There's an issue on SAI synchronous mode that TX/RX side can't get BCLK
from RX/TX it sync with if BYP bit is asserted. It's a workaround to
fix it that enable SION of IOMUX pad control and assert BCI.
For example if TX sync with RX which means both TX and RX are using clk
form RX and BYP=1. TX can get BCLK only if the following two conditions
are valid:
1. SION of RX BCLK IOMUX pad is set to 1
2. BCI of TX is set to 1
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230530103012.3448838-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The code in asoc_simple_startup was treating any non-zero return from
snd_pcm_hw_constraint_minmax as an error, when this can return 1 in some
normal cases and only negative values indicate an error.
When this happened, it caused asoc_simple_startup to disable the clocks
it just enabled and return 1, which was not treated as an error by the
calling code which only checks for negative return values. Then when the
PCM is eventually shut down, it causes the clock framework to complain
about disabling clocks that were not enabled.
Fix the check for snd_pcm_hw_constraint_minmax return value to only
treat negative values as an error.
Fixes: 5ca2ab4598 ("ASoC: simple-card-utils: Add new system-clock-fixed flag")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20230602011936.231931-1-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Trevor Wu <trevor.wu@mediatek.com>:
These patches concern modifications made in mt8186[1]. The clock
unregistration mechanism used in mt8188 and mt8195 is similar with
mt8186, resulting in the same problem existing within the driver.
Therefore, the solution has also been applied to these two platforms.
[1] https://lore.kernel.org/all/20230511092437.1.I31cceffc8c45bb1af16eb613e197b3df92cdc19e@changeid/
The dma pointer must be set to the passed stream pointer, even
if that pointer is NULL.
Fixes: e496112529 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230601124907.3128170-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
MAX98363 does not support 32bit depth audio.
Removed 32bit from the supported format list.
Instead, added 16bit and 24bit to the list.
Signed-off-by: Ryan Lee <ryans.lee@analog.com>
Link: https://lore.kernel.org/r/20230601130600.25344-1-ryan.lee.analog@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During mt8195_afe_init_clock(), mt8195_audsys_clk_register() was called
followed by several other devm functions. At mt8195_afe_deinit_clock()
located at mt8195_afe_pcm_dev_remove(), mt8195_audsys_clk_unregister()
was called.
However, there was an issue with the order in which these functions were
called. Specifically, the remove callback of platform_driver was called
before devres released the resource, resulting in a use-after-free issue
during remove time.
At probe time, the order of calls was:
1. mt8195_audsys_clk_register
2. afe_priv->clk = devm_kcalloc
3. afe_priv->clk[i] = devm_clk_get
At remove time, the order of calls was:
1. mt8195_audsys_clk_unregister
3. free afe_priv->clk[i]
2. free afe_priv->clk
To resolve the problem, we can utilize devm_add_action_or_reset() in
mt8195_audsys_clk_register() so that the remove order can be changed to
3->2->1.
Fixes: 6746cc8582 ("ASoC: mediatek: mt8195: add platform driver")
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230601033318.10408-3-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During mt8188_afe_init_clock(), mt8188_audsys_clk_register() was called
followed by several other devm functions. The caller of
mt8188_afe_init_clock() utilized devm_add_action_or_reset() to call
mt8188_afe_deinit_clock(). However, the order was incorrect, causing a
use-after-free issue during remove time.
At probe time, the order of calls was:
1. mt8188_audsys_clk_register
2. afe_priv->clk = devm_kcalloc
3. afe_priv->clk[i] = devm_clk_get
At remove time, the order of calls was:
1. mt8188_audsys_clk_unregister
3. free afe_priv->clk[i]
2. free afe_priv->clk
To resolve the problem, it's necessary to move devm_add_action_or_reset()
to the appropriate position so that the remove order can be 3->2->1.
Fixes: f6b026479b ("ASoC: mediatek: mt8188: support audio clock control")
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230601033318.10408-2-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Thinkpad Neo14 Ryzen Edition uses Ryzen 6800H processor, and adding to
quirks list for acp6x will enable internal mic.
Signed-off-by: Sicong Jiang <kevin.jiangsc@gmail.com>
Link: https://lore.kernel.org/r/20230531090635.89565-1-kevin.jiangsc@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add entries for Positivo laptops: CW14Q01P, K1424G, N14ZP74G to the
DMI table, so that active-high jack-detect will work properly on
these laptops.
