In some configurations, the BAM DMA controller is set up by a remote
processor and the local processor can simply start making use of it
without setting up the BAM. This is already supported using the
"qcom,controlled-remotely" property.
However, for some reason another possible configuration is that the
remote processor is responsible for powering up the BAM, but we are
still responsible for initializing it (e.g. resetting it etc).
This configuration is quite challenging to handle properly because
the power control is handled through separate channels
(e.g. device-specific SMSM interrupts / smem-states). Great care
must be taken to ensure the BAM registers are not accessed while
the BAM is powered off since this results in a bus stall.
Attempt to support this configuration with minimal device-specific
code in the bam_dma driver by tracking the number of requested
channels. Consumers of DMA channels are responsible to only request
DMA channels when the BAM was powered on by the remote processor,
and to release them before the BAM is powered off.
When the first channel is requested the BAM is initialized (reset)
and it is also put into reset when the last channel was released.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20211018102421.19848-3-stephan@gerhold.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When bam dma is "controlled remotely", thus far clocks were not controlled
from the Linux. In this scenario, Linux was disabling runtime pm in bam dma
driver and not doing any clock management in suspend/resume hooks.
With introduction of crypto engine bam dma, the clock is a rpmh resource
that can be controlled from both Linux and TZ/remote side. Now bam dma
clock is getting enabled during probe even though the bam dma can be
"controlled remotely". But due to clocks not being handled properly,
bam_suspend generates a unbalanced clk_unprepare warning during system
suspend.
To fix the above issue and to enable proper clock-management, this patch
enables runtim-pm and handles bam dma clocks in suspend/resume hooks if
the clock node is present irrespective of controlled_remotely property.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210126211859.790892-1-thara.gopinath@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The parameter of kfree function is NULL, so kfree code is useless, delete it.
Therefore, goto expression is no longer needed, so simplify it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201216130649.13979-1-zhengyongjun3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While performing suspend/resume, we were getting below kernel crash.
[ 54.541672] [FTS][Info]gesture suspend...
[ 54.605256] [FTS][Error][GESTURE]Enter into gesture(suspend) failed!
[ 54.605256]
[ 58.345850] irq event 10: bogus return value fffffff3
......
[ 58.345966] [<ffff0000080830f0>] el1_irq+0xb0/0x124
[ 58.345971] [<ffff000008085360>] arch_cpu_idle+0x10/0x18
[ 58.345975] [<ffff0000081077f4>] do_idle+0x1ac/0x1e0
[ 58.345979] [<ffff0000081079c8>] cpu_startup_entry+0x20/0x28
[ 58.345983] [<ffff000008a80ed0>] rest_init+0xd0/0xdc
[ 58.345988] [<ffff0000091c0b48>] start_kernel+0x390/0x3a4
[ 58.345990] handlers:
[ 58.345994] [<ffff0000085120d0>] bam_dma_irq
The reason for the crash we found is, bam_dma_irq() was returning
negative value when the device resumes in some conditions.
In addition, the irq handler should have one of the below return values.
IRQ_NONE interrupt was not from this device or was not handled
IRQ_HANDLED interrupt was handled by this device
IRQ_WAKE_THREAD handler requests to wake the handler thread
Therefore, to resolve this crash, we have changed the return value to
IRQ_NONE.
Signed-off-by: Parth Y Shah <sparth1292@gmail.com>
Link: https://lore.kernel.org/r/1607322820-7450-1-git-send-email-sparth1292@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 00c4747a2f ("dmaengine: qcom: convert tasklets to use new
tasklet_setup() API") updated driver to use new tasklet_setup() API but
missed to update the documentation for the tasklet function.
Fixes: 00c4747a2f ("dmaengine: qcom: convert tasklets to use new tasklet_setup() API")
Link: https://lore.kernel.org/r/20201007083113.567559-3-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-23-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200508210707.GA24136@embeddedor
Signed-off-by: Vinod Koul <vkoul@kernel.org>
bam_dma_terminate_all() will leak resources if any of the transactions are
committed to the hardware (present in the desc fifo), and not complete.
Since bam_dma_terminate_all() does not cause the hardware to be updated,
the hardware will still operate on any previously committed transactions.
This can cause memory corruption if the memory for the transaction has been
reassigned, and will cause a sync issue between the BAM and its client(s).
Fix this by properly updating the hardware in bam_dma_terminate_all().
Fixes: e7c0fe2a5c ("dmaengine: add Qualcomm BAM dma driver")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191017152606.34120-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
One space is left unused in circular FIFO to differentiate
'full' and 'empty' cases. So take that in to account while
counting for the descriptors completed.
Fixes the issue reported here,
https://lkml.org/lkml/2019/6/18/669
Cc: stable@vger.kernel.org
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- Updates to sprd, bam_dma, stm drivers.
- removal of VLAs in dmatest.
- Move TI drivers its own subdir.
- Switch to SPDX tags for ima/mxs dma drivers.
- Simplify getting .drvdata on bunch of drivers by Wolfram Sang.
