This patch fixes an issue that sometimes this controller is not able
to complete the Control write status stage.
This driver should enable DCPCTR.CCPL and PID_BUF to complete the status
stage. However, if this driver detects the ctrl_stage interruption first
before the control write data is received, this driver will clear the
PID_BUF wrongly in the usbhsf_pio_try_pop(). To avoid this issue, this
patch doesn't clear the PID_BUF in the usbhsf_pio_try_pop().
(Since also the privious code doesn't disable the PID_BUF after a control
transfer was finished, this patch doesn't have any side efforts.)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes an issue for control write. When usbhsf_prepare_pop()
is called after this driver called a gadget setup function, this controller
doesn't receive the control write data. So, this patch adds a code to clear
the fifo for control write in usbhsf_prepare_pop().
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the DT should describe the hardware (not the driver limitation),
This patch revises the binding document about the dma-names to change
simple numbering as "ch%d" instead of "tx<n>" and "rx<n>".
Also this patch fixes the actual code of renesas_usbhs driver to handle
the new dma-names.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some Renesas SoCs have the USB-DMAC. It is able to terminate transfers
when a short packet is received, even if less bytes than the transfer
counter size have been received. Also, it is able to send a short
packet even if the packet size is not multiples of 8bytes.
Since the previous code has used the interruption of USBHS controller
when receiving packets even if this driver has used a dmac, a lot of
interruptions has happened. This patch will reduce such interruptions.
This patch allows to use the USB-DMAC on R-Car H2 and M2.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the setup sequence in xfer_work(). Otherwise,
sometimes a usb transaction will get stuck.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To connect the channel of USB-DMAC to USBHS DnFIFO number, this patch
adds this channel/FIFO number in dma-names. Otherwise, this driver
needs to add analysis code for device tree.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes an issue that the following commit causes NULL
pointer dereference in dma_release_channel().
"usb: renesas_usbhs: add support for requesting DT DMA"
(commit id abd2dbf6bb)
The usbhsf_dma_init_dt() should set fifo->{t,r}x_chan to NULL if
dma_request_slave_channel_reason() returns IS_ERR value.
Otherwise, usbhsf_dma_quit() will call dma_release_channel(), and then
NULL pointer dereference happens.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To add support for requesting DT DMA in the future, this patch adds
usbhsf_dma_init_pdev() function.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch expands USB-DMAC channels for R-Car Gen2 SoCs. The SoCs
have 4 channels. If d{2,3}_{t,x}x_id are not set, this driver never
uses the expanded USB-DMAC channels.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To extend DnFIFOs in the future, this patch adds a new macro because
some SoCs don't the "port" address for DnFIFOs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To expand DnFIFOs in the future, this patch standardizes the d{0,1}fifo
control using new macros.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To extend DnFIFOs in the future, this patch changes d{0,1}fifo of
usbhs_fifo_info to dfifo array.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the DCPCTR doesn't have the ACLRM bit, the usbus_pipe_clear()
should not call the usbhsp_pipectrl_set() with ACLRM.
So, this patch fixes this issue to add the usbhs_fifo_clear_dcp()
in fifo.c because the controller needs the CFIFO to clear the
the DCP PIPE.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the datasheet, this driver should clear the INTSTS0.CTRT
bit before this controller detects the next stage transition. Otherwise,
the driver may not be able to clear the bit after the controller went to
the next stage transition. After that, the driver will not be able to
clear the INTSTS0.VALID, and a usb control transfer will not finish
finally.
If we use the testusb tool, it is easy to reproduce this issue:
# testusb -a -t 10
Since the previous code handled a data stage and a status stage in
the usbhsf_pio_try_push(), it may not clear the INTSTS0.CTRT at the
right timing.
So, this patch change the timing of usbhs_dcp_control_transfer_done()
to the usbhsg_irq_ctrl_stage().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the usb_pkt_pop(). If a gadget driver calls
usb_ep_dequeue(), this driver will call the usb_pkt_pop().
So, the usb_pkt_pop() should cancel the transaction.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the condition of is_done in usbhsf_dma_push_done().
This function will be called after a transmission finished by DMAC.
