Omit an extra message for a memory allocation failure in s5p_mfc_probe()
function. This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Trivial fix to spelling mistake in mfc_err error messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Further investigation revealed that codec buffers also don't need to
be allocated at higher addresses than firmware base for MFC v6+ hardware.
Those buffers can be quite large and its size depends on the selected
format and framesize. This patch changes the way the codec buffers are
allocated - driver will use generic allocator for them instead of the
pre-allocated buffer for firmware and contexts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Clock should be turned off after calling s5p_mfc_init_hw() from the
watchdog worker, like it is already done in the s5p_mfc_open() which also
calls this function.
Fixes: af93574678 ("[media] MFC: Add MFC 5.1 V4L2 driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Documentation for MFC hardware still uses 'left' and 'right' names for
the memory channel/banks, so replace BANK1/2 defines with more appropriate
BANK_L/R names.
Suggested-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It turned out that all versions of MFC v6+ hardware doesn't have a strict
requirement for ALL buffers to be allocated on higher addresses than the
firmware base like it was documented for MFC v5. This requirement is true
only for the device and per-context buffers. All video data buffers can be
allocated anywhere for all MFC v6+ versions. Basing on this fact, the
special DMA configuration based on two reserved memory regions is not
really needed for MFC v6+ devices, because the memory requirements for the
firmware, device and per-context buffers can be fulfilled by the simple
probe-time pre-allocated block allocator introduced in previous patch.
This patch enables support for such pre-allocated block based allocator
always for MFC v6+ devices. Due to the limitations of the memory management
subsystem the largest supported size of the pre-allocated buffer when no
CMA (Contiguous Memory Allocator) is enabled is 4 MiB.
This patch also removes the requirement to provide two reserved memory
regions for MFC v6+ devices in device tree. Now the driver is fully
functional without them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The main reason for using special configuration of IOMMU domain was the
problem with MFC firmware, which failed to operate properly when placed
at 0 DMA address. Instead of adding custom code for configuring each
variant of IOMMU domain and architecture specific glue code, simply use
what arch code provides and if the DMA base address equals zero, skip
first 128 KiB to keep required alignment. This patch also make the driver
operational on ARM64 architecture, because it no longer depends on ARM
specific DMA-mapping and IOMMU glue code functions.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Current MFC driver depends on the fact that when IOMMU is available, the
DMA-mapping framework and its IOMMU glue will use first-fit allocator.
This was true for ARM architecture, but its not for ARM64 arch. However, in
case of MFC v6+ hardware and latest firmware, it turned out that there is
no strict requirement for ALL buffers to be allocated on higher addresses
than the firmware base. This requirement is true only for the device and
per-context buffers. All video data buffers can be allocated anywhere for
all MFC v6+ versions.
Such relaxed requirements for the memory buffers can be easily fulfilled
by allocating firmware, device and per-context buffers from the probe-time
preallocated larger buffer. This patch adds support for it. This way the
driver finally works fine on ARM64 architecture. The size of the
preallocated buffer is 8 MiB, what is enough for three instances H264
decoders or encoders (other codecs have smaller memory requirements).
If one needs more for particular use case, one can use "mem" module
parameter to force larger (or smaller) buffer (for example by adding
"s5p_mfc.mem=16M" to kernel command line).
[mchehab@s-opensource.com: fix two checkpatch warnings: don't initialize
static to NULL; don't use S_foo permisions]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move code for DMA memory configuration with IOMMU into separate function
to make it easier to compare what is being done in each case.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Firmware for MFC v6+ variants is not larger than 400 KiB, so there is no
need to allocate a full 1 MiB buffer for it. Reduce it to 512 KiB to keep
proper alignment of allocated buffer.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Once firmware buffer has been converted to use s5p_mfc_priv_buf structure,
it is possible to allocate it with existing s5p_mfc_alloc_priv_buf()
function. This change will help to reduce code variants in the next
patches.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
To complete DMA memory configuration for MFC device, allocation of the
firmware buffer is needed, because some parameters are dependant on its base
address. Till now, this has been handled in the s5p_mfc_alloc_firmware()
function. This patch moves that logic to s5p_mfc_configure_dma_memory() to
keep DMA memory related operations in a single place. This way
s5p_mfc_alloc_firmware() is simplified and does what it name says. The
other consequence of this change is moving s5p_mfc_alloc_firmware() call
from the s5p_mfc_probe() function to the s5p_mfc_configure_dma_memory().
