Make it a struct cmd_header, since that's what it is, and clean up
the places that it's used.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This prevents us from trying to remove it when it didn't exist, in the
error case.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amazing what interesting things the compiler will tell you if you let it
know what types you expect to be passing around.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A simple callback which copies the response back into the
command buffer that was used to send the command to the
card. Will allow for direct command processing outside
the mega-switches in cmd.c and cmdresp.c.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move direct command handling through __lbs_cmd() over to using the
header as the first member of the command structure, and only define
the __lbs_cmd() callback in one place rather than 3. Convert boot2
version command to new usage.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to busy-wait, even if we did have a 100ms delay in the loop.
This makes it easier to support the new 'firmware ready' event which is
in the new firmware, too.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase the delay between issuing the RESET command and the usb reset,
and be prepared to discard more than one 'normal' packet from it before
it resets.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Total overkill to have an array when there's only one command in it.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware is always initialised before we register the netdevices.
It's not possible for pre_open_check() to fail.
One day we might try loading firmware in ->open(), but still it won't be
just a _check_, like this.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Define a macro that relieves the caller from having to use sizeof on
the command structure when calling lbs_cmd(), and move the prototype
of __lbs_cmd() to a new cmd.h file.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make it take struct lbs_private as argument; that's all it wants anyway,
and all callers were starting off from that. Don't wake the netif
queues, because those should be handled elsewhere. And sort out the
locking, with a big nasty warning for those who don't have the
driver_lock locked when they call it.
Oh, and fix if_cs.c to lock the driver_lock before calling it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be useful for letting callbacks do stuff like copying the
response into a buffer provided by the caller of lbs_cmd()
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, the display of subscribed events could be wrong.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need for these any more. We've collapsed all the unneeded nests of
functions which needed to keep track of which device the skb belonged to.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It replaces two lines of code. And even for those it has to make
inferences about things (i.e. which device) which the caller would have
just known.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function is only ever called if we're in rtap mode. So the bit in it
which is conditional on rtap mode seems a little superfluous.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The locking issues with TX, especially TX from multiple netdevs, get
_so_ much easier if you do it like this.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I was so busy cleaning up the failure modes that I accidentally forgot
to make sure we still free them in the success case. Oops.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix one of the barriers to simultaneous radiotap and normal operation --
stop misinterpreting the TX packets on the normal devices. We're also
going to have to clone the incoming skbs and feed them into both
devices, and there seem to be firmware problems with staying associated
too. But this is a reasonable start...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets us bring it up, because eth_validate_addr() succeeds instead
of returning -EINVAL. And finally monitor mode seems to (mostly) work.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There seems to be no point in doing it as an ieee80211 device instead of
a normal netdev, and when we override its ->priv and then call
free_ieee80211() it has a distressing tendency to crash horribly.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These wrappers only do two things.
Firstly, they set the frame type, which isn't necessary since
lbs_hard_start_xmit() gets to see which device it belongs to anyway.
Secondly, they return -EOPNOTSUPP if the device is in monitor mode.
Which is a strange thing to do and will provide nasty warnings from
qdisc_restart(). And lbs_hard_start_xmit() seems to have code to cope
with monitor mode anyway.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having merged the nest of functions into one, now we can clean it up and
fix the error handling, and the duplication -- and at least make a start
on the locking.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... where it can shortly be merged with lbs_process_tx()...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make a start on reducing the number of pointless nested functions,
starting with the StudlyCaps. No semantic changes (yet) -- we can sort
out the now-obvious discrepancy in the failure paths in a separate
commit.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was buggy as hell anyway, since it was just spewing packets at the
device when it wasn't necessarily ready for them (in the USB case, while
the URB was still busy).
We could probably do with a better way of flushing packets to the device
_immediately_, before we stick it back into sleep mode. But we can no
longer just dequeue packets directly, it seems.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It doesn't need to wait until no commands are pending anyway -- it only
needs to wait until the scan is finished.
We can hopefully find it something else to wait on too -- it's the only
user of the cmd_pending waitqueue.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also attempt some locking in lbs_host_to_card_done()
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There seems to be no reason for a separate structure; move it all
into struct lbs_private.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need this. We can use adapter->currenttxskb instead.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At least it doesn't oops when you attempt to read or write it now.
