Nothing outside of drivers/tty/tty_io.c references these functions, so
mark them static.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
C files should include the header files that prototype their functions.
This keeps the types in sync, and eliminates warnings from GCC
(-Wmissing-prototypes) and Sparse (-Wdecl).
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"Asynchronous" is misspelled in some comments. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Only we meet the following conditions, we can enable the DMA support for
auart:
(1) We enable the DMA support in the dts file, such as
arch/arm/boot/dts/imx28.dtsi.
(2) We enable the hardware flow control.
(3) We use the mx28, not the mx23. Due to hardware bug(see errata: 2836),
we can not add the DMA support to mx23.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current mxs-auart driver is used for both mx23 and mx28.
But in mx23, the DMA has a bug(see errata:2836). We can not add the
DMA support in mx23, but we can add DMA support to auart in mx28.
So in order to add the DMA support for the auart in mx28, we should
distinguish the distinguish SOCs.
This patch adds a new platform_device_id table and a inline function
is_imx28_auart() to distinguish the mx23 and mx28.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows overriding default methods serial_in/serial_out.
In such platform specific replacement it is possible to use
other regshift, biased register offset, any other manipulation
that is not covered with common default methods.
Overriding default methods may be useful for platforms which got
serial peripheral with registers represented in big endian.
In this situation and assuming that 32 bit operations / alignment
is required then it may be useful to swab words before/after
accessing the serial registers.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definitions provided by serial_at91.h are only used by the
atmel_serial driver, and the function that uses it is never called
from anywhere in the kernel. Therefore, these definitions are unused
and/or obsolete, and can be removed.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is really driver platform data, so move it to the appropriate
directory.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the previous commit, console write function (serial_console_write)
is changed to disable SCI interrupts while printing console strings.
This introduces possible race cases in the serial startup / shutdown
functions on SMP systems.
This patch fixes the sh-sci in the same way as commit 9ec1882df2
(tty: serial: imx: console write routing is unsafe on SMP, from
Xinyu Chen <xinyu.chen@freescale.com>, 2012-08-27) did.
There could be several consumers of the console,
* the kernel printk
* the init process using /dev/kmsg to call printk to show log
* shell, which opens /dev/console and writes with sys_write()
The shell goes into the normal UART open() and write() system calls,
while the other two go into the console operations. The open() call
invokes serial startup function (sci_startup), which will write to
the SCSCR register (to enable or disable SCI interrupts) without any
locking. This will conflict with the console serial function.
Add spinlock protections in sci_startup() and sci_shutdown() properly.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Symptom:
When entering the suspend with Android logcat running, printk() call
gets stuck and never returns. The issue can be observed at printk()s
on nonboot CPUs when going to offline with their interrupts disabled,
and never seen at boot CPU (core0 in our case).
Details:
serial_console_write() lacks of appropriate spinlock handling.
In SMP systems, as long as sci_transmit_chars() is being processed
at one CPU core, serial_console_write() can stuck at the other CPU
core(s), when it tries to access to the same serial port _without_
a proper locking. serial_console_write() waits for the transmit FIFO
getting empty, while sci_transmit_chars() writes data to the FIFO.
In general, peripheral interrupts are routed to boot CPU (core0) by
Linux ARM standard affinity settings. SCI(F) interrupts are handled
by core0, so sci_transmit_chars() is processed on core0 as well.
When logcat is running, it writes enormous log data to the kernel at
every moment, forever. So core0 can repeatedly continue to process
sci_transmit_chars() in its interrupt handler, which eventually makes
the other CPU core(s) stuck at serial_console_write().
Looking at serial/8250.c, this is a known console write lockup issue
with SMP kernels. Fix the sh-sci driver in the same way 8250.c does.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
About FIFO count, there are two variants of SCIFs which show
a) TX count in upper, RX count in lower byte of FDR register
b) TX count in TFDR register, RX count in RFDR register
Common SCIFB regmap in current source code is defined as "a".
At least 7372 and 73a0 HW manual say their SICFB are "b".
This patch alters the definition to "b", considering the current
one has come from a mistake. The reason is as follows.
The flag SCIFB sh-sci driver means it has 256 byte FIFO.
The count is from 0(empty) to 256(full), that makes 9-bit.
Because FDR is 16-bit register, it can not hold two 9-bits.
That's why, SCIFB can not be "a".
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current mask 0xff to SCTFDR/RFDR damages SCIFB, because the
registers on SCIFB have 9-bit data (0 to 256).
This patch changes the mask according to port->fifosize.
Though I'm not sure if the mask is really needed (I don't know if
there are variants which have non-zero upper bits), it is safer.
