According to the RM, the CCGR101 is shared for the following root clocks:
- AUDIO_AHB_CLK_ROOT
- AUDIO_AXI_CLK_ROOT
- SAI1_CLK_ROOT
- SAI2_CLK_ROOT
- SAI3_CLK_ROOT
- SAI5_CLK_ROOT
- SAI6_CLK_ROOT
- SAI7_CLK_ROOT
- PDM_CLK_ROOT
IMX8MP_CLK_AUDIO_ROOT is same as AUDIO_AHB_CLK_ROOT
which can avoid break any users.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/1667811007-19222-3-git-send-email-shengjiu.wang@nxp.com
The PLL146x is used to implement SYS_PLL3 on i.MX8MP and can be used
to drive UARTn_ROOT clock. By setting the PLL3 to 320 MHz or 640 MHz,
the PLL3 output can be divided down to supply UARTn_ROOT clock with
precise 64 MHz, which divided down further by 16x oversampling factor
used by the i.MX UART core yields 4 Mbdps baud base for the UART IP.
This is useful e.g. for BCM bluetooth chips, which can operate up to
4 Mbdps.
Add 320 MHz and 640 MHz entries so the PLL can be configured accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20221031204838.195292-1-marex@denx.de
Keep sys ctr clock always on to make sure its register
can be accessed for cpuidle.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20221028095211.2598312-7-peng.fan@oss.nxp.com
During Linux System suspend/resume stress test after System Sleep
enabled, system will stuck sometimes. It is because NICMIX is powered
down, which HSIOMIX(always on) is not powered down. When NICMIX
powering down, HSIOMIX will get a hardware handshake, without HSIO ROOT clk,
the handshake will lose. Then after NICMIX power on when system resume,
the access to HSIOMIX through NICMIX would be broken. So keep HSIO ROOT
always on.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20221028095211.2598312-6-peng.fan@oss.nxp.com
Per Reference Mannual System Clocks Table,
LPIT1 and TPM1 sources from bus_aon_root
LPIT2 and TPM3 sources from bus_wakeup_root
So update driver to reflect that.
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20221028095211.2598312-5-peng.fan@oss.nxp.com
Per update Reference Mannual, correct the enet clock parent to
wakeup_axi_root.
Fixes: 24defbe194 ("clk: imx: add i.MX93 clk")
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20221028095211.2598312-3-peng.fan@oss.nxp.com
The anatop base is not unmapped during error handling path, fix it.
Fixes: 24defbe194 ("clk: imx: add i.MX93 clk")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20221028095211.2598312-2-peng.fan@oss.nxp.com
32K usb suspend clock gate is shared with usb_root_clk, this
shared clock gate was initially defined only for usb suspend
clock, usb suspend clk is kept on while system is active or
system sleep with usb wakeup enabled, so usb root clock is
fine with this situation; with the commit cf7f3f4fa9
("clk: imx8mp: fix usb_root_clk parent"), this clock gate is
changed to be for usb root clock, but usb root clock will
be off while usb is suspended, so usb suspend clock will be
gated too, this cause some usb functionalities will not work,
so define this clock to be a shared clock gate to conform with
the real HW status.
Fixes: 9c140d9926 ("clk: imx: Add support for i.MX8MP clock driver")
Cc: stable@vger.kernel.org # v5.19+
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/1664549663-20364-2-git-send-email-jun.li@nxp.com
Correct IMX93_CLK_FLEXSPI1_GATE CCGR setting. Otherwise the flexspi
always can't be assigned to a parent clock when dump the clock tree.
Fixes: 24defbe194 ("clk: imx: add i.MX93 clk")
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/1666589199-1199-1-git-send-email-haibo.chen@nxp.com
late breaking reports that a patch series to rework clk rate range
support broke boot on some devices, so I've left that branch out of this
PR. Hopefully we can get to that next week, or punt on it and let it
bake another cycle. That means we don't really have any changes to the
core framework this time around besides a few typo fixes. Instead this
is all clk driver updates and fixes.