Signed-off-by: Edson Juliano Drosdeck <edson.drosdeck@gmail.com>
Link: https://lore.kernel.org/r/20230529181911.632851-1-edson.drosdeck@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sending the mutex address(acp_lock) as platform
data during ACP PDM platform driver register sequence,
its creating copy of the platform data.
Referencing this platform data in ACP PDM driver results
incorrect reference to the common lock usage.
Instead of directly passing the lock address as platform
data, retrieve it from parent driver data structure
and use the same lock reference in ACP PDM driver.
Fixes: 45aa83cb93 ("ASoC: amd: ps: use acp_lock to protect common registers in pdm driver")
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230525113000.1290758-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the error path, a of_node_put() for platform is missing.
Just add it.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20230523151223.109551-9-herve.codina@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap-sdw does not support multi register writes, so there is
no point in setting this flag. This also leads to incorrect
programming of WSA codecs with regmap_multi_reg_write() call.
This invalid configuration should have been rejected by regmap-sdw.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230523165414.14560-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap-sdw does not support multi register writes, so there is
no point in setting this flag. This also leads to incorrect
programming of WSA codecs with regmap_multi_reg_write() call.
This invalid configuration should have been rejected by regmap-sdw.
Fixes: a0aab9e140 ("ASoC: codecs: add wsa881x amplifier support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230523154605.4284-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap-sdw does not support multi register writes, so there is
no point in setting this flag. This also leads to incorrect
programming of WSA codecs with regmap_multi_reg_write() call.
This invalid configuration should have been rejected by regmap-sdw.
Fixes: 43b8c7dc85 ("ASoC: codecs: add wsa883x amplifier support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230523154605.4284-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Constraint functions have return values, they should be checked for
potential errors.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-8-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All IPCs using instance_id use 8 bit value. Original commit used 16 bit
value because FW reports possible max value in 16 bit field, but in
practice FW limits the value to 8 bits.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-7-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Configurations with multiple codecs attached to the platform are
supported but only if each from the set is different. Add new field
representing the 'Unique ID' so that codecs that share Vendor and Part
IDs can be differentiated and thus enabling support for such
configurations.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-6-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Constant 'C4_CHANNEL' does not exist on the firmware side. Value 0xC is
reserved for 'C7_1' instead.
Fixes: 580a5912d1 ("ASoC: Intel: avs: Declare module configuration types")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-5-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Path and its components should be accessed under lock to prevent
problems with one thread modifying them while other tries to read.
Fixes: c8c960c109 ("ASoC: Intel: avs: APL-based platforms support")
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-3-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When changing value of kcontrol, FW module to which data should be send
needs to be found. Currently it is done in improper way, fix it. Change
function name to indicate that it looks only for volume module.
This allows to change volume during runtime, instead of only changing
init value.
Fixes: be2b81b519 ("ASoC: Intel: avs: Parse control tuples")
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-2-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the BE hw_params configuration, the existing code checks if any of the
existing FEs are prepared, running, paused or suspended - and skips the
configuration in those cases. This allows multiple calls of hw_params
which the ALSA state machine supports.
This check is not handled for the prepare stage, which can lead to the
same BE being prepared multiple times. This patch adds a check similar to
that of the hw_params, with the main difference being that the suspended
state is allowed: the ALSA state machine allows a transition from
suspended to prepared with hw_params skipped.
This problem was detected on Intel IPC4/SoundWire devices, where the BE
dailink .prepare stage is used to configure the SoundWire stream with a
bank switch. Multiple .prepare calls lead to conflicts with the .trigger
operation with IPC4 configurations. This problem was not detected earlier
on Intel devices, HDaudio BE dailinks detect that the link is already
prepared and skip the configuration, and for IPC3 devices there is no BE
trigger.
Link: https://github.com/thesofproject/sof/issues/7596
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230517185731.487124-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
The rt5682 driver switches its regmap to cache-only when the
device suspends and back to regular mode on resume. When the
jack detect interrupt fires rt5682_irq() schedules the jack
detect work. This can result in invalid reads from the regmap
in cache-only mode if the work runs before the device has
resumed:
[ 56.245502] rt5682 9-001a: ASoC: error at soc_component_read_no_lock on rt5682.9-001a for register: [0x000000f0] -16
Disable the jack detection interrupt during suspend and
re-enable it on resume. The driver already schedules the
jack detection work on resume, so any state change during
suspend is still handled.