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support prescaler 1/16 and 1/64, in addition to current 1 and 1/4.
Supporting below 2400bps was dropped long time ago in mainline.
Since then, setting lower rate has been resulting in erroneous
register value, without indicating any errors through API.
This patch adds more prescaler to support lower rates again.
This still doesn't check range, but we won't hit the case because
even 50bps at 48MHz clock is now supported.
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 1ba7622094 (serial: sh-sci: console Runtime PM support,
from Magnus Damm <damm@opensource.se>, 2011-08-03), tried to support
console runtime PM, but unfortunately it didn't work for us for some
reason. We did not investigated further at that time, instead would
like to propose a different approach.
In Linux tty/serial world, to get console PM work properly, a serial
client driver does not have to maintain .runtime_suspend()/..resume()
calls itself, but can leave console power power management handling to
the serial core driver.
This patch moves the sh-sci driver in that direction.
Notes:
* There is room to optimize console runtime PM more aggressively by
maintaining additional local runtime PM calls, but as a first step
having .pm() operation would suffice.
* We still have a couple of direct calls to sci_port_enable/..disable
left in the driver. We have to live with them, because they're out
of serial core's help.
Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This partially reverts commit 1ba7622094 (serial: sh-sci: console
Runtime PM support, from Magnus Damm <damm@opensource.se>, 2011-08-03).
The generic 'serial_core' can take care of console PM maintenance,
so all (or at least the first thing) we have to do to get console PM
work properly, is to implement uart_ops ->pm() operation in the sh-sci
serial client driver.
This patch partially reverts the commit above, but leaving sci_reset()
change in place, because sci_reset() is already part of another commit
(73c3d53f38 serial: sh-sci: Avoid FIFO clear for MCE toggle.).
A revised version of console PM support follows next.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 5a50a01bf0 (sh-sci / PM: Use power.irq_safe, from
Rafael J. Wysocki <rjw@sisk.pl>, 2011-08-24).
In order to get console PM work properly, we should implement uart_ops
->pm() operation, rather than sprinkle band-ading runtime PM calls in
the driver.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 048be431e4 (sh-sci / PM: Avoid deadlocking runtime
PM, from Rafael J. Wysocki <rjw@sisk.pl>, 2012-03-09).
In order to get console PM work properly, we should implement uart_ops
->pm() operation, rather than sprinkle band-ading runtime PM calls in
the driver.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
To be sure, the TTY buffers (and later some stuff) are gone along with
the tty_port, we have to call tty_port_destroy at tear-down places.
This is mostly where the structure containing a tty_port is freed.
This patch does exactly that -- put tty_port_destroy at those places.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
This one is special as we need more work to be done. Previously,
the tty_port was initialized at module load time, but to be able to
destroy the port and init it again, we now do the initialization in
probe and destroy in remove. I.e. at more appropriate places for that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue.
Those using refcounting are safe now, but for those which do not we
introduce a function to be called right before the tty_port is freed
by the drivers.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
Here it is enough to switch to refcounting in tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
PTY is one of those, here we just need to use tty_port_put instead of
kfree. (Assuming tty_port_destructor does not need port->ops to be set
which we change here too.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not access unsafe port->tty pointer when we have a safe tty
already. Use the safe one.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With hotpluggable and memoryless nodes, it's possible that node 0 will
not be online, so use the first online node's zonelist rather than
hardcoding node 0 to pass a zonelist with all zones to the oom killer.
Signed-off-by: David Rientjes <rientjes@google.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch performs a small cleanup tty/Serial/Kconfig file by removing
unneeded ARCH dependencies. This dependencies already included in
board/type symbols.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is following what 8250 driver is doing in console write function,
to avoid the hardware lockup case.
v2: incldudes the <linux/nmi.h>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this we will shift data into oblivion and give wrong results on
some configurations
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Zynq platform requires the use of CONFIG_OF. Remove the #ifdef
conditionals in the uartps driver. Make dependency explicit in Kconfig.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should do hangup on dcd loss if CLOCAL is false not true.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=49911
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch check whether the fifo lenth is empty before writing new data to fifo.If condition
is true,ifx_spi_write need to trigger one mrdy_assert. If condition is false,the mrdy_assert
will be trigger by the next ifx_spi_io.
Cc: Bi Chao <chao.bi@intel.com>
Signed-off-by: Chen Jun <jun.d.chen@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to correct the bit mapping of "MORE" and "CTS" in SPI frame header.
