The original scrub rate API definition states that if scrub rate
accessors are not implemented, a negative value (-1) should be written
to the sysfs file (/sys/devices/system/edac/mc/mc<N>/sdram_scrub_rate,
where N is the memory controller number on the system). This is
counter-intuitive and awkward at the very least because, when setting
the scrub rate, userspace has to write to sysfs and then read it back to
check error status of the operation.
As Tony notes, best it would be to not have the sdram_scrub_rate in
sysfs if scrub rate support is not implemented. It is too late about
that and a bunch of drivers on a bunch of arches would need to be
changed and tested which is not a trivial task ATM.
Instead, settle for the next best thing of returning -ENODEV when
implementation is missing and -EINVAL when there was an error
encountered while setting the scrub rate.
Reported-by: Han Pingtian <phan@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20110916105856.GA13253@hpt.nay.redhat.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
While initializing the array of csrow attribute instances, a few csrows
were uninitialized. This happened because the module only performed a
check for DRAM base ctl register0's and not DRAM base ctl register1's
chip select enable bit. There could be systems with DIMMs populated
on only single memory channel whereas the module also assumed that a
dual channel dimm had double the memory size of a single memory channel
instead of checking the memory on each channel.
This patch fixes these above issues.
Signed-off-by: Ashish Shenoy <ashenoy@riverbed.com>
Signed-off-by: Prasanna S. Panchamukhi <ppanchamukhi@riverbed.com>
Link: http://lkml.kernel.org/r/4F459CFA.5090604@riverbed.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
For files that are actively using linux/device.h, make sure
that they call it out. This will allow us to clean up some
of the implicit uses of linux/device.h within include/*
without introducing build regressions.
Yes, this was created by "cheating" -- i.e. the headers were
cleaned up, and then the fallout was found and fixed, and then
the two commits were reordered. This ensures we don't introduce
build regressions into the git history.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This provides unified readq()/writeq() helper functions for 32-bit
drivers.
For some cases, readq/writeq without atomicity is harmful, and order of
io access has to be specified explicitly. So in this patch, new two
header files which contain non-atomic readq/writeq are added.
- <asm-generic/io-64-nonatomic-lo-hi.h> provides non-atomic readq/
writeq with the order of lower address -> higher address
- <asm-generic/io-64-nonatomic-hi-lo.h> provides non-atomic readq/
writeq with reversed order
This allows us to remove some readq()s that were added drivers when the
default non-atomic ones were removed in commit dbee8a0aff ("x86:
remove 32-bit versions of readq()/writeq()")
The drivers which need readq/writeq but can do with the non-atomic ones
must add the line:
#include <asm-generic/io-64-nonatomic-lo-hi.h> /* or hi-lo.h */
But this will be nop in 64-bit environments, and no other #ifdefs are
required. So I believe that this patch can solve the problem of
1. driver-specific readq/writeq
2. atomicity and order of io access
This patch is tested with building allyesconfig and allmodconfig as
ARCH=x86 and ARCH=i386 on top of tip/master.
Cc: Kashyap Desai <Kashyap.Desai@lsi.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: James Bottomley <James.Bottomley@parallels.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: James Bottomley <jbottomley@parallels.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hitoshi Mitake <h.mitake@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Several fields in struct cpuinfo_x86 were not defined for the
!SMP case, likely to save space. However, those fields still
have some meaning for UP, and keeping them allows some #ifdef
removal from other files. The additional size of the UP kernel
from this change is not significant enough to worry about
keeping up the distinction:
text data bss dec hex filename
4737168 506459 972040 6215667 5ed7f3 vmlinux.o.before
4737444 506459 972040 6215943 5ed907 vmlinux.o.after
for a difference of 276 bytes for an example UP config.
If someone wants those 276 bytes back badly then it should
be implemented in a cleaner way.
Signed-off-by: Kevin Winchester <kjwinchester@gmail.com>
Cc: Steffen Persvold <sp@numascale.com>
Link: http://lkml.kernel.org/r/1324428742-12498-1-git-send-email-kjwinchester@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No functionality change, this is done so that in a follow-on patch all
queued-up MCEs can be decoded after registering on the chain.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The below patch fixes some typos in various parts of the kernel, as well as fixes some comments.
Please let me know if I missed anything, and I will try to get it changed and resent.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
compatible in dts has been changed, so the driver needs to be updated
accordingly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/p3060qds: Add support for P3060QDS board
powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
powerpc/85xx: Make kexec to interate over online cpus
powerpc/fsl_booke: Fix comment in head_fsl_booke.S
powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
powerpc/86xx: Correct Gianfar support for GE boards
powerpc/cpm: Clear muram before it is in use.
drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
powerpc/fsl_msi: add support for "msi-address-64" property
powerpc/85xx: Setup secondary cores PIR with hard SMP id
powerpc/fsl-booke: Fix settlbcam for 64-bit
powerpc/85xx: Adding DCSR node to dtsi device trees
powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
powerpc/85xx: fix PHYS_64BIT selection for P1022DS
powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
powerpc: respect mem= setting for early memory limit setup
powerpc: Update corenet64_smp_defconfig
powerpc: Update mpc85xx/corenet 32-bit defconfigs
...
Fix up trivial conflicts in:
- arch/powerpc/configs/40x/hcu4_defconfig
removed stale file, edited elsewhere
- arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
added opal and gelic drivers vs added ePAPR driver
- drivers/tty/serial/8250.c
moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support
The sb_edac driver is marginally useful on a 32-bit kernel, and
currently has 64-bit divide compile errors when building that config.
