This patch does following:
- Clean up NVRAM code.
- Optimizes reading of primary/secondary flash image validation.
- Remove 0xff mask and make correct width in FLT structure.
- Use endian macros to assign static fields in fwdump header.
- Correct fdwt checksum calculation.
- Simplify ql_dump_buffer() interface usage.
- Add endianizers to 27xx firmware image validator.
- fixes compiler warnings for big endian architecture.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes reported speed for min_link and max_supported speed. Also
rename sysfs nodes link_speed and max_supported to be consistent with
{min|max}_suuported_speed.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Mike Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds PCI device ID ISP28XX for Gen7 support. Also signature
determination for primary/secondary flash image for ISP27XX/28XX is aded as
part of Gen7 support.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes regression introduced for the N2N support for FC-NVMe. For
FC-NVMe with N2N connection, instead of FW initiating the Login, Driver
starts Login process. This patch migrates that new process from a
standalone path into existing session management state machine. With this
state change now driver will not wait for pull NPort ID from FW.
Fixes: edd05de197 ("scsi: qla2xxx: Changes to support N2N logins")
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When connection type is N_Port to N_Port (point-to-point), there
is a possibilty where initiator will not send PLOGI request and
will directly send PRLI. In N2N connection the port has higher
port name sends the PLOGI but not allow to send PRLI if is a
target mode. Only initiator is allowed to send PRLI.
Current driver code deletes old session when it receives PLOGI
request. If we will not receive PLOGI request then we will not
delete old session and create new session. Add check for N2N
with PRLI receive only and trigger cleanup. For this case, the
cleanup requires individual cmd abort instead of using implicit
logout as a broad stroke flush.
Signed-off-by: Krishna Kant <krishna.kant@purestorage.com>
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we discovered a topology that is N2N then we will issue a login to
the target. If our WWPN is bigger than the target's WWPN then we will
initiate login, otherwise we will just wait for the target to initiate
login.
[mkp: many whitespace errors]
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds logic to handle the completion of FC-NVMe commands and
creates a sub-command in the SRB command structure to manage NVMe
commands.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added logic to change the login process into an optional PRIL step for
FC-NVMe ports as a separate operation, such that we can change type to
0x28 (NVMe).
Currently, the driver performs the PLOGI/PRLI together as one operation,
but if the discovered port is an NVMe port then we first issue the PLOGI
and then we issue the PRLI. Also, the fabric discovery logic was changed
to mark each discovered FC NVMe port, so that we can register them with
the FC-NVMe transport later.
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code blindly does State Change Registration when
the link is up. Move SCR behind fabric scan, so that arbitrated
loop scan would not get erroneous error message.
Some of the other improvements are as follows
- Add session deletion for TPRLO and send acknowledgment for TPRLO.
- Enable FW option to move ABTS, RIDA & PUREX from RSPQ to ATIOQ.
- Save NPort ID early in link init.
- Move ABTS & RIDA to ATIOQ helps in keeping command ordering and
link up sequence ordering.
- Save Nport ID and update VP map so that SCSI CMD/ATIO won't be dropped.
- fcport alloc does the initializes memory to zero. Remove memset to
zero since It might corrupt link list.
- Turn off Registration for State Change MB in loop mode.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Currently code performs a full scan of the fabric for
every RSCN. Its an expensive process in a noisy large SAN.
This patch optimizes expensive fabric discovery process by
scanning switch for the affected port when RSCN is received.
Currently Initiator Mode code makes login/logout decision without
knowledge of target mode. This causes driver and firmware to go
out-of-sync. This framework synchronizes both initiator mode
personality and target mode personality in making login/logout
decision.
This patch adds following capabilities in the driver
- Send Notification Acknowledgement asynchronously.
- Update session/fcport state asynchronously.
- Create a session or fcport struct asynchronously.
- Send GNL asynchronously. The command will ask FW to
provide a list of FC Port entries FW knows about.
- Send GPDB asynchronously. The command will ask FW to
provide detail data of an FC Port FW knows about or
perform ADISC to verify the state of the session.
- Send GPNID asynchronously. The command will ask switch
to provide WWPN for provided NPort ID.
- Send GPSC asynchronously. The command will ask switch
to provide registered port speed for provided WWPN.
- Send GIDPN asynchronously. The command will ask the
switch to provide Nport ID for provided WWPN.
- In driver unload path, schedule all session for deletion
and wait for deletion to complete before allowing driver
unload to proceed.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
[ bvanassche: fixed spelling in patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fixes: 969a619 ("qla2xxx: Add support for buffer to buffer credit value for ISP27XX.")
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Parse the retry delay timer field from the FCP response data and if:
- It is not zero
- The SCSI status is busy or queue full
return SCSI_MLQUEUE_TARGET_BUSY for the number of milliseconds specified
in the retry delay timer field.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add support for the D-port (diagnostic port) fabric switch feature.
(Fabric Switch initiates loopback style port testing)
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add support for the FA-WWN (fabric assigned wwn) fabric switch feature.
(Fabric Assigned World Wide Port Name)
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For ISP27xx use the request/response queue index shadow registers
to avoid directly access them on the PCI bus.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Try to acquire the semaphore; if semaphore is hung then acquire it by force.
The ISP reset clears the semaphore, thereby implicitly releasing it.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Update the driver copyright from 2003-2011 to 2003-2012.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver needs to update protection bytes for uninitialized sectors as they are
not DMA-d.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Reviewed-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The firmware spec has the fcp_data_dseg_len defined as a 32-bit
value, while the corresponding field in the driver structure has
it defined as a 16-bit value.
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We now enable/disable "Additional Receive Credits" in f/w based on nvram
parameter "Extended_BB_Credits" bit (i.e. Enhanced-Features: at offset 0x196).
This is applicable only for GEN2 CNAs.
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
One byte added to make the IOCB structure satisfy
size requirements.
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ISP24xx and above must query the host-status register, not HCCR.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In case the onboard firmware is unable to be read or loaded for
operation, attempt to fallback to a limited-operational firmware
image stored in a different flash region. This will allow a user
to reflash and correct a board with proper operational firmware.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware currently provides PB and PGF TLVs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rather than assuming a particular layout of the data. Applies to
recent ISPs only.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
