Current IRQ affinity interface does not provide a way to set affinity
for the IRQs that will be allocated/activated in the future.
This patch creates /proc/irq/default_smp_affinity that lets users set
default affinity mask for the newly allocated IRQs. Changing the default
does not affect affinity masks for the currently active IRQs, they
have to be changed explicitly.
Updated based on Paul J's comments and added some more documentation.
Signed-off-by: Max Krasnyansky <maxk@qualcomm.com>
Cc: pj@sgi.com
Cc: a.p.zijlstra@chello.nl
Cc: tglx@linutronix.de
Cc: rdunlap@xenotime.net
Cc: mingo@elte.hu
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdbts: Use HW breakpoints with CONFIG_DEBUG_RODATA
kgdb: use common ascii helpers and put_unaligned_be32 helper
In dynamic ftrace, the mcount function starts off pointing to a stub
function that just returns.
On start up, the call to the stub is modified to point to a "record_ip"
function. The job of the record_ip function is to add the function to
a pre-allocated hash list. If the function is already there, it simply is
ignored, otherwise it is added to the list.
Later, a ftraced daemon wakes up and calls kstop_machine if any functions
have been recorded, and changes the calls to the recorded functions to
a simple nop. If no functions were recorded, the daemon goes back to sleep.
The daemon wakes up once a second to see if it needs to update any newly
recorded functions into nops. Usually it does not, but if a lot of code
has been executed for the first time in the kernel, the ftraced daemon
will call kstop_machine to update those into nops.
The problem currently is that there's no way to stop the daemon from doing
this, and it can cause unneeded latencies (800us which for some is bothersome).
This patch adds a new file /debugfs/tracing/ftraced_enabled. If the daemon
is active, reading this will return "enabled\n" and "disabled\n" when the
daemon is not running. To disable the daemon, the user can echo "0" or
"disable" into this file, and "1" or "enable" to re-enable the daemon.
Since the daemon is used to convert the functions into nops to increase
the performance of the system, I also added that anytime something is
written into the ftraced_enabled file, kstop_machine will run if there
are new functions that have been detected that need to be converted.
This way the user can disable the daemon but still be able to control the
conversion of the mcount calls to nops by simply,
"echo 0 > /debugfs/tracing/ftraced_enabled"
when they need to do more conversions.
To see the number of converted functions:
"cat /debugfs/tracing/dyn_ftrace_total_info"
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tracing functions via ftrace which have a kretprobe installed on them, can produce misleading output in their trace logs. E.g, consider the correct trace of the following sequence:
do_IRQ()
{
~
irq_enter();
~
}
Trace log (sample):
<idle>-0 [00] 4154504455.781616: irq_enter <- do_IRQ
But if irq_enter() has a kretprobe installed on it, the return value stored on the stack at each invocation is modified to divert the return to a kprobe trampoline function called kretprobe_trampoline(). So with this the trace would (currently) look like:
<idle>-0 [00] 4154504455.781616: irq_enter <- kretprobe_trampoline
Now this is quite misleading to the end user, as it suggests something that didn't actually happen. So just to avoid such misinterpretations, the inlined patch aims to output such a log as:
<idle>-0 [00] 4154504455.781616: irq_enter <- [unknown/kretprobe'd]
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Acked-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Source code out there hard-codes a notion of what the
_LINUX_CAPABILITY_VERSION #define means in terms of the semantics of the
raw capability system calls capget() and capset(). Its unfortunate, but
true.
Since the confusing header file has been in a released kernel, there is
software that is erroneously using 64-bit capabilities with the semantics
of 32-bit compatibilities. These recently compiled programs may suffer
corruption of their memory when sys_getcap() overwrites more memory than
they are coded to expect, and the raising of added capabilities when using
sys_capset().
As such, this patch does a number of things to clean up the situation
for all. It
1. forces the _LINUX_CAPABILITY_VERSION define to always retain its
legacy value.
2. adopts a new #define strategy for the kernel's internal
implementation of the preferred magic.
3. deprecates v2 capability magic in favor of a new (v3) magic
number. The functionality of v3 is entirely equivalent to v2,
the only difference being that the v2 magic causes the kernel
to log a "deprecated" warning so the admin can find applications
that may be using v2 inappropriately.
[User space code continues to be encouraged to use the libcap API which
protects the application from details like this. libcap-2.10 is the first
to support v3 capabilities.]
Fixes issue reported in https://bugzilla.redhat.com/show_bug.cgi?id=447518.
Thanks to Bojan Smojver for the report.
[akpm@linux-foundation.org: s/depreciate/deprecate/g]
[akpm@linux-foundation.org: be robust about put_user size]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andrew G. Morgan <morgan@kernel.org>
Cc: Serge E. Hallyn <serue@us.ibm.com>
Cc: Bojan Smojver <bojan@rexursive.com>
Cc: stable@kernel.org
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Prevent short-running wakers of short-running threads from overloading a single
cpu via wakeup affinity, and wire up disconnected debug option.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make sched_clock_cpu() return 0 before it has been initialized and avoid
corrupting its state due to doing so.
This fixes the weird printk timestamp jump reported.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Yanmin Zhang reported:
Comparing with 2.6.25, volanoMark has big regression with kernel 2.6.26-rc1.
It's about 50% on my 8-core stoakley, 16-core tigerton, and Itanium Montecito.
With bisect, I located the following patch:
| 18d95a2832 is first bad commit
| commit 18d95a2832
| Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
| Date: Sat Apr 19 19:45:00 2008 +0200
|
| sched: fair-group: SMP-nice for group scheduling
Revert it so that we get v2.6.25 behavior.
Bisected-by: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The Coverity checker spotted a memleak introduced by commit
39106dcf85 (cpumask: use new cpus_scnprintf
function).
It seems the kfree() got lost between v2 and v3 of this patch...
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Mike Travis <travis@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Splice isn't always incrementing the ppos correctly, which broke
relay splice.
Signed-off-by: Tom Zanussi <zanussi@comcast.net>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Without console= arguments on the kernel command line, the first
console to register becomes enabled and the preferred console (the one
behind /dev/console). This is normally tty (assuming
CONFIG_VT_CONSOLE is enabled, which it commonly is).
This is okay as long tty is a useful console. But unless we have the
PV framebuffer, and it is enabled for this domain, tty0 in domU is
merely a dummy. In that case, we want the preferred console to be the
Xen console hvc0, and we want it without having to fiddle with the
kernel command line. Commit b8c2d3dfbc
did that for us.
Since we now have the PV framebuffer, we want to enable and prefer tty
again, but only when PVFB is enabled. But even then we still want to
enable the Xen console as well.
Problem: when tty registers, we can't yet know whether the PVFB is
enabled. By the time we can know (xenstore is up), the console setup
game is over.
Solution: enable console tty by default, but keep hvc as the preferred
console. Change the preferred console to tty when PVFB probes
successfully, unless we've been given console kernel parameters.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The variables dns and inc are not used, remove them.
Signed-off-by: Carlos R. Mafra <crmafra@gmail.com>
Cc: tglx@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
hres_timers_resume() warns if there appears to be more than one cpu
online. This warning makes sense when the suspend/resume mechanism
offlines all cpus but one during the suspend/resume process.
However, Xen suspend does not need to offline the other cpus; it
merely keeps them tied up in stop_machine() while the virtual machine
is suspended. The warning hres_timers_resume issues is therefore
spurious.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Hi Ingo/Steven,
Ftrace currently maintains an update count which includes false updates,
i.e, updates which failed. If anything, such failures should be tracked
by some separate variable, but this patch provides a minimal fix.
