The link may be up already via the chip's reset strapping, or though action
of U-Boot, or from the last time the interface was brought up. Resetting
the link causes it to go down for several seconds. This can significantly
increase the time from power-on to DHCP completion and a device being
accessible to the network.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The init_phy() function attaches to the PHY, then configures the
SerDes<->TBI link (in SGMII mode). The TBI is on the MDIO bus with the PHY
(sort of) and is accessed via the gianfar's MDIO registers, using the
functions gfar_local_mdio_read/write(), which don't do any locking.
The previously attached PHY will start a work-queue on a timer, and
probably an irq handler as well, which will talk to the PHY and thus use
the MDIO bus. This uses phy_read/write(), which have locking, but not
against the gfar_local_mdio versions.
The result is that PHY code will try to use the MDIO bus at the same time
as the SerDes setup code, corrupting the transfers.
Setting up the SerDes before attaching to the PHY will insure that there is
no race between the SerDes code and *our* PHY, but doesn't fix everything.
Typically the PHYs for all gianfar devices are on the same MDIO bus, which
is associated with the first gianfar device. This means that the first
gianfar's SerDes code could corrupt the MDIO transfers for a different
gianfar's PHY.
The lock used by phy_read/write() is contained in the mii_bus structure,
which is pointed to by the PHY. This is difficult to access from the
gianfar drivers, as there is no link between a gianfar device and the
mii_bus which shares the same MDIO registers. As far as the device layer
and drivers are concerned they are two unrelated devices (which happen to
share registers).
Generally all gianfar devices' PHYs will be on the bus associated with the
first gianfar. But this might not be the case, so simply locking the
gianfar's PHY's mii bus might not lock the mii bus that the SerDes setup
code is going to use.
We solve this by having the code that creates the gianfar platform device
look in the device tree for an mdio device that shares the gianfar's
registers. If one is found the ID of its platform device is saved in the
gianfar's platform data.
A new function in the gianfar mii code, gfar_get_miibus(), can use the bus
ID to search through the platform devices for a gianfar_mdio device with
the right ID. The platform device's driver data is the mii_bus structure,
which the SerDes setup code can use to lock the current bus.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When the at91_ether driver is using a GPIO for its PHY interrupt,
be sure to request (and later, if needed, free) that GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 401c0aabec introduced a regression
in the atl1 driver by storing the VLAN tag in the wrong TX descriptor
field.
This patch causes the VLAN tag to be stored in its proper location.
Tested-by: Ramon Casellas <ramon.casellas@cttc.es>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use mmiowb() to ensure "stop" and "go" commands are sent in order on ia64.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A panic was discovered with bonding when using mode 5 or 6 and trying to
remove the slaves from the bond after the interface was taken down.
When calling 'ifconfig bond0 down' the following happens:
bond_close()
bond_alb_deinitialize()
tlb_deinitialize()
kfree(bond_info->tx_hashtbl)
bond_info->tx_hashtbl = NULL
Unfortunately if there are still slaves in the bond, when removing the
module the following happens:
bonding_exit()
bond_free_all()
bond_release_all()
bond_alb_deinit_slave()
tlb_clear_slave()
tx_hash_table = BOND_ALB_INFO(bond).tx_hashtbl
u32 next_index = tx_hash_table[index].next
As you might guess we panic when trying to access a few entries into the
table that no longer exists.
I experimented with several options (like moving the calls to
tlb_deinitialize somewhere else), but it really makes the most sense to
be part of the bond_close routine. It also didn't seem logical move
tlb_clear_slave around too much, so the simplest option seems to add a
check in tlb_clear_slave to make sure we haven't already wiped the
tx_hashtbl away before searching for all the non-existent hash-table
entries that used to point to the slave as the output interface.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch reworks the resource free logic performed at the time
a bonding device is released. This (a) closes two resource leaks, one
for workqueues and one for multicast lists, and (b) improves commonality
of code between the "destroy one" and "destroy all" paths by performing
final free activity via destructor instead of explicitly (and differently)
in each path.
"Sean E. Millichamp" <sean@bruenor.org> reported the workqueue
leak, and included a different patch.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
During the rework of the mii monitor for:
commit f0c76d6177
Author: Jay Vosburgh <fubar@us.ibm.com>
Date: Wed Jul 2 18:21:58 2008 -0700
bonding: refactor mii monitor
I left out the increment of the link failure counter. This
patch corrects that omission.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: fix irq vectors.
lguest: fix early_ioremap.
lguest: fix example launcher compile after moved asm-x86 dir.