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use s5p_mfc_priv_buf structure for keeping the firmware image. This will
help handling of firmware buffer allocation in the next patches.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Setting DMA max segment size to 32 bit mask is a part of DMA memory
configuration, so move those calls to s5p_mfc_configure_dma_memory()
function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change parameters for s5p_mfc_alloc_priv_buf() and s5p_mfc_release_priv_buf()
functions. Instead of DMA device pointer and a base, provide common MFC
device structure and memory bank context identifier.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Internal MFC driver device structure contains two entries for keeping
addresses of the DMA memory banks. Replace them with the dma_base[] array
and use defines for accessing particular banks. This will help to simplify
code in the next patches.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Internal MFC driver device structure contains two pointers to devices used
for DMA memory allocation: mem_dev_l and mem_dev_r. Replace them with the
mem_dev[] array and use defines for accessing particular banks. This will
help to simplify code in the next patches.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unused structures, definitions and functions
that are no longer called from the driver code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Reviewed-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Interrupt routine must wake process waiting for given interrupt AFTER
updating driver's internal structures and contexts. Doing it in-between
is a serious bug. This patch moves all calls to the wake() function to
the end of the interrupt processing block to avoid potential and real
races, especially on multi-core platforms. This also fixes following issue
reported from clock core (clocks were disabled in interrupt after being
unprepared from the other place in the driver, the stack trace however
points to the different place than s5p_mfc driver because of the race):
WARNING: CPU: 1 PID: 18 at drivers/clk/clk.c:544 clk_core_unprepare+0xc8/0x108
Modules linked in:
CPU: 1 PID: 18 Comm: kworker/1:0 Not tainted 4.10.0-next-20170223-00070-g04e18bc99ab9-dirty #2154
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: pm pm_runtime_work
[<c010d8b0>] (unwind_backtrace) from [<c010a534>] (show_stack+0x10/0x14)
[<c010a534>] (show_stack) from [<c033292c>] (dump_stack+0x74/0x94)
[<c033292c>] (dump_stack) from [<c011cef4>] (__warn+0xd4/0x100)
[<c011cef4>] (__warn) from [<c011cf40>] (warn_slowpath_null+0x20/0x28)
[<c011cf40>] (warn_slowpath_null) from [<c0387a84>] (clk_core_unprepare+0xc8/0x108)
[<c0387a84>] (clk_core_unprepare) from [<c0389d84>] (clk_unprepare+0x24/0x2c)
[<c0389d84>] (clk_unprepare) from [<c03d4660>] (exynos_sysmmu_suspend+0x48/0x60)
[<c03d4660>] (exynos_sysmmu_suspend) from [<c042b9b0>] (pm_generic_runtime_suspend+0x2c/0x38)
[<c042b9b0>] (pm_generic_runtime_suspend) from [<c0437580>] (genpd_runtime_suspend+0x94/0x220)
[<c0437580>] (genpd_runtime_suspend) from [<c042e240>] (__rpm_callback+0x134/0x208)
[<c042e240>] (__rpm_callback) from [<c042e334>] (rpm_callback+0x20/0x80)
[<c042e334>] (rpm_callback) from [<c042d3b8>] (rpm_suspend+0xdc/0x458)
[<c042d3b8>] (rpm_suspend) from [<c042ea24>] (pm_runtime_work+0x80/0x90)
[<c042ea24>] (pm_runtime_work) from [<c01322c4>] (process_one_work+0x120/0x318)
[<c01322c4>] (process_one_work) from [<c0132520>] (worker_thread+0x2c/0x4ac)
[<c0132520>] (worker_thread) from [<c0137ab0>] (kthread+0xfc/0x134)
[<c0137ab0>] (kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
---[ end trace 1ead49a7bb83f0d8 ]---
Fixes: af93574678 ("[media] MFC: Add MFC 5.1 V4L2 driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: stable@vger.kernel.org # v4.5+
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix s5p_mfc_set_dec_frame_buffer_v6() to print buffer pointer in hex
to be consistent with the rest of the messages in the routine.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Initialize members of the internal device and context structures as early
as possible to avoid access to uninitialized objects on initialization
failures. If loading firmware or creating of the hardware instance fails,
driver will access device or context queue in error handling path, which
might not be initialized yet, what causes kernel panic. Fix this by moving
initialization of all static members as early as possible.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Exynos5433 SoC has MFC v8 hardware module, but it has more
complex clock hierarchy, so a new compatible is added.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch changes the code for handling clocks. Now clocks are defined
per each device variant, what is a preparation for adding support for
Exynos 5433 MFC V8, which has more clocks than all previous versions.