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: rostedt@goodmis.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Hi Steven,
I noticed that concurrent instances of ftrace_record_ip()
have a race between ftrace_hash list traversal during
ftrace_ip_in_hash() (before acquiring ftrace_shutdown_lock)
and ftrace_add_hash(). If it's so then this should fix it.
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: rostedt@goodmis.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The new work with converting the trace hooks over to markers broke the
command line recording of ftrace. This patch fixes it again.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While debugging latencies in the RT kernel, I found that it would be nice
to be able to filter away functions from the trace than just to filter
on functions.
I added a new interface to the debugfs tracing directory called
set_ftrace_notrace
When dynamic frace is enabled, this lets you filter away functions that will
not be recorded in the trace. It is similar to adding 'notrace' to those
functions but by doing it without recompiling the kernel.
Here's how set_ftrace_filter and set_ftrace_notrace interact. Remember, if
set_ftrace_filter is set, it removes all functions from the trace execpt for
those listed in the set_ftrace_filter. set_ftrace_notrace will prevent those
functions from being traced.
If you were to set one function in both set_ftrace_filter and
set_ftrace_notrace and that function was the same, then you would end up
with an empty trace.
the set of functions to trace is:
set_ftrace_filter == empty then
all functions not in set_ftrace_notrace
else
set of the set_ftrace_filter and not in set of set_ftrace_notrace.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Printing out new max latencies was fine for the old RT tracer. But for
mainline it is a bit messy. We also need to test if the run queue
is locked before we can do the print. This means that we may not be
printing out latencies if the run queue is locked on another CPU.
This produces inconsistencies in the output.
This patch simply removes the print altogether.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: pq@iki.fi
Cc: proski@gnu.org
Cc: sandmann@redhat.com
Cc: a.p.zijlstra@chello.nl
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds function tracing to the functions that are called
on the CPU of the task being traced.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: pq@iki.fi
Cc: proski@gnu.org
Cc: sandmann@redhat.com
Cc: a.p.zijlstra@chello.nl
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The check_pages function is called often enough that it can cause problems
with trace outputs or even bringing the system to a halt.
This patch limits the check_pages to the places that are most likely to
have problems. The check is made at the flip between the global array and
the max save array, as well as when the size of the buffers changes and
the self tests.
This patch also removes the BUG_ON from check_pages and replaces it with
a WARN_ON and disabling of the tracer.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: pq@iki.fi
Cc: proski@gnu.org
Cc: sandmann@redhat.com
Cc: a.p.zijlstra@chello.nl
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Based on Roland's patch. This approach was suggested by Austin Clements
from the very beginning, and then by Linus.
As Austin pointed out, the execing task can be killed by SI_TIMER signal
because exec flushes the signal handlers, but doesn't discard the pending
signals generated by posix timers. Perhaps not a bug, but people find this
surprising. See http://bugzilla.kernel.org/show_bug.cgi?id=10460
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Austin Clements <amdragon+kernelbugzilla@mit.edu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently sigqueue_free() removes sigqueue from list, but doesn't cancel the
pending signal. This is not consistent, the task should either receive the
"full" signal along with siginfo_t, or it shouldn't receive the signal at all.
Change sigqueue_free() to clear SIGQUEUE_PREALLOC but leave sigqueue on list
if it is queued.
This is a user-visible change. If the signal is blocked, it stays queued
after sys_timer_delete() until unblocked with the "stale" si_code/si_value,
and of course it is still counted wrt RLIMIT_SIGPENDING which also limits
the number of posix timers.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Austin Clements <amdragon+kernelbugzilla@mit.edu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As git-grep shows, open_softirq() is always called with the last argument
being NULL
block/blk-core.c: open_softirq(BLOCK_SOFTIRQ, blk_done_softirq, NULL);
kernel/hrtimer.c: open_softirq(HRTIMER_SOFTIRQ, run_hrtimer_softirq, NULL);
kernel/rcuclassic.c: open_softirq(RCU_SOFTIRQ, rcu_process_callbacks, NULL);
kernel/rcupreempt.c: open_softirq(RCU_SOFTIRQ, rcu_process_callbacks, NULL);
kernel/sched.c: open_softirq(SCHED_SOFTIRQ, run_rebalance_domains, NULL);
kernel/softirq.c: open_softirq(TASKLET_SOFTIRQ, tasklet_action, NULL);
kernel/softirq.c: open_softirq(HI_SOFTIRQ, tasklet_hi_action, NULL);
kernel/timer.c: open_softirq(TIMER_SOFTIRQ, run_timer_softirq, NULL);
net/core/dev.c: open_softirq(NET_TX_SOFTIRQ, net_tx_action, NULL);
net/core/dev.c: open_softirq(NET_RX_SOFTIRQ, net_rx_action, NULL);
This observation has already been made by Matthew Wilcox in June 2002
(http://www.cs.helsinki.fi/linux/linux-kernel/2002-25/0687.html)
"I notice that none of the current softirq routines use the data element
passed to them."
and the situation hasn't changed since them. So it appears we can safely
remove that extra argument to save 128 (54) bytes of kernel data (text).
Signed-off-by: Carlos R. Mafra <crmafra@ift.unesp.br>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
printk(KERN_ALERT "Danger Will Robinson!\nAlien Approaching!\n");
At present this will result in one message at ALERT level and one
at the current default message loglevel (e.g. WARNING). This is
non-intuitive.
Modify vprintk() to remember the message loglevel each time it
is specified and use it for subsequent lines of output which do
not specify one, within the same call to printk.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Restructure the logic of vprintk() so the processing of the leading
3 characters of each input line is in one place, regardless whether
printk_time is enabled. This makes the code smaller and easier to
understand.
size reduction in kernel/printk.o:
text data bss dec hex filename
6157 397 1049804 1056358 101e66 printk.o.before
6117 397 1049804 1056318 101e3e printk.o.after
and some style uncleanlinesses removed as well as a side-effect:
Before:
total: 19 errors, 22 warnings, 1340 lines checked
After:
total: 17 errors, 22 warnings, 1333 lines checked
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
console election: If some console happens to be registered first which does
not provide a tty binding (!console->device), it prevents that more suited
consoles which are registered later on can enter the candidate pool for
console_device(). This is observable with KGDB's console which may already
be registered (and exploited!) during early debugger connections, that is
before any regular console registration.
This patch fixes the issue by postponing the final, automated
preferred_console selection until someone with a non-NULL device handler
comes around.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Gerd Hoffmann <kraxel@suse.de>
Cc: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make printk_recursion_bug_msg static and drop printk prefix from recursion
variables.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is a slight change in the namespace cgroup subsystem api.
The change is that previously when cgroup_clone() was called (currently
only from the unshare path in ns_proxy cgroup, you'd get a new group named
"node_$pid" whereas now you'll get a group named after just your pid.)
The only users who would notice it are those who are using the ns_proxy
cgroup subsystem to auto-create cgroups when namespaces are unshared -
something of an experimental feature, which I think really needs more
complete container/namespace support in order to be useful. I suspect the
only users are Cedric and Serge, or maybe a few others on
containers@lists.linux-foundation.org. And in fact it would only be
noticed by the users who make the assumption about how the name is
generated, rather than getting it from the /proc/<pid>/cgroups file for
the process in question.
Whether the change is actually needed or not I'm fairly agnostic on, but I
guess it is more elegant to just use the pid as the new group name rather
than adding a fairly arbitrary "node_" prefix on the front.
[menage@google.com: provided changelog]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: "Paul Menage" <menage@google.com>
Cc: "Serge E. Hallyn" <serue@us.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If none of the switch cases match, the PR_SET_PDEATHSIG and
PR_SET_DUMPABLE cases of the switch statement will never write to local
variable `error'.