So, the function should check if the transmission packet is short packet
or not. Also the function should call try_run to send the zero packet
by the pio handler if the "*is_done" is not set. Otherwize, the
transaction will not finish if a gadget driver sets the "zero" flag
in a transmission.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some gadget drivers will call usb_ep_queue() more than once before
the first queue doesn't finish. However, this driver didn't handle
it correctly. So, this patch fixes the behavior of some
usbhs_pkt_handle using the "running" flag. Otherwise, the oops below
happens if we use g_ncm driver and when the "iperf -u -c host -b 200M"
is running.
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 80000007 [#1] SMP ARM
Modules linked in: usb_f_ncm g_ncm libcomposite u_ether
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 3.17.0-rc1-00008-g8b2be8a-dirty #20
task: c051c7e0 ti: c0512000 task.ti: c0512000
PC is at 0x0
LR is at usbhsf_pkt_handler+0xa8/0x114
pc : [<00000000>] lr : [<c0278fb4>] psr: 60000193
sp : c0513ce8 ip : c0513c58 fp : c0513d24
r10: 00000001 r9 : 00000193 r8 : eebec4a0
r7 : eebec410 r6 : eebe0c6c r5 : 00000000 r4 : ee4a2774
r3 : 00000000 r2 : ee251e00 r1 : c0513cf4 r0 : ee4a2774
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current usbhs gadget driver didn't complete STATUS stage after receiving.
It wasn't problem for us before, because some USB class doesn't use
DATA OUT stage in control transfer.
But, it is required on some device.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DMAEngine uses IRQ if dma_request_channel() was called,
and it is using devm_request_irq() today,
OTOH, dma_request_channel() will be called when each
USB connection happened on this driver.
This means same IRQ will be requested many times
whenever each USB connected,
and this IRQ isn't freed when USB disconnected.
Request DMAEngine once.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
renesas_usbhs implements ->pullup() method, switches over
to devm_request_irq(), adds support for DMA Engine and
got a few miscelaneous cleanups.
The NCM gadget got an endianness fix and the Ethernet
gadget a frame size fix.
We're finally removing the g_file_storage gadget and
sticking to g_mass_storage and the new tcm_usb_gadget
gadgets since that was a huge duplicaton of effort anyway.
While removing g_file_storage, we also had to fix a bunch
of defconfigs which were still pointing to the old gadget.
There's a big series getting us closer to being able to
introduce our configfs interface. The series converts
functions into loadable modules which will, eventually,
be registered to the configfs interface.
Other than that there's the usual typo fixes and miscelaneous
cleanups all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQnXPMAAoJEIaOsuA1yqREkygQALIuhY6veRPZoZJltuADeAOV
h7lBkuseJxvlJsbMLnjqP5tw4W/haE1deGR+ee1ZItkPrERCX1++jkQ6hmm7e00R
mvr8rI+n3eBHSKUO89tUfCaz5UBsTl0cowPWdTwxRrV4VRJ1wVBw/oII9sfyss03
jDo+11DSjTGTB+Bz72p2NTkRiv9my2Kz+ihhqFR5VSl5FyoutG53RNKRmciJKGB+
i+RptOI+prdW1uOURHbie5FAI0xOBrE1Up2XdNiZ9blT6zcsK754Lc8erFJEZXX5
7s8Ys/HJZLQCF/fRt4WAw8e1lSPELD2xuDMqV+WKu93aXOiAWL1SbzqK3Y+PaUDg
Red07jOxgPqgq0F1mAp3+0Rs1RnshSvKREtQhZqsttg7suXhDB0q7h61CX8uQbRA
hBZh8eFexRjqOZxveeV+h4ATz00c2nlEa8cJscr5zLf4R/LSxJWT7LV5227BDkBV
9NUMA3dunDYZLqnxBv5lS2gQzmYO6G11wzdpgjnABL2WlM8Pv1lUDhY+erwvTRzd
BM+9qMd7K40BuI1JyUsbBdmuEpJAD/yWE77pT2aBrr4767x0CYjBPZqQAxXFcWi8
5NG1BzqWmH9HhwxKyWueWgNgY253cRcAzFlUN80NRA2UuNkMAeOAeJjvK48isAqJ
T1MUkQgIFNvSecpRPrEl
=umtl
-----END PGP SIGNATURE-----
Merge tag 'gadget-for-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB gadget patches from Felipe:
"usb: gadget: patches for v3.8
renesas_usbhs implements ->pullup() method, switches over
to devm_request_irq(), adds support for DMA Engine and
got a few miscelaneous cleanups.
The NCM gadget got an endianness fix and the Ethernet
gadget a frame size fix.