-----BEGIN PGP SIGNATURE-----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=8mGV
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.18-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- updates to sprd, bam_dma, stm drivers
- remove VLAs in dmatest
- move TI drivers to their own subdir
- switch to SPDX tags for ima/mxs dma drivers
- simplify getting .drvdata on bunch of drivers by Wolfram Sang
* tag 'dmaengine-4.18-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (32 commits)
dmaengine: sprd: Add Spreadtrum DMA configuration
dmaengine: sprd: Optimize the sprd_dma_prep_dma_memcpy()
dmaengine: imx-dma: Switch to SPDX identifier
dmaengine: mxs-dma: Switch to SPDX identifier
dmaengine: imx-sdma: Switch to SPDX identifier
dmaengine: usb-dmac: Document R8A7799{0,5} bindings
dmaengine: qcom: bam_dma: fix some doc warnings.
dmaengine: qcom: bam_dma: fix invalid assignment warning
dmaengine: sprd: fix an NULL vs IS_ERR() bug
dmaengine: sprd: Use devm_ioremap_resource() to map memory
dmaengine: sprd: Fix potential NULL dereference in sprd_dma_probe()
dmaengine: pl330: flush before wait, and add dev burst support.
dmaengine: axi-dmac: Request IRQ with IRQF_SHARED
dmaengine: stm32-mdma: fix spelling mistake: "avalaible" -> "available"
dmaengine: rcar-dmac: Document R-Car D3 bindings
dmaengine: sprd: Move DMA request mode and interrupt type into head file
dmaengine: sprd: Define the DMA data width type
dmaengine: sprd: Define the DMA transfer step type
dmaengine: ti: New directory for Texas Instruments DMA drivers
dmaengine: shdmac: Change platform check to CONFIG_ARCH_RENESAS
...
Building kernel with W=1 throws up below warnings:
bam_dma.c:459: warning: Function parameter or member 'dir'
not described in 'bam_chan_init_hw'
bam_dma.c:697: warning: Function parameter or member 'chan'
not described in 'bam_dma_terminate_all'
bam_dma.c:697: warning: Excess function parameter 'bchan'
description in 'bam_dma_terminate_all'
bam_dma.c:964: warning: Function parameter or member 'bchan'
not described in 'bam_start_dma'
Fix these!.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Building kernel with W=1 throws below invalid assignment warnings.
bam_dma.c:676:44: warning: invalid assignment: +=
bam_dma.c:676:44: left side has type unsigned long
bam_dma.c:676:44: right side has type restricted __le16
bam_dma.c:921:41: warning: invalid assignment: +=
bam_dma.c:921:41: left side has type unsigned long
bam_dma.c:921:41: right side has type restricted __le16
Fix them!.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Disabling pm runtime at probe is not sufficient to get BAM working
on remotely controller instances. pm_runtime_get_sync() would return
-EACCES in such cases.
So check if runtime pm is enabled before returning error from bam functions.
Fixes: 5b4a68952a ("dmaengine: qcom: bam_dma: disable runtime pm on remote controlled")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remotely controlled BAM instance should not do any power management from
CPU side, as cpu can not reliably say if the BAM is busy or not.
Disable it for such instances.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
BAM_DESC_CNT_TRSHLD register is global register, which can only be written
when BAM is in master mode, So check the mode of operation before writing
it.
Without this check SOC's xPU would catch such access and crash the system.
First noticed on DB820c while testing SLIMBus BAM.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When Linux is master of BAM, it can directly read registers to know number
of supported channels, however when its remotely controlled reading these
registers would trigger a crash if the BAM is not yet initialized or
powered up on the remote side.
This patch allows driver to read num-channels and num-ees from Device Tree
for remotely controlled BAM.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When BAM is remotely controlled it does not sound correct to control
its clk on Linux side. Make it optional, so that its not mandatory
for remote controlled BAM instances.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The bam dmaengine has a circular FIFO to which we
add hw descriptors that describes the transaction.
The FIFO has space for about 4096 hw descriptors.
Currently we add one descriptor and wait for it to
complete with interrupt and then add the next pending
descriptor. In this way, the FIFO is underutilized
since only one descriptor is processed at a time, although
there is space in FIFO for the BAM to process more.
Instead keep adding descriptors to FIFO till its full,
that allows BAM to continue to work on the next descriptor
immediately after signalling completion interrupt for the
previous descriptor.
Also when the client has not set the DMA_PREP_INTERRUPT for
a descriptor, then do not configure BAM to trigger a interrupt
upon completion of that descriptor. This way we get a interrupt
only for the descriptor for which DMA_PREP_INTERRUPT was
requested and there signal completion of all the previous completed
descriptors. So we still do callbacks for all requested descriptors,
but just that the number of interrupts are reduced.