Only when you enable it and then later turn it off. And when it's
enabled I don't see how it actually works.
But one fewer oops is good, for now...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All existing code which sends commands is set up to have some function
called with the results, not to get data back. It's more versatile this
way, and providing it with a callback function which involves memcpy()
is hardly difficult.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also clean up the double setting/clearing of IW_ENCODE_DISABLED.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recently I found that that sparse by default doesn't endianness
checks. So I changed my compilation habit to be
make modules C=1 SUBDIRS=drivers/net/wireless/libertas
CHECKFLAGS="-D__CHECK_ENDIAN__"
so that I get the little-endian checks from sparse as well. That
showed up a good bunch of problems.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes the code that is used for scanning and makes it hopefully
easier to understand:
* move function into logical blocks
* create a bunch of lbs_scan_add_XXXX_tlv() functions, that
help to create the TLV parameter of CMD_802_11_SCAN
* all of them are now called from the much simpler lbs_do_scan()
* no **puserscancfg double-pointers :-)
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We read it from the card. We byte-swap it. We write it back to the card.
D'oh.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And the death of libertas_prepare_and_send_command() starts...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I wondered about junk bytes at the end when using "lbsdebug +hex +host"
until I noticed that firmware for the CF card sends my extranous bytes.
It says "I have 20 bytes", I take 20 bytes, but the last 8 bytes of this
are just data junk.
Also, in the new lbs_cmd() where was a size miscalulation
that made itself clear after fixing this bug.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't cast struct foo * to struct list_head *, it's safe only when
the list member is the first member of struct foo.
Also don't cast struct list_head * to struct foo *.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bad Holger. Always test on big-endian machines, if it's little-endian
you need to be swapping to/from.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise, lbs_process_rx_command() will take the new path for
lbs_cmd() responses, when it shouldn't.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is meaningless for non-USB devices and unimplemented in their
firmware. It's somewhat dubious for USB devices too, but that's a
different story.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This explains why we never noticed the corruption of checksums on
outgoing packets... we weren't actually checking them either.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using an arbitrary firmware command was actually very painful. One
had to change big switch() statements in cmd.c, cmdresp.c, add
structs to the big union in "struct cmd_ds_command" and add the
define for the CMD_802_11_xxx to the proper place.
With this function, this is now much easier. For now, it implements
a blocking (a.k.a. CMD_OPTION_WAITFORRSP) way where one deals directly
with command requests and response buffers. You can do everything in
one place:
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These functions were used in the old debugfs code for events, but
as this code is now gone, there's no need to export those functions.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was no code that ever did set this variable.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was no code that ever did set this flag.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As we move towards having this done by a state machine, start by having
a single 'stuff sent' function, which is called by if_usb/if_sdio/if_cs
after sending both data and commands.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is only needed for SNMP and key operations; it doesn't need to be
preserved outside that context.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* only shift eventcause once
* convert mac events to decimal, as this is what the firmware
manual uses in section 6.1, too
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the ability to specify channels to scan via debugfs
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the ability to specify number of probes via debugfs
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make two functions in the TX packet path emit
their debug messages with LBS_DEB_TX, not LBS_DEB_MAIN.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change debug output codes from LBS_DEB_JOIN to LBS_DEB_ASSOC
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves re-works the implementation of event subscription
via debugfs. For this:
* it tells cmd.c and cmdresp.c about CMD_802_11_SUBSCRIBE_EVENT
* removes lots of low-level cmd stuff from debugfs.c
* create unified functions to read/write snr, rssi, bcnmiss and
failcount
* introduces #define's for subscription event bitmask values
* add a function to search for a specific element in an IE
(a.k.a. TLV)
* add a function to find out the size of the TLV. This is needed
because lbs_prepare_and_send_command() has an argument for a
data buffer, but not for it's lengths and TLVs can be, by
definition, vary in size.
* fix a bug where it was not possible to disable an event
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New typedefs are usually frowned upon. This patch changes
libertas_adapter -> struct libertas_adapter
libertas_priv -> struct libertas_priv
While passing, make everything checkpatch.pl-clean that gets touches.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Requires firmware version 5.110.19.p0 or newer, available here:
http://dev.laptop.org/pub/firmware/libertas/
Signed-off-by: Ashish Shukla <ashishs@marvell.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The transmit and receive traffic as soon as the mesh interface is
brought up.