For now, make this build on only for 64-bit kernels.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac: (21 commits)
MAINTAINERS: add an entry for Edac Sandy Bridge driver
edac: tag sb_edac as EXPERIMENTAL, as it requires more testing
EDAC: Fix incorrect edac mode reporting in sb_edac
edac: sb_edac: Add it to the building system
edac: Add an experimental new driver to support Sandy Bridge CPU's
i7300_edac: Fix error cleanup logic
i7core_edac: Initialize memory name with cpu, channel, bank
i7core_edac: Fix compilation on 32 bits arch
i7core_edac: scrubbing fixups
EDAC: Correct Kconfig dependencies
i7core_edac: return -ENODEV if no MC is found
i7core_edac: use edac's own way to print errors
MAINTAINERS: remove dropped edac_mce.* from the file
i7core_edac: Drop the edac_mce facility
x86, MCE: Use notifier chain only for MCE decoding
EDAC i7core: Use mce socketid for better compatibility
i7core_edac: Don't enable memory scrubbing for Xeon 35xx
i7core_edac: Add scrubbing support
edac: Move edac main structs to include/linux/edac.h
i7core_edac: Fix oops when trying to inject errors
...
The edac driver for Sandy Bridge was found to be reporting "FPM"
for edac_mode, which clearly doesn't make sense. It was found that
sb_edac.c:get_dimm_config was reusing a variable for both mem_type
and edac_type, and thus was overwriting the value after setting
it correctly. This patch fixes that issue.
Before the patch:
/sys/devices/system/edac/mc/mc0/csrow0/edac_mode:FPM
/sys/devices/system/edac/mc/mc0/csrow1/edac_mode:FPM
/sys/devices/system/edac/mc/mc0/csrow2/edac_mode:FPM
/sys/devices/system/edac/mc/mc0/csrow3/edac_mode:FPM
After:
/sys/devices/system/edac/mc/mc0/csrow0/edac_mode:S4ECD4ED
/sys/devices/system/edac/mc/mc0/csrow1/edac_mode:S4ECD4ED
/sys/devices/system/edac/mc/mc0/csrow2/edac_mode:S4ECD4ED
/sys/devices/system/edac/mc/mc0/csrow3/edac_mode:S4ECD4ED
Signed-off-by: Mark A. Grondona <mgrondona@llnl.gov>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some changes on it were required due to changeset cd90cc84c6bf0, that
changed the glue with the MCE logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is known to work on mine and Tony's test environments,
using software error injection, and a partial hardware/software
error injection tool.
There's no broader range test yet to double check if the error decoding
logic will actually point to the right DIMM, so use it with care.
More tests are required to be sure that the driver will work on all
different types of memory configurations.
If you're willing to risk using it, I suggest you to enable EDAC debugs
for your test machines, as the debug logs helps to track what's going
inside the driver.
Please feed me with bug reports, if you notice that the driver
is miss-behaving.
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The error cleanup logic was broken. Due to that, one error is generated for
every error polling.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
on i386:
ERROR: "__udivdi3" [drivers/edac/i7core_edac.ko] undefined!\
In both get_sdram_scrub_rate() and set_sdram_scrub_rate()
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get a more reliable DCLK value from DMI, name the SCRUBINTERVAL mask
and guard against potential overflow in the scrub rate computations.
Signed-off-by: Nils Carlson <nils.carlson@ericsson.com>
Both AMD and Intel i7 EDAC drivers use MCE features and are thus
dependent of this functionality present in the kernel. Express this in
Kconfig so that randconfig builds don't break.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Nehalem-EX uses a different memory controller. However, as the
memory controller is not visible on some Nehalem/Nehalem-EP, we
need to indirectly probe via a X58 PCI device. The same devices
are found on (some) Nehalem-EX. So, on those machines, the
probe routine needs to return -ENODEV, as the actual Memory
Controller registers won't be detected.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove edac_mce pieces and use the normal MCE decoder notifier chain by
retaining the same functionality with considerably less code.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This file really needs the full module.h header file present, but
was just getting it implicitly before. Fix it up in advance so we
avoid build failures once the cleanup commit is present.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
mce->socketid and cpu_data(mce->cpu).phys_proc_id are the same,
compare with mce_setup (in mce.c):
m->cpu = m->extcpu = smp_processor_id();
...
m->socketid = cpu_data(m->extcpu).phys_proc_id;
This makes it easier for example for XEN patches to hook into
the MCE subsystem.
Compile tested on x86_64.
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: JBeulich@novell.com
CC: linux-edac@vger.kernel.org
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Add scrubbing support to i7core_edac, tested on intel Xeon L5638.
Signed-off-by: Samuel Gabrielsson <samuel.gabrielsson@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As we'll need to use those structs for trace functions, they should
be on a more public place. So, move struct mem_ctl_info & friends
to edac.h.
No functional changes on this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Error injection needs the pci device 0:0. So, we need to revert
this changeset: 79daef2099.