This is essentially the same as commit f7d00a9be1 ("SoC:
rt5682s: Disable jack detection interrupt during suspend")
for the rt5682s.
Cc: stable@kernel.org
Signed-off-by: Matthias Kaehlcke <mka@chromium.org
Reviewed-by: Douglas Anderson <dianders@chromium.org
Reviewed-by: Stephen Boyd <swboyd@chromium.org
Link: https://lore.kernel.org/r/20230516164629.1.Ibf79e94b3442eecc0054d2b478779cc512d967fc@changeid
Signed-off-by: Mark Brown <broonie@kernel.org
When we run syzkaller we get below Out of Bounds error.
"KASAN: slab-out-of-bounds Read in regcache_flat_read"
Below is the backtrace of the issue:
BUG: KASAN: slab-out-of-bounds in regcache_flat_read+0x10c/0x110
Read of size 4 at addr ffffff8088fbf714 by task syz-executor.4/14144
CPU: 6 PID: 14144 Comm: syz-executor.4 Tainted: G W
Hardware name: Qualcomm Technologies, Inc. sc7280 CRD platform (rev5+) (DT)
Call trace:
dump_backtrace+0x0/0x4ec
show_stack+0x34/0x50
dump_stack_lvl+0xdc/0x11c
print_address_description+0x30/0x2d8
kasan_report+0x178/0x1e4
__asan_report_load4_noabort+0x44/0x50
regcache_flat_read+0x10c/0x110
regcache_read+0xf8/0x5a0
_regmap_read+0x45c/0x86c
_regmap_update_bits+0x128/0x290
regmap_update_bits_base+0xc0/0x15c
snd_soc_component_update_bits+0xa8/0x22c
snd_soc_component_write_field+0x68/0xd4
tx_macro_put_dec_enum+0x1d0/0x268
snd_ctl_elem_write+0x288/0x474
By Error checking and checking valid values issue gets rectifies.
Signed-off-by: Ravulapati Vishnu Vardhan Rao <quic_visr@quicinc.com
Link: https://lore.kernel.org/r/20230511112532.16106-1-quic_visr@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
With additional testing with multiple links and multiple DAI types, we
found a couple of mistakes with refcounts, base address, missing
initialization.
A new helper was also added due to a change in the SoundWire
programming sequences, with the host driver in charge of setting up
the DMA channel mapping instead of the firmware.
The memory allocated for the tuples array assumes that there's 1
instance of all tokens already. So for those tokens that have multiple
instances in topology, we need to exclude the initial instance that has
already been accounted for.
Fixes: 4fdef47a44 ("ASoC: SOF: ipc4-topology: Add new tokens for input/output pin format count")
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230515085200.17094-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
Using the same token ID for both input and output format pin index
results in collisions and incorrect pin index getting parsed from
topology.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230515104403.32207-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
Flush the SoundWire interrupt handler work instead of cancelling it.
When a SoundWire interrupt is triggered the pm_runtime is held
until the work has completed. It's therefore unsafe to cancel
the work, it must be flushed.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230512144237.739000-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org
Topology could have more instances of the tokens being searched for than
the number of sets that need to be copied. Stop copying token after the
limit of number of token instances has been reached. This worked before
only by chance as we had allocated more size for the tuples array than
the number of actual tokens being parsed.
Fixes: 7006d20e5e ("ASoC: SOF: Introduce IPC3 ops")
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230512114630.24439-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
If there are failures in DSP runtime resume, the device state will not
reach active and this makes it impossible e.g. to retrieve a possible
DSP panic dump via "exception" debugfs node. If
CONFIG_SND_SOC_SOF_DEBUG_ENABLE_DEBUGFS_CACHE=y is set, the data in
cache is stale. If debugfs cache is not used, the region simply cannot
be read.
To allow debugging these scenarios, update the debugfs cache contents in
resume error handler. User-space can then later retrieve DSP panic and
other state via debugfs (requires SOF debugfs cache to be enabled in
build).
