This patch removes "buswidth" struct member, and sets the default buswidth
to the natively supported 10 bit. You can select 8 bit buswidth by new flag.
This patch also modify ap325rxa/migor setup.c
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add supports for the radio system on the Intel Russellville board.
It's a In-Vehicle Infotainment board with a radio tuner and DSP.
This umbrella driver has the DSP and tuner as V4L2 subdevs and calls them
when needed.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initial support for the SAA7706H Car Radio DSP.
It is a I2C device and currently the mute control is supported.
When the device is unmuted it is brought out of reset and initiated using
the proposed intialisation sequence.
When muted the DSP is brought into reset state.
[akpm@linux-foundation.org: include delay.h]
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: Douglas Schilling Landgraf <dougsland@gmail.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fix Video/Sound support "Leadtek winfast tv usbii deluxe".
Now, it is working Stereo, IR, Radio, TV, Svideo and Composite.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change attempts to fix the ivtv tinny audio problem by keeping digitizer
to encoder audio clocks running, while disabling the video clocks as needed to
avoid unpredictable PCI bus hangs.
To accomplish this, for the cx25840 module enabling of audio streaming had
to be separated from enabling video streaming, requiring an additional
v4l2_subdev_audio_op and calls to this new op in the pvrusb2 and ivtv drivers.
The cx231xx and cx23885 driver use the cx25840 module for affecting only
video on s_stream calls, so those drivers needed no change.
The CX23418 hardware does not exhibit either the tinny audio problem nor the PCI
bus hang, so the cx18 driver did not need corresponding changes.
CX2341[56] based cards that are not using the CX2584x family of chips
do not seem to be affected by the tinny audio problem, and this change should
not affect how they are configured. It will delay their first capture by
starting by another 300 msec though.
Many thanks go to Argus <pthorn-ivtvd@styx2002.no-ip.org> and
Martin Dauskardt <martin.dauskardt@gmx.de> whose persistent testing and
investigation of this problem will hopefully fix this problem once and for all
for many ivtv users.
Reported-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Reported-by: Argus <pthorn-ivtvd@styx2002.no-ip.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When preparing the linux-next patches, I got those errors:
include/media/ir-core.h:29: warning: left shift count >= width of type
In file included from include/media/ir-common.h:29,
from drivers/media/video/ir-kbd-i2c.c:50:
drivers/media/video/ir-kbd-i2c.c: In function ‘ir_probe’:
drivers/media/video/ir-kbd-i2c.c:324: warning: left shift count >= width of type
Unfortunately, enum is 32 bits on i386. As we define IR_TYPE_OTHER as 1<<63,
it won't work on non 64 bits arch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds an structure to ir_input_register to contain IR device characteristics,
like supported protocols and a callback to handle protocol event changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add sysfs skeleton to export remote controller information via
/sys/class/irrcv.
For now, the code doesn't do much. It just exports an attribute that
is meant to report and control the IR protocol used by the keytable.
However, the callbacks for this new attribute weren't set yet.
Also, it lacks symlinks to the used event interface.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It has been experimentally found out, that the sensor only supports up to
512x384 video output and also has some restrictions on minimum scale. We
disable non-working size ranges until, maybe, someone finds out how to properly
set them up. Also add cropping support, an auto white balance control, platform
data to specify master clock frequency and polarity of the IOCTL pin.
create mode 100644 include/media/rj54n1cb0c.h
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert soc-camera core and all soc-camera drivers to the new mediabus
API. This also takes soc-camera client drivers one step closer to also be
usable with generic v4l2-subdev host drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Video subdevices, like cameras, decoders, connect to video bridges over
specialised busses. Data is being transferred over these busses in various
formats, which only loosely correspond to fourcc codes, describing how video
data is stored in RAM. This is not a one-to-one correspondence, therefore we
cannot use fourcc codes to configure subdevice output data formats. This patch
adds codes for several such on-the-bus formats and an API, similar to the
familiar .s_fmt(), .g_fmt(), .try_fmt(), .enum_fmt() API for configuring those
codes. After all users of the old API in struct v4l2_subdev_video_ops are
converted, it will be removed. Also add helper routines to support generic
pass-through mode for the soc-camera framework.
create mode 100644 drivers/media/video/soc_mediabus.c
create mode 100644 include/media/soc_mediabus.h
create mode 100644 include/media/v4l2-mediabus.h
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After this change drivers can be further extended to not fail, if they don't
get platform data, but to use defaults.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Up to now, if a client driver needed platform data apart from those contained
in struct soc_camera_link, it had to embed the struct into its own object. This
makes the use of such a driver in configurations other than soc-camera
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce new v4l2-subdev sensor operations, move .enum_framesizes() and
.enum_frameintervals() methods to it, add a new .g_skip_top_lines() method
and switch soc-camera to use it instead of .y_skip_top soc_camera_device
member, which can now be removed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a helper function to get description of a digital
video preset added by the video timing API. This will be useful for drivers
implementing the above API.
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We'll need to register a sysfs class for the IR devices. As such, the better
is to have the input_register_device()/input_unregister_device() inside
the ir register/unregister functions.
Also, solves a naming problem with V4L ir_input_init() function, that were,
in fact, registering a device.
While here, do a few cleanups at budget-ci IR logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, ir_input_free does more than just freeing the keytab. Better to
rename it as ir_input_unregister.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move non-V4L specific stuff from ir-functions ir_input_init() into
a new function to register ir devices: ir_input_register().
