentation
3. Use of unnamed magic number
4. No consolidation with existing driver operations
I don't currently have access to suitable network hardware, but have
tested these changes with a dummy driver that can support various
combinations of operations and sizes, together with (a) Debian's ethtool
3.13 (b) ethtool 3.14 with the submitted patch to use ETHTOOL_{G,S}RSSH
and minor adjustment for fixes 1 and 3.
v2: Update RSS operations in vmxnet3 too
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ETHTOOL_{G,S}RXFHINDIR and ETHTOOL_{G,S}RSSH should work for drivers
regardless of whether they expose the hash key, unless you try to
set a hash key for a driver that doesn't expose it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
(This patch was previously posted as RFC at
http://patchwork.ozlabs.org/patch/352677/)
This patch adds NDA_MASTER attribute to neighbour attributes enum for
bridge/master ifindex. And adds NDA_MASTER to bridge fdb notify msgs.
Today bridge fdb notifications dont contain bridge information.
Userspace can derive it from the port information in the fdb
notification. However this is tricky in some scenarious.
Example, bridge port delete notification comes before bridge fdb
delete notifications. And we have seen problems in userspace
when using libnl where, the bridge fdb delete notification handling code
does not understand which bridge this fdb entry is part of because
the bridge and port association has already been deleted.
And these notifications (port membership and fdb) are generated on
separate rtnl groups.
Fixing the order of notifications could possibly solve the problem
for some cases (I can submit a separate patch for that).
This patch chooses to add NDA_MASTER to bridge fdb notify msgs
because it not only solves the problem described above, but also helps
userspace avoid another lookup into link msgs to derive the master index.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__sk_prepare_filter() was reworked in commit bd4cf0ed3 (net: filter:
rework/optimize internal BPF interpreter's instruction set) so that it should
have uncharged memory once things went wrong. However that work isn't complete.
Error is handled only in __sk_migrate_filter() while memory can still leak in
the error path right after sk_chk_filter().
Fixes: bd4cf0ed33 ("net: filter: rework/optimize internal BPF interpreter's instruction set")
Signed-off-by: Leon Yu <chianglungyu@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Tested-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug is discovered by an recent F-RTO issue on tcpm list
https://www.ietf.org/mail-archive/web/tcpm/current/msg08794.html
The bug is that currently F-RTO does not use DSACK to undo cwnd in
certain cases: upon receiving an ACK after the RTO retransmission in
F-RTO, and the ACK has DSACK indicating the retransmission is spurious,
the sender only calls tcp_try_undo_loss() if some never retransmisted
data is sacked (FLAG_ORIG_DATA_SACKED).
The correct behavior is to unconditionally call tcp_try_undo_loss so
the DSACK information is used properly to undo the cwnd reduction.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make fib_triestat_seq_show consistent with other /proc/net files and
use seq_file_net.
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was possible to get a setuid root or setcap executable to write to
it's stdout or stderr (which has been set made a netlink socket) and
inadvertently reconfigure the networking stack.
To prevent this we check that both the creator of the socket and
the currentl applications has permission to reconfigure the network
stack.
Unfortunately this breaks Zebra which always uses sendto/sendmsg
and creates it's socket without any privileges.
To keep Zebra working don't bother checking if the creator of the
socket has privilege when a destination address is specified. Instead
rely exclusively on the privileges of the sender of the socket.
Note from Andy: This is exactly Eric's code except for some comment
clarifications and formatting fixes. Neither I nor, I think, anyone
else is thrilled with this approach, but I'm hesitant to wait on a
better fix since 3.15 is almost here.
Note to stable maintainers: This is a mess. An earlier series of
patches in 3.15 fix a rather serious security issue (CVE-2014-0181),
but they did so in a way that breaks Zebra. The offending series
includes:
commit aa4cf9452f
Author: Eric W. Biederman <ebiederm@xmission.com>
Date: Wed Apr 23 14:28:03 2014 -0700
net: Add variants of capable for use on netlink messages
If a given kernel version is missing that series of fixes, it's
probably worth backporting it and this patch. if that series is
present, then this fix is critical if you care about Zebra.
Cc: stable@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed we were sending wrong IPv4 ID in TCP flows when MTU discovery
is disabled.
Note how GSO/TSO packets do not have monotonically incrementing ID.
06:37:41.575531 IP (id 14227, proto: TCP (6), length: 4396)
06:37:41.575534 IP (id 14272, proto: TCP (6), length: 65212)
06:37:41.575544 IP (id 14312, proto: TCP (6), length: 57972)
06:37:41.575678 IP (id 14317, proto: TCP (6), length: 7292)
06:37:41.575683 IP (id 14361, proto: TCP (6), length: 63764)
It appears I introduced this bug in linux-3.1.
inet_getid() must return the old value of peer->ip_id_count,
not the new one.
Lets revert this part, and remove the prevention of
a null identification field in IPv6 Fragment Extension Header,
which is dubious and not even done properly.
Fixes: 87c48fa3b4 ("ipv6: make fragment identifications less predictable")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_handle_local_finish() is allowing us to insert an FDB entry with
disallowed vlan. For example, when port 1 and 2 are communicating in
vlan 10, and even if vlan 10 is disallowed on port 3, port 3 can
interfere with their communication by spoofed src mac address with
vlan id 10.
Note: Even if it is judged that a frame should not be learned, it should
not be dropped because it is destined for not forwarding layer but higher
layer. See IEEE 802.1Q-2011 8.13.10.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-06-02
Please pull this remaining batch of updates intended for the 3.16 stream...
For the mac80211 bits, Johannes says:
"The remainder for -next right now is mostly fixes, and a handful of
small new things like some CSA infrastructure, the regdb script mW/dBm
conversion change and sending wiphy notifications."
For the bluetooth bits, Gustavo says:
"Some more patches for 3.16. There is nothing really special here, just a
bunch of clean ups, fixes plus some small improvements. Please pull."
For the nfc bits, Samuel says:
"We have:
- Felica (Type3) tags support for trf7970a
- Type 4b tags support for port100
- st21nfca DTS typo fix
- A few sparse warning fixes"
For the atheros bits, Kalle says:
"Ben added support for setting antenna configurations. Michal improved
warm reset so that we would not need to fall back to cold reset that
often, an issue where ath10k stripped protected flag while in monitor
mode and made module initialisation asynchronous to fix the problems
with firmware loading when the driver is linked to the kernel.
Luca removed unused channel_switch_beacon callbacks both from ath9k and
ath10k. Marek fixed Protected Management Frames (PMF) when using Action
Frames. Also we had other small fixes everywhere in the driver."
Along with that, there are a handful of updates to a variety
of drivers. This includes updates to at76c50x-usb, ath9k, b43,
brcmfmac, mwifiex, rsi, rtlwifi, and wil6210.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ideally, we would need to generate IP ID using a per destination IP
generator.
linux kernels used inet_peer cache for this purpose, but this had a huge
cost on servers disabling MTU discovery.
1) each inet_peer struct consumes 192 bytes
2) inetpeer cache uses a binary tree of inet_peer structs,
with a nominal size of ~66000 elements under load.
3) lookups in this tree are hitting a lot of cache lines, as tree depth
is about 20.
4) If server deals with many tcp flows, we have a high probability of
not finding the inet_peer, allocating a fresh one, inserting it in
the tree with same initial ip_id_count, (cf secure_ip_id())
5) We garbage collect inet_peer aggressively.
IP ID generation do not have to be 'perfect'
Goal is trying to avoid duplicates in a short period of time,
so that reassembly units have a chance to complete reassembly of
fragments belonging to one message before receiving other fragments
with a recycled ID.
We simply use an array of generators, and a Jenkin hash using the dst IP
as a key.
ipv6_select_ident() is put back into net/ipv6/ip6_output.c where it
belongs (it is only used from this file)
secure_ip_id() and secure_ipv6_id() no longer are needed.
Rename ip_select_ident_more() to ip_select_ident_segs() to avoid
unnecessary decrement/increment of the number of segments.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change provides a function to be used in order to break the
ndo_set_rx_mode call into a set of address add and remove calls. The code
is based on the implementation of dev_uc_sync/dev_mc_sync. Since they
essentially do the same thing but with only one dev I simply named my
functions __dev_uc_sync/__dev_mc_sync.
I also implemented an unsync version of the functions as well to allow for
cleanup on close.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix a off by one error while fragmentation. If the frag_cap
value is equal to skb_unprocessed value we need to stop the
fragmentation loop because the last fragment which has a size of
skb_unprocessed fits into the frag capability size.
This issue was introduced by commit d4b2816d67
("6lowpan: fix fragmentation").
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the 6LoWPAN fragmentation for the case if we have exactly
two fragments. The problem is that the (skb_unprocessed >= frag_cap)
condition is always false on the second fragment after sending the first
fragment. A fragmentation with only one fragment doesn't make any sense.
The solution is that we use a do while loop here, that ensures we sending
always a minimum of two fragments if we need a fragmentation.
This issue was introduced by commit d4b2816d67
("6lowpan: fix fragmentation").
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the local variable ops and n_ops were just read out from family,
and not changed, hence no need to assign back.
Validation functions should operate on const parameters and not
change anything.
Signed-off-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-[0x01 Introduction
We have found a programming error causing a deadlock in Bluetooth subsystem
of Linux kernel. The problem is caused by missing release_sock() call when
L2CAP connection creation fails due full accept queue.
The issue can be reproduced with 3.15-rc5 kernel and is also present in
earlier kernels.
-[0x02 Details
The problem occurs when multiple L2CAP connections are created to a PSM which
contains listening socket (like SDP) and left pending, for example,
configuration (the underlying ACL link is not disconnected between
connections).
When L2CAP connection request is received and listening socket is found the
l2cap_sock_new_connection_cb() function (net/bluetooth/l2cap_sock.c) is called.
This function locks the 'parent' socket and then checks if the accept queue
is full.
1178 lock_sock(parent);
1179
1180 /* Check for backlog size */
1181 if (sk_acceptq_is_full(parent)) {
1182 BT_DBG("backlog full %d", parent->sk_ack_backlog);
1183 return NULL;
1184 }
If case the accept queue is full NULL is returned, but the 'parent' socket
is not released. Thus when next L2CAP connection request is received the code
blocks on lock_sock() since the parent is still locked.
Also note that for connections already established and waiting for
configuration to complete a timeout will occur and l2cap_chan_timeout()
(net/bluetooth/l2cap_core.c) will be called. All threads calling this
function will also be blocked waiting for the channel mutex since the thread
which is waiting on lock_sock() alread holds the channel mutex.
We were able to reproduce this by sending continuously L2CAP connection
request followed by disconnection request containing invalid CID. This left
the created connections pending configuration.
After the deadlock occurs it is impossible to kill bluetoothd, btmon will not
get any more data etc. requiring reboot to recover.