Reported-by: Curtis Malainey <cujomalainey@chromium.org
Link: https://github.com/thesofproject/linux/issues/4274
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Curtis Malainey <cujomalainey@chromium.org
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230512104638.21376-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
When devm runs function in the "remove" path for a device it runs them
in the reverse order. That means that if you have parts of your driver
that aren't using devm or are using "roll your own" devm w/
devm_add_action_or_reset() you need to keep that in mind.
The mt8186 audio driver didn't quite get this right. Specifically, in
mt8186_init_clock() it called mt8186_audsys_clk_register() and then
went on to call a bunch of other devm function. The caller of
mt8186_init_clock() used devm_add_action_or_reset() to call
mt8186_deinit_clock() but, because of the intervening devm functions,
the order was wrong.
Specifically at probe time, the order was:
1. mt8186_audsys_clk_register()
2. afe_priv->clk = devm_kcalloc(...)
3. afe_priv->clk[i] = devm_clk_get(...)
At remove time, the order (which should have been 3, 2, 1) was:
1. mt8186_audsys_clk_unregister()
3. Free all of afe_priv->clk[i]
2. Free afe_priv->clk
The above seemed to be causing a use-after-free. Luckily, it's easy to
fix this by simply using devm more correctly. Let's move the
devm_add_action_or_reset() to the right place. In addition to fixing
the use-after-free, code inspection shows that this fixes a leak
(missing call to mt8186_audsys_clk_unregister()) that would have
happened if any of the syscon_regmap_lookup_by_phandle() calls in
mt8186_init_clock() had failed.
Fixes: 55b423d562 ("ASoC: mediatek: mt8186: support audio clock control in platform driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org
Link: https://lore.kernel.org/r/20230511092437.1.I31cceffc8c45bb1af16eb613e197b3df92cdc19e@changeid
Signed-off-by: Mark Brown <broonie@kernel.org
The commands in sof_ipc_dai_config.flags are encoded as bits:
1 (bit0) - hw_params
2 (bit1) - hw_free
4 (bit2) - pause
These are commands, they cannot be combined as one would assume, for
example
3 (bit0 | bit1) is invalid.
This can happen right at the second start of a stream as at the end of the
first stream we set the hw_free command (bit1) and on the second start we
would OR on top of it the hw_params (bit0).
Fixes: b66bfc3a98 ("ASoC: SOF: sof-audio: Fix broken early bclk feature for SSP")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230512110317.5180-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
When an error occurs, we need to make sure the device can pm_runtime
suspend instead of keeping it active.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230512103315.8921-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
When an error occurs, we need to make sure the device can pm_runtime
suspend instead of keeping it active.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230512103315.8921-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
When a firmware IPC error happens during a pm_runtime suspend, we
ignore the error and suspend anyways. However, the code
unconditionally increases the runtime_pm counter. This results in a
confusing configuration where the code will suspend, resume but never
suspend again due to the use of pm_runtime_get_noresume().
The intent of the counter increase was to prevent entry in D3, but if
that transition to D3 is already started it cannot be stopped. In
addition, there's no point in that case in trying to prevent anything,
the firmware error is handled and the next resume will re-initialize
the firmware completely.
This patch changes the logic to prevent suspend when the device is
pm_runtime active and has a use_count > 0.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230512103315.8921-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
These registers enable the HDaudio DMA hardware to split/merge data
from different PDIs, possibly on different links.
This capability exists for all types of HDaudio extended links, but
for now is only required for SoundWire. In the SSP/DMIC case, the IP
is programmed by the DSP firmware.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Rander Wang <rander.wang@intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
We defined the values but never initialized it for SoundWire/SSP, fix
this miss.
A Fixes: tag is not provided as instance_offset was not used so far,
so nothing was really broken. This patch is only required for the
SoundWire support in the following patch.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Rander Wang <rander.wang@intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
We mix the use of hlink->ml_addr and the 'ml_addr' parameter. It's the
same thing, let's align on using the parameter.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Rander Wang <rander.wang@intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
The base_ptr value needs to be derived from the remap_addr pointer,
not the ml_addr. This base_ptr was used only in debug logs that were
so far not contributed upstream so the issue was not detected. It
needs to be fixed for SoundWire support on LunarLake.