The usual suspects are here (again), with Qualcomm dominating the
diffstat. We look to have gained support for quite a few new Qualcomm
SoCs and Dmitry worked on updating many of the existing Qualcomm drivers
to use clk_parent_data. After that we have MediaTek drivers getting some
much needed updates, in particular to support GPU DVFS. There are also
quite a few Samsung clk driver patches, but that's mostly because there
was a maintainer change and so last release we missed some of those
patches.
Overall things look normal, but I'm slowly reviewing core framework code
nowadays and that shows given the rate range patches had to be yanked
last minute. Let's hope this situation changes soon.
New Drivers:
- Support for Renesas VersaClock7 clock generator family
- Add Spreadtrum UMS512 SoC clk support
- New clock drivers for MediaTek Helio X10 MT6795
- Display clks for Qualcomm SM6115, SM8450
- GPU clks for Qualcomm SC8280XP
- Qualcomm MSM8909 and SM6375 global and SMD RPM clk drivers
Deleted Drivers:
- Remove DaVinci DM644x and DM646x clk driver support
Updates:
- Convert Baikal-T1 CCU driver to platform driver
- Split reset support out of primary Baikal-T1 CCU driver
- Add some missing clks required for RPiVid Video Decoder on RaspberryPi
- Mark PLLC critical on bcm2835
- More devm helpers for fixed rate registration
- Various PXA168 clk driver fixes
- Add resets for MediaTek MT8195 PCIe and USB
- Miscellaneous of_node_put() fixes
- Nuke dt-bindings/clk path (again) by moving headers to dt-bindings/clock
- Convert gpio-clk-gate binding to YAML
- Various fixes to AMD/Xilinx Zynqmp clk driver
- Graduate AMD/Xilinx "clocking wizard" driver from staging
- Add missing DPI1_HDMI clock in MT8195 VDOSYS1
- Clock driver changes to support GPU DVFS on MT8183, MT8192, MT8195
- Fix GPU clock topology on MT8195
- Propogate rate changes from GPU clock gate up the tree
- Clock mux notifiers for GPU-related PLLs
- Conversion of more "simple" drivers to mtk_clk_simple_probe()
- Hook up mtk_clk_simple_remove() for "simple" MT8192 clock drivers
- Fixes to previous |struct clk| to |struct clk_hw| conversion on MediaTek
- Shrink MT8192 clock driver by deduplicating clock parent lists
- Change order between 'sim_enet_root_clk' and 'enet_qos_root_clk'
clocks for i.MX8MP
- Drop unnecessary newline in i.MX8MM dt-bindings
- Add more MU1 and SAI clocks dt-bindings Ids
- Introduce slice busy bit check for i.MX93 composite clock
- Introduce white list bit check for i.MX93 composite clock
- Add new i.MX93 clock gate
- Add MU1 and MU2 clocks to i.MX93 clock provider
- Add SAI IPG clocks to i.MX93 clock provider
- add generic clocks for U(S)ART available on SAMA5D2 SoCs
- reset controller support for Polarfire clocks
- .round_rate and .set rate support for clk-mpfs
- code cleanup for clk-mpfs
- PLL support for PolarFire SoC's Clock Conditioning Circuitry
- Add watchdog, I2C, pin control/GPIO, and Ethernet clocks on R-Car V4H
- Add SDHI, Timer (CMT/TMU), and SPI (MSIOF) clocks on R-Car S4-8
- Add I2C clocks and resets on RZ/V2M
- Document clock support for the RZ/Five SoC
- mux-variant clock using the table variant to select parents
- clock controller for the rv1126 soc
- conversion of rk3128 to yaml and relicensing of the yaml bindings
to gpl2+MIT (following dt-binding guildelines)
- Exynos7885: add FSYS, TREX and MFC clock controllers
- Exynos850: add IS and AUD (audio) clock controllers with bindings
- ExynosAutov9: add FSYS clock controllers with bindings
- ExynosAutov9: correct clock IDs in bindings of Peric 0 and 1 clock
controllers, due to duplicated entries. This is an acceptable ABI
break: recently developed/added platform so without legacies, acked
by known users/developers
- ExynosAutov9: add few missing Peric 0/1 gates
- ExynosAutov9: correct register offsets of few Peric 0/1 clocks
- Minor code improvements (use of_device_get_match_data() helper, code