Per SPI protocol, SPI header is encoded with length of 4 byte, which is defined
as below:
bit 0 ~ 11: current data size;
bit 12: "MORE" bit;
bit 13: reserve
bit 14 ~ 15: reserve
bit 16 ~ 27: next data size
bit 28: RI
bit 29: DCD
bit 30: CTS/RTS
bit 31: DSR/DTR
According to above SPI header structure, the bit mapping of "MORE" and "CTS" is
incorrect in function ifx_spi_decode_spi_header();
Cc: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The spi_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bdb498c200 "TTY: hvc_console, add tty install" took the port
refcounting out of hvc_open()/hvc_close(), but failed to remove the
kref_put() and tty_kref_put() calls in hvc_hangup() that were there to
remove the extra references that hvc_open() had taken.
The result was that doing a vhangup() when the current terminal was
a hvc_console, then closing the current terminal, would end up calling
destroy_hvc_struct() and making the port disappear entirely. This
meant that Fedora 17 systems would boot up but then not display the
login prompt on the console, and attempts to open /dev/hvc0 would
give a "No such device" error.
This fixes it by removing the extra kref_put() and tty_kref_put() calls.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This first patch serie start the cleanup of the header in mach
by moving all the platform data to include/linux/platform_data
and move the board header and drivers header next to them
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c5hx
-----END PGP SIGNATURE-----
Merge tag 'for-3.8-at91_header_clean' of git://github.com/at91linux/linux-at91 into next/headers
From Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
arm: at91: mach header cleanup
This first patch serie start the cleanup of the header in mach
by moving all the platform data to include/linux/platform_data
and move the board header and drivers header next to them
* tag 'for-3.8-at91_header_clean' of git://github.com/at91linux/linux-at91:
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When the UART device has hardware flow control enabled, it ignores the
MCR RTS bit in the MCR register, and keeps RTS asserted as long as we
continue to read characters from the UART receiver FIFO. This means
that when the TTY buffers become full, the UART doesn't tell the remote
end to stop sending, which causes the TTY layer to start dropping
characters.
A similar problem exists with software flow control. We need the FIFO
register to fill when software flow control is enabled to provoke the
UART to send the XOFF character.
Fix this by implementing the throttle/unthrottle callbacks, and use
these to disable receiver interrupts. This in turn means that the UART
FIFO will fill, which will then cause the UART's hardware to deassert
the RTS signal and/or send the XOFF character, stopping the remote end.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Simplify:
- set ECB
...
- LCR mode A
- clear TCRTLR
- LCR mode B
- clear ECB
- set ECB and update other bits
- LCR mode A
- update XONANY
to:
- set ECB
...
- LCR mode B
- set ECB and update other bits
- LCR mode A
- update XONANY and clear TCRTLR
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Take advantage of the switch to mode B for accessing the TCR register,
and move the xon/xoff configuration there. This allows further
simplication of this sequence.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We always setup the TCR register in the software flow control path,
and when hardware flow control is enabled. Remove this redundant
setup, and place it before we setup any hardware flow control.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We have the sequence:
- LCR mode B
- write EFR with ECB clear
- LCR mode normal
- if s/w flow
- LCR mode B
- write EFR with ECB clear
...
- LCR mode B
- write EFR with ECB clear
- LCR mode normal
This can be simplified to:
- if s/w flow
- LCR mode B
- write EFR with ECB clear
...
- LCR mode B
- write EFR with ECB clear
- LCR mode normal
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's really no reason to read back these registers while setting
the termios modes, provided we keep our cached copies up to date.
Remove these readbacks.
This has the benefit that we know that the EFR_ECB and MCR_TCRTLR
bits will always be clear, so we don't need to keep masking these
bits throughout the code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
struct uart_omap_port and struct uart_omap_dma, and associated
definitions are private to the driver, so there's no point them sitting
in an include file under arch/arm. Move them into the driver itself.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
irq_pending is never used, so let's remove it. It seems to be result
of a bad rebase of d37c6cebcb (serial: omap: move uart_omap_port
definition to C file)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MCR TCRTLR bit can only be changed when ECB is set in the EFR.
Unfortunately, several places were trying to alter this bit while ECB
was clear:
- serial_omap_configure_xonxoff() was attempting to clear the bit after
explicitly clearing the ECB bit.
- serial_omap_set_termios() was trying the same trick after setting the
SCR, and when trying to change the TCR register when hardware flow
control was enabled.
Fix this by ensuring that we always have ECB set whenever the TCRTLR bit
is changed.
Moreover, we start out by reading the EFR and MCR registers, which may
have indeterminent bit settings for the ECB and TCRTLR bits. Ensure
that these bits always start off in a known state.