-[0x03 Fix
Releasing the 'parent' socket when l2cap_sock_new_connection_cb() returns NULL
seems to fix the issue.
Signed-off-by: Jukka Taimisto <jtt@codenomicon.com>
Reported-by: Tommi Mäkilä <tmakila@codenomicon.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Use GFP_ATOMIC allocations when sending removal notifications of
anonymous sets from rcu callback context. Sleeping in that context
is illegal.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Three changes to allow the deletion of several objects with dependencies
in one transaction, they are:
1) Introduce speculative counter increment/decrement that is undone in
the abort path if required, thus we avoid hitting -EBUSY when deleting
the chain. The counter updates are reverted in the abort path.
2) Increment/decrement table/chain use counter for each set/rule. We need
this to fully rely on the use counters instead of the list content,
eg. !list_empty(&chain->rules) which evaluate true in the middle of the
transaction.
3) Decrement table use counter when an anonymous set is bound to the
rule in the commit path. This avoids hitting -EBUSY when deleting
the table that contains anonymous sets. The anonymous sets are released
in the nf_tables_rule_destroy path. This should not be a problem since
the rule already bumped the use counter of the chain, so the bound
anonymous set reflects dependencies through the rule object, which
already increases the chain use counter.
So the general assumption after this patch is that the use counters are
bumped by direct object dependencies.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There's no rbtree rcu version yet, so let's fall back on the spinlock
to protect the concurrent access of this structure both from user
(to update the set content) and kernel-space (in the packet path).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The patch c7c32e7 ("netfilter: nf_tables: defer all object release via
rcu") indicates that we always release deleted objects in the reverse
order, but that is only needed in the abort path. These are the two
possible scenarios when releasing objects:
1) Deletion scenario in the commit path: no need to release objects in
the reverse order since userspace already ensures that dependencies are
fulfilled), ie. userspace tells us to delete rule -> ... -> rule ->
chain -> table. In this case, we have to release the objects in the
*same order* as userspace provided.
2) Deletion scenario in the abort path: we have to iterate in the reverse
order to undo what it cannot be added, ie. userspace sent us a batch
that includes: table -> chain -> rule -> ... -> rule, and that needs to
be partially undone. In this case, we have to release objects in the
reverse order to ensure that the set and chain objects point to valid
rule and table objects.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The transaction needs to be placed at the end of the commit list,
otherwise event notifications are reordered and we may crash when
releasing object via call_rcu.
This problem was introduced in 60319eb ("netfilter: nf_tables: use new
transaction infrastructure to handle elements").
Reported-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Allocation of memory need only to happen once, that is
after the proper checks on the NFACCT_FLAGS have been
done. Otherwise the code can return without freeing
already allocated memory.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When checking whether a legacy link key provides at least HIGH security
level we also need to check for FIPS level which is one step above HIGH.
This patch fixes a missing check in the hci_link_key_request_evt()
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Commit 9739eef13c ("net: filter: make BPF conversion more readable")
started to introduce helper macros similar to BPF_STMT()/BPF_JUMP()
macros from classic BPF.
However, quite some statements in the filter conversion functions
remained in the old style which gives a mixture of block macros and
non block macros in the code. This patch makes the block macros itself
more readable by using explicit member initialization, and converts
the remaining ones where possible to remain in a more consistent state.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch finally allows us to get rid of the BPF_S_* enum.
Currently, the code performs unnecessary encode and decode
workarounds in seccomp and filter migration itself when a filter
is being attached in order to overcome BPF_S_* encoding which
is not used anymore by the new interpreter resp. JIT compilers.
Keeping it around would mean that also in future we would need
to extend and maintain this enum and related encoders/decoders.
We can get rid of all that and save us these operations during
filter attaching. Naturally, also JIT compilers need to be updated
by this.
Before JIT conversion is being done, each compiler checks if A
is being loaded at startup to obtain information if it needs to
emit instructions to clear A first. Since BPF extensions are a
subset of BPF_LD | BPF_{W,H,B} | BPF_ABS variants, case statements
for extensions can be removed at that point. To ease and minimalize
code changes in the classic JITs, we have introduced bpf_anc_helper().
Tested with test_bpf on x86_64 (JIT, int), s390x (JIT, int),
arm (JIT, int), i368 (int), ppc64 (JIT, int); for sparc we
unfortunately didn't have access, but changes are analogous to
the rest.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Chema Gonzalez <chemag@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There has been a number incidents recently where customers running KVM have
reported that VM hosts on different Hypervisors are unreachable. Based on
pcap traces we found that the bridge was broadcasting the ARP request out
onto the network. However some NICs have an inbuilt switch which on occasions
were broadcasting the VMs ARP request back through the physical NIC on the
Hypervisor. This resulted in the bridge changing ports and incorrectly learning
that the VMs mac address was external. As a result the ARP reply was directed
back onto the external network and VM never updated it's ARP cache. This patch
will notify the bridge command, after a fdb has been updated to identify such
port toggling.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As commit 2796d0c648 ("bridge: Automatically manage port
promiscuous mode."), make the add_if use dev_set_allmulti
instead of dev_set_promiscuous, so when add_if failed, we
should do dev_set_allmulti(dev, -1).
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Reviewed-by: Amos Kong <akong@redhat.com>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After 1e785f48d2 ("net: Start with correct mac_len in
skb_network_protocol") skb->mac_len is used as a start of the
calculation in skb_network_protocol() but that is not always correct. If
skb->protocol == 8021Q/AD, usually the vlan header is already inserted
in the skb (i.e. vlan reorder hdr == 0). Usually when the packet enters
dev_hard_xmit it has mac_len == 0 so we take 2 bytes from the
destination mac address (skb->data + VLAN_HLEN) as a type in
skb_network_protocol() and return vlan_depth == 4. In the case where TSO is
off, then the mac_len is set but it's == 18 (ETH_HLEN + VLAN_HLEN), so
skb_network_protocol() returns a type from inside the packet and
offset == 22. Also make vlan_depth unsigned as suggested before.
As suggested by Eric Dumazet, move the while() loop in the if() so we
can avoid additional testing in fast path.
Here are few netperf tests + debug printk's to illustrate:
cat netperf.tso-on.reorder-on.bugged
- Vlan -> device (reorder on, default, this case is okay)
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
192.168.3.1 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 7111.54
[ 81.605435] skb->len 65226 skb->gso_size 1448 skb->proto 0x800
skb->mac_len 0 vlan_depth 0 type 0x800
- Vlan -> device (reorder off, bad)
cat netperf.tso-on.reorder-off.bugged
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
192.168.3.1 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 241.35
[ 204.578332] skb->len 1518 skb->gso_size 0 skb->proto 0x8100
skb->mac_len 0 vlan_depth 4 type 0x5301
0x5301 are the last two bytes of the destination mac.
And if we stop TSO, we may get even the following:
[ 83.343156] skb->len 2966 skb->gso_size 1448 skb->proto 0x8100
skb->mac_len 18 vlan_depth 22 type 0xb84
Because mac_len already accounts for VLAN_HLEN.
After the fix:
cat netperf.tso-on.reorder-off.fixed
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
192.168.3.1 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.01 5001.46
[ 81.888489] skb->len 65230 skb->gso_size 1448 skb->proto 0x8100
skb->mac_len 0 vlan_depth 18 type 0x800
CC: Vlad Yasevich <vyasevic@redhat.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Daniel Borkman <dborkman@redhat.com>
CC: David S. Miller <davem@davemloft.net>
Fixes:1e785f48d29a ("net: Start with correct mac_len in
skb_network_protocol")
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to recent changes to the way that the MITM requirement is set for
outgoing pairing attempts we can no longer rely on the hcon->auth_type
variable (which is actually good since it was formed from BR/EDR
concepts that don't really exist for SMP).
To match the logic that BR/EDR now uses simply rely on the local IO
capability and/or needed security level to set the MITM requirement for
outgoing pairing requests.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
- prevent NULL dereference in multicast code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=fvfu
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- prevent NULL dereference in multicast code
Antonion Quartulli says:
====================
pull request net: batman-adv 20140527
here you have another very small fix intended for net/linux-3.15.
It prevents some multicast functions from dereferencing a NULL pointer.
(Actually it was nothing more than a typo)
I hope it is not too late for such a small patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Was introduced with 4c8755d69c
("batman-adv: Send multicast packets to nodes with a WANT_ALL flag")
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Default values for various channel settings were missing. This
way channel users do not need to set default values themselves.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The universal/local bit handling was incorrectly done in the code.
So when setting EUI address from BD address we do this:
- If BD address type is PUBLIC, then we clear the universal bit
in EUI address. If the address type is RANDOM, then the universal
bit is set (BT 6lowpan draft chapter 3.2.2)
- After this we invert the universal/local bit according to RFC 2464
When figuring out BD address we do the reverse:
- Take EUI address from stateless IPv6 address, invert the
universal/local bit according to RFC 2464
- If universal bit is 1 in this modified EUI address, then address
type is set to RANDOM, otherwise it is PUBLIC
Note that 6lowpan_iphc.[ch] does the final toggling of U/L bit
before sending or receiving the network packet.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
When checking whether we need to request authentication or not we should
include HCI_SECURITY_FIPS to the levels that always need authentication.
This patch fixes check for it in the hci_outgoing_auth_needed()
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
In case there are new LTK types in the future we shouldn't just blindly
assume that != MGMT_LTK_UNAUTHENTICATED means that the key is
authenticated. This patch adds explicit checks for each allowed key type
in the form of a switch statement and skips any key which has an unknown
value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Pablo Neira Ayuso says:
====================
The following patchset contains a late fix for IPVS:
* Fix crash when trying to remove the transport header with non-linear
skbuffs, this was introduced in 3.6-rc. Patch from Peter Christensen
via the IPVS folks.
I'll pass this to -stable once this hits mainstream.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
This small patchset contains three accumulated Netfilter/IPVS updates,
they are:
1) Refactorize common NAT code by encapsulating it into a helper
function, similarly to what we do in other conntrack extensions,
from Florian Westphal.
2) A minor format string mismatch fix for IPVS, from Masanari Iida.
3) Add quota support to the netfilter accounting infrastructure, now
you can add quotas to accounting objects via the nfnetlink interface
and use them from iptables. You can also listen to quota
notifications from userspace. This enhancement from Mathieu Poirier.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces a comma between expression statements by a semicolon.
A simplified version of the semantic patch that performs this
transformation is as follows:
// <smpl>
@r@
expression e1,e2,e;
type T;
identifier i;
@@
e1
-,
+;
e2;
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces a comma between expression statements by a semicolon.
A simplified version of the semantic patch that performs this
transformation is as follows:
// <smpl>
@r@
expression e1,e2,e;
type T;
identifier i;
@@
e1
-,
+;
e2;
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces a comma between expression statements by a semicolon.