We're finally removing the g_file_storage gadget and
sticking to g_mass_storage and the new tcm_usb_gadget
gadgets since that was a huge duplicaton of effort anyway.
While removing g_file_storage, we also had to fix a bunch
of defconfigs which were still pointing to the old gadget.
There's a big series getting us closer to being able to
introduce our configfs interface. The series converts
functions into loadable modules which will, eventually,
be registered to the configfs interface.
Other than that there's the usual typo fixes and miscelaneous
cleanups all over the place."
received data will break if it was bulk pipe and large data size,
because pipe kept BUF PID even though it doesn't have enough buffer.
To avoid this issue, renesas_usbhs can use transfer counter.
Pipe PID will be NAK if it didn't have enough buffer by this patch.
renesas_usbhs has strange address mapping.
Thus, it is difficult to calculate transfer counter setting address.
This patch use fixed table for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
mod.h has irq_bempsts/irq_brdysts to keep each irq status,
but it was difficult to find where they were used
on renesas_usbhs driver by using "grep irq_xxxx" command,
since it used irq_##status macro.
This patch fixup them
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
renesas_usbhs driver can switch DMA/PIO transfer by using handler,
and each handler have push/pop direction.
But unfortunately, current dma push handler didn't a path
which calls usbhs_pipe_enable(). Thus, dma transfer never happened.
this patch fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
renesas_usbhs dma can transport 8byte alignment data, not 4byte.
This patch fixup it.
Reported-by: Sugnan Prabhu S <sugnan.prabhu@renesasmobile.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here's the big USB patch set for the 3.6-rc1 merge window.
Lots of little changes in here, primarily for gadget controllers and drivers.
There's some scsi changes that I think also went in through the scsi tree, but
they merge just fine. All of these patches have been in the linux-next tree
for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAQhpcACgkQMUfUDdst+yms4wCgpMbfFYTZ8lHpDnXHYFv6qw8j
FIsAmwT4mbT7m8C0k+ELV/5T2e0eYJEQ
=QetG
-----END PGP SIGNATURE-----
Merge tag 'usb-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB patch set for the 3.6-rc1 merge window.
Lots of little changes in here, primarily for gadget controllers and
drivers. There's some scsi changes that I think also went in through
the scsi tree, but they merge just fine. All of these patches have
been in the linux-next tree for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up trivial conflicts in include/scsi/scsi_device.h (same libata
conflict that Jeff had already encountered)
* tag 'usb-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
usb: Add USB_QUIRK_RESET_RESUME for all Logitech UVC webcams
usb: Add quirk detection based on interface information
usb: s3c-hsotg: Add header file protection macros in s3c-hsotg.h
USB: ehci-s5p: Add vbus setup function to the s5p ehci glue layer
USB: add USB_VENDOR_AND_INTERFACE_INFO() macro
USB: notify phy when root hub port connect change
USB: remove 8 bytes of padding from usb_host_interface on 64 bit builds
USB: option: add ZTE MF821D
USB: sierra: QMI mode MC7710 moved to qcserial
USB: qcserial: adding Sierra Wireless devices
USB: qcserial: support generic Qualcomm serial ports
USB: qcserial: make probe more flexible
USB: qcserial: centralize probe exit path
USB: qcserial: consolidate usb_set_interface calls
USB: ehci-s5p: Add support for device tree
USB: ohci-exynos: Add support for device tree
USB: ehci-omap: fix compile failure(v1)
usb: host: tegra: pass correct pointer in ehci_setup()
USB: ehci-fsl: Update ifdef check to work on 64-bit ppc
USB: serial: keyspan: Removed unrequired parentheses.
...
Pull slave-dmaengine update from Vinod Koul:
"This time we have a new dmaengine driver from the tegra folks. Also
we have Guennadi's cleanup of sh drivers which incudes a library for
sh drivers. And the usual odd fixes in bunch of drivers and some nice
cleanup of dw_dmac from Andy."