style)
- Add Krzysztof Kozlowski as co-maintainer of Samsung SoC clocks, as he
already maintainers that architecture/platform
- Keep Qualcomm GDSCs enabled when PWRSTS_RET flag is there, solving retention
issues during suspend of USB on Qualcomm sc7180/sc7280 and SC8280XP
- Qualcomm SM6115 and QCM2260 are moved to reuse PLL configuration
- Qualcomm SDM660 SDCC1 moved to floor clk ops
- Support for the APCS PLLs for Qualcomm IPQ8064, IPQ8074 and IPQ6018 was
added/fixed
- The Qualcomm MSM8996 CPU clocks are updated with support for ACD
- Support for Qualcomm SDM670 GCC and RPMh clks was added
- Transition to parent_data, parent_hws and use of ARRAY_SIZE() for
num_parents was done for many Qualcomm SoCs
- Support for per-reset defined delay on Qualcomm was introduced
-----BEGIN PGP SIGNATURE-----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=9jI+
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have some late breaking reports that a patch series to rework clk
rate range support broke boot on some devices, so I've left that
branch out of this. Hopefully we can get to that next week, or punt on
it and let it bake another cycle. That means we don't really have any
changes to the core framework this time around besides a few typo
fixes. Instead this is all clk driver updates and fixes.
The usual suspects are here (again), with Qualcomm dominating the
diffstat. We look to have gained support for quite a few new Qualcomm
SoCs and Dmitry worked on updating many of the existing Qualcomm
drivers to use clk_parent_data. After that we have MediaTek drivers
getting some much needed updates, in particular to support GPU DVFS.
There are also quite a few Samsung clk driver patches, but that's
mostly because there was a maintainer change and so last release we
missed some of those patches.
Overall things look normal, but I'm slowly reviewing core framework
code nowadays and that shows given the rate range patches had to be
yanked last minute. Let's hope this situation changes soon.
New Drivers:
- Support for Renesas VersaClock7 clock generator family
- Add Spreadtrum UMS512 SoC clk support
- New clock drivers for MediaTek Helio X10 MT6795
- Display clks for Qualcomm SM6115, SM8450
- GPU clks for Qualcomm SC8280XP
- Qualcomm MSM8909 and SM6375 global and SMD RPM clk drivers
Deleted Drivers:
- Remove DaVinci DM644x and DM646x clk driver support
Updates:
- Convert Baikal-T1 CCU driver to platform driver
- Split reset support out of primary Baikal-T1 CCU driver
- Add some missing clks required for RPiVid Video Decoder on
RaspberryPi
- Mark PLLC critical on bcm2835
- More devm helpers for fixed rate registration
- Various PXA168 clk driver fixes
- Add resets for MediaTek MT8195 PCIe and USB
- Miscellaneous of_node_put() fixes
- Nuke dt-bindings/clk path (again) by moving headers to
dt-bindings/clock
- Convert gpio-clk-gate binding to YAML
- Various fixes to AMD/Xilinx Zynqmp clk driver
- Graduate AMD/Xilinx "clocking wizard" driver from staging
- Add missing DPI1_HDMI clock in MT8195 VDOSYS1
- Clock driver changes to support GPU DVFS on MT8183, MT8192, MT8195
- Fix GPU clock topology on MT8195
- Propogate rate changes from GPU clock gate up the tree
- Clock mux notifiers for GPU-related PLLs
- Conversion of more "simple" drivers to mtk_clk_simple_probe()
- Hook up mtk_clk_simple_remove() for "simple" MT8192 clock drivers
- Fixes to previous |struct clk| to |struct clk_hw| conversion on
MediaTek
- Shrink MT8192 clock driver by deduplicating clock parent lists
- Change order between 'sim_enet_root_clk' and 'enet_qos_root_clk'
clocks for i.MX8MP
- Drop unnecessary newline in i.MX8MM dt-bindings
- Add more MU1 and SAI clocks dt-bindings Ids
- Introduce slice busy bit check for i.MX93 composite clock
- Introduce white list bit check for i.MX93 composite clock
- Add new i.MX93 clock gate