Also use devm_clk_get() to simplify cleanup path.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch moves preparation of clocks from s5p_mfc_init_pm()
(driver probe) to s5p_mfc_power_on() (start of device operation).
This change will allow to use runtime power usage optimization
on newer Samsung Exynos platforms (for example Exynos 5433).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
After commit "s5p-mfc: Fix clock management in s5p_mfc_release function"
all clocks related functions are called only when MFC device is really
available, so there is no additional check needed for NULL
gate clocks. This patch simplifies the code and kills IS_ERR_OR_NULL
macro usage.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CONFIG_PM is always enabled on Exynos platforms, so remove dead code
related to early development of MFC driver on platform without PM support.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move clock disabling before turning power off. This will enable later
to add calls to clk_prepare/unprepare in the s5p_mfc_power_off() function
to avoid keeping clocks prepared all the time when driver is bound.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The maximum rate of special clock depends on SoC variant and should
be set in device tree via assigned-clock-rates property, so remove
the code which forces special clock to 200MHz.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some applications don't check error codes from QBUF/DQBUF ioctls,
so don't spam kernel log with errors if they fall into endless loop
trying to queue next buffer after a failure.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We do video allocation all the time and we need it to be fast. Plus TLB
efficiency isn't terribly important for video.
That means we want to set DMA_ATTR_ALLOC_SINGLE_PAGES.
See also the previous change (commit 14d3ae2efe "ARM: dma-mapping: Use
DMA_ATTR_ALLOC_SINGLE_PAGES hint to optimize allocation").
[m.szyprowski: rebased patch onto v4.9-rc1 and adapted changes
to latest videbuf2 changes, this simplifies code changes to
only set proper dma attribute flag and comment the reason
for it, added commit id of arch/arm/mm patch]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Clock control indirectly requires access to MFC device, so call it only
if we are sure that the device exists in s5p_mfc_release function.
s5p_mfc_remove() calls s5p_mfc_final_pm(), which releases all PM related
resources, including clocks, so any call to clocks related functions
is not valid after s5p_mfc_final_pm().
Fixes: d695c12 ("[media] media: s5p-mfc fix invalid memory access from
s5p_mfc_release()")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Newer MFC hardware have internal clock gating feature, so additional
software-triggered clock gating sometimes causes misbehavior of the MFC
firmware and results in freeze or crash. This patch changes the driver
to use software-triggered clock gating only when working with v5 MFC
hardware, where it has been proven to work properly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, when incomplete frame is received in the middle of
decoding, driver treats it as an error, so src/dst queue and
clock are cleaned. Although it is obviously error case, it is
needed to maintain video decoding in case of necessity. This
patch supports skip incomplete frame to next.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Driver complains about too small scratch buffer size. After adjusting
it according to vendor code, decoding works.
[mszyprow: moved the change to the header file]
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Include buffer size in s5p_mfc_alloc_priv_buf() the error message
when it fails to allocate the buffer.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
s5p_mfc_alloc_priv_buf() prints two message to report invalid memory
configuration error. Collapse them into a single message.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
alloc_workqueue replaces deprecated create_singlethread_workqueue().
The MFC device driver is a v4l2 driver which can encode/decode video
raw/elementary streams and has support for all popular video codecs.
The driver's watchdog_workqueue has been replaced with system_wq since
it queues a single work item, &dev->watchdog_work, which calls for no
ordering requirement. The work item is involved in running the watchdog
timer and is not being used on a memory reclaim path.
Work item has been flushed in s5p_mfc_remove() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this a proper typed array. Drop the old allocate context code since
that is no longer used.
Note that the memops functions now get a struct device pointer instead of
the struct device ** that was there initially (actually a void pointer to
a struct containing only a struct device pointer).
