* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci:
davinci: dm646x EVM: Specify reserved EDMA channel/slots
davinci: da8xx/omapl EVM: Specify reserved channels/slots
davinci: support for EDMA resource sharing
davinci: edma: provide ability to detect insufficient CC info data
davinci: da8xx: sparse cleanup: remove duplicate entries in irq priorities
davinci: DM365: fixed second serial port
Davinci: tnetv107x evm board initial support
Davinci: tnetv107x initial gpio support
Davinci: tnetv107x soc support
Davinci: tnetv107x decompresser uart definitions
Davinci: generalized debug macros
Not all the channels and slots available on the DM646x EVM
are used by the devices on the EVM. These resources can be
used by the DSP to speed up codec operations.
This patch reserves these channels for the DSP.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently the EDMA queue to be used by for servicing ASP through
internal RAM is fixed to EDMAQ_0 and that to service internal RAM
from external RAM is fixed to EDMAQ_1.
This may not be the desirable configuration on all platforms. For
example, on DM365, queue 0 has large fifo size and is more suitable
for video transfers. Having audio and video transfers on the same
queue may lead to starvation on audio side.
platform data as defined currently passes a queue number to the driver
but that remains unused inside the driver.
Fix this by defining one queue each for ASP and RAM transfers in the
platform data and using it inside the driver.
Since EDMAQ_0 maps to 0, thats the queue that will be used if
the asp queue number is not initialized. None of the platforms
currently utilize ping-pong transfers through internal RAM so that
functionality remains unchanged too.
This patch has been tested on DM644x and OMAP-L138 EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch implements the following:
- interrupt initialization uses ioremap() instead of passing a virtual address
via davinci_soc_info.
- machine definitions directly point to cp_intc_init() or davinci_irq_init()
- davinci_intc_type and davinci_intc_base now get initialized in controller
specific init functions instead of davinci_common_init()
- minor fix in davinci_irq_init() to use intc_irq_num instead of
DAVINCI_N_AINTC_IRQ
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The IDE platform device is registered in three different places (2 board files
for DM644x and in dm646x.c for DM646x) while both the IDE base address and the
IDE IRQ are the same for both SoCs -- therefore, the proper place for the IDE
platform seems to be in devices.c. Merge the IDE platform data and registration
code and create davinci_init_ide() in place of dm646x_init_ide()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently each DaVinci board file #define's its own version of the EMIFA base
addresses (all named DAVINCI_ASYNC_EMIF_*_BASE), which leads to duplication.
Move these #define's to the SoC specific headers, changing their prefixes from
'DAVINCI' to the 'DM355', 'DM644X', and 'DM646X' since all these base addresses
are SoC specific...
And while at it, rename DM646X_ASYNC_EMIF_DATA_CE0_BASE to
DM646X_ASYNC_EMIF_CS2_SPACE_BASE in order to match the DM646x datasheet.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Remove unneeded 'struct davinci_clk' wrapper around 'struct
clk_lookup' and use clk_lookup directly.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds the CDCE949 reference oscillator to
the davinci clock list.
On the DM6467T EVM, the CDCE949 is responsible for
generating the pixel clock for display. On the DM6467
EVM, this pixel clock was being obtained from an
internal source. This is not possible on the DM6467T
EVM because of the presence of a 33MHz oscillator.
The TSIF module also requires the CDCE949 to generate
the data clocks.
The actual clock definitions will be added by patches
adding support for DM6467T VPIF and TSIF. This patch
mearly lays the foundation for that work.
Signed-off-by: Nageswari Srinivasan <nageswari@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM6467T (T for Turbo) is a newer and faster DM6467
part from TI. The new part supports 1080p video and
has the ARM running at 495MHz. More SoC information:
http://focus.ti.com/docs/prod/folders/print/tms320dm6467t.html
Spectrum Digital, Inc has a new EVM for this part.
It is _mostly_ same as the older DM6467 EVM except
for a 33MHz crystal input and THS8200 video encoder
for 1080p support.
The meat of this patch is dedicated to initializing
the crystal frequency from EVM board file.