Tests need to be made to be sure that refcount won't be wrong
as noticed before.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
the clean up achieves:
1. fix warning on 32-bit compile
2. reorder info extraction for clarity
3. add error-trap diagnostic message
4. handle ALL modes of memory configurations
Signed-off-by: Arvind R. <arvino55@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Sparse complains that edac_cap was declared as dev_type and we are
returning edac_type. Historically, edac_type was correct but since
then we have changed it to return a bit field.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: http://lkml.kernel.org/r/20111006063025.GA2615@mwanda
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
When accessing the scrub rate control register (F3x58) on F15h, the DRAM
controller selector (F1x10C[DctCfgSel]) has to point to DCT0 so that the
scrub rate configuration can take effect. See Erratum 505 in the AMD
F15h revision guide for more details.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Drop third nbcfg argument which is old remains and not required anymore.
No functionality change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
MCE decoding code is reporting the core which encountered the error
unconditionally now so drop this piece. Besides, it reported the
coreid in the local processor package which is not that valuable as a
datapoint.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The MCi_STATUS bank has a AddrV bit which, when set, denotes that the
corresponding MCi_ADDR MSR contains a valid address belonging to the
MCE currently being reported. Dump it since it is definitely relevant
information.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Currently, correctable ECCs go through mcelog and do not print the scary
MCE banner. In that case, however, reporting the core where the CECC
happened is important information so dump it along with the decoded
string albeit at risk of having a minor redundancy.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
If second CPU is not enabled, CPC925 EDAC driver will spill out warnings
about errors on second Processor Interface. Support masking that out,
by detecting at runtime which CPUs are present in device tree.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Based on a patch from the PaX Team, found during a clang analysis pass.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: PaX Team <pageexec@freemail.hu>
Cc: stable@kernel.org [v2.6.35+]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 4018294b53 broke the ppc4xx_edac driver at
line 210 where the struct member is missing a comma.
Signed-off-by: Mike Williams <mike@mikebwilliams.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
This reverts commit af9d220bac.
It turns out that one was meant to be applied on top of the edac.git
tree in -next that has more i7core_edac changes, but that wasn't clear
in the original email.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both AMD and Intel i7 EDAC drivers use MCE features and are thus
dependent of this functionality present in the kernel. Express this in
Kconfig so that randconfig builds don't break.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Parameter offset_in_page in edac_mc_handle_ce() should mask the higher
bits above the page size, not the lower bits. The original input
sometimes causes a crash.
Signed-off-by: Kai.Jiang <Kai.Jiang@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
gfs2: Drop __TIME__ usage
isdn/diva: Drop __TIME__ usage
atm: Drop __TIME__ usage
dlm: Drop __TIME__ usage
wan/pc300: Drop __TIME__ usage
parport: Drop __TIME__ usage
hdlcdrv: Drop __TIME__ usage
baycom: Drop __TIME__ usage
pmcraid: Drop __DATE__ usage
edac: Drop __DATE__ usage
rio: Drop __DATE__ usage
scsi/wd33c93: Drop __TIME__ usage
scsi/in2000: Drop __TIME__ usage
aacraid: Drop __TIME__ usage
media/cx231xx: Drop __TIME__ usage
media/radio-maxiradio: Drop __TIME__ usage
nozomi: Drop __TIME__ usage
cyclades: Drop __TIME__ usage
The presense of a writeq() implementation on 32-bit x86 that splits the
64-bit write into two 32-bit writes turns out to break the mpt2sas driver
(and in general is risky for drivers as was discussed in
<http://lkml.kernel.org/r/adaab6c1h7c.fsf@cisco.com>). To fix this,
revert 2c5643b1c5 ("x86: provide readq()/writeq() on 32-bit too") and
follow-on cleanups.
This unfortunately leads to pushing non-atomic definitions of readq() and
write() to various x86-only drivers that in the meantime started using the
definitions in the x86 version of <asm/io.h>. However as discussed
exhaustively, this is actually the right thing to do, because the right
way to split a 64-bit transaction is hardware dependent and therefore
belongs in the hardware driver (eg mpt2sas needs a spinlock to make sure
no other accesses occur in between the two halves of the access).
Build tested on 32- and 64-bit x86 allmodconfig.
Link: http://lkml.kernel.org/r/x86-32-writeq-is-broken@mdm.bga.com
Acked-by: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Kashyap Desai <Kashyap.Desai@lsi.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Acked-by: James Bottomley <James.Bottomley@parallels.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
F15h CPUs may report a non-DRAM address when reporting an error address
belonging to a CC6 state save area. Add a workaround to detect this
condition and compute the actual DRAM address of the error as documented
in the Revision Guide for AMD Family 15h Models 00h-0Fh Processors.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
F15h and later use a portion of DRAM as a CC6 storage area. BIOS
programs D18F1x[17C:140,7C:40] DRAM Base/Limit accordingly by
subtracting the storage area from the DRAM limit setting. However, in
order for edac to consider that part of DRAM too, we need to include it
into the per-node range.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This warning was wrongfully added for a normal condition - intlvsel
actually selects the destination node when node interleaving is enabled
and it is not a mismatch. For a detailed example, see section 2.8.10.2
"Node Interleaving" in F10h BKDG.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This patch removes superfluous debugging output in the sysfs scrub rate
handler. It also consolidates the error handling in the scrub rate
accessors.
Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: bluesmoke-devel@lists.sourceforge.net
Cc: linux-edac@vger.kernel.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
We check the pointers together but at least one of them could be invalid
due to failed allocation. Since we cannot continue if either of the two
allocations has failed, exit early by freeing them both.