Fixes: 17c9b6ec35 ("ASoC: SOF: Intel: hda-mlink: add structures to parse ALT links")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Rander Wang <rander.wang@intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
Same functionality as for DMIC/SSP with different ID.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Rander Wang <rander.wang@intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
In hindsight it was a very bad idea to use the same refcount for
Extended and 'legacy' HDaudio multi-links. The existing solution only
powers-up the first sublink, which causes SoundWire and SSP tests to
fail when more than one DAI is used concurrently. Solving this problem
requires per-sublink refcounting, as suggested in this patch.
The existing refcounting remains for 'legacy' HdAudio links, mainly to
avoid changing the obscure programming sequence in
snd_hdac_ext_bus_link_put().
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
Apply a workaround for what appears to be a hardware quirk.
The problem seems to happen when enabling "whole chip power" (bit D7
register R6) for the very first time after the chip receives power. If
either "output" (D4) or "DAC" (D3) aren't powered on at that time,
playback becomes very distorted later on.
This happens on the Google Chameleon v3, as well as on a ZYBO Z7-10:
https://ez.analog.com/audio/f/q-a/543726/solved-ssm2603-right-output-offset-issue/480229
I suspect this happens only when using an external MCLK signal (which
is the case for both of these boards).
Here are some experiments run on a Google Chameleon v3. These were run
in userspace using a wrapper around the i2cset utility:
ssmset() {
i2cset -y 0 0x1a $(($1*2)) $2
}
For each of the following sequences, we apply power to the ssm2603
chip, set the configuration registers R0-R5 and R7-R8, run the selected
sequence, and check for distortions on playback.
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # chip, out, dac
OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x87 # out, dac
ssmset 0x06 0x07 # chip
OK
(disable MCLK)
ssmset 0x09 0x01 # core
ssmset 0x06 0x1f # chip
ssmset 0x06 0x07 # out, dac
(enable MCLK)
OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x1f # chip
ssmset 0x06 0x07 # out, dac
NOT OK
ssmset 0x06 0x1f # chip
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # out, dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x0f # chip, out
ssmset 0x06 0x07 # dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x17 # chip, dac
ssmset 0x06 0x07 # out
NOT OK
For each of the following sequences, we apply power to the ssm2603
chip, run the selected sequence, issue a reset with R15, configure
R0-R5 and R7-R8, run one of the NOT OK sequences from above, and check
for distortions.
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # chip, out, dac
OK
(disable MCLK)
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # chip, out, dac
(enable MCLK after reset)
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x17 # chip, dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x0f # chip, out
NOT OK
ssmset 0x06 0x07 # chip, out, dac
NOT OK
Signed-off-by: Paweł Anikiel <pan@semihalf.com
Link: https://lore.kernel.org/r/20230508113037.137627-8-pan@semihalf.com
Signed-off-by: Mark Brown <broonie@kernel.org
When the CPU supplies bit/frame clocks, the system clock (clk_i2s)
is divided to produce the bit clock. This is a simple 1/N divider
with a fairly limited range, so for a given system clock frequency
only a few sample rates can be produced. Usually a wider range of
sample rates is supported by varying the system clock frequency.
The old calculation method was not very robust and could easily
produce the wrong clock rate, especially with non-standard rates.
For example, if the system clock is 1.99x the target bit clock
rate, the divider would be calculated as 1 instead of the more
accurate 2.
Instead, use a more accurate method that considers two adjacent
divider settings and selects the one that produces the least error
versus the requested rate. If the error is 5% or higher then the
rate setting is rejected to prevent garbled audio.
Skip divider calculation when the codec is supplying both the bit
and frame clock; in that case, the divider outputs are unused and
we don't want to constrain the sample rate.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com
Link: https://lore.kernel.org/r/20230509125134.208129-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org
There is error message when defer probe happens:
fsl-micfil-dai 30ca0000.micfil: Unbalanced pm_runtime_enable!
Fix the error handler with pm_runtime_enable and add
fsl_micfil_remove() for pm_runtime_disable.
Fixes: 47a70e6fc9 ("ASoC: Add MICFIL SoC Digital Audio Interface driver.")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com
Link: https://lore.kernel.org/r/1683540996-6136-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org
On slow CPU (FPGA/QEMU emulated) printing overrun messages from
interrupt handler to uart console may leads to more overrun errors.
So use dev_err_ratelimited to limit the number of error messages.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru
Link: https://lore.kernel.org/r/20230505062820.21840-1-fido_max@inbox.ru
Signed-off-by: Mark Brown <broonie@kernel.org