- Add MU1 and MU2 clocks to i.MX93 clock provider
- Add SAI IPG clocks to i.MX93 clock provider
- add generic clocks for U(S)ART available on SAMA5D2 SoCs
- reset controller support for Polarfire clocks
- .round_rate and .set rate support for clk-mpfs
- code cleanup for clk-mpfs
- PLL support for PolarFire SoC's Clock Conditioning Circuitry
- Add watchdog, I2C, pin control/GPIO, and Ethernet clocks on R-Car
V4H
- Add SDHI, Timer (CMT/TMU), and SPI (MSIOF) clocks on R-Car S4-8
- Add I2C clocks and resets on RZ/V2M
- Document clock support for the RZ/Five SoC
- mux-variant clock using the table variant to select parents
- clock controller for the rv1126 soc
- conversion of rk3128 to yaml and relicensing of the yaml bindings
to gpl2+MIT (following dt-binding guildelines)
- Exynos7885: add FSYS, TREX and MFC clock controllers
- Exynos850: add IS and AUD (audio) clock controllers with bindings
- ExynosAutov9: add FSYS clock controllers with bindings
- ExynosAutov9: correct clock IDs in bindings of Peric 0 and 1 clock
controllers, due to duplicated entries. This is an acceptable ABI
break: recently developed/added platform so without legacies, acked
by known users/developers
- ExynosAutov9: add few missing Peric 0/1 gates
- ExynosAutov9: correct register offsets of few Peric 0/1 clocks
- Minor code improvements (use of_device_get_match_data() helper,
code style)
- Add Krzysztof Kozlowski as co-maintainer of Samsung SoC clocks, as
he already maintainers that architecture/platform
- Keep Qualcomm GDSCs enabled when PWRSTS_RET flag is there, solving
retention issues during suspend of USB on Qualcomm sc7180/sc7280
and SC8280XP
- Qualcomm SM6115 and QCM2260 are moved to reuse PLL configuration
- Qualcomm SDM660 SDCC1 moved to floor clk ops
- Support for the APCS PLLs for Qualcomm IPQ8064, IPQ8074 and IPQ6018
was added/fixed
- The Qualcomm MSM8996 CPU clocks are updated with support for ACD
- Support for Qualcomm SDM670 GCC and RPMh clks was added
- Transition to parent_data, parent_hws and use of ARRAY_SIZE() for
num_parents was done for many Qualcomm SoCs
- Support for per-reset defined delay on Qualcomm was introduced"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (283 commits)
clk: qcom: gcc-sm6375: Ensure unsigned long type
clk: qcom: gcc-sm6375: Remove unused variables
clk: qcom: kpss-xcc: convert to parent data API
clk: introduce (devm_)hw_register_mux_parent_data_table API
clk: allow building lan966x as a module
clk: clk-xgene: simplify if-if to if-else
clk: ast2600: BCLK comes from EPLL
clk: clocking-wizard: Depend on HAS_IOMEM
clk: clocking-wizard: Use dev_err_probe() helper
clk: nxp: fix typo in comment
clk: pxa: add a check for the return value of kzalloc()
clk: vc5: Add support for IDT/Renesas VersaClock 5P49V6975
dt-bindings: clock: vc5: Add 5P49V6975
clk: mvebu: armada-37xx-tbg: Remove the unneeded result variable
clk: ti: dra7-atl: Fix reference leak in of_dra7_atl_clk_probe
clk: Renesas versaclock7 ccf device driver
dt-bindings: Renesas versaclock7 device tree bindings
clk: ti: Balance of_node_get() calls for of_find_node_by_name()
clk: imx: scu: fix memleak on platform_device_add() fails
clk: vc5: Use regmap_{set,clear}_bits() where appropriate
...
No error handling is performed when platform_device_add()
fails. Add error processing before return, and modified
the return value.
Fixes: 77d8f3068c ("clk: imx: scu: add two cells binding support")
Signed-off-by: Lin Yujun <linyujun809@huawei.com>
Link: https://lore.kernel.org/r/20220914033206.98046-1-linyujun809@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is build warning when CONFIG_OF is not selected.
>> drivers/clk/imx/clk-imx93.c:324:34: warning: 'imx93_clk_of_match'
>> defined but not used [-Wunused-const-variable=]
324 | static const struct of_device_id imx93_clk_of_match[] = {
| ^~~~~~~~~~~~~~~~~~
The driver only support DT table, no sense to use of_match_ptr.