Test case 1: Bring up only the mesh interface and ping. No need for
any iwconfig commands on the main interface.
$ ifconfig msh0 192.168.5.3
$ iwconfig msh0 channel X
$ ping 192.168.5.2
If ping succeeds, PASS
Test case 2: Associate with the main interface, and turn off AP. Mesh
interface should not lose connectivity.
$ iwconfig eth0 mode managed essid "my_ssid"
$ ifconfig msh0 192.168.5.3
$ ping 192.168.5.2
<turn off access point>
If ping continues uninterrupted, PASS
This feature requires firmware version 5.110.19.p0 or newer, available
here: http://dev.laptop.org/pub/firmware/libertas/
Signed-off-by: Ashish Shukla <ashishs@marvell.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I think it was pretty obvious what fields in if_usb_driver are...
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Do not reset libertas devices upon module unload. We're unloading
the module, we're not killing off devices.
2) Instead, reset libertas devices inside if_usb_disconnect, as we're
killing off interfaces and so on.
3) Resetting via disconnect callback means we no longer need to keep
track of probed libertas devices; kill off that list (and its wonderful
lack of locking..), as well.
Drop a useless comment as well.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the debug output of all association stuff clearer by:
* adding some lbs_deb_enter()/lbs_deb_leave() calls
* printing the return level in one place
* lower-casing some string
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unifies the namespace of variables, functions defines
and structures. It does:
- rename libertas_XXX to lbs_XXX
- rename LIBERTAS_XXX to lbs_XXX
- rename wlan_XXX to lbs_XXX
- rename WLAN_XXX to LBS_XXX (but only those that were
defined in libertas-local *.h files, e.g. not defines
from net/ieee80211.h)
While passing, I fixed some checkpatch.pl errors too.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* use irq_handler_t where appropriate
* no need to use 'irq' function arg, its already stored in a data struct
* rename irq handler 'irq' argument to 'dummy', where the function
has been analyzed and proven not to use its first argument.
* remove always-false "dev_id == NULL" test from irq handlers
* remove pointless casts from void*
* declance: irq argument is not const
* add KERN_xxx printk prefix
* fix minor whitespace weirdness
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Move wlan_postpone_association_work() and wlan_cancel_association_work()
from a assoc.h file to the sole user, into wext.c.
Renamed those two functions to to libertas_XXX as well.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Identifiaction of another revision of 88w8385 in sdio mode.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
lbs_mac_event_disconnected() was called once and then never again
upon a hardware MAC event.
The reason was that the driver didn't clean the correct bit in the interrupt
cause register of the chip.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I'm not sure why it was doing this, and I'm not sure I _want_ to know
why. But calling it NETIF_F_DYNALLOC doesn't change the fact that the
kernel believes it to be NETIF_F_IPV6_CSUM, and that IPv6 communication
is hence buggered.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Properly account for queue commands, this fixes a problem reported
by Holger Schurig when using the debugfs interface.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incoming packets have to be aligned or the IP stack becomes upset.
Make sure to shift them two bytes to achieve this.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes for slow hardware.
Signed-off-by: Vitaly V. Bursov <vitalyvb@ukr.net>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the get-nickname wireless extension actually work. Before
this patch, I could do "iwconfig eth1 nick BLAH" but "iwconfig
eth1" would have still showed "MRVL-USB8388" to me. Hey, and that
was wrong anyway, I'm on a CF card, not on USB :-)
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-By: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes scripts/checkincludes.pl happy.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* make scan debug output cleaner
* change some LBS_DEB_ASSOC messages to LBS_DEB_SCAN, which is more correct
* move helper functions together
* print function return value in the tracing code at one central location
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-By: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes three "warning: Using plain integer as NULL pointer"
sparse warnings.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some versions of gcc replace strstr() calls with a single-character `needle'
parameter by strchr() behind our back. This causes a link error if strchr() is
defined as an inline function in <asm/string.h> (e.g. on m68k):
| drivers/built-in.o: In function `libertas_parse_chan':
| linux/drivers/net/wireless/libertas/debugfs.c:209: undefined reference to `strchr'
| drivers/built-in.o: In function `libertas_parse_ssid':
| linux/drivers/net/wireless/libertas/debugfs.c:260: undefined reference to `strchr'
Avoid this by explicitly calling strchr() instead.