This code is now a lot cleaner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Stop using alloc_ctx and just fill in the device pointer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to the V4L2 documentation the driver and card fields should be
used to identify the driver and the device but the s5p-mfc driver fills
those field using the platform device name, which in turn is the name of
the device DT node.
So not only the filled information isn't correct but also the same values
are used in all the fields for both the encoder and decoder video devices.
Before this patch:
Driver Info (not using libv4l2):
Driver name : 11000000.codec
Card type : 11000000.codec
Bus info : platform:11000000.codec
Driver version: 4.7.0
Driver Info (not using libv4l2):
Driver name : 11000000.codec
Card type : 11000000.codec
Bus info : platform:11000000.codec
Driver version: 4.7.0
After this patch:
Driver Info (not using libv4l2):
Driver name : s5p-mfc
Card type : s5p-mfc-dec
Bus info : platform:11000000.codec
Driver version: 4.7.0
Driver Info (not using libv4l2):
Driver name : s5p-mfc
Card type : s5p-mfc-enc
Bus info : platform:11000000.codec
Driver version: 4.7.0
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver doesn't set the struct v4l2_capability bus_info field so the
v4l2-compliance tool reports the following errors for VIDIOC_QUERYCAP:
Required ioctls:
VIDIOC_QUERYCAP returned 0 (Success)
fail: v4l2-compliance.cpp(304): string empty
fail: v4l2-compliance.cpp(528): check_ustring(vcap.bus_info, sizeof(vcap.bus_info))
test VIDIOC_QUERYCAP: FAIL
This patch fixes by setting the field in VIDIOC_QUERYCAP ioctl handler:
Required ioctls:
VIDIOC_QUERYCAP returned 0 (Success)
test VIDIOC_QUERYCAP: OK
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The streaming field in struct vb2_queue is meant to be private and should
not be used by drivers directly, instead the vb2_is_streaming() function
should be used to check the videobuf2 queue streaming status.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The V4L2 documentation says that applications must call the VIDIOC_REQBUFS
ioctl to determine if a memory mapped, user pointer or DMABUF based I/O is
supported by the driver.
For example GStreamer does this by first calling VIDIOC_REQBUFS with count
zero for all the possible streaming I/O methods and then finally doing the
real VIDIOC_REQBUFS with count N using a known to be supported memory type.
But the driver prints an error on VIDIOC_REQBUFS if the memory type is not
supported which leads to the following errors that can confuse the users:
[ 178.704390] vidioc_reqbufs:575: Only V4L2_MEMORY_MMAP is supported
[ 178.704666] vidioc_reqbufs:575: Only V4L2_MEMORY_MMAP is supported
[ 178.714956] vidioc_reqbufs:575: Only V4L2_MEMORY_MMAP is supported
[ 178.715229] vidioc_reqbufs:575: Only V4L2_MEMORY_MMAP is supported
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The function comment has an obvious typo error, so fix it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch fixes the error path in the driver probe, so in case of
any failure, the resources are not leaked.
Reported-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix Decoder and encoder video device double release in probe error path.
video_device_release(dev->vfd_dec) get called twice if decoder register
fails. Also, video_device_release(dev->vfd_enc) get called twice if encoder
register fails.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We don't need to request the sizeimage or num_planes
in try_fmt.
Signed-off-by: ayaka <ayaka@soulik.info>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The encoder forget the work to call hardware to release its buffers.
This patch came from chromium project. I just change its code
style and make the API match with new kernel.
Signed-off-by: ayaka <ayaka@soulik.info>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
User-space applications can use the VIDIOC_REQBUFS ioctl to determine if a
memory mapped, user pointer or DMABUF based I/O is supported by the driver.
So a set of VIDIOC_REQBUFS ioctl calls will be made with count 0 and then
the real VIDIOC_REQBUFS call with count == n. But for count 0, the driver
not only frees the buffer but also closes the MFC instance and s5p_mfc_ctx
state is set to MFCINST_FREE.
The VIDIOC_REQBUFS handler for the output device checks if the s5p_mfc_ctx
state is set to MFCINST_INIT (which happens on an VIDIOC_S_FMT) and fails
otherwise. So after a VIDIOC_REQBUFS(n), future VIDIOC_REQBUFS(n) calls
will fails unless a VIDIOC_S_FMT ioctl calls happens before the reqbufs.