Cc: <stable@kernel.org> # 38.x
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (27 commits)
arch/tile: support newer binutils assembler shift semantics
arch/tile: fix deadlock bugs in rwlock implementation
drivers/edac: provide support for tile architecture
tile on-chip network driver: sync up with latest fixes
arch/tile: support 4KB page size as well as 64KB
arch/tile: add some more VMSPLIT options and use consistent naming
arch/tile: fix some comments and whitespace
arch/tile: export some additional module symbols
arch/tile: enhance existing finv_buffer_remote() routine
arch/tile: fix two bugs in the backtracer code
arch/tile: use extended assembly to inline __mb_incoherent()
arch/tile: use a cleaner technique to enable interrupt for cpu_idle()
arch/tile: sync up with <arch/sim.h> and <arch/sim_def.h> changes
arch/tile: fix reversed test of strict_strtol() return value
arch/tile: avoid a simulator warning during bootup
arch/tile: export <asm/hardwall.h> to userspace
arch/tile: warn and retry if an IPI is not accepted by the target cpu
arch/tile: stop disabling INTCTRL_1 interrupts during hypervisor downcalls
arch/tile: fix __ndelay etc to work better
arch/tile: bug fix: exec'ed task thought it was still single-stepping
...
Fix up trivial conflict in arch/tile/kernel/vmlinux.lds.S (percpu
alignment vs section naming convention fix)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (38 commits)
amd64_edac: Fix decode_syndrome types
amd64_edac: Fix DCT argument type
amd64_edac: Fix ranges signedness
amd64_edac: Drop local variable
amd64_edac: Fix PCI config addressing types
amd64_edac: Fix DRAM base macros
amd64_edac: Fix node id signedness
amd64_edac: Drop redundant declarations
amd64_edac: Enable driver on F15h
amd64_edac: Adjust ECC symbol size to F15h
amd64_edac: Simplify scrubrate setting
PCI: Rename CPU PCI id define
amd64_edac: Improve DRAM address mapping
amd64_edac: Sanitize ->read_dram_ctl_register
amd64_edac: Adjust sys_addr to chip select conversion routine to F15h
amd64_edac: Beef up early exit reporting
amd64_edac: Revamp online spare handling
amd64_edac: Fix channel interleave removal
amd64_edac: Correct node interleaving removal
amd64_edac: Add support for interleaved region swapping
...
Fix up trivial conflict in include/linux/pci_ids.h due to
AMD_15H_NB_MISC being renamed as AMD_15H_NB_F3 next to the new
AMD_15H_NB_LINK entry.
Fix amd64_debug_display_dimm_sizes() arguments order per convention (pvt
is always first). Also, the now second arg denotes the DCT so adjust its
type.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
A node id can never be negative since we use it as an index into
the DRAM ranges array. This also makes one of the BUG_ON conditions
redundant.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add the PCI device ids required for driver registration. Remove
pvt->ctl_name and use the family descriptor directly, instead. Then,
bump driver version and fixup its format. Finally, enable DRAM ECC
decoding on F15h.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
F15h has the same ECC symbol size options as F10h revD and later so
adjust checks to that. Simplify code a bit.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Drop static tables which map the bits in F2x80 to a chip select size in
favor of functions doing the mapping with some bit fiddling. Also, add
F15 support.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This function is relevant for F10h and higher, and it has only one
callsite so drop its function pointer from the low_ops struct.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
F15h sys_addr to chip select mapping is almost identical to F10h's so
reuse that. Rename functions on that path accordingly.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Replace per-DCT macros with smarter ones, drop hack and look for the
spare rank on all chip selects on a channel.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
When node interleaving is enabled, a subset of the addr[14:12] bits has
to be removed in order to get the normalized DCT address of the DRAM
channel. The actual number of bits to remove is determined by F1x[1,
0][7C:40][IntlvEn]. Do this correctly.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
On revC3 and revE Fam10h machines and later, non-interleaved graphics
framebuffer memory under the 16G mark can be swapped with a region
located at the bottom of memory so that the GPU can use the interleaved
region and thus two channels. Add support for that.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The address bits from MC4_STATUS differ only between K8 and the rest so
no need for a per-family method.
No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Use the struct mce directly instead of copying from it into a custom
struct err_regs.
No functionality change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The only difference is that F10h used to sport ganged DCTs and F15h
doesn't so adjust the F10h routine and reuse it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Remove reporting of errors with UC bit set - this is done by the MCE
decoding code anyway and this driver deals with DRAM ECC errors only. UC
(NB uncorrectable error) doesn't necessarily mean it is a DRAM error.
Remove unused macros while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The fact whether we are chipkill capable or not does not have any
bearing when computing the channel index on a ganged DCT configuration
so remove that. Also, simplify debug statements. Finally, remove old
error injection leftovers, while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Remove family names from macro names, drop single bit defines and
comment their meaning instead.
No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
* Restrict DCT ganged mode check since only Fam10h supports it
* Adjust DRAM type detection for BD since it only supports DDR3
* Remove second and thus unneeded DCLR read in k8_early_channel_count() - we do
that in read_mc_regs()
* Cleanup comments and remove family names from register macros
* Remove unused defines
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Do not read DBAM regs twice and simplify code around them.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This function maps the system address to the normalized DCT address.
Document what the code does for more clarity and wrap insane bitmasks in
a more understandable macro which generates them. Also, reduce number of
arguments passed to the function. Finally, rename this function to what
it actually does.
No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cleanup and simplify f10_determine_channel(); make it more readable.