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com>
Cc: Andrew G. Morgan <morgan@kernel.org>
Acked-by: "Serge E. Hallyn" <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__exit_signal() does flush_sigqueue(tsk->pending) outside of ->siglock.
This can race with another thread doing sigqueue_free(), we can free the
same SIGQUEUE_PREALLOC sigqueue twice or corrupt the pending->list.
Note that even sys_exit_group() can trigger this race, not only
sys_timer_delete().
Move the callsite of flush_sigqueue(tsk->pending) under ->siglock.
This patch doesn't touch flush_sigqueue(->shared_pending) below, it is
called when there are no other threads which can play with signals, and
sigqueue_free() can't be used outside of our thread group.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's useful to detect which process is killed by RT watchdog.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Non-zero pid indicates the MMIO access originated in user space.
We do not catch that kind of accesses yet, so always print zero for now.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
another weekend, another patch. This should apply on top of my previous patch
from March 23rd.
Summary of changes:
- Print PCI device list in output header
- work around recursive probe hits on SMP
- refactor dis/arm_kmmio_fault_page() and add check for page levels
- remove un/reference_kmmio(), the die notifier hook is registered
permanently into the list
- explicitly check for single stepping in die notifier callback
I have tested this version on my UP Athlon64 desktop with Nouveau, and
SMP Core 2 Duo laptop with the proprietary nvidia driver. Both systems
are 64-bit. One previously unknown bug crept into daylight: the ftrace
framework's output routines print the first entry last after buffer has
wrapped around.
The most important regressions compared to non-ftrace mmiotrace at this
time are:
- failure of trace_pipe file
- illegal lines in output file
- unaware of losing data due to buffer full
Personally I'd like to see these three solved before submitting to
mainline. Other issues may come up once we know when we lose events.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
here is a patch that makes mmiotrace work almost well within the tracing
framework. The patch applies on top of my previous patch. I have my own
output formatting in place now.
Summary of changes:
- fix the NULL dereference that was due to not calling tracing_reset()
- add print_line() callback into struct tracer
- implement print_line() for mmiotrace, producing up-to-spec text
- add my output header, but that is not really called in the right place
- rewrote the main structs in mmiotrace
- added two new trace entry types: TRACE_MMIO_RW and TRACE_MMIO_MAP
- made some functions in trace.c non-static
- check current==NULL in tracing_generic_entry_update()
- fix(?) comparison in trace_seq_printf()
Things seem to work fine except a few issues. Markers (text lines injected
into mmiotrace log) are missing, I did not feel hacking them in before we
have variable length entries. My output header is printed only for 'trace'
file, but not 'trace_pipe'. For some reason, despite my quick fix,
iter->trace is NULL in print_trace_line() when called from 'trace_pipe'
file, which means I don't get proper output formatting.
I only tried by loading nouveau.ko, which just detects the card, and that
is traced fine. I didn't try further. Map, two reads and unmap. Works
perfectly.
I am missing the information about overflows, I'd prefer to have a
counter for lost events. I didn't try, but I guess currently there is no
way of knowning when it overflows?
So, not too far from being fully operational, it seems :-)
And looking at the diffstat, there also is some 700-900 lines of user space
code that just became obsolete.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On Sat, 22 Mar 2008 13:07:47 +0100
Ingo Molnar <mingo@elte.hu> wrote:
> > > i'd suggest the following: pull x86.git and sched-devel.git into a
> > > single tree [the two will combine without rejects]. Then try to add a
> > > kernel/tracing/trace_mmiotrace.c ftrace plugin. The trace_sysprof.c
> > > plugin might be a good example.
> >
> > I did this and now I have mmiotrace enabled/disabled via the tracing
> > framework (what do we call this, since ftrace is one of the tracers?).
>
> cool! could you send the patches for that? (even if they are not fully
> functional yet)
Patch attached in the end. Nice to see how much code disappeared. I tried
to mark all the features I had to break with XXX-comments.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch makes the stacktrace printout code \warn when the entries
pointer is unset rather than crashing when trying to access it in an
attempt to make it a bit more robust.
I was saving a stacktrace into an skb and forgot to copy it across skb
copies... I have since fixed the code, but it would have been easier
had the kernel not crashed in an interrupt.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Check that current->mm is non-NULL before attempting to trace the user
stack.
Also take depth of the kernel stack into account when comparing
against sample_max_depth.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
add kernel backtracing to the sysprof tracer.
change the format of the data, so that type=0 means
beginning of stack trace, 1 means kernel address, 2 means user
address, and 3 means end of trace.
EIP addresses are no longer distinguished from return addresses,
mostly because sysprof userspace doesn't make use of it. It may be
worthwhile adding this back in though, just in case it becomes
interesting.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
that's the only tested platform for now. If there's interest we
can make it generic easily.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now that ftrace is being ported to other architectures, it has become
apparent that DYNAMIC_FTRACE is dependent on whether or not that
architecture implements dynamic ftrace. FTRACE itself may be ported to
an architecture without porting dynamic ftrace.
This patch adds HAVE_DYNAMIC_FTRACE to allow architectures to port ftrace
without having to also port the dynamic aspect as well.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch removes the Makefile turd and uses the nice CFLAGS_REMOVE macro
in the kernel directory.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds full support for ftrace for PowerPC (both 64 and 32 bit).
This includes dynamic tracing and function filtering.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
David S. Miller noticed the following bug: the -pg instrumentation
function callback is named differently on each platform. On x86 it
is mcount, on sparc it is _mcount. So the export does not make sense
in kernel/trace/ftrace.c - move it to x86.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It causes unaligned access traps on platforms like sparc
(ftrace_page may be marked packed, but once we return
a dyn_ftrace sub-object from this array to another piece
of code, the "packed" part of the typing information doesn't
propagate).
But also, it didn't serve any purpose either. Even if packed,
on 64-bit or 32-bit, it didn't give us any more dyn_ftrace
entries per-page.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Porting ftrace to the marker infrastructure.
Don't need to chain to the wakeup tracer from the sched tracer, because markers
support multiple probes connected.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
CC: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Denys Vlasenko <vda.linux@googlemail.com> :
> Not in this patch, but I noticed:
>
> #define __trace_mark(name, call_private, format, args...) \
> do { \
> static const char __mstrtab_##name[] \
> __attribute__((section("__markers_strings"))) \
> = #name "\0" format; \
> static struct marker __mark_##name \
> __attribute__((section("__markers"), aligned(8))) = \
> { __mstrtab_##name, &__mstrtab_##name[sizeof(#name)], \
> 0, 0, marker_probe_cb, \
> { __mark_empty_function, NULL}, NULL }; \
> __mark_check_format(format, ## args); \
> if (unlikely(__mark_##name.state)) { \
> (*__mark_##name.call) \
> (&__mark_##name, call_private, \
> format, ## args); \
> } \
> } while (0)
>
> In this call:
>
> (*__mark_##name.call) \
> (&__mark_##name, call_private, \
> format, ## args); \
>
> you make gcc allocate duplicate format string. You can use
> &__mstrtab_##name[sizeof(#name)] instead since it holds the same string,
> or drop ", format," above and "const char *fmt" from here:
>
> void (*call)(const struct marker *mdata, /* Probe wrapper */
> void *call_private, const char *fmt, ...);
>
> since mdata->format is the same and all callees which need it can take it there.
Very good point. I actually thought about dropping it, since it would
remove an unnecessary argument from the stack. And actually, since I now
have the marker_probe_cb sitting between the marker site and the
callbacks, there is no API change required. Thanks :)
Mathieu
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
CC: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently there is no protection from the root user to use up all of
memory for trace buffers. If the root user allocates too many entries,
the OOM killer might start kill off all tasks.