But applications may first set the format and then attempt to determine
the I/O methods supported by the driver (for example Gstramer does it) so
the state won't be set to MFCINST_INIT again and VIDIOC_REQBUFS will fail.
To avoid this issue, only free the buffers on VIDIOC_REQBUFS(0) but don't
close the MFC instance to allow future VIDIOC_REQBUFS(n) calls to succeed.
[javier: Rewrote changelog to explain the problem more detailed]
Signed-off-by: ayaka <ayaka@soulik.info>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Nicolas Dufresne <nicolas@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Failing to get the struct s5p_mfc_pm .clock is a non-fatal error so the
clock field can have a errno pointer value. But s5p_mfc_final_pm() only
checks if .clock is not NULL before attempting to unprepare and put it.
This leads to the following warning in clk_put() due s5p_mfc_final_pm():
WARNING: CPU: 3 PID: 1023 at drivers/clk/clk.c:2814 s5p_mfc_final_pm+0x48/0x74 [s5p_mfc]
CPU: 3 PID: 1023 Comm: rmmod Tainted: G W 4.6.0-rc6-next-20160502-00005-g5a15a49106bc #9
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c010e1bc>] (unwind_backtrace) from [<c010af28>] (show_stack+0x10/0x14)
[<c010af28>] (show_stack) from [<c032485c>] (dump_stack+0x88/0x9c)
[<c032485c>] (dump_stack) from [<c011b8e8>] (__warn+0xe8/0x100)
[<c011b8e8>] (__warn) from [<c011b9b0>] (warn_slowpath_null+0x20/0x28)
[<c011b9b0>] (warn_slowpath_null) from [<bf16004c>] (s5p_mfc_final_pm+0x48/0x74 [s5p_mfc])
[<bf16004c>] (s5p_mfc_final_pm [s5p_mfc]) from [<bf157414>] (s5p_mfc_remove+0x8c/0x94 [s5p_mfc])
[<bf157414>] (s5p_mfc_remove [s5p_mfc]) from [<c03fe1f8>] (platform_drv_remove+0x24/0x3c)
[<c03fe1f8>] (platform_drv_remove) from [<c03fcc70>] (__device_release_driver+0x84/0x110)
[<c03fcc70>] (__device_release_driver) from [<c03fcdd8>] (driver_detach+0xac/0xb0)
[<c03fcdd8>] (driver_detach) from [<c03fbff8>] (bus_remove_driver+0x4c/0xa0)
[<c03fbff8>] (bus_remove_driver) from [<c01886a8>] (SyS_delete_module+0x174/0x1b8)
[<c01886a8>] (SyS_delete_module) from [<c01078c0>] (ret_fast_syscall+0x0/0x3c)
Assign the pointer to NULL in case of a lookup failure to fix the issue.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch fixes build break caused by lack of dma-iommu API on ARM64
(this API is specific to ARM 32bit architecture).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This patch adds support for IOMMU to s5p-mfc device driver. MFC firmware
is limited and it cannot use the default configuration. If IOMMU is
available, the patch disables the default DMA address space
configuration and creates a new address space of size limited to 256M
and base address set to 0x20000000.
For now the same address space is shared by both 'left' and 'right'
memory channels, because the DMA/IOMMU frameworks do not support
configuring them separately. This is not optimal, but besides limiting
total address space available has no other drawbacks (MFC firmware
supports 256M of address space per each channel).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch removes custom code for initialization and handling of
reserved memory regions in s5p-mfc driver and replaces it with generic
reserved memory regions api.
s5p-mfc driver now handles two reserved memory regions defined by
generic reserved memory bindings. Support for non-dt platform has been
removed, because all supported platforms have been already converted to
device tree.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
All multimedia devices found on Exynos SoCs support only contiguous
buffers, so set DMA max segment size to DMA_BIT_MASK(32) to let memory
allocator to correctly create contiguous memory mappings.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The s5p_mfc_probe() function registers the video devices before all the
resources needed by s5p_mfc_open() are correctly initalized.