A simplified version of the semantic patch that performs this
transformation is as follows:
// <smpl>
@r@
expression e1,e2,e;
type T;
identifier i;
@@
e1
-,
+;
e2;
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces a comma between expression statements by a semicolon.
A simplified version of the semantic patch that performs this
transformation is as follows:
// <smpl>
@r@
expression e1,e2,e;
type T;
identifier i;
@@
e1
-,
+;
e2;
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of transport HIPER a sock struct is allocated for an incoming
connect request. If the backlog queue is full this socket is not
needed, but is left in the list of af_iucv sockets. Final socket
release posts console message "Attempt to release alive iucv socket".
This patch makes sure the new created socket is cleaned up correctly
if the backlog queue is full.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Reported-by: Philipp Hachtmann <phacht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a socket is bound to an address using before calling connect
it is usual to leave it to the network system to choose an appropriate
outgoing application name respective port address.
af_iucv on VM uses a counter and uses simple numbers as unique identifiers.
This behaviour was missing when af_iucv is used with HiperSockets.
This patch contains a simple approach to harmonize af_iucv's behaviour.
Signed-off-by: Philipp Hachtmann <phacht@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When debugging, rpc prints messages from dprintk(KERN_WARNING ...)
with "^A4" prefixed,
[ 2780.339988] ^A4nfsd: connect from unprivileged port: 127.0.0.1, port=35316
Trond tells,
> dprintk != printk. We have NEVER supported dprintk(KERN_WARNING...)
This patch removes using of dprintk with KERN_WARNING.
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
John W. Linville says:
====================
Please pull this batch of updates intended for 3.16...
For the mac80211 bits, Johannes says:
"Here I just have Heikki's rfkill GPIO cleanups.
The ARM/tegra patch is OK with the maintainer (Stephen). Let me know of
any problems."
and;
"We have a whole bunch of work on CSA by Andrei, Luca and Michal, but
unfortunately it doesn't seem quite complete yet so it's still disabled.
There's some TDLS work from Arik, and the rest is mostly minor fixes and
cleanups."
For the NFC bits, Samuel says:
"This is the NFC pull request for 3.16. We have:
- STMicroeectronics st21nfca support. The st21nfca is an HCI chipset and
thus relies on the HCI stack. This submission provides support for tag
redaer/writer mode (including Type 5) and device tree bindings.
- PM runtime support and a bunch of bug fixes for TI's trf7970a.
- Device tree support for NXP's pn544. Legacy platform data support is
obviously kept intact.
- NFC Tag type 4B support to the NFC Digital stack.
- SOCK_RAW type support to the raw NFC socket, and allow NCI
sniffing from that. This can be extended to report HCI frames and also
proprietarry ones like e.g. the pn533 ones."
For the iwlwifi bits, Emmanuel says:
"Eran continues to work on new devices, Eyal is still digging in
the rate control stuff, and Johannes added new functionality to the
debug system we have in place now along with a few cleanups he made
on the way. That's pretty much it."
and;
"Avri continues to work on the power code and Eran is improving the
NVM handling as a preparations for new devices on which he works
with Liad. Luca cleans up a bit the code while working on CSA. I have
the regular BT Coex stuff and a small lockdep fix. Johannes has his
regular amount of clean ups and improvements, the main one is the
ability to leave 2 chains open to improve diversity and hence the
throughput in high attenuation scenarios."
and;
"The regular amount of housekeeping here. I merged iwlwifi-fixes.git to
be able to add the patch you didn't want in wireless.git at that stage
of the -rc cycle. Luca has a few preparations for CSA implementation
and also what seems to be a bugfix for P2P but hasn't caused issues
we could notice."
For the Atheros bits, Kalle says:
"For ath10k Michal did various small fixes on how we handle
hardware/firmware problems and he also fixed two memory leaks."
Also included are a couple of pulls from the wireless tree to
avoid/resolve merge issues...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This preprocessor check is commented out ever since this file was added
during the v2.3 development cycle. It is unclear what it purpose might
have been. Whatever it was, it can safely be removed now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
RPC_MAX_AUTH_SIZE is scattered around several places. Better to set it
once in the auth code, where this kind of estimate should be made. And
while we're at it we can leave it zero when we're not using krb5i or
krb5p.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
After this we can handle for example getattr of very large ACLs.
Read, readdir, readlink are still special cases with their own limits.
Also we can't handle a new operation starting close to the end of a
page.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This will be used in the server side in a few cases:
- when certain operations (read, readdir, readlink) fail after
encoding a partial response.
- when we run out of space after encoding a partial response.
- in readlink, where we initially reserve PAGE_SIZE bytes for
data, then truncate to the actual size.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This is the 2nd NFC pull request for 3.16. We have:
- Felica (Type3) tags support for trf7970a
- Type 4b tags support for port100
- st21nfca DTS typo fix
- A few sparse warning check fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t52d
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.16: Second pull request
This is the 2nd NFC pull request for 3.16. We have:
- Felica (Type3) tags support for trf7970a
- Type 4b tags support for port100
- st21nfca DTS typo fix
- A few sparse warning check fixes"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark new interfaces as idle to allow operations that require that
interfaces are idle to take place. Interface types that are always
not idle (like AP interfaces) will be set as not idle when they are
assigned a channel context.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach<emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During strong signal fluctuations under high throughput, few consecutive
failed A-MPDU transmissions can easily trigger packet loss notification,
and thus (in AP mode) client disconnection.
Reduce the number of false positives by checking the A-MPDU status flag
and treating a failed A-MPDU as a single packet.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Doing so will lead to an oops for a p2p-dev interface, since it has
no netdev.
Cc: stable@vger.kernel.org
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the rate control algorithm uses a selection table, it
is leaked when the station is destroyed - fix that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Christophe Prévotaux <cprevotaux@nltinc.com>
Fixes: 0d528d85c5 ("mac80211: improve the rate control API")
Cc: stable@vger.kernel.org # v3.10+
[add commit log entry, remove pointless NULL check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Generalize the power conversion from mW to dBm
using log. This should fix the below compilation
error for country NO which adds a new power value
2000mW which is not handled earlier.
CC [M] net/wireless/wext-sme.o
CC [M] net/wireless/regdb.o
net/wireless/regdb.c:1130:1: error: Unknown undeclared here (not in
a function)
net/wireless/regdb.c:1130:9: error: expected } before power
make[2]: *** [net/wireless/regdb.o] Error 1
make[1]: *** [net/wireless] Error 2
make: *** [net] Error 2
Reported-By: John Walker <john@x109.net>
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
[remove unneeded parentheses, fix rounding by using %.0f]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Without this fix, freshly rebooted Linux creates a new IBSS
instead of joining an existing one. Only when jiffies counter
overflows after 5 minutes the IBSS can be successfully joined.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
[edit commit message slightly]
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We're currently sending NEW_WIPHY events for renames (which
is a bit odd, but now can't be changed), but also send them
for really new devices that register.
Also send DEL_WIPHY events when a device is removed, the
event ID for this was already reserved.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the commit below, cfg80211_chandef_dfs_required()
will warn if it gets a an NL80211_IFTYPE_UNSPECIFIED iftype
as explicitely written in the commit log.
When an virtual monitor interface is added, its type is set
in ieee80211_sub_if_data.vif.type, but not in
ieee80211_sub_if_data.wdev.iftype which is passed to
cfg80211_chandef_dfs_required() hence resulting in the
following warning:
WARNING: CPU: 1 PID: 21265 at net/wireless/chan.c:376 cfg80211_chandef_dfs_required+0xbc/0x130 [cfg80211]()
Modules linked in: [...]
CPU: 1 PID: 21265 Comm: ifconfig Tainted: G W O 3.13.11+ #12
Hardware name: Dell Inc. Latitude E6410/0667CC, BIOS A01 03/05/2010
0000000000000009 ffff88008f5fdb08 ffffffff817d4219 ffff88008f5fdb50
ffff88008f5fdb40 ffffffff8106f57d 0000000000000000 0000000000000000
ffff880081062fb8 ffff8800810604e0 0000000000000001 ffff88008f5fdba0
Call Trace:
[<ffffffff817d4219>] dump_stack+0x4d/0x66
[<ffffffff8106f57d>] warn_slowpath_common+0x7d/0xa0
[<ffffffff8106f5ec>] warn_slowpath_fmt+0x4c/0x50
[<ffffffffa04ea4ec>] cfg80211_chandef_dfs_required+0xbc/0x130 [cfg80211]
[<ffffffffa06b1024>] ieee80211_vif_use_channel+0x94/0x500 [mac80211]
[<ffffffffa0684e6b>] ieee80211_add_virtual_monitor+0x1ab/0x5c0 [mac80211]
[<ffffffffa0686ae5>] ieee80211_do_open+0xe75/0x1580 [mac80211]
[<ffffffffa0687259>] ieee80211_open+0x69/0x70 [mac80211]
[snip]
Fixes: 00ec75fc5a ("cfg80211: pass the actual iftype when calling cfg80211_chandef_dfs_required()")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, when the driver is already using all the channel
contexts it can handle at once, we have to do an in-place switch
(ie. we cannot afford using an extra context temporarily for the
transaction). But some drivers may not support switching the channel
context assigned to a vif on the fly (ie. without unassigning and
assigning it) while others may only work if the context is changed on
the fly, without unassigning it first.
To allow these different scenarios, add a new driver operation that
let's the driver decide how to handle an in-place switch.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Before f5efc69 ("netfilter: nf_tables: Add meta expression key for
bridge interface name"), the entire net/bridge/netfilter/ directory
depended on BRIDGE_NF_EBTABLES, ie. on ebtables. However, that
directory already contained the nf_tables bridge extension that
we should allow to compile separately. In f5efc69, we tried to
generalize this by using CONFIG_BRIDGE_NETFILTER which was not a good
idea since this option already existed and it is dedicated to enable
the Netfilter bridge IP/ARP filtering.
Let's try to fix this mess by:
1) making net/bridge/netfilter/ dependent on the toplevel
CONFIG_NETFILTER option, just like we do with the net/netfilter and
net/ipv{4,6}/netfilter/ directories.