This patch adds an algorith to check the following condition:
pages_requested > (freeable_memory + current_trace_buffer_pages) / 4
If the above is met then the allocation fails. The above prevents more
than 1/4th of freeable memory from being used by trace buffers.
To determine the freeable_memory, I made determine_dirtyable_memory in
mm/page-writeback.c global.
Special thanks goes to Peter Zijlstra for suggesting the above calculation.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Refactor code from tracing_read_pipe() and create trace_seq_to_user().
Moved trace_seq_reset() call before iter->trace->read() call so that
when all leftover data is returned, trace_seq is reset automatically.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Due to debug hooks in the kernel that can change the way smp_processor_id
works, use raw_smp_processor_id in mcount called functions (namely
ftrace_record_ip). Currently we annotate most debug functions from calling
mcount, but we should not rely on that to prevent kernel lockups.
This patch uses the raw_smp_processor_id to prevent a recusive crash
that can happen if a debug hook in smp_processor_id calls mcount.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In resetting the iterator in read_pipe, the reset of pos was
postitioned in the wrong location with respect to the memset
operation. The current code sets pos, incorrectly, to zero.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds a method for open_pipe and open_read to the pluggins
so that they can add a header to the trace pipe call.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch sets up the infrastructure to record overruns of the tracing
buffer.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In cleaning up of the sched_switch code, the function trace recording
of task comms was removed. This patch adds back the recording of comms
for function trace. The output of ftrace now has the task comm instead
of <...>.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is first installment of adding documentation to the ftrace.
Expect many more patches of this kind in the near future.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently ftrace allocates a trace buffer for every possible CPU.
Work is being done to change it to only online CPUs and add hooks
to hotplug CPUS.
This patch lays out the infrastructure for such a change.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Andrew Morton suggested using strict_strtoul over simple_strtoul.
This patch replaces them in ftrace.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Andrew Morton mentioned some clean ups that should be done to ftrace.
This patch does some of the simple clean ups.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
With the introduction of ftrace, it is possible to recurse into
the lockdep functions via the mcount call. To prevent possible
lockups, updating the lockdep_recursion counter on grabbing the internal
lockdep_lock should prevent deadlocks.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds /debug/tracing/trace_entries that allows users to
see as well as modify the number of trace entries the buffers hold.
The number of entries only increments in ENTRIES_PER_PAGE which is
calculated by the size of an entry with the number of entries that
can fit in a page. The user does not need to use an exact size, but
the entries will be rounded to one of the increments.
Trying to set the entries to 0 will return with -EINVAL.
To avoid race conditions, the modification of the buffer size can only
be done when tracing is completely disabled (current_tracer == none).
A info message will be printed if a user tries to modify the buffer size
when not set to none.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The wakeup selftest used an internal API for setting the test task priority.
This patch fixes it to use the proper API for performing such a task.
Thanks goes to Randy Dunlap for pointing out this build failure.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch implements "NONBLOCK" for trace_pipe. If the trace_pipe is opened
with O_NONBLOCK, then the trace_pipe read will not block when buffer is empty.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Break out of while loop with EOF when the current_trace changes.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The trace iterator is reset in the read. We still need to restore the tracer
that the trace_pipe was opened with.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We expect things like "cat" to block on reads to trace_pipe. That's what
trace_pipe is for.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The conversion of task states to a character in the sched_switch tracer (part
of latency tracer infrastructure), seems to be incorrect. We currently do it
by indexing into the state_to_char array using the state value. The state
values do not map directly into the array index and are thus incorrect. The
following patch addresses this issue. This is also what is being done even
in the show_task() routine in kernel/sched.c
The patch has been compile and run tested.
Signed-off-by: Ankita Garg <ankita@in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is a slight race condition in the selftest where the max update
of the wakeup and irqs/preemption off tests can be doing a max update as
the buffers are being tested. If this happens the system can crash with
a GPF.
This patch adds the max update spinlock around the checking of the
buffers to prevent such a race.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If the trace output changes on reading the trace files, there is a chance
that the start function will return NULL. If the start function of a sequence
returns NULL the stop equivalent is not called. In this case, all locks
that are taken must be released even if they are released in the stop function.
This patch fixes a case that a mutex was not released on return of NULL
in the start sequence function.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When dynamic ftrace fails and sets itself disabled, the ftraced daemon
will go back to sleep everytime it wakes up. The setting of the
ftraced state to UNINTERRUPTIBLE is skipped in this process, and the
daemon takes up 100% of the CPU. This patch makes sure the ftraced daemon
sets itself to UNINTERRUPTIBLE in that loop.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch removes the "notrace" annotation from lockdep and adds the debugging
files in the kernel director to those that should not be compiled with
"-pg" mcount tracing.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Lock debugging enabled cause huge performance problems for tracing. Having
the lock verification happening for every function that is called
because mcount calls spin_lock can cripple the system.
This patch converts the spin_locks used by ftrace into raw_spin_locks.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch changes the use of __get_cpu_var to explicitly calling
raw_smp_processor_id and using the per_cpu() macro. On some debug
configurations, the use of __get_cpu_var may cause ftrace to trigger
and this can cause problems with the irqsoff tracing.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
With the adding of the configuration changes in the Makefile to prevent
tracing of functions in the ftrace code, all tracing of all the ftrace
code has been removed. Unfortunately, one of the selftests, relied on
a function to be traced. With the new change, the function was no longer
traced and the test failed.
This patch separates out the test function into its own file so that
we can add the "-pg" flag to the compilation of that function and the
adding of the mcount call to that function.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The selftest validation code checks for valid entries in the trace buffer.
TRACE_STACK and TRACE_SPECIAL have been added to the code but not to
the validator. This patch adds the two to prevent them from flagging a
failure in the selftest.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
printk called from wakeup critical timings and irqs off can
cause deadlocks since printk might do a wakeup itself. If the
call to printk happens with the runqueue lock held, it can
deadlock.
This patch protects the printk from being called in trace irqs off
with a test to see if the runqueue for the current CPU is locked.
If it is locked, the printk is skipped.
The wakeup always holds the runqueue lock, so the printk is
simply removed.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
trace_function is called by mcount and calling wake_up from that
can have unpredictable results. This patch removes the wakeup from
trace_function.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
now that we have a kbuild method for notrace, no need to pollute the
C code with the annotations.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
PowerPC is very fragile when it comes to use of function names
and function addresses. ftrace needs to either use all function
addresses or function names (i.e. my_func as suppose to &my_func).
This patch chooses to use the names and not the addresses, and
makes ftrace consistent.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
A new check was added in the ftrace function that wont trace if the CPU
trace buffer is disabled. Unfortunately, other tracers used ftrace() to
write to the buffer after they disabled it. The new disable check makes
these calls into a nop.
This patch changes the __ftrace that is called without the check into a
new api for the other tracers to use, called "trace_function". The other
tracers use this interface instead when the trace CPU buffer is already
disabled.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
no need to backmerge, only affects ftrace-enabled kernels. (which is
not the default)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch is the correct way to have tracing enabled by default.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since ftrace touches practically every function. If we detect any
anomaly, we want to fully disable ftrace. This patch adds code
to try shutdown ftrace as much as possible without doing any more
harm is something is detected not quite correct.
This only kills ftrace, this patch does have checks for other parts of
the tracer (irqsoff, wakeup, etc.).
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The ftrace dynamic function update allocates a record to store the
instruction pointers that are being modified. If the modified
instruction pointer fails to update, then the record is marked as
failed and nothing more is done.
Worse, if the modification fails, but the record ip function is still
called, it will allocate a new record and try again. In just a matter
of time, will this cause a serious memory leak and crash the system.