Also drop f10_map_intlv_en_to_shift() in favor of simply counting the
bits in F1x124[DramIntlvEn] which is equivalent.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add a struct representing the DRAM chip select base/limit register
pairs. Concentrate all CS handling in a single function. Also, add CS
looping macros for cleaner, more readable code. While at it, adjust code
to F15h. Finally, do smaller macro names cleanups (remove family names
from register macros) and debug messages clarification.
No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add a struct representing the DRAM base/limit range pairs and remove all
cached subfields. Replace them with accessor functions, which actually
saves us some space:
text data bss dec hex filename
14712 1577 336 16625 40f1 drivers/edac/amd64_edac_mod.o.after
14831 1609 336 16776 4188 drivers/edac/amd64_edac_mod.o.before
Also, it simplifies the code a lot allowing to merge the K8 and F10h
routines.
No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
F15h "multiplexes" between the configuration space of the two DRAM
controllers by toggling D18F1x10C[DctCfgSel] while F10h has a different
set of registers for DCT0, and DCT1 in extended PCI config space.
Add DCT configuration space accessors per family thus wrapping all the
different access prerequisites. Clean up code while at it, shorten
names.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Raise the debug level of these routines so that their output get issued
out only when the highest debug level is selected. Otherwise, don't
pollute driver debug output.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add tile support for the EDAC driver, which provides unified system
error (memory, PCI, etc.) reporting. For now, the TILEPro port
reports memory correctable error (CE) only.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Get rid of old users of of_platform_driver in arch/powerpc. Most
of_platform_driver users can be converted to use the platform_bus
directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
to edac-core
fix the totally wrong info w.r.t page,row,dimm-label previously reported to
edac-core by i82975x driver
Signed-off-by: Arvind R. <arvino55@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
amd64_debug_display_dimm_sizes() reports the distribution of the DIMMs
on each DRAM controller and its chip select sizes. Thus, the last don't
have anything to do with whether we're running in ganged DCT mode or not
- their sizes don't change all of a sudden. Fix that by removing the
ganged-check and dump DCT0's config for DCT1 when in ganged mode since
they're identical.
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Fix a bunch of
warning: ‘inline’ is not at beginning of declaration
messages when building a 'make allyesconfig' kernel with -Wextra.
These warnings are trivial to kill, yet rather annoying when building with
-Wextra.
The more we can cut down on pointless crap like this the better (IMHO).
A previous patch to do this for a 'allnoconfig' build has already been
merged. This just takes the cleanup a little further.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Minor formatting fixup since the information which core was associated
with the MCE is not always valid.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Building for X86_32 produces shift count warnings, so use BIT_64() to
eliminate the warnings.
drivers/edac/mce_amd.c:778: warning: left shift count >= width of type
drivers/edac/mce_amd.c:778: warning: left shift count >= width of type
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: bluesmoke-devel@lists.sourceforge.net
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Now that everything is inplace, enable MCE decoding on F15h. Make
initcall routine a bit more readable.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Shorten up MCi_STATUS flags and add BD's new deferred and poison types.
Also, simplify formatting.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
MCE bank 2 is redefined from a BU to a CU (Combined Unit) bank on F15h.
Add a decoder function for CU MCEs.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add a decoder for F15h DC MCEs to support the new types of DC MCEs
introduced by the BD microarchitecture.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
F15h enlarges the extended error code of an MCE to a 5-bit field
(MCi_STATUS[20:16]). Add a mask variable which default 0xf is overridden
on F15h.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
K8 does not allow for an atomic RMW to a cacheline as F10h does so
disable the error injection interface for it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Make the ->{get|set}_sdram_scrub_rate return the actual scrub rate
bandwidth it succeeded setting and remove superfluous arg pointer used
for that. A negative value returned still means that an error occurred
while setting the scrubrate. Document this for future reference.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Now that all prerequisites are in place, drop the two-stage driver
instances initialization in favor of the following simple init sequence:
1. Probe PCI device: we only test ECC capabilities here and if none exit
early.
2. If the hw supports ECC and it is/can be enabled, we init the per-node
instance.
Remove "amd64_" prefix from static functions touched, while at it.
There actually should be no visible functional change resulting from
this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Rework the code to check the hardware ECC capabilities at PCI probing
time. We do all further initialization only if we actually can/have ECC
enabled.
While at it:
0. Fix function naming.
1. Simplify/clarify debug output.
2. Remove amd64_ prefix from the static functions
3. Reorganize code.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This is in preparation for the init path reorganization where we want
only to
1) test whether a particular node supports ECC
2) can it be enabled
and only then do the necessary allocation/initialization. For that,
we need to decouple the ECC settings of the node from the instance's
descriptor.
The should be no functional change introduced by this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
PCI ECS is being enabled by default since 2.6.26 on AMD so this code is
just superfluous now, remove it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Remove static allocation in favor of dynamically allocating space for as
many driver instances as northbridges present on the system.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add a macro per printk level, shorten up error messages. Add relevant
information to KERN_INFO level. No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Rename variables representing PCI devices to their BKDG names for faster
search and shorter, clearer code.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Move the remaining per-family init code into the proper place and
simplify the rest of the initialization. Reorganize error handling in
amd64_init_one_instance().
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Run a per-family init function which does all the settings based on
the family this driver instance is running on. Move the scrubrate
calculation in it and simplify code.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
* 'x86-amd-nb-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, cacheinfo: Cleanup L3 cache index disable support
x86, amd-nb: Cleanup AMD northbridge caching code
x86, amd-nb: Complete the rename of AMD NB and related code
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
When matching error address to the range contained by one memory node,
we're in valid range when node interleaving
1. is disabled, or
2. enabled and when the address bits we interleave on match the
interleave selector on this node (see the "Node Interleaving" section in
the BKDG for an enlightening example).