2) Changing 'selects' to 'depends on' NETFILTER_XTABLES for
BRIDGE_NF_EBTABLES. I believe this problem was already before
f5efc69:
warning: (BRIDGE_NF_EBTABLES) selects NETFILTER_XTABLES which has
unmet direct dependencies (NET && INET && NETFILTER)
3) Fix ebtables/nf_tables bridge dependencies by making NF_TABLES_BRIDGE
and BRIDGE_NF_EBTABLES dependent on BRIDGE and NETFILTER:
warning: (NF_TABLES_BRIDGE && BRIDGE_NF_EBTABLES) selects
BRIDGE_NETFILTER which has unmet direct dependencies (NET && BRIDGE &&
NETFILTER && INET && NETFILTER_ADVANCED)
net/built-in.o: In function `br_parse_ip_options':
br_netfilter.c:(.text+0x4a5ba): undefined reference to `ip_options_compile'
br_netfilter.c:(.text+0x4a5ed): undefined reference to `ip_options_rcv_srr'
net/built-in.o: In function `br_nf_pre_routing_finish':
br_netfilter.c:(.text+0x4a8a4): undefined reference to `ip_route_input_noref'
br_netfilter.c:(.text+0x4a987): undefined reference to `ip_route_output_flow'
make: *** [vmlinux] Error 1
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receiving a ICMP response to an IPIP packet in a non-linear skb could
cause a kernel panic in __skb_pull.
The problem was introduced in
commit f2edb9f770 ("ipvs: implement
passive PMTUD for IPIP packets").
Signed-off-by: Peter Christensen <pch@ordbogen.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
This change adds some entropy to polling cycles, choosing the next
polling rf technology randomly. This reflects the change done in the
pn533 driver, avoiding possible infinite loop for devices that export 2
targets on 2 different modulations. If the first target is not
readable, we will stay in an error loop for ever.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The error code returned by digital_in_send_cmd() was not returned by
digital_in_send_atr_req().
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As it may then take longer than what the user specified using
setsockopt(SO_RCVTIMEO).
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-05-23
I have two more fixes intended for the 3.15 stream...
For the iwlwifi one, Emmanuel says:
"A race has been discovered in the beacon filtering code. Since the
fix is too big for 3.15, I disable here the feature."
For the bluetooth one, Gustavo says:
"This pull request contains a very important fix for 3.15. Here we fix the
permissions of a debugfs file that would otherwise allow unauthorized users
to write content to it."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"It looks like a sizeble collection but this is nearly 3 weeks of bug
fixing while you were away.
1) Fix crashes over IPSEC tunnels with NAT, the latter can reroute
the packet through a non-IPSEC protected path and the code has to
be able to handle SKBs attached to routes lacking an attached xfrm
state. From Steffen Klassert.
2) Fix OOPSs in ipv4 and ipv6 ipsec layers for unsupported
sub-protocols, also from Steffen Klassert.
3) Set local_df on fragmented netfilter skbs otherwise we won't be
able to forward successfully, from Florian Westphal.
4) cdc_mbim ipv6 neighbour code does __vlan_find_dev_deep without
holding RCU lock, from Bjorn Mork.
5) local_df test in ip_may_fragment is inverted, from Florian
Westphal.
6) jme driver doesn't check for DMA mapping failures, from Neil
Horman.
7) qlogic driver doesn't calculate number of TX queues properly, from
Shahed Shaikh.
8) fib_info_cnt can drift irreversibly positive if we fail to
allocate the fi->fib_metrics array, from Sergey Popovich.
9) Fix use after free in ip6_route_me_harder(), also from Sergey
Popovich.
10) When SYSCTL is disabled, we don't handle local_port_range and
ping_group_range defaults properly at all, from Cong Wang.
11) Unaccelerated VLAN tagged frames improperly handled by cdc_mbim
driver, fix from Bjorn Mork.
12) cassini driver needs nested lock annotations for TX locking, from
Emil Goode.
13) On init error ipv6 VTI driver can unregister pernet ops twice,
oops. Fix from Mahtias Krause.
14) If macvlan device is down, don't propagate IFF_ALLMULTI changes,
from Peter Christensen.
15) Missing NULL pointer check while parsing netlink config options in
ip6_tnl_validate(). From Susant Sahani.
16) Fix handling of neighbour entries during ipv6 router reachability
probing, from Duan Jiong.
17) x86 and s390 JIT address randomization has some address
calculation bugs leading to crashes, from Alexei Starovoitov and
Heiko Carstens.
18) Clear up those uglies with nop patching and net_get_random_once(),
from Hannes Frederic Sowa.
19) Option length miscalculated in ip6_append_data(), fix also from
Hannes Frederic Sowa.
20) A while ago we fixed a race during device unregistry when a
namespace went down, turns out there is a second place that needs
similar protection. From Cong Wang.
21) In the new Altera TSE driver multicast filtering isn't working,
disable it and just use promisc mode until the cause is found.
From Vince Bridgers.
22) When we disable router enabling in ipv6 we have to flush the
cached routes explicitly, from Duan Jiong.
23) NBMA tunnels should not cache routes on the tunnel object because
the key is variable, from Timo Teräs.
24) With stacked devices GRO information in skb->cb[] can be not setup
properly, make sure it is in all code paths. From Eric Dumazet.
25) Really fix stacked vlan locking, multiple levels of nesting with
intervening non-vlan devices are possible. From Vlad Yasevich.
26) Fallback ipip tunnel device's mtu is not setup properly, from
Steffen Klassert.
27) The packet scheduler's tcindex filter can crash because we
structure copy objects with list_head's inside, oops. From Cong
Wang.
28) Fix CHECKSUM_COMPLETE handling for ipv6 GRE tunnels, from Eric
Dumazet.
29) In some configurations 'itag' in __mkroute_input() can end up
being used uninitialized because of how fib_validate_source()
works. Fix it by explitly initializing itag to zero like all the
other fib_validate_source() callers do, from Li RongQing"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
batman: fix a bogus warning from batadv_is_on_batman_iface()
ipv4: initialise the itag variable in __mkroute_input
bonding: Send ALB learning packets using the right source
bonding: Don't assume 802.1Q when sending alb learning packets.
net: doc: Update references to skb->rxhash
stmmac: Remove unbalanced clk_disable call
ipv6: gro: fix CHECKSUM_COMPLETE support
net_sched: fix an oops in tcindex filter
can: peak_pci: prevent use after free at netdev removal
ip_tunnel: Initialize the fallback device properly
vlan: Fix build error wth vlan_get_encap_level()
can: c_can: remove obsolete STRICT_FRAME_ORDERING Kconfig option
MAINTAINERS: Pravin Shelar is Open vSwitch maintainer.
bnx2x: Convert return 0 to return rc
bonding: Fix alb mode to only use first level vlans.
bonding: Fix stacked device detection in arp monitoring
macvlan: Fix lockdep warnings with stacked macvlan devices
vlan: Fix lockdep warning with stacked vlan devices.
net: Allow for more then a single subclass for netif_addr_lock
net: Find the nesting level of a given device by type.
...
The sk_unattached_filter_create() API is used by BPF filters that
are not directly attached or related to sockets, and are used in
team, ptp, xt_bpf, cls_bpf, etc. As such all users do their own
internal managment of obtaining filter blocks and thus already
have them in kernel memory and set up before calling into
sk_unattached_filter_create(). As a result, due to __user annotation
in sock_fprog, sparse triggers false positives (incorrect type in
assignment [different address space]) when filters are set up before
passing them to sk_unattached_filter_create(). Therefore, let
sk_unattached_filter_create() API use sock_fprog_kern to overcome
this issue.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lets get rid of this macro. After commit 5bcfedf06f ("net: filter:
simplify label names from jump-table"), labels have become more
readable due to omission of BPF_ prefix but at the same time more
generic, so that things like `git grep -n` would not find them. As
a middle path, lets get rid of the DL macro as it's not strictly
needed and would otherwise just hide the full name.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added new L2TP configuration options to allow TX and RX of
zero checksums in IPv6. Default is not to use them.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 6935 permits zero checksums to be used in IPv6 however this is
recommended only for certain tunnel protocols, it does not make
checksums completely optional like they are in IPv4.
This patch restricts the use of IPv6 zero checksums that was previously
intoduced. no_check6_tx and no_check6_rx have been added to control
the use of checksums in UDP6 RX and TX path. The normal
sk_no_check_{rx,tx} settings are not used (this avoids ambiguity when
dealing with a dual stack socket).
A helper function has been added (udp_set_no_check6) which can be
called by tunnel impelmentations to all zero checksums (send on the
socket, and accept them as valid).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define separate fields in the sock structure for configuring disabling
checksums in both TX and RX-- sk_no_check_tx and sk_no_check_rx.
The SO_NO_CHECK socket option only affects sk_no_check_tx. Also,
removed UDP_CSUM_* defines since they are no longer necessary.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't seem like an protocols are setting anything other
than the default, and allowing to arbitrarily disable checksums
for a whole protocol seems dangerous. This can be done on a per
socket basis.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting sk_no_check to UDP_CSUM_NORCV seems to have no effect.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
to have a bandwidth of at least this value.
max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
of up to this value.
o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
which takes 4 arguments:
netdev, VF number, min_tx_rate, max_tx_rate
o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.
o Drivers that currently implement ndo_set_vf_tx_rate should now call
ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
implemented by driver.
o If user enters only one of either min_tx_rate or max_tx_rate, then,
userland should read back the other value from driver and set both
for IFLA_VF_RATE.
Drivers that have not yet implemented IFLA_VF_RATE should always
return min_tx_rate as 0 when read from ip tool.
o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
IFLA_VF_RATE should override.
o Idea is to have consistent display of rate values to user.
o Usage example: -
./ip link set p4p1 vf 0 rate 900
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 600 rate 300
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the mgmt level we have a key type parameter which currently accepts
two possible values: 0x00 for unauthenticated and 0x01 for
authenticated. However, in the internal struct smp_ltk representation we
have an explicit "authenticated" boolean value.
To make this distinction clear, add defines for the possible mgmt values
and do conversion to and from the internal authenticated value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Following patch get rid of struct genl_family_and_ops which is
redundant due to changes to struct genl_family.
Signed-off-by: Kyle Mestery <mestery@noironetworks.com>
Acked-by: Kyle Mestery <mestery@noironetworks.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Following patch will be easier to reason about with separate
ovs_flow_cmd_new() and ovs_flow_cmd_set() functions.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
ovs_flow_cmd_del() now allocates reply (if needed) after the flow has
already been removed from the flow table. If the reply allocation
fails, a netlink error is signaled with netlink_set_err(), as is
already done in ovs_flow_cmd_new_or_set() in the similar situation.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reduce and clarify locking requirements for ovs_flow_cmd_alloc_info(),
ovs_flow_cmd_fill_info() and ovs_flow_cmd_build_info().
A datapath pointer is available only when holding a lock. Change
ovs_flow_cmd_fill_info() and ovs_flow_cmd_build_info() to take a
dp_ifindex directly, rather than a datapath pointer that is then
(only) used to get the dp_ifindex. This is useful, since the
dp_ifindex is available even when the datapath pointer is not, both
before and after taking a lock, which makes further critical section
reduction possible.
Make ovs_flow_cmd_alloc_info() take an 'acts' argument instead a
'flow' pointer. This allows some future patches to do the allocation
before acquiring the flow pointer.