So if s5p_mfc_open() function is called before s5p_mfc_probe() finishes
(since the video dev is already registered), a NULL pointer dereference
will happen due s5p_mfc_open() accessing uninitialized vars such as the
struct s5p_mfc_dev .watchdog_timer and .mfc_ops fields.
An example is following BUG caused by add_timer() getting a NULL pointer:
[ 45.765374] kernel BUG at kernel/time/timer.c:790!
[ 45.765381] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
...
[ 45.766149] [<c016fdf4>] (mod_timer) from [<bf181d18>] (s5p_mfc_open+0x274/0x4d4 [s5p_mfc])
[ 45.766416] [<bf181d18>] (s5p_mfc_open [s5p_mfc]) from [<bf0214a0>] (v4l2_open+0x9c/0x100 [videodev])
[ 45.766547] [<bf0214a0>] (v4l2_open [videodev]) from [<c01e355c>] (chrdev_open+0x9c/0x178)
[ 45.766575] [<c01e355c>] (chrdev_open) from [<c01dceb4>] (do_dentry_open+0x1e0/0x300)
[ 45.766595] [<c01dceb4>] (do_dentry_open) from [<c01ec2f0>] (path_openat+0x800/0x10d4)
[ 45.766610] [<c01ec2f0>] (path_openat) from [<c01ed8b8>] (do_filp_open+0x5c/0xc0)
[ 45.766624] [<c01ed8b8>] (do_filp_open) from [<c01de218>] (do_sys_open+0x10c/0x1bc)
[ 45.766642] [<c01de218>] (do_sys_open) from [<c01078c0>] (ret_fast_syscall+0x0/0x3c)
[ 45.766655] Code: eaffffe3 e3a00001 e28dd008 e8bd81f0 (e7f001f2)
Fix it by registering the video devs as the last step in s5p_mfc_probe().
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
When s5p_mfc_remove() calls put_device() for the reserved memory region
devs, the driver core warns that the dev doesn't have a release callback:
WARNING: CPU: 0 PID: 591 at drivers/base/core.c:251 device_release+0x8c/0x90
Device 's5p-mfc-l' does not have a release() function, it is broken and must be fixed.
Also, the declared DMA memory using dma_declare_coherent_memory() isn't
relased so add a dev .release that calls dma_release_declared_memory().
Cc: <stable@vger.kernel.org>
Fixes: 6e83e6e25e ("[media] s5p-mfc: Fix kernel warning on memory init")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The devices don't have a name set, so makes dev_name() returns NULL which
makes harder to identify the devices that are causing issues, for example:
WARNING: CPU: 2 PID: 616 at drivers/base/core.c:251 device_release+0x8c/0x90
Device '(null)' does not have a release() function, it is broken and must be fixed.
And after setting the device name:
WARNING: CPU: 0 PID: 591 at drivers/base/core.c:251 device_release+0x8c/0x90
Device 's5p-mfc-l' does not have a release() function, it is broken and must be fixed.
Cc: <stable@vger.kernel.org>
Fixes: 6e83e6e25e ("[media] s5p-mfc: Fix kernel warning on memory init")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Exynos and Samsung S5P platforms has been fully converted to device
tree, so old platform device based init data can be now removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is a new control V4L2_CID_MPEG_VIDEO_FORCE_KEY_FRAME to
force an encoder key frame. It is the same as requesting
V4L2_MPEG_MFC51_VIDEO_FORCE_FRAME_TYPE_I_FRAME.
Signed-off-by: Wu-Cheng Li <wuchengli@chromium.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
MFC register addresses are used only by writel/readl macros which already
takes care of proper register accessing.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both macros can be merged into one.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
MFC driver uses dev->irqlock spinlock to protect queues only, but many context
fields require protection also - they can be accessed concurrently
from IOCTLs and IRQ handler. The patch increases protection range of irqlock
to those fields also.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Many version specific functions are not called by common code, so there
is no need to use callbacks. Additionally some of them are not used at all,
so they can be safely removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Code for queue cleanup has nothing specific to hardware version.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both version of MFC driver use functions with the same body and name.