This patch plugs this memory leak. When a record fails, it is
included back into the pool of records to be used. Now a record may
fail over and over again, but the number of allocated records will
not increase.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some fixes for better output with the trace pipe.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
implement globally synchronized, fast and scalable time source for tracing.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
we can hold all cpu trace buffer locks at once - put each into a
separate lock class.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch creates a file called trace_pipe in the tracing
debug directory. This file is a consumer of the trace buffers.
This means that reads of this file consumes the entries from
the trace buffers so that they will not be read a second time,
as contrast to the static buffers latency_trace and trace.
Reading from the trace_pipe will remove the entries from trace
and latency_trace too.
The advantage that trace_pipe has is that it can record live
traces. It will block when there is nothing in the buffer,
and read the entries as they are entered. An EOF happens when
tracing is disabled (tracing_enabled = 0).
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Later patches will need to print the same things as the seq output
does. But those outputs will not use the seq utility. This patch
adds a buffer to the iterator, that can be used by either the
seq utility or other output.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch changes the way the CPU trace buffers are handled.
Instead of always starting from the trace page head, the logic
is changed to a producer consumer logic. This allows for the
buffers to be drained while they are alive.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The tests may leave stuff in the buffers. This resets the buffers
after each test is run. If a test fails, it does not reset the
buffer to avoid touching a buffer that is corrupted.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If the trace buffer is detected to be corrupted, then we
disable all tracers.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
fix time offset calculations and ordering, plus make code more consistent.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds a startup self test on dynamic code modification
and filters. The test filters on a specific function, makes sure that
no other function is traced, exectutes the function, then makes sure that
the function is traced.
This patch also fixes a slight bug with the ftrace selftest, where
tracer_enabled was not being set.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch fixes some bugs to the updating of the max trace that
was caused by implementing the new buffering.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Using raw_local_irq_save/restore confuses lockdep.
It's fine to use the normal ones.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add notrace annotations to lockdep to keep ftrace from causing
recursive problems with lock tracing and debugging.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The irqsoff function tracer did a __get_cpu_var to determine
if it should trace the function or not. The problem is that
__get_cpu_var can preempt between getting the CPU and reading
the cpu variable. This means that the cpu variable that is
being read is not from the cpu being run on.
At worst, this can give a false positive, where we trace the
function when we should not. It will never give a false negative
since we only want to trace when interrupts are disabled
and we never preempt when they are.
This fix adds a check after reading the irq flags to only
trace if the interrupts are actually disabled. It also changes
the reading of the cpu variable to use a raw_smp_processor_id
since we now don't care if we preempt. We still catch that fact.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Allocating large buffers for the tracer may fail easily.
This patch converts the buffer from a large ordered allocation
to single pages. It uses the struct page LRU field to link the
pages together.
Later patches may also implement dynamic increasing and decreasing
of the trace buffers.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds two files to the debugfs system:
/debugfs/tracing/available_filter_functions
and
/debugfs/tracing/set_ftrace_filter
The available_filter_functions lists all functions that has been
recorded by the ftraced that has called the ftrace_record_ip function.
This is to allow users to see what functions have been converted
to nops and can be enabled for tracing.
To enable functions, simply echo the names (whitespace delimited)
into set_ftrace_filter. Simple wildcards are also allowed.
echo 'scheduler' > /debugfs/tracing/set_ftrace_filter
Will have only the scheduler be activated when tracing is enabled.
echo 'sched_*' > /debugfs/tracing/set_ftrace_filter
Will have only the functions starting with 'sched_' be activated.
echo '*lock' > /debugfs/tracing/set_ftrace_filter
Will have only functions ending with 'lock' be activated.
echo '*lock*' > /debugfs/tracing/set_ftrace_filter
Will have only functions with 'lock' in its name be activated.
Note: 'sched*lock' will not work. The only wildcards that are
allowed is an asterisk and the beginning and or end of the string
passed in.
Multiple names can be passed in with whitespace delimited:
echo 'scheduler *lock *acpi*' > /debugfs/tracing/set_ftrace_filter
is also the same as:
echo 'scheduler' > /debugfs/tracing/set_ftrace_filter
echo '*lock' >> /debugfs/tracing/set_ftrace_filter
echo '*acpi*' >> /debugfs/tracing/set_ftrace_filter
Appending does just that. It appends to the list.
To disable all filters simply echo an empty line in:
echo > /debugfs/tracing/set_ftrace_filter
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch replaces the indirect call to the mcount function
pointer with a direct call that will be patched by the
dynamic ftrace routines.
On boot up, the mcount function calls the ftace_stub function.
When the dynamic ftrace code is initialized, the ftrace_stub
is replaced with a call to the ftrace_record_ip, which records
the instruction pointers of the locations that call it.
Later, the ftraced daemon will call kstop_machine and patch all
the locations to nops.
When a ftrace is enabled, the original calls to mcount will now
be set top call ftrace_caller, which will do a direct call
to the registered ftrace function. This direct call is also patched
when the function that should be called is updated.
All patching is performed by a kstop_machine routine to prevent any
type of race conditions that is associated with modifying code
on the fly.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch moves the memory management of the ftrace
records out of the arch code and into the generic code
making the arch code simpler.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds back the sysctl ftrace_enabled. This time it is
defaulted to on, if DYNAMIC_FTRACE is configured. When ftrace_enabled
is disabled, the ftrace function is set to the stub return.
If DYNAMIC_FTRACE is also configured, on ftrace_enabled = 0,
the registered ftrace functions will all be set to jmps, but no more
new calls to ftrace recording (used to find the ftrace calling sites)
will be called.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds a feature to dynamically replace the ftrace code
with the jmps to allow a kernel with ftrace configured to run
as fast as it can without it configured.
The way this works, is on bootup (if ftrace is enabled), a ftrace
function is registered to record the instruction pointer of all
places that call the function.
Later, if there's still any code to patch, a kthread is awoken
(rate limited to at most once a second) that performs a stop_machine,
and replaces all the code that was called with a jmp over the call
to ftrace. It only replaces what was found the previous time. Typically
the system reaches equilibrium quickly after bootup and there's no code
patching needed at all.
e.g.
call ftrace /* 5 bytes */
is replaced with
jmp 3f /* jmp is 2 bytes and we jump 3 forward */
3:
When we want to enable ftrace for function tracing, the IP recording
is removed, and stop_machine is called again to replace all the locations
of that were recorded back to the call of ftrace. When it is disabled,
we replace the code back to the jmp.
Allocation is done by the kthread. If the ftrace recording function is
called, and we don't have any record slots available, then we simply
skip that call. Once a second a new page (if needed) is allocated for
recording new ftrace function calls. A large batch is allocated at
boot up to get most of the calls there.
Because we do this via stop_machine, we don't have to worry about another
CPU executing a ftrace call as we modify it. But we do need to worry
about NMI's so all functions that might be called via nmi must be
annotated with notrace_nmi. When this code is configured in, the NMI code
will not call notrace.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add preempt off timings. A lot of kernel core code is taken from the RT patch
latency trace that was written by Ingo Molnar.
This adds "preemptoff" and "preemptirqsoff" to /debugfs/tracing/available_tracers
Now instead of just tracing irqs off, preemption off can be selected
to be recorded.
When this is selected, it shares the same files as irqs off timings.
One can either trace preemption off, irqs off, or one or the other off.
By echoing "preemptoff" into /debugfs/tracing/current_tracer, recording
of preempt off only is performed. "irqsoff" will only record the time
irqs are disabled, but "preemptirqsoff" will take the total time irqs
or preemption are disabled. Runtime switching of these options is now
supported by simpling echoing in the appropriate trace name into
/debugfs/tracing/current_tracer.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds the latency tracer infrastructure. This patch
does not add anything that will select and turn it on, but will
be used by later patches.