Fix up conflicts in drivers/mmc/host/sh_mmcif.c
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: Cleanup logging messages
mmc: sh_mmcif: switch to the new DMA channel allocation and configuration
dma: sh: provide a migration path for slave drivers to stop using .private
dma: sh: use an integer slave ID to improve API compatibility
dmaengine: shdma: prepare to stop using struct dma_chan::private
sh: remove unused DMA device pointer from SIU platform data
ASoC: siu: don't use DMA device for channel filtering
dmaengine: shdma: (cosmetic) simplify a static function
dmaengine: at_hdmac: add a few const qualifiers
dw_dmac: use 'u32' for LLI structure members, not dma_addr_t
dw_dmac: mark dwc_dump_lli inline
dma: mxs-dma: Export missing symbols from mxs-dma.c
dma: shdma: convert to the shdma base library
ASoC: fsi: prepare for conversion to the shdma base library
usb: renesas_usbhs: prepare for conversion to the shdma base library
ASoC: siu: prepare for conversion to the shdma base library
serial: sh-sci: prepare for conversion to the shdma base library
mmc: sh_mobile_sdhi: prepare for conversion to the shdma base library
mmc: sh_mmcif: remove unneeded struct sh_mmcif_dma, prepare to shdma conversion
dma: shdma: prepare for conversion to the shdma base library
...
This patch used dmaengine helper functions instead of using hand setting.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few quoted includes start with a superfluous "./". Clean up those
quoted includes.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull slave-dmaengine update from Vinod Koul:
"This includes the cookie cleanup by Russell, the addition of context
parameter for dmaengine APIs, more arm dmaengine driver cleanup by
moving code to dmaengine, this time for imx by Javier and pl330 by
Boojin along with the usual driver fixes."
Fix up some fairly trivial conflicts with various other cleanups.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
dmaengine: imx: fix the build failure on x86_64
dmaengine: i.MX: Fix merge of cookie branch.
dmaengine: i.MX: Add support for interleaved transfers.
dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
dmaengine: imx-dma: remove internal structure.
dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
dmaengine: imx-dma: remove sg member from internal structure.
dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
dmaengine: imx-dma: remove dma_mode member of internal structure.
dmaengine: imx-dma: remove data member from internal structure.
dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
dmaengine: at_hdmac: add slave config operation
dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
dmaengine/dma_slave: introduce inline wrappers
dma: imx-sdma: Treat firmware messages as warnings instead of erros
...
Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The current renesas_usbhs driver triggers
BUG: scheduling while atomic: ksoftirqd/0/3/0x00000102
with enabled CONFIG_DEBUG_ATOMIC_SLEEP, by submitting DMA transfers from
an atomic (tasklet) context, which is not supported by the shdma dmaengine
driver. Fix it by switching to a work.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
list.h already provide helpers to find the first entry and to move list
nodes to the tail of another list. This patch simply uses those helpers,
no functional changes.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The SUDMAC uses 8-bit width only. So, when the driver uses SUDMAC,
we have to clear the MBW_32.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
driver has to re-use the limited pipe for each device/endpoint
when it is USB host hub mode, since number of pipe has limitation.
Then, each pipe should care own pipe sequence for next packet.
This patch adds sequence control.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fixup usage of dma direction by introducing dma_transfer_direction,
this patch moves usb/renesas driver to use new enum
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
usbhs_pkt_push() had inconsistent return under spin lock.
This patch fix it up.
Special thanks to Dan
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
| drivers/usb/renesas_usbhs/fifo.c: In function ‘usbhsf_dma_prepare_push’:
| drivers/usb/renesas_usbhs/fifo.c:823:7: warning: cast from pointer \
to integer of different size [-Wpointer-to-int-cast]
| drivers/usb/renesas_usbhs/fifo.c: In function ‘usbhsf_dma_try_pop’:
| drivers/usb/renesas_usbhs/fifo.c:900:7: warning: cast from pointer \
to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Felipe Balbi <balbi@ti.com>
When data read interrupt happened, the pipe is BUF which means "enable".
then, next un-necessary interrupt/token might be
issued again when all data were popped from fifo.
It will cause un-understandable bug.
This patch decides pipe disable on top of read interrupt.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Automatically packet start by usbhs_pkt_push() was useful.
But the pushed packet will be called twice
if new packet was pushed on usbhs_pkt :: done callback.
(1st is called by usbhs_pkt_push(), 2nd is called by usbhsf_pkt_handler())
This patch disables automatic packet start,
and clarified packet start timing.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
transfer done function was registered in struct struct usbhs_pipe_info.
It was good for mod_gadget, but not good for mod_host.
This function move it to struct usbhs_pkt.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was no method to get struct usbhs_priv when
packet transfer done function was called.
This patch allow that callback function receive it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
renesas_usbhs device needs special bit settings
if it was mod_host and dcp pipe.
This patch support it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