Fixes: 24defbe194 ("clk: imx: add i.MX93 clk")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220830033137.4149542-3-peng.fan@oss.nxp.com
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is no dedicate parent clock for QSPI so SET_RATE_PARENT flag
should not be used. For instance, the default parent clock for QSPI is
pll2_bus, which is also the parent clock for quite a few modules, such
as MMDC, once GPMI NAND set clock rate for EDO5 mode can cause system
hang due to pll2_bus rate changed.
Fixes: f1541e15e3 ("clk: imx6sx: Switch to clk_hw based API")
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20220915150959.3646702-1-han.xu@nxp.com
Tested-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clk topology is as below:
bus_aon_root------>\ /--->SAI IPG
-->SAI LPCG gate-->
sai[x]_clk_root--->/ \--->SAI MCLK
So use shared count as i.MX93 MU_B gate.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220830033137.4149542-9-peng.fan@oss.nxp.com
The clk tree should be as:
bus_aon_root------>\ /--->MU1_B IP
-->MU_B gate-->
bus_wakeup_root--->/ \--->MU2_B IP
bus_aon_root------>\ /--->MU1_A IP
-->MU_A gate-->
bus_wakeup_root--->/ \--->MU2_A IP
So need use shared count gate. And linux use MU_B,
so set MU_A clk as CLK_IGNORE_UNUSED.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220830033137.4149542-8-peng.fan@oss.nxp.com
i.MX93 LPCG is different from i.MX8M CCGR. Although imx_clk_hw_gate4_flags
is used here, it not strictly match i.MX93. i.MX93 has such design:
- LPCG_DIRECT use BIT0 as on/off gate when LPCG_AUTHEN CPU_LPM is 0
- LPCG_LPM_CUR use BIT[2:0] as on/off gate when LPCG_AUTHEN CPU_LPM is 1
The current implementation suppose CPU_LPM is 0, and use LPCG_DIRECT
BIT[1:0] as on/off gate. Although BIT1 is touched, actually BIT1 is
reserved.
And imx_clk_hw_gate4_flags use mask 0x3 to determine whether the clk
is enabled or not, but i.MX93 LPCG only use BIT0 to control when CPU_LPM
is 0. So clk disabled unused during kernel boot not able to gate off
the unused clocks.
To match i.MX93 LPCG, introduce imx93_clk_gate.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220830033137.4149542-6-peng.fan@oss.nxp.com
The CCM ROOT AUTHEN register WHITE_LIST indicate:
Each bit in this field represent for one domain. Bit16~Bit31 represent
for DOMAIN0~DOMAIN15 respectively. Only corresponding bit of the domains
is set to 1 can change the registers of this Clock Root.
i.MX93 DID is 3, so if BIT(3 + WHITE_LIST_SHIFT) is 0, the clk should be
set to read only. To make the imx93_clk_composite_flags be reusable,
add a new parameter named did(domain id);
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220830033137.4149542-5-peng.fan@oss.nxp.com
i.MX93 CCM ROOT STAT register has a SLICE_BUSY bit:
indication for clock generation logic is applying new setting.
0b - Clock generation logic is not busy.
1b - Clock generation logic is applying new setting.
So when set parent/rate/gate, need check this bit.
Introduce specific ops to do the work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220830033137.4149542-4-peng.fan@oss.nxp.com
The enet_qos_root_clk takes sim_enet_root_clk as parent. When
registering enet_qos_root_clk, it will be put into clk orphan list,
because sim_enet_root_clk is not ready.
When sim_enet_root_clk is ready, clk_core_reparent_orphans_nolock will
set enet_qos_root_clk parent to sim_enet_root_clk.
Because CLK_OPS_PARENT_ENABLE is set, sim_enet_root_clk will be
enabled and disabled during the enet_qos_root_clk reparent phase.
All the above are correct. But with M7 booted early and using
enet, M7 enet feature will be broken, because clk driver probe phase
disable the needed clks, in case M7 firmware not configure
sim_enet_root_clk.