Also include <linux/string.h>, because this file calls lots of str*() routines.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-By: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-By: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't write constants that are (per documentation and struct) u8
as 0x0001, use 0x01 instead. Also remove an useless cast.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-By: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 88w8385 chip, using SDIO interface and firmware release 5.0.11p0,
has problems when both unicast and multicast WPA keys are set in one
command. This patch ensures the keys are set independently.
The original author of this patch is Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixing memory alignment problems on the blackfin architecture (maybe on the
ARM also)
Signed-off-by: Vladimir Davydov <vladimir.davydov@promwad.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserve two bytes to align pointer to the IP header.
Signed-off-by: Vladimir Davydov <vladimir.davydov@promwad.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch fixes the tx transmit timeout problem, which is
caused by the interrupts being incorrectly check and masked. The patch
moves the interrupt masking code so that interrupts are enabled only
when the driver is registered and only disabled when the driver is
unregistered.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corrects a minor bug with priv->dnld_sent being set incorrectly in
if_cs_host_to_card.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wireless/libertas/if_cs.c: In function 'if_cs_prog_helper':
drivers/net/wireless/libertas/if_cs.c:462: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
drivers/net/wireless/libertas/if_cs.c: In function 'if_cs_prog_real':
drivers/net/wireless/libertas/if_cs.c:538: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
kmalloc() and friends return void*, no need to cast it.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Advertise support for 802.11g bitrates when starting adhoc
networks, not just 802.11b bitrates.
Signed-off-by: Brajesh Dave <brajeshd@marvell.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch strips away possible mess in regioncode (eg. on my card - 88W8305
chipset - I get 0x3031 instead of expected 0x0031 and as a result the driver
defaults to USA region which is obviously incorrect). Following patch fixes
the issue.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure that errors reported by the hardware layer is properly
handled. Otherwise commands tend to get stuck in limbo.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensures that any platform specific code that might live in libertas_reset_device
(for example, OLPC tells the EC to do a GPIO-toggled reset of the wireless
from libertas_reset_device) isn't called. Could be handled better by
interface-specific callbacks and a flag for "other hardware reset".
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves all firmware load responsibility into the interface-specific
code and gets rid of the firmware pointer in the generic card structure. It
also removes 3 fairly unecessary callbacks: hw_register_dev, hw_unregister_dev,
and hw_prog_firmware. It also makes the init sequence from interface
probe functions more logical, as there are paired add/remove and start/stop
calls into generic libertas code.
Because the USB driver code uses the same TX URB callback for both firmware
upload (where the generic libertas structure isn't initialized yet) and for
normal operation (where it is), some bits of USB code have to deal with
'priv' being NULL. All USB firmware upload bits have been changed to not
require 'priv' at all, but simply the USB card structure.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few fields being converted to the wrong sized type, and a few missed
endian conversions.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Describe the association response status code the firmware
returns, based on mail to libertas-dev from Ronak.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't trust the firmware to always send them at the right time,
ignore them when the driver thinks mesh autostart is disabled.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Boot2 version used to be hardcoded in the uploaded firmware,
this patch preserves the boot2 version before uploading firmware
and sends it to the firmware again on resume.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Push WEXT scan requests to a workqueue and have each partial scan queue
the next part, then only report results when the complete scan has finished.
Full scans don't go through the work queue.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver support for the monitor mode support that will be available in the next
OLPC 'bleeding edge' Marvell firmware release (most likely, 5.110.16.p2).
To activate monitor mode,
echo mode > /sys/class/net/{ethX,mshX}/device/libertas_rtap
where mode is the hex mask that specifies which frames to sniff (in short, 0x1
for data, 0x2 for all management but beacons, 0x4 for beacons). Any non zero
mode will activate the monitor mode, inhibiting transmission in ethX and mshX
interfaces and routing all the incoming traffic to a new rtapX interface that
will output the packets in 802.11+radiotap headers format.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
o SIOCGIWNAME is not designed to return the version number of the driver.