CURRENT:
------ ------- ---------------
|DES 0| |DESC 1| |DESC 2 + INT |
------ ------- ---------------
| | |
| | |
INTERRUPT: (INT) (INT) (INT)
CALLBACK: (CB) (CB) (CB)
MTD_SPEEDTEST READ PAGE: 3560 KiB/s
MTD_SPEEDTEST WRITE PAGE: 2664 KiB/s
IOZONE READ: 2456 KB/s
IOZONE WRITE: 1230 KB/s
bam dma interrupts (after tests): 96508
CHANGE:
------ ------- -------------
|DES 0| |DESC 1 |DESC 2 + INT |
------ ------- --------------
|
|
(INT)
(CB for 0, 1, 2)
MTD_SPEEDTEST READ PAGE: 3860 KiB/s
MTD_SPEEDTEST WRITE PAGE: 2837 KiB/s
IOZONE READ: 2677 KB/s
IOZONE WRITE: 1308 KB/s
bam dma interrupts (after tests): 58806
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If DMA_PREP_CMD flag is passed in prep_slave_sg then peripheral
driver has passed the data is in BAM command descriptor format
and BAM driver should set CMD bit for each of the HW descriptors.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The bam_dma driver gained runtime PM support, but that causes build
warnings whenever CONFIG_PM is disabled:
drivers/dma/qcom/bam_dma.c:1324:12: error: 'bam_dma_runtime_resume' defined but not used [-Werror=unused-function]
static int bam_dma_runtime_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~~
drivers/dma/qcom/bam_dma.c:1315:12: error: 'bam_dma_runtime_suspend' defined but not used [-Werror=unused-function]
static int bam_dma_runtime_suspend(struct device *dev)
This removes the incomplete #ifdef guard and instead marks all
four PM functions as __maybe_unused, which avoids this kind of
warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7d2545599f ("dmaengine: qcom-bam-dma: Add pm_runtime support")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Adds pm_runtime support for BAM DMA so that clock is enabled only
when there is a transaction going on to help save power.
Signed-off-by: Pramod Gurav <pramod.gurav@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It seems that the define has not been with acurate name and
makes confusion while reading the code. The more acurate
name should be BAM_FIFO_SIZE.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pipe fifo size register must instruct the bam hw
how many hw descriptors can be pushed to fifo. Currently
we instruct the hw with 32KBytes but wrap the tail in
bam_start_dma in BAM_P_EVNT_REG on 4095 i.e. 32760. This
leads to stalled transactions when the tail wraps.
Fix this by use the correct fifo size in BAM_P_FIFO_SIZES
register i.e. 32K - 8.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some of the peripherals has bam which is controlled by remote
processor, thus the bam dma driver must avoid register writes
which initialise bam hw block. Those registers are protected
from xPU block and any writes to them will lead to secure
violation and system reboot.
Adding the contolled_remotely flag in bam driver to avoid
not permitted register writes in bam_init function.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Pramod Gurav <gpramod@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently we write BAM_IRQ_CLR register with zero even when no
BAM_IRQ occured. This write has some bad side effects when the
BAM instance is for the crypto engine. In case of crypto engine
some of the BAM registers are xPU protected and they cannot be
controlled by the driver.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Pramod Gurav <gpramod@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is smallish update with minor changes to core and new driver and usual
updates. Nothing super exciting here..
- We have made slave address as physical to enable driver to do the mapping.
- We now expose the maxburst for slave dma as new capability so clients can
know this and program accordingly
- addition of device synchronize callbacks on omap and edma.
- pl330 updates to support DMAFLUSHP for Rockchip platforms.
- Updates and improved sg handling in Xilinx VDMA driver.
- New hidma qualcomm dma driver, though some bits are still in progress
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wCCJ
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This is smallish update with minor changes to core and new driver and
usual updates. Nothing super exciting here..
- We have made slave address as physical to enable driver to do the
mapping.
- We now expose the maxburst for slave dma as new capability so
clients can know this and program accordingly
- addition of device synchronize callbacks on omap and edma.
- pl330 updates to support DMAFLUSHP for Rockchip platforms.
- Updates and improved sg handling in Xilinx VDMA driver.
- New hidma qualcomm dma driver, though some bits are still in
progress"
* tag 'dmaengine-4.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (40 commits)
dmaengine: IOATDMA: revise channel reset workaround on CB3.3 platforms
dmaengine: add Qualcomm Technologies HIDMA channel driver
dmaengine: add Qualcomm Technologies HIDMA management driver
dmaengine: hidma: Add Device Tree binding
dmaengine: qcom_bam_dma: move to qcom directory
dmaengine: tegra: Move of_device_id table near to its user
dmaengine: xilinx_vdma: Remove unnecessary variable initializations
dmaengine: sirf: use __maybe_unused to hide pm functions
dmaengine: rcar-dmac: clear pertinence number of channels
dmaengine: sh: shdmac: don't open code of_device_get_match_data()
dmaengine: tegra: don't open code of_device_get_match_data()
dmaengine: qcom_bam_dma: Make driver work for BE
dmaengine: sun4i: support module autoloading
dma/mic_x100_dma: IS_ERR() vs PTR_ERR() typo
dmaengine: xilinx_vdma: Use readl_poll_timeout instead of do while loop's
dmaengine: xilinx_vdma: Simplify spin lock handling
dmaengine: xilinx_vdma: Fix issues with non-parking mode
dmaengine: xilinx_vdma: Improve SG engine handling
dmaengine: pl330: fix to support the burst mode
dmaengine: make slave address physical
...
Creating a QCOM directory for all QCOM DMA source files.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