In order to avoid any undesired behaviour appearing through fixing this,
we also ensure that hardware assisted flow control is disabled while new
driver specific parts are not in place.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
c538d20c7f (and maybe previous commits) broke set_mctrl() by making
it only capable of setting bits in the MCR register. This prevents
software controlled flow control and modem control line manipulation
via TIOCMSET/TIOCMBIC from working correctly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need to re-read EFR after we've recently written it; the
register is a configuration register which doesn't change its value
without us writing to it. The last value which was written to this
register was up->efr.
Removing this re-reading avoids the possibility that we end up with
up->efr having unintended bits set, which should only be temporarily
set when accessing the enhanced features.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SCD (special character detect) bit enables comparisons with XOFF2,
which we do not program. As the XOFF2 character remains unprogrammed,
there's little point enabling this feature along with its associated
interrupt. Remove this, and ensure that the SCD bit is cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Nothing was clearing the UART_MCR_XONANY bit, so once the ixany
mode gets set, there's no possibility to disable it. Clear this
bit when IXANY mode is cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is nothing which clears the auto RTS/CTS bits, so once hardware
flow control gets enabled, there's no possibility to disable it.
So, clear these bits when CRTSCTS is cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add two callbacks for hardware assisted flow control; we need to know
when the tty layers want us to stop and restart due to their buffer
levels.
Call a driver specific throttle/unthrottle function if and only if the
driver indicates that it is using an enabled hardware assisted flow
control method, otherwise fall back to the non-hardware assisted
methods.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ports which are handling h/w flow control in hardware must not have
their RTS state altered depending on the tty's hardware-stopped state.
Avoid this additional logic when setting the termios state.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ports which are capable of handling s/w flow control in hardware to
know when the s/w flow control termios settings are changed. Add a
flag to allow the low level serial drivers to indicate that they
support this, and these changes should be propagated to them.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In case of error, the function clk_get() returns ERR_PTR()
and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to implement following 2 places to avoid potential error when IFX6x60 port shutdown:
1) Clear Flag IFX_SPI_STATE_IO_AVAILABLE to disable data transfer when Modem port is shutdown;
2) Clear Flag IFX_SPI_STATE_IO_IN_PROGRESS and IFX_SPI_STATE_IO_READY when reopen port.
This is because last port shutdown may happen when SPI/DMA transfer is in progress, if the last
data transfer is not completed(for example due to modem reset), the Flag IFX_SPI_STATE_IO_IN_PROGRESS
will be set forever, so when IFX port is activated again, IFX_SPI_STATE_IO_IN_PROGRESS will prevent
transferring data forever. And if don't clear IFX_SPI_STATE_IO_READY, it may cause one more SPI frame
transferring in spit there is not data need to be transfer.
cc: liu chuansheng <chuansheng.liu@intel.com>
cc: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver for non-standard on-chip UART, instantiated in the ARC (Synopsys)
FPGA Boards such as ARCAngel4/ML50x
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We pass both port and state because the original caller had both to hand.
With all the attribute callers this won't be true so do the conversion in
the function itself.
The current callers all do lock/query/unlock. This won't be true for future
set based cases but there are plenty of get ones that will exist so split
the code with a helper for the future cases.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The two patches needed are now in the tree. The first added the sysfs
interface and directly accesses the uartclk. The second provides a
proper interface for getting the values.
Wire them together.
This formes a basis for both get and set methods for any of the other uart
properties and we can now fill them out further.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These printks should all be emitted at KERN_DEBUG level.
Make them dependent on CONFIG_DEBUG or (#define DEBUG)
simplify the code a bit.
Add missing newlines where appropriate.
Most all of these messages could be deleted too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge reason: development work has dependency on kvm patches merged
upstream.
Conflicts:
arch/powerpc/include/asm/Kbuild
arch/powerpc/include/asm/kvm_para.h
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
For checkpoint/restore we need to know if tty has
exclusive or packet mode set, as well as if pty
is currently locked. Just to be able to restore
this characteristics.
For this sake the following ioctl codes are introduced
- TIOCGPKT to get packet mode state
- TIOCGPTLCK to get Pty locked state
- TIOCGEXCL to get Exclusive mode state
Note this ioctls are a bit unsafe in terms of data
obtained consistency. The tty characteristics might
be changed right after ioctl complete. Keep it in
mind and use this ioctl carefully.
v2:
- Use TIOC prefix for ioctl codes (by jslaby@)
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Pavel Emelyanov <xemul@parallels.com>
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since this ioctl is for pty devices only move it to pty.c.
v2:
- drop PTY_TYPE_MASTER test since it's master peer
ioctl anyway (by jslaby@)
Suggested-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Pavel Emelyanov <xemul@parallels.com>
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently this driver expects the clock-frequency attribute. This
patch allows getting clock-frequency through clk driver API
clk_get_rate() if clock-frequency attribute is not defined.