Additional notes:
I did consider some alternative ways to make the crystal
input board specific including - (1) having board code
initialize the crystal frequency using the first member
of soc_info->cpu_clks array (2) introducing a new ref_clk_rate
member in soc_info structure.
But, the current way seems to be the simplest and least
intruding considering that both the clock array and SoC
info structure are actually private to the SoC file. Also
the fact that davinci_common_init() initializes both the
soc_info and clocks in one go.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently all the #defines and static variables in the
board-dm646x-evm.c file are located right at the start
of the file because of which the related code is not
together - making reading the code difficult.
This patch moves around the code keeping related code
together.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
A section mismatch is reported for gpio_led_platform_data
as it is referenced by a non annotated function (evm_led_setup)
This patch fixes the issue by converting the __initconst to const
as is the case in arch/arm/mach-davinci/board-dm644x-evm.c file.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform data and partition info for NAND on dm6467 EVM.
Note that the partition layout is dependent on the UBL, U-Boot etc. used. This
patch tries to minimize that dependency by setting first partition for UBL,
U-Boot and environment altogether.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There have accumulated quite a lot of them after the code reorganizations...
In several cases I had to replace #include <linux/dma-mapping.h> which wasn't
needed directly but happened to #include <linux/err.h> which was needed.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
VPIF display changes (Chaithrika)
Add platform device and resource structures. Also define a platform specific
clock setup function that can be accessed by the driver to configure the clock
and CPLD.
VPIF caputure changes (Murali)
1) Modify vpif_subdev_info to add board_info, routing information and
vpif interface configuration. Remove addr since it is part of
board_info
2) Add code to setup channel mode and input decoder path for vpif
capture driver
Also incorporated comments against version v0 of the patch series and
added a spinlock to protect writes to common registers
Tested on DM6467 on channel 0 using TVP514x. Following bootargs used
for drivers:
vpif_capture.ch0_bufsize=829440 vpif_display.ch2_bufsize=829440
Signed-off-by: Manjunath Hadli <mrh@ti.com>
Signed-off-by: Brijesh Jadav <brijesh.j@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested on DM6446, DM355, DM6447, DA850 EVMs.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There is no need to pass clock name strings in platform_data.
Instead, setup clkdev nodes to have correct ASoC device names.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Controls ATA_RSTn and ATA_PWD through CPLD register 0 to enable ATA. An I2C
driver is added for the same. Calls ide init if enabled in configuration.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
1) Registers the platform devices for ASP on dm355, dm644x and dm646x
so that the machine driver can probe to get ASP related platform
data.
2) Move towards definition of the asp clocks using physical name(for
dm355 and dm644x)
3) Add platform data to board specific files.
Signed-off-by: Naresh Medisetty <naresh@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm646x-evm.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Factor out the code to extract that mac address from
i2c eeprom.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The dm644x and dm646x board files have i2c eeprom read and
write routines but they are not used so remove them.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Since most of the emac platform_data is really SoC specific
and not board specific, move it to the SoC-specific files.
Put a pointer to the platform_data in the soc_info structure
so the board-specific code can set some of the platform_data
if it needs to.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Create a structure to encapsulate SoC-specific information.
This will assist in generalizing code so it can be used by
different SoCs that have similar hardware but with minor
differences such as having a different base address.
The idea is that the code for each SoC fills out a structure
with the correct information. The board-specific code then
calls the SoC init routine which in turn will call a common
init routine that makes a copy of the structure, maps in I/O
regions, etc.
After initialization, code can get a pointer to the structure
by calling davinci_get_soc_info(). Eventually, the common
init routine will make a copy of all of the data pointed to
by the structure so the original data can be made __init_data.
That way the data for SoC's that aren't being used won't consume
memory for the entire life of the kernel.
The structure will be extended in subsequent patches but
initially, it holds the map_desc structure for any I/O
regions the SoC/board wants statically mapped.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add support for DM646x SoC (a.k.a DaVinci HD) and its Evalution
Module (EVM.)
Original support done by Sudhakar Rajashekhara.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