On the other hand, you are free to abuse SIOCGIWNICKN for that purpose.
o Don't attempt to fix the WE19/WE20 transition in the driver, because
your fixes are bogus, and redundant with the code in the kernel (you may
endup with +2, you can't read 32 char ESSID...).
o In SIOCSIWTXPOW, if you specified in iwrange that you want dBm, you
should only get dBm, which allow to reduce code bloat.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After loading the firmware, mesh autostart will be disabled. After that, the
user will still be able to enable or disable it at will. On suspend, it will be
always activated and later on resume it will go back to the state it had before
going to sleep.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CAPINFO_MASK changed on commits 981f187b and a091095b. Reverting to the original
value. Also move CAPINFO_MASK into the sole user, join.c. CAPINFO_MASK
should be in host CPU byte order; capability is converted to device
byte order elsewhere.
This fixes OLPC ticket #2161
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send association event to userspace when reassociating to the same
ad-hoc network, because it's still an association.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Purely cosmetic: this moves an lbs_deb_enter() to the proper place
and changes an erraneous lbs_deb_enter_args() into lbs_deb_leave_args()
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This value was parsed out, but then nowhere used ... except in
some debugfs output. I can't imagine anyone wanting to use this
value for anything real (as no other driver exports it), so
bye-bye.
Along this, made the columns of
/sys/kernel/debug/libertas_wireless/*/getscantable align again.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
scantype was initialized with CMD_SCAN_TYPE_ACTIVE, but there is no code
that would ever change it, so we can use that variable directly.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
scanmode was initialized with CMD_BSS_TYPE_ANY, but there is no code
that ever can store another value there, so it can go away.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
beaconperiod was initialized with MRVDRV_BEACON_INTERVAL, but there is
no code that would ever change it's value. We can use the define directly.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variable was initialized with 0 (false). There is no code that would
ever change it, so we can use the false-patch directly.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
listeninterval was initialized with MRVDRV_DEFAULT_LISTEN_INTERVAL, but
there exists that would ever change it. So we can use this define directly.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The value was computed, but then never used.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This varaible was initialized with 0 but there is no code that would ever
change it's value. So it can go away.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
multipledtim was initialized with MRVDRV_DEFAULT_MULTIPLE_DTIM and then
kept at that value, so we could use that define directly.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
locallisteninterval was initialized with 0, but there is no code that
changes it, rendering it rather useless.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No code ever initialized this variable, so it was 0 because of kzalloc().
But no other code changes it, making it rather useless.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Those two variables were initialized with some default values, but there
is no code that would ever change them. So we could use as well the defaults
directly.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No code uses the contents of this variable, so it can go.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The value of txrate was only set by a CMD_802_11_TX_RATE_QUERY command,
but there was no code in the driver that ever issued this command.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variable was initialized to 0 and nowhere else changed, so basically
the per-packet TX control wasn't used.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variable was initialized to 0 and nowhere else to anything
different.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The value 1 was assigned to it and there was nowhere any code
that would have changed that to 0.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was nowhere any code that used the values of those
variables.
This patch also removes two static functions that are now unused.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were just used in some debug output, but nowhere else.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for Marvell based 8385 compact flash cards.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
... and LBS_DEB_CMD for command execution. Also tidies misc
comments to give a consistent output.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... and LBS_DEB_CMD for command execution. Also tidies misc
comments to give a consistent output.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
types.h contains the same amount of CMD_RET_xxx and CMD_xxx definitions.
They contains the same info: the firmware command opcode and, when the
firmware sends back a result, the command opcode ORed with 0x8000.
Having the same data twice in the source code is redundant and can lead to
errors (e.g. if you update or delete only one instance). This patch removed
all CMD_RET_xxx definitions and introduces a simple CMD_RET() macro.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when you define LBS_DEB_HEX, you get every hex dump in the
whole driver, e.g. for LBS_DEB_CMD, LBS_DEB_RX, LBS_DEB_TX etc. This
patch makes sure that you only get the hexdump that you're interested in.
Renamed lbs_dbg_hex() into lbs_deb_hex(), like the other lbs_deb_XXX()
macros.
Made lbs_deb_hex() issue a line feed (and a new prompt) after 16 bytes.
As lbs_deb_hex() now prints the ":" after the prompt by itself, removed
the misc colons in the various *.c files.
lbs_deb_XXX() now print the debug category as well.