And tune the order would also save cpu cycles.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220815013428.476015-1-peng.fan@oss.nxp.com
Add the [484,498,445.3]MHz frequency support that will be used
by video subsystem on imx93.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220609132902.3504651-8-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
According to Reference Manual:
000b - Divide by 1
001b - Divide by 1
010b - Divide by 2
011b - Divide by 3
100b - Divide by 4
101b - Divide by 5
110b - Divide by 6
111b - Divide by 7
So only need increase rdiv by 1 when the register value is 0.
Fixes: 1b26cb8a77 ("clk: imx: support fracn gppll")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220609132902.3504651-7-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
The PLL parameters in rate table should be directly compared with
those read from PLL registers instead of the cooked ones.
Fixes: 1b26cb8a77 ("clk: imx: support fracn gppll")
Cc: Abel Vesa <abel.vesa@nxp.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220609132902.3504651-6-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
According to spec:
A value of 0 is disallowed and should not be programmed in this register
Fix to 1.
Fixes: 1b26cb8a77 ("clk: imx: support fracn gppll")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220609132902.3504651-5-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
For EDMA1 in AONMIX, its parent clock should be from cm33_root,
so Correct it.
Fixes: 24defbe194b65("clk: imx: add i.MX93 clk")
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220609132902.3504651-4-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
When debug, find after system boot up, all adc register operation
will trigger system hang, this is because the internal adc ipg
clock is gate off. In dts, only reference the IMX93_CLK_ADC1_GATE,
which is adc1, no one touch the adc_root, so adc_root will be gate
off automatically after system boot up.
Fixes: 24defbe194 ("clk: imx: add i.MX93 clk")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220609132902.3504651-2-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Here is the set of driver core changes for 5.19-rc1.
Note, I'm not really happy with this pull request as-is, see below for
details, but overall this is all good for everything but a small set of
systems, which we have a fix for already.
Lots of tiny driver core changes and cleanups happened this cycle,
but the two major things were:
- firmware_loader reorganization and additions including the
ability to have XZ compressed firmware images and the ability
for userspace to initiate the firmware load when it needs to,
instead of being always initiated by the kernel. FPGA devices
specifically want this ability to have their firmware changed
over the lifetime of the system boot, and this allows them to
work without having to come up with yet-another-custom-uapi
interface for loading firmware for them.
- physical location support added to sysfs so that devices that
know this information, can tell userspace where they are
located in a common way. Some ACPI devices already support
this today, and more bus types should support this in the
future.
Smaller changes included:
- driver_override api cleanups and fixes
- error path cleanups and fixes
- get_abi script fixes
- deferred probe timeout changes.
It's that last change that I'm the most worried about. It has been
reported to cause boot problems for a number of systems, and I have a
tested patch series that resolves this issue. But I didn't get it
merged into my tree before 5.18-final came out, so it has not gotten any
linux-next testing.
I'll send the fixup patches (there are 2) as a follow-on series to this
pull request if you want to take them directly, _OR_ I can just revert
the probe timeout changes and they can wait for the next -rc1 merge
cycle. Given that the fixes are tested, and pretty simple, I'm leaning
toward that choice. Sorry this all came at the end of the merge window,
I should have resolved this all 2 weeks ago, that's my fault as it was
in the middle of some travel for me.
All have been tested in linux-next for weeks, with no reported issues
other than the above-mentioned boot time outs.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnv/A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk/fACgvmenbo5HipqyHnOmTQlT50xQ9EYAn2eTq6ai
GkjLXBGNWOPBa5cU52qf
=yEi/
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core changes for 5.19-rc1.
Lots of tiny driver core changes and cleanups happened this cycle, but
the two major things are:
- firmware_loader reorganization and additions including the ability
to have XZ compressed firmware images and the ability for userspace
to initiate the firmware load when it needs to, instead of being
always initiated by the kernel. FPGA devices specifically want this
ability to have their firmware changed over the lifetime of the
system boot, and this allows them to work without having to come up
with yet-another-custom-uapi interface for loading firmware for
them.
- physical location support added to sysfs so that devices that know
this information, can tell userspace where they are located in a
common way. Some ACPI devices already support this today, and more
bus types should support this in the future.