The locking requirements after this patch are:
ovs_flow_cmd_alloc_info(): May be called without locking, must not be
called while holding the RCU read lock (due to memory allocation).
If 'acts' belong to a flow in the flow table, however, then the
caller must hold ovs_mutex.
ovs_flow_cmd_fill_info(): Either ovs_mutex or RCU read lock must be held.
ovs_flow_cmd_build_info(): This calls both of the above, so the caller
must hold ovs_mutex.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
For ovs_flow_stats_get() using ovsl_dereference() was wrong, since
flow dumps call this with RCU read lock.
ovs_flow_stats_clear() is always called with ovs_mutex, so can use
ovsl_dereference().
Also, make the ovs_flow_stats_get() 'flow' argument const to make
later patches cleaner.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Incorrect struct name was confusing, even though otherwise
inconsequental.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Move most memory allocations away from the ovs_mutex critical
sections. vport allocations still happen while the lock is taken, as
changing that would require major refactoring. Also, vports are
created very rarely so it should not matter.
Change ovs_dp_cmd_get() now only takes the rcu_read_lock(), rather
than ovs_lock(), as nothing need to be changed. This was done by
ovs_vport_cmd_get() already.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Masks are inserted when flows are inserted to the table, so it is
logical to correspondingly remove masks when flows are removed from
the table, in ovs_flow_table_remove().
This allows ovs_flow_free() to be called without locking, which will
be used by later patches.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Use netlink_has_listeners() and NLM_F_ECHO flag to determine if a
reply is needed or not for OVS_FLOW_CMD_NEW, OVS_FLOW_CMD_SET, or
OVS_FLOW_CMD_DEL. Currently, OVS userspace does not request a reply
for OVS_FLOW_CMD_NEW, but usually does for OVS_FLOW_CMD_DEL, as stats
may have changed.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Remove unnecessary locking from functions that are always called with
appropriate locking.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Thomas Graf <tgraf@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Flow SET can accept an empty set of actions, with the intended
semantics of leaving existing actions unmodified. This seems to have
been brokin after OVS 1.7, as we have assigned the flow's actions
pointer to NULL in this case, but we never check for the NULL pointer
later on. This patch restores the intended behavior and documents it
in the include/linux/openvswitch.h.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Minimize padding in sw_flow_key and move 'tp' top the main struct.
These changes simplify code when accessing the transport port numbers
and the tcp flags, and makes the sw_flow_key 8 bytes smaller on 64-bit
systems (128->120 bytes). These changes also make the keys for IPv4
packets to fit in one cache line.
There is a valid concern for safety of packing the struct
ovs_key_ipv4_tunnel, as it would be possible to take the address of
the tun_id member as a __be64 * which could result in unaligned access
in some systems. However:
- sw_flow_key itself is 64-bit aligned, so the tun_id within is
always
64-bit aligned.
- We never make arrays of ovs_key_ipv4_tunnel (which would force
every
second tun_key to be misaligned).
- We never take the address of the tun_id in to a __be64 *.
- Whereever we use struct ovs_key_ipv4_tunnel outside the
sw_flow_key,
it is in stack (on tunnel input functions), where compiler has full
control of the alignment.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
batman tries to search dev->iflink to check if it's a batman interface,
but ->iflink could be 0, which is not a valid ifindex. It should just
avoid iflink == 0 case.
Reported-by: Jet Chen <jet.chen@intel.com>
Tested-by: Jet Chen <jet.chen@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Antonio Quartulli <antonio@open-mesh.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2014-05-22
This is the last ipsec pull request before I leave for
a three weeks vacation tomorrow. David, can you please
take urgent ipsec patches directly into net/net-next
during this time?
I'll continue to run the ipsec/ipsec-next trees as soon
as I'm back.
1) Simplify the xfrm audit handling, from Tetsuo Handa.
2) Codingstyle cleanup for xfrm_output, from abian Frederick.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If an incoming NFS request is coming from the local host, then
nfsd will need to perform some special handling. So detect that
possibility and make the source visible in rq_local.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
the value of itag is a random value from stack, and may not be initiated by
fib_validate_source, which called fib_combine_itag if CONFIG_IP_ROUTE_CLASSID
is not set
This will make the cached dst uncertainty
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the accept() call fails, we need to put the module reference.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
An NFS/RDMA client's source port is meaningless for RDMA transports.
The transport layer typically sets the source port value on the
connection to a random ephemeral port.
Currently, NFS server administrators must specify the "insecure"
export option to enable clients to access exports via RDMA.
But this means NFS clients can access such an export via IP using an
ephemeral port, which may not be desirable.
This patch eliminates the need to specify the "insecure" export
option to allow NFS/RDMA clients access to an export.
BugLink: https://bugzilla.linux-nfs.org/show_bug.cgi?id=250
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
We should call put_dev() on the error path here.
Fixes: 3e9c156e2c ('ieee802154: add netlink interfaces for llsec')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge net/bridge/br_notify.c into net/bridge/br.c,
since it has only br_device_event() and br.c is small.
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'dccp_timestamp_seed' is initialized once by ktime_get_real() in
dccp_timestamping_init(). It is always less than ktime_get_real()
in dccp_timestamp().
Then, ktime_us_delta() in dccp_timestamp() will always return positive
number. So can use manual type cast to let compiler and do_div() know
about it to avoid warning.
The related warning (with allmodconfig under unicore32):
CC [M] net/dccp/timer.o
net/dccp/timer.c: In function ‘dccp_timestamp’:
net/dccp/timer.c:285: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Key id comparison for type 1 keys (implicit source, with index) should
return true if mode and id are equal, not false.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
llsec_do_encrypt will never return a positive value, so the restriction
to 0-or-negative on return is useless.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In encrypt, sec->lock is taken with read_lock_bh, so in the error path,
we must read_unlock_bh.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When combining real_dev's features and vlan_features, simple
bitwise AND is used. This doesn't work well for checksum
offloading features as if one set has NETIF_F_HW_CSUM and the
other NETIF_F_IP_CSUM and/or NETIF_F_IPV6_CSUM, we end up with
no checksum offloading. However, from the logical point of view
(how can_checksum_protocol() works), NETIF_F_HW_CSUM contains
the functionality of NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM so
that the result should be IP/IPV6.
Add helper function netdev_intersect_features() implementing
this logic and use it in vlan_dev_fix_features().
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although the implementation probably needs a lot of work, this initial API
allows to implement software TSO in mvneta and mv643xx_eth drivers in a not
so intrusive way.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the NFC pull request for 3.16. We have:
- STMicroeectronics st21nfca support. The st21nfca is an HCI chipset and
thus relies on the HCI stack. This submission provides support for tag
redaer/writer mode (including Type 5) and device tree bindings.
- PM runtime support and a bunch of bug fixes for TI's trf7970a.
- Device tree support for NXP's pn544. Legacy platform data support is
obviously kept intact.
- NFC Tag type 4B support to the NFC Digital stack.
- SOCK_RAW type support to the raw NFC socket, and allow NCI
sniffing from that. This can be extended to report HCI frames and also
proprietarry ones like e.g. the pn533 ones.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cSl+
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.16: First pull request
This is the NFC pull request for 3.16. We have:
- STMicroeectronics st21nfca support. The st21nfca is an HCI chipset and
thus relies on the HCI stack. This submission provides support for tag
redaer/writer mode (including Type 5) and device tree bindings.
- PM runtime support and a bunch of bug fixes for TI's trf7970a.
- Device tree support for NXP's pn544. Legacy platform data support is
obviously kept intact.
- NFC Tag type 4B support to the NFC Digital stack.
- SOCK_RAW type support to the raw NFC socket, and allow NCI
sniffing from that. This can be extended to report HCI frames and also
proprietarry ones like e.g. the pn533 ones."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pablo Neira Ayuso says:
====================
Netfilter/nftables updates for net-next
The following patchset contains Netfilter/nftables updates for net-next,
most relevantly they are:
1) Add set element update notification via netlink, from Arturo Borrero.
2) Put all object updates in one single message batch that is sent to
kernel-space. Before this patch only rules where included in the batch.
This series also introduces the generic transaction infrastructure so
updates to all objects (tables, chains, rules and sets) are applied in
an all-or-nothing fashion, these series from me.
3) Defer release of objects via call_rcu to reduce the time required to
commit changes. The assumption is that all objects are destroyed in
reverse order to ensure that dependencies betweem them are fulfilled
(ie. rules and sets are destroyed first, then chains, and finally
tables).
4) Allow to match by bridge port name, from Tomasz Bursztyka. This series
include two patches to prepare this new feature.
5) Implement the proper set selection based on the characteristics of the
data. The new infrastructure also allows you to specify your preferences
in terms of memory and computational complexity so the underlying set
type is also selected according to your needs, from Patrick McHardy.
6) Several cleanup patches for nft expressions, including one minor possible
compilation breakage due to missing mark support, also from Patrick.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Experience with the recent e114a710aa ("tcp: fix cwnd limited
checking to improve congestion control") has shown that there are
common cases where that commit can cause cwnd to be much larger than
necessary. This leads to TSO autosizing cooking skbs that are too
large, among other things.
The main problems seemed to be:
(1) That commit attempted to predict the future behavior of the
connection by looking at the write queue (if TSO or TSQ limit
sending). That prediction sometimes overestimated future outstanding
packets.
(2) That commit always allowed cwnd to grow to twice the number of
outstanding packets (even in congestion avoidance, where this is not
needed).
This commit improves both of these, by:
(1) Switching to a measurement-based approach where we explicitly
track the largest number of packets in flight during the past window
("max_packets_out"), and remember whether we were cwnd-limited at the
moment we finished sending that flight.
(2) Only allowing cwnd to grow to twice the number of outstanding
packets ("max_packets_out") in slow start. In congestion avoidance
mode we now only allow cwnd to grow if it was fully utilized.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Channels in 2.4GHz band overlap, this means that if we
send a probe request on channel 1 and then move to channel
2, we will hear the probe response on channel 2. In this
case, the RSSI will be lower than if we had heard it on
the channel on which it was sent (1 in this case).
The firmware / low level driver can parse the channel in
the DS IE or HT IE and compensate the RSSI so that it will
still have a valid value even if we heard the frame on an
adjacent channel. This can be done up to a certain offset.
Add this offset as a configuration for the low level driver.
A low level driver that can compensate the low RSSI in this
case should assign the maximal offset for which the RSSI
value is still valid.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When GRE support was added in linux-3.14, CHECKSUM_COMPLETE handling
broke on GRE+IPv6 because we did not update/use the appropriate csum :
GRO layer is supposed to use/update NAPI_GRO_CB(skb)->csum instead of
skb->csum
Tested using a GRE tunnel and IPv6 traffic. GRO aggregation now happens
at the first level (ethernet device) instead of being done in gre
tunnel. Native IPv6+TCP is still properly aggregated.