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: remove sched-design.txt from 00-INDEX
sched: change sched_debug's mode to 0444
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ftrace: handle archs that do not support irqs_disabled_flags
do_IRQ: cannot handle IRQ -1 vector 0x20 cpu 0
------------[ cut here ]------------
kernel BUG at arch/x86/kernel/irq_32.c:219!
We're not ISA: we have a 1:1 mapping from vectors to irqs.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
dmi_scan_machine breaks under lguest:
lguest: unhandled trap 14 at 0xc04edeae (0xffa00000)
This is because we use current_cr3 for the read_cr3() paravirt
function, and it isn't set until the first cr3 change. We got away
with it until this happened.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
fix:
arch/x86/kernel/cpu/common.c: In function 'early_identify_cpu':
arch/x86/kernel/cpu/common.c:553: error: 'struct cpuinfo_x86' has no member named 'cpu_index'
as cpu_index is only available on SMP.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix /proc/cpuinfo output on x86/Voyager
Ever since
| commit 92cb7612ae
| Author: Mike Travis <travis@sgi.com>
| Date: Fri Oct 19 20:35:04 2007 +0200
|
| x86: convert cpuinfo_x86 array to a per_cpu array
We've had an extra field in cpuinfo_x86 which is cpu_index.
Unfortunately, voyager has never initialised this, although the only
noticeable impact seems to be that /proc/cpuinfo shows all zeros for
the processor ids.
Anyway, fix this by initialising the boot CPU properly and setting the
index when the secondaries update.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix on x86/Voyager
Given commits like this:
| Author: Suresh Siddha <suresh.b.siddha@intel.com>
| Date: Tue Jul 29 10:29:19 2008 -0700
|
| x86, xsave: enable xsave/xrstor on cpus with xsave support
Which deliberately expose boot cpu dependence to pieces of the system,
I think it's time to explicitly have a variable for it to prevent this
continual misassumption that the boot CPU is zero.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix on non-lockdep architectures
Some architectures do not support a way to read the irq flags that
is set from "local_irq_save(flags)" to determine if interrupts were
disabled or enabled. Ftrace uses this information to display to the user
if the trace occurred with interrupts enabled or disabled.
Besides the fact that those archs that do not support this will fail to
compile, unless they fix it, we do not want to have the trace simply
say interrupts were not disabled or they were enabled, without knowing
the real answer.
This patch adds a 'X' in the output to let the user know that the
architecture they are running on does not support a way for the tracer
to determine if interrupts were enabled or disabled. It also lets those
same archs compile with tracing enabled.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: allow /dev/mem mmaps on non-PAT CPUs/platforms
Fix mmap to /dev/mem when CONFIG_X86_PAT is off and CONFIG_STRICT_DEVMEM is
off
mmap to /dev/mem on kernel memory has been failing since the
introduction of PAT (CONFIG_STRICT_DEVMEM=n case). Seems like
the check to avoid cache aliasing with PAT is kicking in even
when PAT is disabled. The bug seems to have crept in 2.6.26.
This patch makes sure that the mmap to regular
kernel memory succeeds if CONFIG_STRICT_DEVMEM=n and
PAT is disabled, and the checks to avoid cache aliasing
still happens if PAT is enabled.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Tested-by: Tim Sirianni <tim@scalemp.com>
Cc: <stable@kernel.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix build failure on x86/Voyager
Before:
| commit 329513a35d
| Author: Yinghai Lu <yhlu.kernel@gmail.com>
| Date: Wed Jul 2 18:54:40 2008 -0700
|
| x86: move prefill_possible_map calling early
prefill_possible_mask() was hidden under CONFIG_HOTPLUG_CPU rendering
it invisitble to voyager. Since this commit it's exposed, but not
provided by the voyager subarch, so add a dummy stub to fix the link
breakage.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix x86/Voyager boot
CONFIG_SMP is used for features which work on *all* x86 boxes.
CONFIG_X86_SMP is used for standard PC like x86 boxes (for things like
multi core and apics)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: boot up secondary CPUs as well on x86/Voyager systems
This commit:
| commit 3e9704739d
| Author: Glauber Costa <gcosta@redhat.com>
| Date: Wed May 28 13:01:54 2008 -0300
|
| x86: boot secondary cpus through initial_code
removed the use of initialize_secondary. However, it didn't update
voyager, so the secondary cpus no longer boot. Fix this by adding the
initial_code switch to voyager as well.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The nlm_host_rebooted() function uses nlm_cmp_addr() to find an
nsm_handle that matches the rebooted peer. In order for this to work,
the passed-in address must have a proper address family.