Smaller changes include:
- driver_override api cleanups and fixes
- error path cleanups and fixes
- get_abi script fixes
- deferred probe timeout changes.
It's that last change that I'm the most worried about. It has been
reported to cause boot problems for a number of systems, and I have a
tested patch series that resolves this issue. But I didn't get it
merged into my tree before 5.18-final came out, so it has not gotten
any linux-next testing.
I'll send the fixup patches (there are 2) as a follow-on series to this
pull request.
All have been tested in linux-next for weeks, with no reported issues
other than the above-mentioned boot time-outs"
* tag 'driver-core-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
driver core: fix deadlock in __device_attach
kernfs: Separate kernfs_pr_cont_buf and rename_lock.
topology: Remove unused cpu_cluster_mask()
driver core: Extend deferred probe timeout on driver registration
MAINTAINERS: add Russ Weight as a firmware loader maintainer
driver: base: fix UAF when driver_attach failed
test_firmware: fix end of loop test in upload_read_show()
driver core: location: Add "back" as a possible output for panel
driver core: location: Free struct acpi_pld_info *pld
driver core: Add "*" wildcard support to driver_async_probe cmdline param
driver core: location: Check for allocations failure
arch_topology: Trace the update thermal pressure
kernfs: Rename kernfs_put_open_node to kernfs_unlink_open_file.
export: fix string handling of namespace in EXPORT_SYMBOL_NS
rpmsg: use local 'dev' variable
rpmsg: Fix calling device_lock() on non-initialized device
firmware_loader: describe 'module' parameter of firmware_upload_register()
firmware_loader: Move definitions from sysfs_upload.h to sysfs.h
firmware_loader: Fix configs for sysfs split
selftests: firmware: Add firmware upload selftests
...
According to reference mannual CCGR77(usb) sources from hsio_axi, fix
it.
Fixes: 9c140d9926 ("clk: imx: Add support for i.MX8MP clock driver")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220507125430.793287-1-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
clkout1 and clkout2 allow to supply clocks from the SoC to the board,
which is used by some board designs to provide reference clocks.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220427162131.3127303-1-l.stach@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1.
Also, we need to call pm_runtime_put_noidle() when pm_runtime_get_sync()
fails, so use pm_runtime_resume_and_get() instead. this function
will handle this.
Fixes: 78edeb0803 ("clk: imx: scu: add runtime pm support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220425011117.25093-1-linmq006@gmail.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
The driver_override field from platform driver should not be initialized
from static memory (string literal) because the core later kfree() it,
for example when driver_override is set via sysfs.
Use dedicated helper to set driver_override properly.
Fixes: 77d8f3068c ("clk: imx: scu: add two cells binding support")
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220419113435.246203-10-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add pixel clock for second LCDIFv3 interface. Both LCDIFv3 interfaces use
the same set of parent clock, so deduplicate imx8mp_media_disp1_pix_sels
into common imx8mp_media_disp_pix_sels and use it for both.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Abel Vesa <abel.vesa@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220313123949.207284-1-marex@denx.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
In __imx_clk_gpr_scu(), if imx_scu_clk_is_valid(rsrc_id) fails, then
`clk_node` which is allocated by kzalloc() is not properly released,
which may lead to memory leak.
So this patch added kfree(clk_node) on the above error path before
return ERR_PTR(-EINVAL).
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/tencent_27FF59903EE6AB5C0D0E6D0A8E7059A59007@qq.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
As the potential failure of the kcalloc(),
it should be better to check it in order to
avoid the dereference of the NULL pointer.
Fixes: 379c9a24cc ("clk: imx: Fix reparenting of UARTs not associated with stdout")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220310080257.1988412-1-jiasheng@iscas.ac.cn
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Add support for the General Purpose Timer (GPT) clocks on the i.MX8MN.