Fixes: bf5a755f5e ("net-gre-gro: Add GRE support to the GRO stack")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel API for classic BPF socket filters is:
sk_unattached_filter_create() - validate classic BPF, convert, JIT
SK_RUN_FILTER() - run it
sk_unattached_filter_destroy() - destroy socket filter
Cleanup internal BPF kernel API as following:
sk_filter_select_runtime() - final step of internal BPF creation.
Try to JIT internal BPF program, if JIT is not available select interpreter
SK_RUN_FILTER() - run it
sk_filter_free() - free internal BPF program
Disallow direct calls to BPF interpreter. Execution of the BPF program should
be done with SK_RUN_FILTER() macro.
Example of internal BPF create, run, destroy:
struct sk_filter *fp;
fp = kzalloc(sk_filter_size(prog_len), GFP_KERNEL);
memcpy(fp->insni, prog, prog_len * sizeof(fp->insni[0]));
fp->len = prog_len;
sk_filter_select_runtime(fp);
SK_RUN_FILTER(fp, ctx);
sk_filter_free(fp);
Sockets, seccomp, testsuite, tracing are using different ways to populate
sk_filter, so first steps of program creation are not common.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
entries is always greater than rt_max_size here, since if entries is less
than rt_max_size, the fib6_run_gc function will be skipped
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the module alias hookup to allow tunnel modules to be autoloaded on demand.
This is in line with how most other netdev kinds work, and will allow userspace
to create tunnels without having CAP_SYS_MODULE.
Signed-off-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise every "indoor" setting by usermode will cause a regdomain reset.
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement and export the new cfg80211_get_station() API.
This utility can be used by other kernel modules to obtain
detailed information about a given wireless station.
It will be in particular useful to batman-adv which will
implement a wireless rate based metric.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add get_expected_throughput() API to mac80211 so that each
driver can implement its own version based on the RC
algorithm they are using (might be using an HW RC algo).
The API returns a value expressed in Kbps.
Also, add the new get_expected_throughput() member
to the rate_control_ops structure in order to be
able to query the RC algorithm (this patch provides an
implementation of this API for both minstrel and
minstrel_ht).
The related member in the station_info object is now
filled accordingly when dumping a station.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to initialize the fallback device to have a correct mtu
set on this device. Otherwise the mtu is set to null and the device
is unusable.
Fixes: fd58156e45 ("IPIP: Use ip-tunneling code.")
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/nftables fixes for net
The following patchset contains nftables fixes for your net tree, they
are:
1) Fix crash when using the goto action in a rule by making sure that
we always fall back on the base chain. Otherwise, this may try to
access the counter memory area of non-base chains, which does not
exists.
2) Fix several aspects of the rule tracing that are currently broken:
* Reset rule number counter after goto/jump action, otherwise the
tracing reports a bogus rule number.
* Fix tracing of the goto action.
* Fix bogus rule number counter after goto.
* Fix missing return trace after finishing the walk through the
non-base chain.
* Fix missing trace when matching non-terminal rule.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that smp_confirm() is called "inline" we can have it return a
response code and have the sending of it be done in the shared place for
command handlers. One exception is when we're entering smp.c from mgmt.c
when user space responds to authentication, in which case we still need
our own code to call smp_failure().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since we're now calling smp_random() "inline" we can have it directly
return a response code and have the shared command handler send the
response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's no reason to have "smp" in this variable name since it is
already part of the SMP struct which provides sufficient context.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the SMP code was initially created (mid-2011) parts of the
Bluetooth subsystem were still not converted to use workqueues. This
meant that the crypto calls, which could sleep, couldn't be called
directly. Because of this the "confirm" and "random" work structs were
introduced.
These days the entire Bluetooth subsystem runs through workqueues which
makes these structs unnecessary. This patch removes them and converts
the calls to queue them to use direct function calls instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is no reason to have the initial local value conditional to
whether the remote value has bonding set or not. We can either way start
off with the value we received.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are no users of the smp_chan struct outside of smp.c so move it
away from smp.h. The addition of the l2cap.h include to hci_core.c,
hci_conn.c and mgmt.c is something that should have been there already
previously to avoid warnings of undeclared struct l2cap_conn, but the
compiler warning was apparently shadowed away by the mention of
l2cap_conn in the struct smp_chan definition.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Users may need information about the expected throughput
towards a given peer.
This value is supposed to consider the size overhead
generated by the 802.11 header.
This value is exported in kbps through the get_station() API
by including it into the station_info object.
Moreover, it is sent to user space when replying to the
nl80211 GET_STATION command.
This information will be useful to the batman-adv module
which will use it for its new metric computation.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
So that anyone listening on SOCKPROTO_RAW for raw frames will get all
NCI frames, in both directions. This actually implements userspace NFC
NCI sniffing.
It's now up to userspace to decode those frames.
Signed-off-by: Hiren Tandel <hirent@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This allows for a more generic NFC sniffing by using SOCKPROTO_RAW
SOCK_RAW to read RAW NFC frames. This is for sniffing anything but LLCP
(HCI, NCI, etc...).
Signed-off-by: Hiren Tandel <hirent@marvell.com>
Signed-off-by: Rahul Tank <rahult@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ATR_RES response received within Activation Parameters is already
in correct order. Reversing it fails LLCP magic number check and
so P2P functionality fails.
Signed-off-by: Hiren Tandel <hirent@marvell.com>
Signed-off-by: Rahul Tank <rahult@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
According to section 5.15.1.3 of the NFC Activity
Specification, multiple SENSF_REQ commands can be
received by a target before it receives an ATR_REQ
command. To handle this, add a routine that checks
whether a SENSF_REQ or ATR_REQ has been recieved.
If its a SENSF_REQ, respond appropriately and
continue waiting for a ATR_REQ. If its an ATR_REQ,
handle it as before.
CC: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The check in digital_tg_send_sensf_res() that excludes
the 'RD' field from the SENSF_RES is inverted. The 'RD'
field should be excluded when the SENSF_REQ 'RC' field
is equal to DIGITAL_SENSF_REQ_RC_NONE instead of when
its not equal. This is described in section 6.6.2.11
of the NFC Digital Specification.
CC: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This requires changing the nl80211 parsing code a bit to use
intermediate pointers for the allocation, but clarifies the
API towards the drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This also propagates through the drivers.
The orinoco driver uses the cfg80211 API structs for internal
bookkeeping, and so needs a (void *) cast that removes the
const - but that's OK because it allocates those pointers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Antonio and I were looking over this code and some things
didn't immediately make sense, so we came up with two small
clarifications.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that all objects are released in the reverse order via the
transaction infrastructure, we can enqueue the release via
call_rcu to save one synchronize_rcu. For small rule-sets loaded
via nft -f, it now takes around 50ms less here.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of caching the original skbuff that contains the netlink
messages, this stores the netlink message sequence number, the
netlink portID and the report flag. This helps to prepare the
introduction of the object release via call_rcu.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Now that all these function are called from the commit path, we can
pass the context structure to reduce the amount of parameters in all
of the nf_tables_*_notify functions. This patch also removes unneeded
branches to check for skb, nlh and net that should be always set in
the context structure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Leave the set content in consistent state if we fail to load the
batch. Use the new generic transaction infrastructure to achieve
this.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch speeds up rule-set updates and it also provides a way
to revert updates and leave things in consistent state in case that
the batch needs to be aborted.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch speeds up rule-set updates and it also introduces a way to
revert chain updates if the batch is aborted. The idea is to store the
changes in the transaction to apply that in the commit step.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch reworks the nf_tables API so set updates are included in
the same batch that contains rule updates. This speeds up rule-set
updates since we skip a dialog of four messages between kernel and
user-space (two on each direction), from:
1) create the set and send netlink message to the kernel
2) process the response from the kernel that contains the allocated name.
3) add the set elements and send netlink message to the kernel.
4) process the response from the kernel (to check for errors).
To:
1) add the set to the batch.
2) add the set elements to the batch.
3) add the rule that points to the set.
4) send batch to the kernel.
This also introduces an internal set ID (NFTA_SET_ID) that is unique
in the batch so set elements and rules can refer to new sets.
Backward compatibility has been only retained in userspace, this
means that new nft versions can talk to the kernel both in the new
and the old fashion.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The patch adds message type to the transaction to simplify the
commit the and abort routines. Yet another step forward in the
generalisation of the transaction infrastructure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Move the commit and abort routines to the bottom of the source code
file. This change is required by the follow up patches that add the
set, chain and table transaction support.
This patch is just a cleanup to access several functions without
having to declare their prototypes.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch generalises the existing rule transaction infrastructure
so it can be used to handle set, table and chain object transactions
as well. The transaction provides a data area that stores private
information depending on the transaction type.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The new transaction infrastructure updates the family, table and chain
objects in the context structure, so let's deconstify them. While at it,
move the context structure initialization routine to the top of the
source file as it will be also used from the table and chain routines.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In contrast to the direct access to the single SFF frame filters (which are
indexed by the SFF CAN ID itself) the single EFF frame filters are arranged
in a single linked hlist. To reduce the hlist traversal in the case of many
filter subscriptions a hash based access is introduced for single EFF filters.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The can_rcvlist_sff_proc_show_one() function which prints the array of filters
for the single SFF CAN identifiers is prepared to be used by a second caller.
Therefore it is also renamed to properly describe its future functionality.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
To be future-proof and for better readability the time comparisons are modified
to use time_after() instead of raw math.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This would be a no-op, so there is no reason to request it.
This also allows conversion of the current implementations of
ethtool_ops::{get,set}_rxfh_indir to ethtool_ops::{get,set}_rxfh
with no change other than their parameters.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We usually allocate special values of u32 fields starting from the top
down, so also change the value to 0xffffffff. As these operations
haven't been included in a stable release yet, it's not too late to
change.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We must return -EFAULT immediately rather than continuing into
the loop.
Similarly, we may as well return -EINVAL directly.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
fix build when BRIDGE_VLAN_FILTERING is not set
Fixes: 2796d0c648 ("bridge: Automatically manage port promiscuous mode")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're not taking a reference in the case where _gss_mech_get_by_pseudoflavor
loops without finding the correct rpcsec_gss flavour, so why are we
releasing it?
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Reported by checkpatch with the following warning:
"WARNING: macros should not use a trailing semicolon"
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Reported by checkpatch with the following message:
"WARNING: Missing a blank line after declarations"
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Prior to commit fbd929f2dc
bonding: support QinQ for bond arp interval
the arp monitoring code allowed for proper detection of devices
stacked on top of vlans. Since the above commit, the
code can still detect a device stacked on top of single
vlan, but not a device stacked on top of Q-in-Q configuration.