So in the device bindings for serial device, one can add clocks
phandle to refer to the clk device to get the rate.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WARN_RATELIMIT() expects the warning to end with a newline if one
is needed.
Not doing so results in odd looking warnings such as:
[ 1339.454272] tty is NULLPid: 7147, comm: kworker/4:0 Tainted: G W 3.7.0-rc2-next-20121025-sasha-00001-g673f98e-dirty #75
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch make use of del_timer instead of del_timer_sync in the
interrupt context.
The spi_timer function don't use any resources that may release after
running del_timer,
so using the del_timer is also safe and enough in this context.
Signed-off-by: Chen Jun <jun.d.chen@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Tested-by: Chuansheng Liu <chuansheng.liu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch make use of mod_timer instead of add_timer in the mrdy_assert function.
Because the srdy interrupter can go high when we are running function mrdy_assert and mrdy_assert
can be called by multi-entry. In our medfield platform, spi stress test can encounter this
error logs triggered by the BUG_ON of add_timer function.This patch had been tested on
our medfield platform.
the scenario:
CPU0 CPU1
mrdy_assert
set_bit(IFX_SPI_STATE_TIMER_PENDING)
ifx_spi_handle_srdy
...
clear_bit(IFX_SPI_STATE_TIMER_PENDING)
...
mrdy_assert
set_bit(IFX_SPI_STATE_TIMER_PENDING)
...
add_timer
...
add_timer
Cc: liu chuansheng <chuansheng.liu@intel.com>
Cc: Bi Chao <chao.bi@intel.com>
Signed-off-by: Chen Jun <jun.d.chen@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPI protocol driver only provide one function (swap_buf()) to swap SPI
data into big endian format, which is only available when SPI
controller's word width is 16 bits. But word width could be configured
as 8/16/32 bits, different word width configure should be mapped to
different swap methods.This patch is to make SPI protocol driver choose
the right swap function corresponding to SPI word width configuration.
cc: liu chuansheng <chuansheng.liu@intel.com>
cc: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This switches a bunch of allocation and remapping to use the
devm_* garbage collected methods and cleans up the error
path and remove() paths consequently.
devm_ioremap() is only in <linux/io.h> so fix up the
erroneous <asm/*> include as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the array serial_omap_console_ports is hard coded to 4.
Make it depend on the maximum uart count.
Post to [cfc55bc ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6]
the max ports is 6.
Cc: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Special character detect enable if enabled by default.Received data
comparison with XOFF2 data happens by default.
tty provides only XOFF1 no X0FF2 is provided so no need
to enable check for XOFF2.
Keeping this enabled might give some slow transfers due to dummy xoff2
comparison with xoff2 reset value.
Since not all want the XOFF2 support lets not enable it by
default.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_context_loss_count returns an int however it is stored in
unsigned integer context_loss_cnt . This patch tries to make
context_loss_cnt int. So that in case of errors the value
(which may be negative) is not interpreted wrongly.
In serial_omap_runtime_resume in case of errors returned by
get_context_loss_count print a warning and do a restore.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 957ee7270d
(serial: omap: fix software flow control).
As Russell has pointed out, that commit isn't fixing
Software Flow Control at all, and it actually makes
it even more broken.
It was agreed to revert this commit and use Russell's
latest UART patches instead.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch converts all static variables of clps711x serial driver
to dynamic allocating. In this case we are should remove console_initcall()
and declare console during driver registration. Early kernel messages can
be retrieved by add "earlyprintk" option to the kernel command line.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Actually, in order to support KGDB over serial console one must
implement two callbacks for character polling. Clone them from
8250 driver with a bit of tuning.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Marko Katic <dromede@gmail.com>
CC: Eric Miao <eric.y.miao@gmail.com>
CC: Russell King <linux@arm.linux.org.uk>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
drivers/tty/serial/pxa.c | 55 ++++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 55 insertions(+), 0 deletions(-)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The global "normal" spin lock that guards the line discipline
administration is replaced by a raw spin lock. On a PREEMPT_RT system this
prevents unwanted scheduling overhead around the line discipline administration.
On a 200 MHz AT91SAM9261 processor setup this fixes about 100us of scheduling
overhead on a TTY read or write call.
Signed-off-by: Ivo Sieben <meltedpianoman@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing unlock on the error handling path in function
hvcs_initialize().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