This fixes a post-2.6.28 regression introduced by commit 781b61a6, which
added AF_INET6 support to nlm_cmp_addr(). Before that commit,
nlm_cmp_addr() didn't care about the address family; it compared only
the sin_addr.s_addr field for equality.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Before 14f7dd6320 "[PATCH] Copy XFS
readdir hack into nfsd code", readdir_cd->err was reset to eof before
each call to vfs_readdir; afterwards, it is set only once. Similarly,
c002a6c797 "[PATCH] Optimise NFS readdir
hack slightly", can cause us to exit without nfserr_eof set. Fix this.
This ensures the "eof" bit is set when needed in readdir replies. (The
particular case I saw was an nfsv4 readdir of an empty directory, which
returned with no entries (the protocol requires "." and ".." to be
filtered out), but with eof unset.)
Cc: David Woodhouse <David.Woodhouse@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
Fix incompatibility with versions of Perl less than 5.6.0
kbuild: do not include arch/<ARCH>/include/asm in find-sources twice.
kbuild: tag with git revision when git describe is missing
kbuild: prevent modpost from looking for a .cmd file for a static library linked into a module
kbuild: fix KBUILD_EXTRA_SYMBOLS
adjust init section definitions
scripts/checksyscalls.sh: fix for non-gnu sed
scripts/package: don't break if %{_smp_mflags} isn't set
kbuild: setlocalversion: dont include svn change count
kbuild: improve check-symlink
kbuild: mkspec - fix build rpm
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[PATCH] Switch all my contributions stuff to a single common address
[WATCHDOG] pci: use pci_ioremap_bar() in drivers/watchdog
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
CHAR: Delete old and now unused M48T35 RTC driver for SGI IP27.
CHAR: Delete old and now unused DS1286 driver.
MIPS: Sort out CPU type to name translation.
MIPS: Use the new byteorder headers
MIPS: Probe for watch registers on cores of all vendors, not just MTI.
MIPS: Switch FPU emulator trap to BREAK instruction.
MIPS: SMP: Do not initialize __cpu_number_map/__cpu_logical_map for CPU 0.
MIPS: Consider value of c0_ebase when computing value of exception base.
MIPS: Clean up MIPSxx-optimized bitop functions
MIPS: New feature test macro cpu_has_mips_r
MIPS: RBTX4927: Add GPIO-LED support
MIPS: TXx9: Fix RBTX4939 ethernet address initialization
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
fdomain_cs: Sort out modules with duplicate description
pcmcia: Whine harder about use of EXCLUSIVE
pcmcia: IRQ_TYPE_EXCLUSIVE is long obsoleted
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
SUNRPC: Fix potential race in put_rpccred()
SUNRPC: Fix rpcauth_prune_expired
NFS: Convert nfs_attr_generation_counter into an atomic_long
SUNRPC: Respond promptly to server TCP resets
When we close we must clear the extra reference we got when we read
port->tty. Setting the port tty NULL will clear the kref held by the driver
but not the one we obtained ourselves while doing the lookup.
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Helge Hafting <helge.hafting@aitel.hist.no>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-s3c2410: Correct use of ! and &
i2c: The i2c mailing list is moving
scx200_i2c: Add missing class parameter
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: prevent autosuspend during hub initialization
USB: Unusual dev for the "Kyocera / Contax SL300R T*" digital camera.
USB: usbtmc: Use explicit unsigned type for input buffer instead of char*
USB: fix crash when URBs are unlinked after the device is gone
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ASoC: Fix WM9713 ALC Decay Time name
ALSA: ASoC: Fix some minor errors in mpc5200 psc i2s driver
ALSA: ASoC: Fix mono controls after conversion to support full int masks
ALSA: sound/ice1712: indentation & braces disagree - add braces
ALSA: usb - Add quirk for Edirol UA-25EX advanced modes
sound: struct device - replace bus_id with dev_name(), dev_set_name()
ALSA: hda - Add reboot notifier
ALSA: Warn when control names are truncated
ALSA: intel8x0 - add Dell Optiplex GX620 (AD1981B) to AC97 clock whitelist
ALSA: hda - Fix SPDIF mute on IDT/STAC codecs
ALSA: hda: Add HDA vendor ID for Wolfson Microelectronics
ALSA: hda - Add another HP model for AD1884A
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ftrace: fix trace_nop config select
ftrace: perform an initialization for ftrace to enable it
Fix compile error below:
LD drivers/spi/built-in.o
CC [M] drivers/spi/spi_gpio.o
In file included from drivers/spi/spi_gpio.c:26:
include/linux/spi/spi_bitbang.h:23: error: field `work' has incomplete type
make[2]: *** [drivers/spi/spi_gpio.o] Error 1
make[1]: *** [drivers/spi] Error 2
make: *** [drivers] Error 2
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