Thus, when we early-exit, we need to reverse the compound logic
statement properly.
Cc: <stable@kernel.org>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This corrects the misprint introduced when moving '#if
PAGE_SHIFT' from i7core_edac.c to edac_core.h (commit
e9144601d3)
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andrei Konovalov <akonovalov@mvista.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
00740c5854 changed edac_core to
un-/register a workqueue item only if a lowlevel driver supplies a
polling routine. Normally, when we remove a polling low-level driver, we
go and cancel all the queued work. However, the workqueue unreg happens
based on the ->op_state setting, and edac_mc_del_mc() sets this to
OP_OFFLINE _before_ we cancel the work item, leading to NULL ptr oops on
the workqueue list.
Fix it by putting the unreg stuff in proper order.
Cc: <stable@kernel.org> #36.x
Reported-and-tested-by: Tobias Karnat <tobias.karnat@googlemail.com>
LKML-Reference: <1291201307.3029.21.camel@Tobias-Karnat>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Otherwise, variable i will be -1 inside the latest iteration of the
while loop.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Change EDAC's Makefile to use <modules>-y instead of
<modules>-objs because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
[bp: Fixup commit message]
[bp: Fixup indentation]
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Support more than just the "Misc Control" part of the northbridges.
Support more flags by turning "gart_supported" into a single bit flag
that is stored in a flags member. Clean up related code by using a set
of functions (amd_nb_num(), amd_nb_has_feature() and node_to_amd_nb())
instead of accessing the NB data structures directly. Reorder the
initialization code and put the GART flush words caching in a separate
function.
Signed-off-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Not only the naming of the files was confusing, it was even more so for
the function and variable names.
Renamed the K8 NB and NUMA stuff that is also used on other AMD
platforms. This also renames the CONFIG_K8_NUMA option to
CONFIG_AMD_NUMA and the related file k8topology_64.c to
amdtopology_64.c. No functional changes intended.
Signed-off-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/i7core: (34 commits)
i7core_edac: return -ENODEV when devices were already probed
i7core_edac: properly terminate pci_dev_table
i7core_edac: Avoid PCI refcount to reach zero on successive load/reload
i7core_edac: Fix refcount error at PCI devices
i7core_edac: it is safe to i7core_unregister_mci() when mci=NULL
i7core_edac: Fix an oops at i7core probe
i7core_edac: Remove unused member channels in i7core_pvt
i7core_edac: Remove unused arg csrow from get_dimm_config
i7core_edac: Reduce args of i7core_register_mci
i7core_edac: Introduce i7core_unregister_mci
i7core_edac: Use saved pointers
i7core_edac: Check probe counter in i7core_remove
i7core_edac: Call pci_dev_put() when alloc_i7core_dev() failed
i7core_edac: Fix error path of i7core_register_mci
i7core_edac: Fix order of lines in i7core_register_mci
i7core_edac: Always do get/put for all devices
i7core_edac: Introduce i7core_pci_ctl_create/release
i7core_edac: Introduce free_i7core_dev
i7core_edac: Introduce alloc_i7core_dev
i7core_edac: Reduce args of i7core_get_onedevice
...
* 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/edac: (25 commits)
i7300_edac: Properly initialize per-csrow memory size
V4L/DVB: i7300_edac: better initialize page counts
MAINTAINERS: Add maintainer for i7300-edac driver
i7300-edac: CodingStyle cleanup
i7300_edac: Improve comments
i7300_edac: Cleanup: reorganize the file contents
i7300_edac: Properly detect channel on CE errors
i7300_edac: enrich FBD error info for corrected errors
i7300_edac: enrich FBD error info for fatal errors
i7300_edac: pre-allocate a buffer used to prepare err messages
i7300_edac: Fix MTR x4/x8 detection logic
i7300_edac: Make the debug messages coherent with the others
i7300_edac: Cleanup: remove get_error_info logic
i7300_edac: Add a code to cleanup error registers
i7300_edac: Add support for reporting FBD errors
i7300_edac: Properly detect the type of error correction
i7300_edac: Detect if the device is on single mode
i7300_edac: Adds detection for enhanced scrub mode on x8
i7300_edac: Clear the error bit after reading
i7300_edac: Add error detection code for global errors
...
Due to the nature of i7core, we need to probe and attach all PCI
devices used by this driver during the first time probe is called.
However, PCI core will call the probe routine one time for each CPU
socket. If we return -EINVAL to those calls, it would seem that the
driver fails, when, in fact, there's no more devices left to initialize.
Changing the return code to -ENODEV solves this issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At pci_xeon_fixup(), it waits for a null-terminated table, while at
i7core_get_all_devices, it just do a for 0..ARRAY_SIZE. As other tables
are zero-terminated, change it to be terminate with 0 as well, and fixes
a bug where it may be running out of the table elements.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That's a nasty bug that took me a lot of time to track, and whose
solution took just one line to solve. The best fragrances and the worse
poisons are shipped on the smalest bottles.
The drivers/pci/quick.c implements the pci_get_device function. The normal
behavior is that you call it, the function returns you a pdev pointer
and increment pdev->kobj.kref.refcount of the pci device. However,
if you want to keep searching an object, you need to pass the previous
pdev function to the search.