If it were to be compiled, it would add the following files
to the debugfs:
The root tracing directory:
/debugfs/tracing/
This patch also adds the following files:
available_tracers
list of available tracers. Currently no tracers are
available. Looking into this file only shows
"none" which is used to unregister all tracers.
current_tracer
The trace that is currently active. Empty on start up.
To switch to a tracer simply echo one of the tracers that
are listed in available_tracers:
example: (used with later patches)
echo function > /debugfs/tracing/current_tracer
To disable the tracer:
echo disable > /debugfs/tracing/current_tracer
tracing_enabled
echoing "1" into this file starts the ftrace function tracing
(if sysctl kernel.ftrace_enabled=1)
echoing "0" turns it off.
latency_trace
This file is readonly and holds the result of the trace.
trace
This file outputs a easier to read version of the trace.
iter_ctrl
Controls the way the output of traces look.
So far there's two controls:
echoing in "symonly" will only show the kallsyms variables
without the addresses (if kallsyms was configured)
echoing in "verbose" will change the output to show
a lot more data, but not very easy to understand by
humans.
echoing in "nosymonly" turns off symonly.
echoing in "noverbose" turns off verbose.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If CONFIG_FTRACE is selected and /proc/sys/kernel/ftrace_enabled is
set to a non-zero value the ftrace routine will be called everytime
we enter a kernel function that is not marked with the "notrace"
attribute.
The ftrace routine will then call a registered function if a function
happens to be registered.
[ This code has been highly hacked by Steven Rostedt and Ingo Molnar,
so don't blame Arnaldo for all of this ;-) ]
Update:
It is now possible to register more than one ftrace function.
If only one ftrace function is registered, that will be the
function that ftrace calls directly. If more than one function
is registered, then ftrace will call a function that will loop
through the functions to call.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The tracer wants to be able to convert the state number
into a user visible character. This patch pulls that conversion
string out the scheduler into the header. This way if it were to
ever change, other parts of the kernel will know.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
add 3 lightweight callbacks to the tracer backend.
zero impact if tracing is turned off.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On kvm I have seen some rare hangs in stop_machine when I used more guest
cpus than hosts cpus. e.g. 32 guest cpus on 1 host cpu triggered the
hang quite often. I could also reproduce the problem on a 4 way z/VM host with
a 64 way guest.
It turned out that the guest was consuming all available cpus mostly for
spinning on scheduler locks like rq->lock. This is expected as the threads are
calling yield all the time.
The problem is now, that the host scheduling decisings together with the guest
scheduling decisions and spinlocks not being fair managed to create an
interesting scenario similar to a live lock. (Sometimes the hang resolved
itself after some minutes)
Changing stop_machine to yield the cpu to the hypervisor when yielding inside
the guest fixed the problem for me. While I am not completely happy with this
patch, I think it causes no harm and it really improves the situation for me.
I used cpu_relax for yielding to the hypervisor, does that work on all
architectures?
p.s.: If you want to reproduce the problem, cpu hotplug and kprobes use
stop_machine_run and both triggered the problem after some retries.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
CC: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The comment was correct -- need to make the code match the comment.
Without this patch, if a CPU goes dynticks idle (and stays there forever)
in just the right phase of preemptible-RCU grace-period processing,
grace periods stall. The offending sequence of events (courtesy
of Promela/spin, at least after I got the liveness criterion coded
correctly...) is as follows:
o CPU 0 is in dynticks-idle mode. Its dynticks_progress_counter
is (say) 10.
o CPU 0 takes an interrupt, so rcu_irq_enter() increments CPU 0's
dynticks_progress_counter to 11.
o CPU 1 is doing RCU grace-period processing in rcu_try_flip_idle(),
sees rcu_pending(), so invokes dyntick_save_progress_counter(),
which in turn takes a snapshot of CPU 0's dynticks_progress_counter
into CPU 0's rcu_dyntick_snapshot -- now set to 11. CPU 1 then
updates the RCU grace-period state to rcu_try_flip_waitack().
o CPU 0 returns from its interrupt, so rcu_irq_exit() increments
CPU 0's dynticks_progress_counter to 12.
o CPU 1 later invokes rcu_try_flip_waitack(), which notices that
CPU 0 has not yet responded, and hence in turn invokes
rcu_try_flip_waitack_needed(). This function examines the
state of CPU 0's dynticks_progress_counter and rcu_dyntick_snapshot
variables, which it copies to curr (== 12) and snap (== 11),
respectively.
Because curr!=snap, the first condition fails.
Because curr-snap is only 1 and snap is odd, the second
condition fails.
rcu_try_flip_waitack_needed() therefore incorrectly concludes
that it must wait for CPU 0 to explicitly acknowledge the
counter flip.
o CPU 0 remains forever in dynticks-idle mode, never taking
any more hardware interrupts or any NMIs, and never running
any more tasks. (Of course, -something- will usually eventually
happen, which might be why we haven't seen this one in the
wild. Still should be fixed!)
Therefore the grace period never ends. Fix is to make the code match
the comment, as shown below. With this fix, the above scenario
would be satisfied with curr being even, and allow the grace period
to proceed.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Josh Triplett <josh@kernel.org>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move rcu-protected lists from list.h into a new header file rculist.h.
This is done because list are a very used primitive structure all over the
kernel and it's currently impossible to include other header files in this
list.h without creating some circular dependencies.
For example, list.h implements rcu-protected list and uses rcu_dereference()
without including rcupdate.h. It actually compiles because users of
rcu_dereference() are macros. Others RCU functions could be used too but
aren't probably because of this.
Therefore this patch creates rculist.h which includes rcupdates without to
many changes/troubles.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Josh Triplett <josh@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add entry to rcu_torture_ops allowing the correct barrier function to
be used upon exit from rcutorture. Also add torture options for the
new call_rcu_sched() API.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add rcu_barrier_sched() and rcu_barrier_bh(). With these in place,
rcutorture no longer gives the occasional oops when repeatedly starting
and stopping torturing rcu_bh. Also adds the API needed to flush out
pre-existing call_rcu_sched() callbacks.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add comments to the logic that infers quiescent states when interrupting
from either user mode or the idle loop. Also add a memory barrier: it
appears that James Huang was in fact onto something, as the scheduler
is much less synchronization happy than it once was, so we can no longer
rely on its memory barriers in all cases.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reported-by: James Huang <jamesclhuang@yahoo.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fourth cut of patch to provide the call_rcu_sched(). This is again to
synchronize_sched() as call_rcu() is to synchronize_rcu().
Should be fine for experimental and -rt use, but not ready for inclusion.
With some luck, I will be able to tell Andrew to come out of hiding on
the next round.
Passes multi-day rcutorture sessions with concurrent CPU hotplugging.
Fixes since the first version include a bug that could result in
indefinite blocking (spotted by Gautham Shenoy), better resiliency
against CPU-hotplug operations, and other minor fixes.
Fixes since the second version include reworking grace-period detection
to avoid deadlocks that could happen when running concurrently with
CPU hotplug, adding Mathieu's fix to avoid the softlockup messages,
as well as Mathieu's fix to allow use earlier in boot.
Fixes since the third version include a wrong-CPU bug spotted by
Andrew, getting rid of the obsolete synchronize_kernel API that somehow
snuck back in, merging spin_unlock() and local_irq_restore() in a
few places, commenting the code that checks for quiescent states based
on interrupting from user-mode execution or the idle loop, removing
some inline attributes, and some code-style changes.