The patch moves them to common location. It also simplifies it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The s5p_mfc_codec_ops structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move timestamp from struct vb2_v4l2_buffer to struct vb2_buffer
for common use, and change its type to u64 in order to handling
y2038 problem. This patch also includes all device drivers' changes related to
this restructuring.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The queue_setup callback has a void pointer that is just for V4L2
and is the pointer to the v4l2_format struct that was passed to
VIDIOC_CREATE_BUFS. The idea was that drivers would use the information
from that struct to buffers suitable for the requested format.
After the vb2 split series this pointer is now a void pointer,
which is ugly, and the reality is that all existing drivers will
effectively just look at the sizeimage field of v4l2_format.
To make this more generic the queue_setup callback is changed:
the void pointer is dropped, instead if the *num_planes argument
is 0, then use the current format size, if it is non-zero, then
it contains the number of requested planes and the sizes array
contains the requested sizes. If either is unsupported, then return
-EINVAL, otherwise use the requested size(s).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace the obsolete field ctrl_class with "which".
Make sure it not used in future modules by commenting out the field with
ifndef __KERNEL_ .
The field cannot be simply removed because that would be change on the
kenel API to the userspace (and we don't like that).
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace struct v4l2_format * with void * to make queue_setup()
for common use.
And then, modify all device drivers related with this change.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix missing const in fimc-lite.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
MFC driver never delivered EOS event to apps feeding constantly its capture
buffer with fresh buffers. The patch fixes it by marking last buffers
returned by MFC with MFC_BUF_FLAG_EOS flag and firing EOS event on
de-queuing such buffers.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
MFC encoder supports end-of-stream handling for encoder
in version 5 of hardware. This patch adds it also for newer version.
It was successfully tested on MFC-v8.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove v4l2 stuff - v4l2_buf, v4l2_plane - from struct vb2_buffer.
Add new member variables - bytesused, length, offset, userptr, fd,
data_offset - to struct vb2_plane in order to cover all information
of v4l2_plane.
struct vb2_plane {
<snip>
unsigned int bytesused;
unsigned int length;
union {
unsigned int offset;
unsigned long userptr;
int fd;
} m;
unsigned int data_offset;
}
Replace v4l2_buf with new member variables - index, type, memory - which
are common fields for buffer management.
struct vb2_buffer {
<snip>
unsigned int index;
unsigned int type;
unsigned int memory;
unsigned int num_planes;
struct vb2_plane planes[VIDEO_MAX_PLANES];
<snip>
};
v4l2 specific fields - flags, field, timestamp, timecode,
sequence - are moved to vb2_v4l2_buffer in videobuf2-v4l2.c
struct vb2_v4l2_buffer {
struct vb2_buffer vb2_buf;
__u32 flags;
__u32 field;
struct timeval timestamp;
struct v4l2_timecode timecode;
__u32 sequence;
};
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make videobuf2-v4l2 as a wrapper of videobuf2-core for v4l2-use.
And replace videobuf2-core.h with videobuf2-v4l2.h.
This renaming change should be accompanied by the modifications
of all device drivers that include videobuf2-core.h.
It can be done with just running this shell script.
replace()
{
str1=$1
str2=$2
dir=$3
for file in $(find $dir -name *.h -o -name *.c -o -name Makefile)
do
echo $file
sed "s/$str1/$str2/g" $file > $file.out
mv $file.out $file
done
}
replace "videobuf2-core" "videobuf2-v4l2" "include/media/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/media/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/usb/gadget/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/staging/media/"
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Correct misuse of 0x%d in logging message.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV6ifEAAoJEAhfPr2O5OEVn5kP/i2jM1tWcmV/ZEBKGAN0jpRk