As lbs_deb_XXX() --- and especially lbs_deb_11d() --- now print the
category, I removed various "11D:" prefixes in 11d.c as well.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
echo 0 > /sys/class/net/mshX/autostart_enabled
This is supported from Marvell firmware version 5.110.16.p0 (to be released).
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is nowhere any place that set's this variable.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The CF/SDIO firmware doesn't support Mesh, so priv->mesh_dev is
NULL there. Protect all accesses.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Usually constants defined by #define are in ALL_UPPERCASE. This patch
fixes this.
I also shuffled the bits around so that they match the bit positions in the
host-interrupt-state register of the CF/SDIO card :-)
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some functions where declared in header files, but used only once. They are
now static functions.
After doing this, I found out that some functions weren't used at all. I
removed this dead code.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
adhoc_rates_b is only used locally, so make it static
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware download is quite different for different hardware. The SDIO and CF
cards have two flat files that need to be downloaded, whereas the USB driver
needs only one file, but with an internal structure.
The code that handles this (USB only) structured file is currently in fw.c.
This patch moves this code into if_usb.c. The remaining functions in fw.c
have not much to do with firmware, they are various card- and network-stack
initialisation functions. I've moved them into main.c.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused/duplicated fields and consolidate static data rate arrays,
for example the libertas_supported_rates[] and datarates[] arrays in
the bss_descriptor structure, and the libertas_supported_rates field
in the wlan_adapter structure.
Introduce libertas_fw_index_to_data_rate and libertas_data_rate_to_fw_index
functions and use them everywhere firmware requires a rate index rather
than a rate array.
The firmware requires the 4 basic rates to have the MSB set, but most
other stuff doesn't, like WEXT and mesh ioctls. Therefore, only set the MSB
on basic rates when pushing rate arrays to firmware instead of doing a ton
of (rate & 0x7f) everywhere.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not USB specific, so move it out of the USB interface code.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mistakently introduced by a previous patch to upper-case all command
constants.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for new mesh control knobs on firmware 5.220.11.p4:
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the thread.h abstractions and opencode kthread stuff
to make it clearer.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Missed when fixing mixed-case structure field names.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the only function in it to if_usb.c, which was its
only user anyway.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch, scanning with mshX interface will only return mesh networks. To
differentiate them, a specific mesh IE in beacons/probe responses is used. This
IE has been introduced in firmware release 5.110.14. Note:
Even though there can be at most a single mesh per channel, this scan might
return several networks in the same channel.
If all nodes in a mesh network are associated to an AP, they won't produce
beacons/probe responses, thus the network will not be listed. This will be fixed
in future firmware releases.
Scan on ethX interface is not filtered, so it will list both mesh and non-mesh
networks.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove struct IE_WPA and just use direct checking of the IE
bytes like ipw. Remove WLAN_802_11_VARIABLE_IEs because
it's unused.
Kill ieeetypes_elementid enum and just use MFIE_* from
ieee80211.h. Also use struct ieee80211_info_element for
scan buffer processing to simplify pointer usage.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It doesn't touch hardware and therefore doesn't need endian notations
either.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use standard BSS capability field constants from ieee80211.h.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes dead code introduced by
commit 90a42210f2 and spotted
by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... by removing an ill-conceived, useless line. Discovered by coverity.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove a header file that was ostensibly "removed" before, in commit
3ce40232.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't clobber the firmware's internal state machine by setting
ENABLE_RSN more than once during the 4-way handshake. Check what
the ENABLE_RSN status is and only set if it should be changed.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fold into wlan_scan_networks() and protect with debug defines.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With firmware 5.220.11.p5, this allows to specify the anycast addresses the
device will listen to.
The anycast address range is C0:27:C0:27:C0:XX where XX goes from 00 to 1F (or
0 to 31 in dec). The value to write on anycast_mask will specify which
addresses the device listens to. Bits in a 32 bit int are numbered from 0
(least significative bit) to 31. A specific address ending in YY will be
listened to if bit YY in the value is set to one.
Examples:
0x00000000 : do not listen to any anycast address
0xFFFFFFFF : listen to every anycast address from :00 to :1F
0x00000013 : listen to anycast addresses :00, :01 and :04
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This avoids channel mismatch between driver and firmware in case we change
channel while associated to an AP.
Signed-off-by: Luis Carlos Cobo Rus <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>