Known/suspected shortcomings:
o I still do not entirely trust the sleep/wakeup logic. Next step
will be to use a private snapshot of the CPU online mask in
rcu_sched_grace_period() -- if the CPU wasn't there at the start
of the grace period, we don't need to hear from it. And the
bit about accounting for changes in online CPUs inside of
rcu_sched_grace_period() is ugly anyway.
o It might be good for rcu_sched_grace_period() to invoke
resched_cpu() when a given CPU wasn't responding quickly,
but resched_cpu() is declared static...
This patch also fixes a long-standing bug in the earlier preemptable-RCU
implementation of synchronize_rcu() that could result in loss of
concurrent external changes to a task's CPU affinity mask. I still cannot
remember who reported this...
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
rcu_batches_completed and rcu_patches_completed_bh are both declared
in rcuclassic.h and rcupreempt.h. This patch removes the extra
prototypes for them from rcupdate.h.
rcu_batches_completed_bh is defined as a static inline in the rcupreempt.h
header file. Trying to export this as EXPORT_SYMBOL_GPL causes linking problems
with the powerpc linker. There's no need to export a static inlined function.
Modules must be compiled with the same type of RCU implementation as the
kernel they are for.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
All uses of list_for_each_rcu() can be profitably replaced by the
easier-to-use list_for_each_entry_rcu(). This patch makes this change
for the Audit system, in preparation for removing the list_for_each_rcu()
API entirely. This time with well-formed SOB.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=10663
Reporter: Daniel Marjamki <danielm77@spray.se>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Limit sysctl_nr_open - we don't want ->max_fds to exceed MAX_INT and
we don't want size calculation for ->fd[] to overflow.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Currently, the mutex debug code checks the lock->owner before lock->magic, so
a corrupt mutex will most likely result in failing the owner check, rather
than the magic check.
This change to debug_mutex_unlock does the magic check first, so
we have a better idea of what breaks.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a common hex array in hexdump.c so everyone can use it.
Add a common hi/lo helper to avoid the shifting masking that is
done to get the upper and lower nibbles of a byte value.
Pull the pack_hex_byte helper from kgdb as it is opencoded many
places in the tree that will be consolidated.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Return type of cpu_rt_runtime_write() should be int instead of ssize_t.
Signed-off-by: Mirco Tischler <mt-ml@gmx.de>
Acked-by: Paul Menage <menage@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It acts exactly like a regular 'cond_resched()', but will not get
optimized away when CONFIG_PREEMPT is set.
Normal kernel code is already preemptable in the presense of
CONFIG_PREEMPT, so cond_resched() is optimized away (see commit
02b67cc3ba "sched: do not do
cond_resched() when CONFIG_PREEMPT").
But when wanting to conditionally reschedule while holding a lock, you
need to use "cond_sched_lock(lock)", and the new function is the BKL
equivalent of that.
Also make fs/locks.c use it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The generic semaphore rewrite had a huge performance regression on AIM7
(and potentially other BKL-heavy benchmarks) because the generic
semaphores had been rewritten to be simple to understand and fair. The
latter, in particular, turns a semaphore-based BKL implementation into a
mess of scheduling.
The attempt to fix the performance regression failed miserably (see the
previous commit 00b41ec261 'Revert
"semaphore: fix"'), and so for now the simple and sane approach is to
instead just go back to the old spinlock-based BKL implementation that
never had any issues like this.
This patch also has the advantage of being reported to fix the
regression completely according to Yanmin Zhang, unlike the semaphore
hack which still left a couple percentage point regression.
As a spinlock, the BKL obviously has the potential to be a latency
issue, but it's not really any different from any other spinlock in that
respect. We do want to get rid of the BKL asap, but that has been the
plan for several years.
These days, the biggest users are in the tty layer (open/release in
particular) and Alan holds out some hope:
"tty release is probably a few months away from getting cured - I'm
afraid it will almost certainly be the very last user of the BKL in
tty to get fixed as it depends on everything else being sanely locked."
so while we're not there yet, we do have a plan of action.
Tested-by: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Alexander Viro <viro@ftp.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit bf726eab37, as it has
been reported to cause a regression with processes stuck in __down(),
apparently because some missing wakeup.
Quoth Sven Wegener:
"I'm currently investigating a regression that has showed up with my
last git pull yesterday. Bisecting the commits showed bf726e
"semaphore: fix" to be the culprit, reverting it fixed the issue.
Symptoms: During heavy filesystem usage (e.g. a kernel compile) I get
several compiler processes in uninterruptible sleep, blocking all i/o
on the filesystem. System is an Intel Core 2 Quad running a 64bit
kernel and userspace. Filesystem is xfs on top of lvm. See below for
the output of sysrq-w."
See
http://lkml.org/lkml/2008/5/10/45
for full report.
In the meantime, we can just fix the BKL performance regression by
reverting back to the good old BKL spinlock implementation instead,
since any sleeping lock will generally perform badly, especially if it
tries to be fair.
Reported-by: Sven Wegener <sven.wegener@stealer.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus found a logic bug: we ignore the version number in a module's
vermagic string if we have CONFIG_MODVERSIONS set, but modversions
also lets through a module with no __versions section for modprobe
--force (with tainting, but still).
We should only ignore the start of the vermagic string if the module
actually *has* crcs to check. Rather than (say) having an
entertaining hissy fit and creating a config option to work around the
buggy code.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We allow missing __versions sections, because modprobe --force strips
it. It makes less sense to allow sections where there's no version
for a specific symbol the module uses, so disallow that.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
Revert "relay: fix splice problem"
docbook: fix bio missing parameter
block: use unitialized_var() in bio_alloc_bioset()
block: avoid duplicate calls to get_part() in disk stat code
cfq-iosched: make io priorities inherit CPU scheduling class as well as nice
block: optimize generic_unplug_device()
block: get rid of likely/unlikely predictions in merge logic
vfs: splice remove_suid() cleanup
cfq-iosched: fix RCU race in the cfq io_context destructor handling
block: adjust tagging function queue bit locking
block: sysfs store function needs to grab queue_lock and use queue_flag_*()
Due to a merge conflict, the sched_relax_domain_level control file was marked
as being handled by cpuset_read/write_u64, but the code to handle it was
actually in cpuset_common_file_read/write.
Since the value being written/read is in fact a signed integer, it should be
treated as such; this patch adds cpuset_read/write_s64 functions, and uses
them to handle the sched_relax_domain_level file.
With this patch, the sched_relax_domain_level can be read and written, and the
correct contents seen/updated.
Signed-off-by: Paul Menage <menage@google.com>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Paul Jackson <pj@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The conversion between virtual and real time is as follows:
dvt = rw/w * dt <=> dt = w/rw * dvt
Since we want the fair sleeper granularity to be in real time, we actually
need to do:
dvt = - rw/w * l
This bug could be related to the regression reported by Yanmin Zhang:
| Comparing with kernel 2.6.25, sysbench+mysql(oltp, readonly) has lots
| of regressions with 2.6.26-rc1:
|
| 1) 8-core stoakley: 28%;
| 2) 16-core tigerton: 20%;
| 3) Itanium Montvale: 50%.
Reported-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yanmin Zhang reported:
| Comparing with kernel 2.6.25, AIM7 (use tmpfs) has more th
| regression under 2.6.26-rc1 on my 8-core stoakley, 16-core tigerton,
| and Itanium Montecito. Bisect located the patch below:
|
| 64ac24e738 is first bad commit
| commit 64ac24e738
| Author: Matthew Wilcox <matthew@wil.cx>
| Date: Fri Mar 7 21:55:58 2008 -0500
|
| Generic semaphore implementation
|
| After I manually reverted the patch against 2.6.26-rc1 while fixing
| lots of conflicts/errors, aim7 regression became less than 2%.
i reproduced the AIM7 workload and can confirm Yanmin's findings that
-.26-rc1 regresses over .25 - by over 67% here.