The i.MX8MN GPT IP block is the same as on the i.MX8MM, on which this
patch is based.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220317223600.175894-2-alvin@pqrs.dk
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
The SNVS moudule is not used only by the linux, it may also used
by other SW component is secure world. No sense to populate it
in linux, so remove it.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220310093404.236966-1-ping.bai@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
If mcore_booted is true, ignore the clk root gate registration and
this will simplify AMP clock management and avoid system hang unexpectly
especially Linux shutdown clk used by mcore.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220228124112.3974242-2-peng.fan@oss.nxp.com
[abelvesa@kernel.org: Removed if-case for when mcore_booted is true]
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Add mcore_booted boot parameter which could simplify AMP clock
management. To i.MX8M, there is CCM(clock control Module) to generate
clock root clock, anatop(analog PLL module) to generate PLL, and CCGR
(clock gating) to gate clocks to peripherals. As below:
anatop->ccm->ccgr->peripheral
Linux handles the clock management and the auxiliary core is under
control of Linux. Although there is per hardware domain control for CCGR
and CCM, auxiliary core normally only use CCGR hardware domain control
to avoid linux gate off the clk to peripherals and leave CCM ana anatop
to Linux.
Per NXP hardware design, because CCGR already support gate to
peripherals, and clk root gate power leakage is negligible. So
when in AMP case, we could not register the clk root gate.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220228124112.3974242-1-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
According to pll documentation, the 3rd pll ref clock should be
hdmi phy 27m clock, not dummy clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220225090002.2497057-3-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Most of the i.MX clock generic API is built by selecting MXC_CLK.
Without it, the i.MX93 clock driver will fail to build:
aarch64-linux-gnu-ld: drivers/clk/imx/clk-imx93.o:
in function `imx93_clocks_probe': clk-imx93.c:(.text+0xa8):
undefined reference to `imx_obtain_fixed_clk_hw'
So fix this by selecting MXC_CLK for the CLK_IMX93.
Fixes: 24defbe194 ("clk: imx: add i.MX93 clk")
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220315082446.3120850-1-abel.vesa@nxp.com
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There are two identical assignments of pll->base to the same value,
the second assignment is redundant and can be removed.
Cleans up cppcheck warning:
drivers/clk/imx/clk-sscg-pll.c:528:12: style: Variable 'pll->base' is
reassigned a value before the old one has been used. [redundantAssignment]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220303090508.1125175-1-colin.i.king@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The pll1443x PLL so far only supports rates from a rate table passed
during initialization. Calculating PLL settings dynamically helps audio
applications to get their desired rates, so support for this is added
in this patch.
The strategy to get to the PLL setting for a rate is:
- First try to only adjust kdiv which specifies the fractional part of the PLL.
This setting can be changed without glitches on the output and is therefore
preferred
- When that isn't possible then the rate table is searched for suitable rates,
so for standard rates the same settings are used as without this patch
- As a last resort the best settings are calculated dynamically
The code in this patch is based on patches from Adrian Alonso <adrian.alonso@nxp.com>
and Mads Bligaard Nielsen <bli@bang-olufsen.dk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220304125256.2125023-9-s.hauer@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Print all messages from within the pll14xx driver with a common
prefix using pr_fmt. No need to print function names anymore, so
drop them from the messages.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220304125256.2125023-8-s.hauer@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
clk_pll14xx_round_rate() returns the lowest rate by indexing into
the rate table with the variable i. i is actually pll->rate_count
as this is the value we come out of the loop with. Use pll->rate_count
explicitly to make it a bit more clear what is being done. While at
it fix a typo in the comment. No functional change.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220304125256.2125023-7-s.hauer@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
In clk_pll1443x_set_rate() 'tmp' is used for the content of different
registers which makes it a bit hard to follow. Use different variables
named after the registers to make it clearer. No functional change
intended.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220304125256.2125023-6-s.hauer@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
The PLL driver has support for two different PLLs: The pll1416x and
the pll1443x. The latter has support for an additional kdiv value.
recalc_rate can be the same calculation when kdiv is assumed to be zero
for the PLL which doesn't support that value.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220304125256.2125023-5-s.hauer@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Linux has these marvelous FIELD_GET/FIELD_PREP macros for easy access
to bitfields in registers. Use them and remove the now unused *_SHIFT
defines.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220304125256.2125023-4-s.hauer@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
The code tries to mask the bits in SDIV_MASK from 'tmp'. SDIV_MASK
already contains the shifted value, so shifting it again is wrong.
No functional change though as SDIV_SHIFT is zero.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220304125256.2125023-3-s.hauer@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