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Split the ir-common into two separate modules:
- ir-core: it is the IR-independent functions;
- ir-common: has the common part used by V4L drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds the above APIs to the v4l2 core. This is based on version v1.2
of the RFC titled "V4L - Support for video timings at the input/output interface"
Following new ioctls are added:-
- VIDIOC_ENUM_DV_PRESETS
- VIDIOC_S_DV_PRESET
- VIDIOC_G_DV_PRESET
- VIDIOC_QUERY_DV_PRESET
- VIDIOC_S_DV_TIMINGS
- VIDIOC_G_DV_TIMINGS
Please refer to the RFC for the details. This code was tested using vpfe
capture driver on TI's DM365. Following is the test configuration used :-
Blu-Ray HD DVD source -> TVP7002 -> DM365 (VPFE) ->DDR
A draft version of the TVP7002 driver (currently being reviewed in the mailing
list) was used that supports V4L2_DV_1080I60 & V4L2_DV_720P60 presets.
A loopback video capture application was used for testing these APIs. This calls
following IOCTLS :-
- verify the new v4l2_input capabilities flag added
- Enumerate available presets using VIDIOC_ENUM_DV_PRESETS
- Set one of the supported preset using VIDIOC_S_DV_PRESET
- Get current preset using VIDIOC_G_DV_PRESET
- Detect current preset using VIDIOC_QUERY_DV_PRESET
- Using stub functions in tvp7002, verify VIDIOC_S_DV_TIMINGS
and VIDIOC_G_DV_TIMINGS ioctls are received at the sub device.
- Tested on 64bit platform by Hans Verkuil
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video_device::minor field is used where it shouldn't, either to
- test for error conditions that can't happen anymore with the current
v4l-dvb core,
- store the value in a driver private field that isn't used anymore,
- check the video device type where video_device::vfl_type should be
used, or
- create the name of a kernel thread that should get a stable name.
Remove or fix those use cases.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace the video_is_unregistered function by a video_is_registered
function. The V4L2_FL_UNREGISTERED flag is replaced by a
V4L2_FL_REGISTERED flag.
This change makes the video_is_registered function return coherent
results when called on an initialize but not yet registered video_device
instance. The function can now be used instead of checking
video_device::minor.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many drivers access the device number (video_device::v4l2_devnode::num)
in order to print the video device node name. Add and use a helper
function to retrieve the video_device node name.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This IR uses NEC protocol, with address=0x14. This keymap is similar
to the existing Terratec Cinergy XS, except that:
- it contains the full address/command code;
- the Music button were mapped as KEY_RADIO;
- some keycodes from the previous entry were wrong, IMHO.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The same loop to seek for a key were used on different places. Also,
no spinlock were protecting it to avoid the risk of replacing a keycode
while seeking for a new code.
This cleanup does:
- create an unique function to seek for a code;
- adds an spinlock to protect the table lookup;
- remove some unused code;
- simplifies to code to make it easier to understand.
Basically no change in behavior should be noticed after this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the IR table is initialized by calling ir_input_init(). However,
this function doesn't return any error code, nor has a function to be called
when de-initializing the IR's.
Change the return argment to integer and make sure that each driver will
handle the error code. Also adds a function to free any resources that may
be allocating there: ir_input_free().
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that V4L drivers can support more than 7 bits for scan code, let's
add a modified version for the Hauppauge Grey IR containing the full IR
scancode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the IR conversion to dynamic tables has finished, we can get
rid of some fields and definitions that aren't used anymore.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L drivers use an static keycode vector with 128 entries, where the scancode
indexes the keycode. While this works, it limits the scancodes to have only
7 bits, not allowing for example full RC5 codes.
Instead of implementing the same code on every V4L driver, provide a common
infrastructure to handle the bigger tables, minimizing the changes inside
each driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As newer IR common code will be added on other files, we need a global
debug var inside the module.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The I2C adapter ID is actually depends on Board and may vary, Davinci
uses id=1, but in case of AM3517 id=3.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For whatever reason, the device structure pointer to
videobuf_queue_vmalloc_init is typed "void *", even though it's passed
right through to videobuf_queue_core_init(), which expects a struct
device pointer. The other videobuf implementations use struct device *;
I think vmalloc should too.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The videobuf_queue_ops function vector is not declared constant, but
there's no need for the videobuf layer to ever change it. Make it const
so that videobuf users can make their operations const without warnings.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Upcoming I2C v4l2_subdev drivers need a way to control the subdevice
power state from the core. This use case is already partially covered by
the tuner s_standby operation, but no way to explicitly come back from
the standby state is available.
Rename the tuner s_standby operation to core s_power, and fix tuner
drivers accordingly. The tuner core will call s_power(0) instead of
s_standby(). No explicit call to s_power(1) is required for tuners as
they are supposed to wake up from standby automatically.
[mchehab@redhat.com: CodingStyle fix]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for TEF6862 Car Radio Enhanced Selectivity Tuner.
It's implemented as a subdev, supporting checking signal strength
and setting and getting frequency.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch brings infrared remote support for some cx88 based cards.
Such as TeVii S460,S420.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch brings infrared remote support for some cx88 based cards.
Such as:
TeVii S460,S420; Omicom SS4; SatTrade ST4200;
TBS 8920,8910; Prof 7300,6200.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