5Y/Q+rnXvOpIJSQC3dEkweoBymVMclSgSB/wFSWCZtp5MaB8KrH4/2uc3UvolF91
7bqXt+fCUacMbDQyaabMCR83mz9tdOJLd5sf0ABqBgXGfwh5uXmBPaYBzmcYvKcW
4D89MFUpaFDPARTs9rdpVyr0aPRU4GcN0R3snRO9Ly+cQnyV/RxPf9NqCgnI+yPq
+NvA9ScUBcBt62piSIGR4egcAR8boxYC+0r57340S21/JVMvsHQ3ok9b1aT8/rtd
Yl24FkcKrRV0ShN5S1RmW5DLH/HRGabuMjkiEz9xq52FGD2sQQda0At58dWivsa4
XYdxS9UUfb9Z+qyeMdmCl1MUFRrV2G4H6VItP+GKyT3UZLEDcLl6hBg3SkyWxWB4
CSO5WuRThiIB86OVcIaREftzqDy5HdvH3ZKRD7QrW0DItGVjQwV5j6gvwqO9OEXs
99BnSohyKwUBonumE2ZtFGGhIwIomllrMSqg991bPH9+13bg/rPxUqntkPrVap/9
cV3qKO8ZFrz5UInBnR1U83l60ZK7rV4G6AVMSMKpM9XVK9TDKryAUN9Mhj5XWRH8
hbma89TQVdhdrITtt27uzj8F622cvZvxd1BqDBR8DjKVvtv/E2GPzJrAj7GHe3/o
NgzP5fF6X2Si32GNb7J8
=cIed
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new DVB frontend drivers: ascot2e, cxd2841er, horus3a, lnbh25
- new HDMI capture driver: tc358743
- new driver for NetUP DVB new boards (netup_unidvb)
- IR support for DVBSky cards (smipcie-ir)
- Coda driver has gain macroblock tiling support
- Renesas R-Car gains JPEG codec driver
- new DVB platform driver for STi boards: c8sectpfe
- added documentation for the media core kABI to device-drivers DocBook
- lots of driver fixups, cleanups and improvements
* tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (297 commits)
[media] c8sectpfe: Remove select on undefined LIBELF_32
[media] i2c: fix platform_no_drv_owner.cocci warnings
[media] cx231xx: Use wake_up_interruptible() instead of wake_up_interruptible_nr()
[media] tc358743: only queue subdev notifications if devnode is set
[media] tc358743: add missing Kconfig dependency/select
[media] c8sectpfe: Use %pad to print 'dma_addr_t'
[media] DocBook media: Fix typo "the the" in xml files
[media] tc358743: make reset gpio optional
[media] tc358743: set direction of reset gpio using devm_gpiod_get
[media] dvbdev: document most of the functions/data structs
[media] dvb_frontend.h: document the struct dvb_frontend
[media] dvb-frontend.h: document struct dtv_frontend_properties
[media] dvb-frontend.h: document struct dvb_frontend_ops
[media] dvb: Use DVBFE_ALGO_HW where applicable
[media] dvb_frontend.h: document struct analog_demod_ops
[media] dvb_frontend.h: Document struct dvb_tuner_ops
[media] Docbook: Document struct analog_parameters
[media] dvb_frontend.h: get rid of dvbfe_modcod
[media] add documentation for struct dvb_tuner_info
[media] dvb_frontend: document dvb_frontend_tune_settings
...
MFC hardware is known to trash random memory if one tries to use a
buffer which has lower DMA addresses than the configured DMA base
address. This patch adds a check for this case and proper error
handling.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kamil Debski <kamil@wypas.org>
[s.nawrocki@samsung.com: fixed typo (addres -> address]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
MFCINST_GOT_INST state is set to encoder context with set_format
only for capture buffer. In queue_setup of encoder called during
reqbufs, it is checked MFCINST_GOT_INST state for both capture
and output buffer. So this patch fixes encoder to check
MFCINST_GOT_INST state only for capture buffer from queue_setup.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch fix spelling typo inv various part of sources.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Commits a0f10c131c and
6c9fe76536 ("media: s5p-mfc: fix broken
pointer cast on 64bit arch") fixed issue with lossy cast on 64-bit
architectures. However it also removed __iomem attribute from that cast.
This leads to sparse warnings. This patch fixes those warnings by adding
__iomem cast in case of v6+ code version and replacing readl/writel by
simple u32 load/store operations in case of v5 code (which is called on
system memory allocated by dma_alloc_coherent() instead of io registers).
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Setting the last buffer flag causes the videobuf2 core to return -EPIPE from
DQBUF calls on the capture queue after the last buffer is dequeued.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
[k.debski@samsung.com: Fix misspelling in title (s/sp5/s5p/)]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/platform/s5p-mfc/s5p_mfc.c:1340 s5p_mfc_runtime_resume() warn: this array is probably non-NULL. 'm_dev->alloc_ctx'
alloc_ctx can never be NULL, as it is embeeded inside the struct
s5p_mfc_dev.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