When you use a not null pointer to pdev "from" field, pci_get_device
will decrement pdev->kobj.kref.refcount, assuming that the driver won't
be using the previous pdev.
The solution is simple: we just need to call pci_dev_get() manually,
for the pdev's that the driver will actually use.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Probably due to a bug or some testing logic at PCI level, device
refcount for <bus>:00.0 device is decremented at the end of the
pci_get_device, made by i7core_get_all_devices(). The fact is that
the first versions of the driver relied on those devices to probe
for Nehalem, but the current versions don't use it at all.
So, let's just remove those devices from the driver, making it simpler
and fixing the bug.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
changeset c91d57ba9ce5b5c93a7077e2f72510eb1f9131c4 moved the init
of the priv pointer to the end of the probe routine. However, we need
them before that, otherwise, we hit an OOPS:
[ 67.743453] EDAC DEBUG: mci_bind_devs: Associated fn 0.0, dev = ffff88011b46e000, socket 0
[ 67.751861] BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
[ 67.759685] IP: [<ffffffffa017e484>] i7core_probe+0x979/0x130c [i7core_edac]
[ 67.766721] PGD 10bd38067 PUD 10bd37067 PMD 0
[ 67.771178] Oops: 0000 [#1] SMP
[ 67.774414] last sysfs file: /sys/devices/system/cpu/cpu1/cache/index2/shared_cpu_map
[ 67.782213] CPU 1
[ 67.784042] Modules linked in: i7core_edac(+) edac_core cpufreq_ondemand binfmt_misc dm_multipath video output pci_slot snd_hda_codd
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We can check the number of channels in i7core_register_mci.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In i7core_probe, when setup of mci for 2nd or later socket failed,
we should cleanup prepared mci for 1st socket or so before "put" of
all devices.
So let have i7core_unregister_mci that can be shared between here
and i7core_remove.
While here fix a typo "hanler".
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prevent i7core_remove from running multiple times.
Otherwise value proved will be negative and something will be wrong.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The flag is_registered is not initialized until mci_bind_devs()
is called. Refer it properly.
The mci->dev and mci->edac_check is required in edac_mc_add_mc(),
so prepare them just before the call.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We already do 'get' for all sockets at once. So do 'put' in the
same way.
And let args of the 'get' function to void since it handles
only the single, static and known size table pci_dev_table[].
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Have a couple of method.
while here sort out lines in the i7core_register_mci() a bit.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Have a method to make a couple with alloc_i7core_dev() previously
introduced. Using in pair will help proper resource handling.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's nice to have a method for a single purpose.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since we need to pass the index of the entry, pass the table itself
instead of passing individual members of the table.
While here make it static.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
commit 47251b4d960bdfa648b0d06dbc6d445f41cb3906 have changed
the logic for unexplained reasons. It looks strange that it
can release i7core_dev without calling i7core_put_devices()
that releases i7core_dev->pdev.
Fix the part.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The legacy PCI probe sometimes cause hangs. Better to have it
disabled by default, and have a parameter to enable it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a nasty bug. Since kobject count will be reduced by zero by
edac_mc_del_mc(), and this triggers the kobj release method, the
mci memory will be freed automatically. So, all we have left is ctl_name,
as shown by enabling debug:
[ 80.822186] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 1020: edac_remove_sysfs_mci_device() remove_link
[ 80.832590] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 1024: edac_remove_sysfs_mci_device() remove_mci_instance
[ 80.843776] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 640: edac_mci_control_release() mci instance idx=0 releasing
[ 80.855163] EDAC MC: Removed device 0 for i7core_edac.c i7 core #0: DEV 0000:3f:03.0
[ 80.862936] EDAC DEBUG: in drivers/edac/i7core_edac.c, line at 2089: (null): free structs
[ 80.871134] EDAC DEBUG: in drivers/edac/edac_mc.c, line at 238: edac_mc_free()
[ 80.878379] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 726: edac_mc_unregister_sysfs_main_kobj()
[ 80.888043] EDAC DEBUG: in drivers/edac/i7core_edac.c, line at 1232: drivers/edac/i7core_edac.c: i7core_put_devices()
Also, kfree(mci) shouldn't happen at the kobj.release, as it happens
when edac_remove_sysfs_mci_device() is called, but the logic is:
edac_remove_sysfs_mci_device(mci);
edac_printk(KERN_INFO, EDAC_MC,
"Removed device %d for %s %s: DEV %s\n", mci->mc_idx,
mci->mod_name, mci->ctl_name, edac_dev_name(mci));
So, as the edac_printk() needs the mci struct, this generates an OOPS.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A very nasty bug were happening on edac core, due to the way mci objects are
freed. mci memory is freed when kobject count reaches zero, by
edac_mci_control_release(). However, from the logs, this is clearly happening
before the final usage of mci struct:
[15799.607454] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 640: edac_mci_control_release() mci instance idx=0 releasing
[15799.618773] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 769: edac_inst_grp_release()
[15799.627326] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 894: edac_remove_mci_instance_attributes() end of seeking for group all_channel_counts
[15799.640887] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 877: edac_remove_mci_instance_attributes() sysfs_attrib = ffffffffa01d7240
[15799.653412] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 1020: edac_remove_sysfs_mci_device() remove_link
[15799.663753] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 1024: edac_remove_sysfs_mci_device() remove_mci_instance
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are two groups of sysfs attributes: one for rdimm and another
for udimm. Instead of changing dynamically the unique static struct
for handling udimm's, declare two vars and make them constant.