The search will only set the inner vlan tag if the route
device is the vlan device. However, this is not always the
case, as it is possible to extend the stacked configuration.
With this patch it is possible to provision devices on
top Q-in-Q vlan configuration that should be used as
a source of ARP monitoring information.
For example:
ip link add link bond0 vlan10 type vlan proto 802.1q id 10
ip link add link vlan10 vlan100 type vlan proto 802.1q id 100
ip link add link vlan100 type macvlan
Note: This patch limites the number of stacked VLANs to 2,
just like before. The original, however had another issue
in that if we had more then 2 levels of VLANs, we would end
up generating incorrectly tagged traffic. This is no longer
possible.
Fixes: fbd929f2dc (bonding: support QinQ for bond arp interval)
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@redhat.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: Patric McHardy <kaber@trash.net>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit dc8eaaa006.
vlan: Fix lockdep warning when vlan dev handle notification
Instead we use the new new API to find the lock subclass of
our vlan device. This way we can support configurations where
vlans are interspersed with other devices:
bond -> vlan -> macvlan -> vlan
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple devices in the kernel can be stacked/nested and they
need to know their nesting level for the purposes of lockdep.
This patch provides a generic function that determines a nesting
level of a particular device by its type (ex: vlan, macvlan, etc).
We only care about nesting of the same type of devices.
For example:
eth0 <- vlan0.10 <- macvlan0 <- vlan1.20
The nesting level of vlan1.20 would be 1, since there is another vlan
in the stack under it.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from linux-3.13, GRO attempts to build full size skbs.
Problem is the commit assumed one particular field in skb->cb[]
was clean, but it is not the case on some stacked devices.
Timo reported a crash in case traffic is decrypted before
reaching a GRE device.
Fix this by initializing NAPI_GRO_CB(skb)->last at the right place,
this also removes one conditional.
Thanks a lot to Timo for providing full reports and bisecting this.
Fixes: 8a29111c7c ("net: gro: allow to build full sized skb")
Bisected-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 802.15.4-2011 standard states that for each key, a list of devices
that use this key shall be kept. Previous patches have only considered
two options:
* a device "uses" (or may use) all keys, rendering the list useless
* a device is restricted to a certain set of keys
Another option would be that a device *may* use all keys, but need not
do so, and we are interested in the actual set of keys the device uses.
Recording keys used by any given device may have a noticable performance
impact and might not be needed as often. The common case, in which a
device will not switch keys too often, should still perform well.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds user-visible interfaces for the llsec infrastructure.
For the added methods, the only major difference between all add/remove
implementation lies in how the specific object is parsed, and for dump
requests, how objects are written into netlink messages.
To save on boilerplate code, table dumps are routed through a helper
function that handles netlink dump state, leaving the actual dumping
code to care only about iterating over the table to be dumped and
filling netlink messages. For add/remove methods, the boilerplate
required to work is not quite as large, but still enough to also move
into a local helper.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow datagram sockets to override the security settings of the device
they send from on a per-socket basis. Requires CAP_NET_ADMIN or
CAP_NET_RAW, since raw sockets can send arbitrary packets anyway.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds containers and mutators for the major ieee802154_llsec
structures to mac802154. Most of the (rather simple) ieee802154_llsec
structs are wrapped only to provide an rcu_head for orderly disposal,
but some structs - llsec keys notably - require more complex
bookkeeping.
Since each llsec key may be referenced by a number of llsec key table
entries (with differing key ids, but the same actual key), we want to
save memory and not allocate crypto transforms for each entry in the
table. Thus, the mac802154 llsec key is reference-counted instead.
Further, each key will have four associated crypto transforms - three
CCM transforms for the authsizes 4/8/16 and one CTR transform for
unauthenticated encryption. If we had a CCM* transform that allowed
authsize 0, and authsize as part of requests instead of transforms, this
would not be necessary.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link-layer security requires AES CCM for authenticated modes and AES CTR
for the unauthenticated encryption mode.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross says:
====================
A set of OVS changes for net-next/3.16.
The major change here is a switch from per-CPU to per-NUMA flow
statistics. This improves scalability by reducing kernel overhead
in flow setup and maintenance.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There exist configurations where the administrator or another management
entity has the foreknowledge of all the mac addresses of end systems
that are being bridged together.
In these environments, the administrator can statically configure known
addresses in the bridge FDB and disable flooding and learning on ports.
This makes it possible to turn off promiscuous mode on the interfaces
connected to the bridge.
Here is why disabling flooding and learning allows us to control
promiscuity:
Consider port X. All traffic coming into this port from outside the
bridge (ingress) will be either forwarded through other ports of the
bridge (egress) or dropped. Forwarding (egress) is defined by FDB
entries and by flooding in the event that no FDB entry exists.
In the event that flooding is disabled, only FDB entries define
the egress. Once learning is disabled, only static FDB entries
provided by a management entity define the egress. If we provide
information from these static FDBs to the ingress port X, then we'll
be able to accept all traffic that can be successfully forwarded and
drop all the other traffic sooner without spending CPU cycles to
process it.
Another way to define the above is as following equations:
ingress = egress + drop
expanding egress
ingress = static FDB + learned FDB + flooding + drop
disabling flooding and learning we a left with
ingress = static FDB + drop
By adding addresses from the static FDB entries to the MAC address
filter of an ingress port X, we fully define what the bridge can
process without dropping and can thus turn off promiscuous mode,
thus dropping packets sooner.
There have been suggestions that we may want to allow learning
and update the filters with learned addresses as well. This
would require mac-level authentication similar to 802.1x to
prevent attacks against the hw filters as they are limited
resource.
Additionally, if the user places the bridge device in promiscuous mode,
all ports are placed in promiscuous mode regardless of the changes
to flooding and learning.
Since the above functionality depends on full static configuration,
we have also require that vlan filtering be enabled to take
advantage of this. The reason is that the bridge has to be
able to receive and process VLAN-tagged frames and the there
are only 2 ways to accomplish this right now: promiscuous mode
or vlan filtering.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a static fdb entry is created, add the mac address
from this fdb entry to any ports that are currently running
in non-promiscuous mode. These ports need this data so that
they can receive traffic destined to these addresses.
By default ports start in promiscuous mode, so this feature
is disabled.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a BR_PROMISC per-port flag that will help us track if the
current port is supposed to be in promiscuous mode or not. For now,
always start in promiscuous mode.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code that allows static fdb entires to be synced to the
hw list for a specified port. This will be used later to
program ports that can function in non-promiscuous mode.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, ports on the bridge are capable of automatic
discovery of nodes located behind the port. This is accomplished
via flooding of unknown traffic (BR_FLOOD) and learning the
mac addresses from these packets (BR_LEARNING).
If the above functionality is disabled by turning off these
flags, the port requires static configuration in the form
of static FDB entries to function properly.
This patch adds functionality to keep track of all ports
capable of automatic discovery. This will later be used
to control promiscuity settings.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turn the flag change macro into a function to allow
easier updates and to reduce space.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The connected check fails to check for ip_gre nbma mode tunnels
properly. ip_gre creates temporary tnl_params with daddr specified
to pass-in the actual target on per-packet basis from neighbor
layer. Detect these tunnels by inspecting the actual tunnel
configuration.
Minimal test case:
ip route add 192.168.1.1/32 via 10.0.0.1
ip route add 192.168.1.2/32 via 10.0.0.2
ip tunnel add nbma0 mode gre key 1 tos c0
ip addr add 172.17.0.0/16 dev nbma0
ip link set nbma0 up
ip neigh add 172.17.0.1 lladdr 192.168.1.1 dev nbma0
ip neigh add 172.17.0.2 lladdr 192.168.1.2 dev nbma0
ping 172.17.0.1
ping 172.17.0.2
The second ping should be going to 192.168.1.2 and head 10.0.0.2;
but cached gre tunnel level route is used and it's actually going
to 192.168.1.1 via 10.0.0.1.
The lladdr's need to go to separate dst for the bug to trigger.
Test case uses separate route entries, but this can also happen
when the route entry is same: if there is a nexthop exception or
the GRE tunnel is IPsec'ed in which case the dst points to xfrm
bundle unique to the gre lladdr.
Fixes: 7d442fab0a ("ipv4: Cache dst in tunnels")
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Cc: Tom Herbert <therbert@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using command "ip tunnel add" to add a tunnel, the tunnel will be added twice,
through ip_tunnel_create() and ip_tunnel_update().
Because the second is unnecessary, so we can just break after adding tunnel
through ip_tunnel_create().
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding more than one chip on device-tree currently causes the probing
routine to always use the first chips data pointer.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, "ip -6 route get mark xyz" ignores the mark passed in
by userspace. Make it honour the mark, just like IPv4 does.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces rcu_assign_pointer(x, NULL) with RCU_INIT_POINTER(x, NULL)
The rcu_assign_pointer() ensures that the initialization of a structure
is carried out before storing a pointer to that structure.
And in the case of the NULL pointer, there is no structure to initialize.
So, rcu_assign_pointer(p, NULL) can be safely converted to RCU_INIT_POINTER(p, NULL)
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
We already extract the TCP flags for the key, might as well use that
for stats.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
The 'output' argument of the ovs_nla_put_flow() is the one from which
the bits are written to the netlink attributes. For SCTP we
accidentally used the bits from the 'swkey' instead. This caused the
mask attributes to include the bits from the actual flow key instead
of the mask.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Keep kernel flow stats for each NUMA node rather than each (logical)
CPU. This avoids using the per-CPU allocator and removes most of the
kernel-side OVS locking overhead otherwise on the top of perf reports
and allows OVS to scale better with higher number of threads.
With 9 handlers and 4 revalidators netperf TCP_CRR test flow setup
rate doubles on a server with two hyper-threaded physical CPUs (16
logical cores each) compared to the current OVS master. Tested with
non-trivial flow table with a TCP port match rule forcing all new
connections with unique port numbers to OVS userspace. The IP
addresses are still wildcarded, so the kernel flows are not considered
as exact match 5-tuple flows. This type of flows can be expected to
appear in large numbers as the result of more effective wildcarding
made possible by improvements in OVS userspace flow classifier.
Perf results for this test (master):
Events: 305K cycles
+ 8.43% ovs-vswitchd [kernel.kallsyms] [k] mutex_spin_on_owner
+ 5.64% ovs-vswitchd [kernel.kallsyms] [k] __ticket_spin_lock
+ 4.75% ovs-vswitchd ovs-vswitchd [.] find_match_wc
+ 3.32% ovs-vswitchd libpthread-2.15.so [.] pthread_mutex_lock
+ 2.61% ovs-vswitchd [kernel.kallsyms] [k] pcpu_alloc_area
+ 2.19% ovs-vswitchd ovs-vswitchd [.] flow_hash_in_minimask_range
+ 2.03% swapper [kernel.kallsyms] [k] intel_idle
+ 1.84% ovs-vswitchd libpthread-2.15.so [.] pthread_mutex_unlock
+ 1.64% ovs-vswitchd ovs-vswitchd [.] classifier_lookup
+ 1.58% ovs-vswitchd libc-2.15.so [.] 0x7f4e6
+ 1.07% ovs-vswitchd [kernel.kallsyms] [k] memset
+ 1.03% netperf [kernel.kallsyms] [k] __ticket_spin_lock
+ 0.92% swapper [kernel.kallsyms] [k] __ticket_spin_lock
...