This avoids the risk of having two or more memory controllers, each
needing a different set of attributes.
While here, use const on all places where it is applicable.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
edac_core: use const for constant sysfs arguments
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With multi-sockets, more than one edac pci handler is enabled. Be sure to
un-register all instances.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'x86-amd-nb-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, amd_nb: Enable GART support for AMD family 0x15 CPUs
x86, amd: Use compute unit information to determine thread siblings
x86, amd: Extract compute unit information for AMD CPUs
x86, amd: Add support for CPUID topology extension of AMD CPUs
x86, nmi: Support NMI watchdog on newer AMD CPU families
x86, mtrr: Assume SYS_CFG[Tom2ForceMemTypeWB] exists on all future AMD CPUs
x86, k8: Rename k8.[ch] to amd_nb.[ch] and CONFIG_K8_NB to CONFIG_AMD_NB
x86, k8-gart: Decouple handling of garts and northbridges
x86, cacheinfo: Fix dependency of AMD L3 CID
x86, kvm: add new AMD SVM feature bits
x86, cpu: Fix allowed CPUID bits for KVM guests
x86, cpu: Update AMD CPUID feature bits
x86, cpu: Fix renamed, not-yet-shipping AMD CPUID feature bit
x86, AMD: Remove needless CPU family check (for L3 cache info)
x86, tsc: Remove CPU frequency calibration on AMD
Fix
drivers/edac/mce_amd.c:262: warning: left shift count >= width of type
on 32-bit builds.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
F11h has almost the same MCE signatures as K8 except DRAM ECC and MC5
bank errors. Reuse functionality from the other families.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Now that all decoders have been taught about F14h, models < 0x10
MCEs, enable decoding on this family of CPUs. Also, issue a short
informational message upon boot that MCE decoding gets enabled.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
F14h CPUs do not generate LS MCEs so exit early and warn the user in
case this path is ever hit that something else might be going haywire.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add support for IC MCEs for F14h CPUs. K8 and F10h are almost identical
so use one function for both.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add a per-family data cache decoders. Since there is a certain overlap
between the different DC MCE signatures, reuse functionality between the
families as far as possible.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Drop "edac_" string from the filenames since they're prefixed with edac/
in their pathname anyway.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add sysfs injection facilities for testing of the MCE decoding code.
Remove large parts of amd64_edac_dbg.c, as a result, which did only
NB MCE injection anyway and the new injection code supports that
functionality already.
Add an injection module so that MCE decoding code in production kernels
like those in RHEL and SLES can be tested.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Move toplevel sysfs class to the stub and make it available to
non-modularized code too. Add proper refcounting of its users and move
the registration functionality into the reference counting routines.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
... instead of the MCi_STATUS info only for improved handling of certain
types of errors later.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
.. so that the user knows what she's looking at there in dmesg. Also,
fix a minor cosmetic output inconsistency.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
f4347553b3 removed the edac polling
mechanism in favor of using a notifier chain for conveying MCE
information to edac. However, the module removal path didn't test
whether the driver had setup the polling function workqueue at all and
the rmmod process was hanging in the kernel at try_to_del_timer_sync()
in the cancel_delayed_work() path, trying to cancel an uninitialized
work struct.
Fix that by adding a balancing check to the workqueue removal path.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Due to the current edac-core limits, we cannot represent a per-channel
memory size, for FB-DIMM drivers. So, we need to sum-up all values
for each slot, in order to properly represent the total amount of
memory found by the i7300 driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is still somewhat fake, as the pages may not be on this exact order,
and may even be used in mirror mode, but this is a best guess than the
other random fake values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The file names are somehow misleading as the code is not specific to
AMD K8 CPUs anymore. The files accomodate code for other AMD CPU
northbridges as well.
Same is true for the config option which is valid for AMD CPU
northbridges in general and not specific to K8.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20100917160343.GD4958@loge.amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
So far we only provide num_k8_northbridges. This is required in
different areas (e.g. L3 cache index disable, GART). But not all AMD
CPUs provide a GART. Thus it is useful to split off the GART handling
from the generic caching of AMD northbridge misc devices.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20100917160254.GC4958@loge.amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This is basically a cleanup patch, improving the comments for each
function.
While here, do a few cleanups.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change should do no functional change. It just rearranges the
contents of the c file, in order to make easier to understand and
maintain it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of dynamically allocating a buffer for it where needed,
just allocate it once. As we'll use the same buffer also during
fatal and non-fatal errors, is is very risky to dynamically allocate
it during an error.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the error logic in this driver came from i5400 driver, it
were using one function to get errors, and another to display.
Let's make it simpler and avoid doing it into two steps.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's no mention at the datasheet about how to enable global error
reporting. So, I'm assuming that those errors are always enabled.
Maybe I'm plain wrong about that ;)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the Overflow MCi_STATUS bit is set, EDAC reports the lost error
with a "no information available" message which often puzzles users
parsing the dmesg. This doesn't make much sense since this error has
been lost anyway so no need for reporting it separately. Thus, report
the overflow bit setting in the MCE dump instead. While at it, remove
reporting of MiscV and ErrorEnable (en) which are superfluous.
Now it looks like this:
[ 1501.650024] MC4_STATUS: Corrected error, other errors lost: yes, CPU context corrupt: no, CECC Error
[ 1501.666887] Northbridge Error, node 2
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