And after this patch:
Events: 356K cycles
+ 6.85% ovs-vswitchd ovs-vswitchd [.] find_match_wc
+ 4.63% ovs-vswitchd libpthread-2.15.so [.] pthread_mutex_lock
+ 3.06% ovs-vswitchd [kernel.kallsyms] [k] __ticket_spin_lock
+ 2.81% ovs-vswitchd ovs-vswitchd [.] flow_hash_in_minimask_range
+ 2.51% ovs-vswitchd libpthread-2.15.so [.] pthread_mutex_unlock
+ 2.27% ovs-vswitchd ovs-vswitchd [.] classifier_lookup
+ 1.84% ovs-vswitchd libc-2.15.so [.] 0x15d30f
+ 1.74% ovs-vswitchd [kernel.kallsyms] [k] mutex_spin_on_owner
+ 1.47% swapper [kernel.kallsyms] [k] intel_idle
+ 1.34% ovs-vswitchd ovs-vswitchd [.] flow_hash_in_minimask
+ 1.33% ovs-vswitchd ovs-vswitchd [.] rule_actions_unref
+ 1.16% ovs-vswitchd ovs-vswitchd [.] hindex_node_with_hash
+ 1.16% ovs-vswitchd ovs-vswitchd [.] do_xlate_actions
+ 1.09% ovs-vswitchd ovs-vswitchd [.] ofproto_rule_ref
+ 1.01% netperf [kernel.kallsyms] [k] __ticket_spin_lock
...
There is a small increase in kernel spinlock overhead due to the same
spinlock being shared between multiple cores of the same physical CPU,
but that is barely visible in the netperf TCP_CRR test performance
(maybe ~1% performance drop, hard to tell exactly due to variance in
the test results), when testing for kernel module throughput (with no
userspace activity, handful of kernel flows).
On flow setup, a single stats instance is allocated (for the NUMA node
0). As CPUs from multiple NUMA nodes start updating stats, new
NUMA-node specific stats instances are allocated. This allocation on
the packet processing code path is made to never block or look for
emergency memory pools, minimizing the allocation latency. If the
allocation fails, the existing preallocated stats instance is used.
Also, if only CPUs from one NUMA-node are updating the preallocated
stats instance, no additional stats instances are allocated. This
eliminates the need to pre-allocate stats instances that will not be
used, also relieving the stats reader from the burden of reading stats
that are never used.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
The 5-tuple optimization becomes unnecessary with a later per-NUMA
node stats patch. Remove it first to make the changes easier to
grasp.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Add "openvswitch: " prefix to OVS_NLERR output
to match the other OVS_NLERR output of datapath.c
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Each use of pr_<level>_once has a per-site flag.
Some of the OVS_NLERR messages look as if seeing them
multiple times could be useful, so use net_ratelimit()
instead of pr_info_once.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
This is necessary, since u64 is not unsigned long long
in all architectures: u64 could be also uint64_t.
Signed-off-by: Daniele Di Proietto <daniele.di.proietto@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
This function must cast a const value to a non const value.
By adding an uintptr_t cast the warning is suppressed.
To avoid the cast (proper solution) several function signatures
must be changed.
Signed-off-by: Daniele Di Proietto <daniele.di.proietto@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
This change, firstly, avoids declaring the formal parameter const,
since it is treated as non const. (to avoid -Wcast-qual)
Secondly, it cast the pointer from void* to u8*, since it is used
in arithmetic (to avoid -Wpointer-arith)
Signed-off-by: Daniele Di Proietto <daniele.di.proietto@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
In few functions, const formal parameters are assigned or cast to
non-const.
These changes suppress warnings if compiled with -Wcast-qual.
Signed-off-by: Daniele Di Proietto <daniele.di.proietto@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
- fix NULL dereference in batadv_orig_hardif_seq_print_text()
- fix reference counting imbalance when using fragmentation
- avoid access to orig_node objects after they have been free'd
- fix local TT check for outgoing arp requests in DAT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=+DKS
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Include changes:
- fix NULL dereference in batadv_orig_hardif_seq_print_text()
- fix reference counting imbalance when using fragmentation
- avoid access to orig_node objects after they have been free'd
- fix local TT check for outgoing arp requests in DAT
Using whole of allocated pages reduces requested skb->data size.
This is just a little more thriftily allocation.
netperf does not show difference with the current performance.
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-05-15
Please pull this batch of fixes for the 3.15 stream...
For the mac80211 bits, Johannes says:
"One fix is to get better VHT performance and the other fixes tracing
garbage or other potential issues with the interface name tracing."
And...
"This has a fix from Emmanuel for a problem I failed to fix - when
association is in progress then it needs to be cancelled while
suspending (I had fixed the same for authentication). Also included a
fix from myself for a userspace API problem that hit the iw tool and a
fix to the remain-on-channel framework."
For the iwlwifi bits, Emmanuel says:
"Alex fixes the scan by disabling the fragmented scan. David prevents
scan offload while associated, the firmware seems not to like it. I
fix a stupid bug I made in BT Coex, and fix a bad #ifdef clause in rate
scaling. Along with that there is a fix for a NULL pointer exception
that can happen if we load the driver and our ISR gets called because
the interrupt line is shared. The fix has been tested by the reporter."
And...
"We have here a fix from David Spinadel that makes a previous fix more
complete, and an off-by-one issue fixed by Eliad in the same area.
I fix the monitor that broke on the way."
Beyond that...
Daniel Kim's one-liner fixes a brcmfmac regression caused by a typo
in an earlier commit..
Rajkumar Manoharan fixes an ath9k oops reported by David Herrmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There may be padding on the ticket contained in the key payload, so just ensure
that the claimed token length is large enough, rather than exactly the right
size.
Signed-off-by: Nathaniel Wesley Filardo <nwf@cs.jhu.edu>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e2b149cc4b ("crush: add chooseleaf_vary_r tunable") added the
crush_map::chooseleaf_vary_r field but missed the decode part. This
lead to misdirected requests caused by incorrect raw crush mapping
sets.
Fixes: http://tracker.ceph.com/issues/8226
Reported-and-Tested-by: Dmitry Smirnov <onlyjob@member.fsf.org>
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
It has been reported that using ZFSonLinux on rbd will result in memory
corruption. The bug report can be found here:
https://github.com/zfsonlinux/spl/issues/241http://tracker.ceph.com/issues/7790
The reason is that ZFS will send pages with page_count 0 into rbd, which in
turns send them to tcp_sendpage. However, tcp_sendpage cannot deal with
page_count 0, as it will do get_page and put_page, and erroneously free the
page.
This type of issue has been noted before, and handled in iscsi, drbd,
etc. So, rbd should also handle this. This fix address this issue by fall back
to slower sendmsg when page_count 0 detected.
Cc: Sage Weil <sage@inktank.com>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: stable@vger.kernel.org
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Ilya Dryomov <ilya.dryomov@inktank.com>
cgroup in general is moving towards using cgroup_subsys_state as the
fundamental structural component and css_parent() was introduced to
convert from using cgroup->parent to css->parent. It was quite some
time ago and we're moving forward with making css more prominent.
This patch drops the trivial wrapper css_parent() and let the users
dereference css->parent. While at it, explicitly mark fields of css
which are public and immutable.
v2: New usage from device_cgroup.c converted.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Johannes Weiner <hannes@cmpxchg.org>
conn_info_age value is calculated in ms, so need to be converted to
jiffies.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for max_tx_power in Get Connection Information
request. Value is read only once for given connection and then always
returned in response as parameter.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support to store local maximum TX power level for
connection when reply for HCI_Read_Transmit_Power_Level is received.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
TX power for LE links is immutable thus we do not need to query for it
if already have value.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for Get Connection Information mgmt command
which can be used to query for information about connection, i.e. RSSI
and local TX power level.
In general values cached in hci_conn are returned as long as they are
considered valid, i.e. do not exceed age limit set in hdev. This limit
is calculated as random value between min/max values to avoid client
trying to guess when to poll for updated information.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds conn_info_min_age and conn_info_max_age parameters to
debugfs which determine lifetime of connection information. Actual
lifetime will be random value between min and max age.
Default values for min and max age are 1000ms and 3000ms respectively.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
RFC 4861 states in 7.2.5:
The IsRouter flag in the cache entry MUST be set based on the
Router flag in the received advertisement. In those cases
where the IsRouter flag changes from TRUE to FALSE as a result
of this update, the node MUST remove that router from the
Default Router List and update the Destination Cache entries
for all destinations using that neighbor as a router as
specified in Section 7.3.3. This is needed to detect when a
node that is used as a router stops forwarding packets due to
being configured as a host.
Currently, when dealing with NA Message which IsRouter flag changes from
TRUE to FALSE, the kernel only removes router from the Default Router List,
and don't update the Destination Cache entries.
Now in order to update those Destination Cache entries, i introduce
function rt6_clean_tohost().
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_vti.c
Steffen Klassert says:
====================
pull request (net): ipsec 2014-05-15
This pull request has a merge conflict in net/ipv4/ip_vti.c
between commit 8d89dcdf80 ("vti: don't allow to add the same
tunnel twice") and commit a32452366b ("vti4:Don't count header
length twice"). It can be solved like it is done in linux-next.
1) Fix a ipv6 xfrm output crash when a packet is rerouted
by netfilter to not use IPsec.
2) vti4 counts some header lengths twice leading to an incorrect
device mtu. Fix this by counting these headers only once.
3) We don't catch the case if an unsupported protocol is submitted
to the xfrm protocol handlers, this can lead to NULL pointer
dereferences. Fix this by adding the appropriate checks.
4) vti6 may unregister pernet ops twice on init errors.
Fix this by removing one of the calls to do it only once.
From Mathias Krause.
5) Set the vti tunnel mark before doing a lookup in the error
handlers. Otherwise we don't find the correct xfrm state.
====================
The conflict in ip_vti.c was simple, 'net' had a commit
removing a line from vti_tunnel_init() and this tree
being merged had a commit adding a line to the same
location.
Signed-off-by: David S. Miller <davem@davemloft.net>
Netdev_priv is an accessor function, and has no purpose if its result is
not used.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@ local idexpression x; @@
-x = netdev_priv(...);
... when != x
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