Looking at the workload i found and fixed what i believe to be the real
bug causing the AIM7 regression: it was inefficient wakeup / scheduling
/ locking behavior of the new generic semaphore code, causing suboptimal
performance.
The problem comes from the following code. The new semaphore code does
this on down():
spin_lock_irqsave(&sem->lock, flags);
if (likely(sem->count > 0))
sem->count--;
else
__down(sem);
spin_unlock_irqrestore(&sem->lock, flags);
and this on up():
spin_lock_irqsave(&sem->lock, flags);
if (likely(list_empty(&sem->wait_list)))
sem->count++;
else
__up(sem);
spin_unlock_irqrestore(&sem->lock, flags);
where __up() does:
list_del(&waiter->list);
waiter->up = 1;
wake_up_process(waiter->task);
and where __down() does this in essence:
list_add_tail(&waiter.list, &sem->wait_list);
waiter.task = task;
waiter.up = 0;
for (;;) {
[...]
spin_unlock_irq(&sem->lock);
timeout = schedule_timeout(timeout);
spin_lock_irq(&sem->lock);
if (waiter.up)
return 0;
}
the fastpath looks good and obvious, but note the following property of
the contended path: if there's a task on the ->wait_list, the up() of
the current owner will "pass over" ownership to that waiting task, in a
wake-one manner, via the waiter->up flag and by removing the waiter from
the wait list.
That is all and fine in principle, but as implemented in
kernel/semaphore.c it also creates a nasty, hidden source of contention!
The contention comes from the following property of the new semaphore
code: the new owner owns the semaphore exclusively, even if it is not
running yet.
So if the old owner, even if just a few instructions later, does a
down() [lock_kernel()] again, it will be blocked and will have to wait
on the new owner to eventually be scheduled (possibly on another CPU)!
Or if another task gets to lock_kernel() sooner than the "new owner"
scheduled, it will be blocked unnecessarily and for a very long time
when there are 2000 tasks running.
I.e. the implementation of the new semaphores code does wake-one and
lock ownership in a very restrictive way - it does not allow
opportunistic re-locking of the lock at all and keeps the scheduler from
picking task order intelligently.
This kind of scheduling, with 2000 AIM7 processes running, creates awful
cross-scheduling between those 2000 tasks, causes reduced parallelism, a
throttled runqueue length and a lot of idle time. With increasing number
of CPUs it causes an exponentially worse behavior in AIM7, as the chance
for a newly woken new-owner task to actually run anytime soon is less
and less likely.
Note that it takes just a tiny bit of contention for the 'new-semaphore
catastrophy' to happen: the wakeup latencies get added to whatever small
contention there is, and quickly snowball out of control!
I believe Yanmin's findings and numbers support this analysis too.
The best fix for this problem is to use the same scheduling logic that
the kernel/mutex.c code uses: keep the wake-one behavior (that is OK and
wanted because we do not want to over-schedule), but also allow
opportunistic locking of the lock even if a wakee is already "in
flight".
The patch below implements this new logic. With this patch applied the
AIM7 regression is largely fixed on my quad testbox:
# v2.6.25 vanilla:
..................
Tasks Jobs/Min JTI Real CPU Jobs/sec/task
2000 56096.4 91 207.5 789.7 0.4675
2000 55894.4 94 208.2 792.7 0.4658
# v2.6.26-rc1-166-gc0a1811 vanilla:
...................................
Tasks Jobs/Min JTI Real CPU Jobs/sec/task
2000 33230.6 83 350.3 784.5 0.2769
2000 31778.1 86 366.3 783.6 0.2648
# v2.6.26-rc1-166-gc0a1811 + semaphore-speedup:
...............................................
Tasks Jobs/Min JTI Real CPU Jobs/sec/task
2000 55707.1 92 209.0 795.6 0.4642
2000 55704.4 96 209.0 796.0 0.4642
i.e. a 67% speedup. We are now back to within 1% of the v2.6.25
performance levels and have zero idle time during the test, as expected.
Btw., interactivity also improved dramatically with the fix - for
example console-switching became almost instantaneous during this
workload (which after all is running 2000 tasks at once!), without the
patch it was stuck for a minute at times.
There's another nice side-effect of this speedup patch, the new generic
semaphore code got even smaller:
text data bss dec hex filename
1241 0 0 1241 4d9 semaphore.o.before
1207 0 0 1207 4b7 semaphore.o.after
(because the waiter.up complication got removed.)
Longer-term we should look into using the mutex code for the generic
semaphore code as well - but i's not easy due to legacies and it's
outside of the scope of v2.6.26 and outside the scope of this patch as
well.
Bisected-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
this replaces the rq->clock stuff (and possibly cpu_clock()).
- architectures that have an 'imperfect' hardware clock can set
CONFIG_HAVE_UNSTABLE_SCHED_CLOCK
- the 'jiffie' window might be superfulous when we update tick_gtod
before the __update_sched_clock() call in sched_clock_tick()
- cpu_clock() might be implemented as:
sched_clock_cpu(smp_processor_id())
if the accuracy proves good enough - how far can TSC drift in a
single jiffie when considering the filtering and idle hooks?
[ mingo@elte.hu: various fixes and cleanups ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
David Miller pointed it out that nothing in cpu_clock() sets
prev_cpu_time. This caused __sync_cpu_clock() to be called
all the time - against the intention of this code.
The result was that in practice we hit a global spinlock every
time cpu_clock() is called - which - even though cpu_clock()
is used for tracing and debugging, is suboptimal.
While at it, also:
- move the irq disabling to the outest layer,
this should make cpu_clock() warp-free when called with irqs
enabled.
- use long long instead of cycles_t - for platforms where cycles_t
is 32-bit.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When I echoed 0 into the "cpu.shares" file, a Div0 error occured.
We found it is caused by the following calling.
sched_group_set_shares(tg, shares)
set_se_shares(tg->se[i], shares/nr_cpu_ids)
__set_se_shares(se, shares)
div64_64((1ULL<<32), shares)
When the echoed value was less than the number of processores, the result of the
sentence "shares/nr_cpu_ids" was 0, and then the system called div64() to divide
the result, the Div0 error occured.
It is unnecessary that the shares value is divided by nr_cpu_ids, I think.
Because in the function __update_group_shares_cpu() and init_tg_cfs_entry(),
the shares value isn't divided by nr_cpu_ids when setting shares of the sched
entity.
This patch fixes this bug. And echoing ULONG_MAX value into cpu.shares also
causes Div0 error, so we set a macro MAX_SHARES to limit the max value of
shares.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Concurrent calls to detach_destroy_domains and arch_init_sched_domains
were prevented by the old scheduler subsystem cpu hotplug mutex. When
this got converted to get_online_cpus() the locking got broken.
Unlike before now several processes can concurrently enter the critical
sections that were protected by the old lock.
So use the already present doms_cur_mutex to protect these sections again.
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Revert debugging commit 7ba2e74ab5.
print_cfs_rq_tasks() can induce live-lock if a task is dequeued
during list traversal.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
http://bugzilla.kernel.org/show_bug.cgi?id=10545
sched_stats.h says that __sched_info_switch is "called when prev !=
next" in the comment. sched.c should therefore do that.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Gautham R Shenoy reported:
> While running the usual CPU-Hotplug stress tests on linux-2.6.25,
> I noticed the following in the console logs.
>
> This is a wee bit difficult to reproduce. In the past 10 runs I hit this
> only once.
>
> ------------[ cut here ]------------
>
> WARNING: at kernel/sched.c:962 hrtick+0x2e/0x65()
>
> Just wondering if we are doing a good job at handling the cancellation
> of any per-cpu scheduler timers during CPU-Hotplug.
This looks like its indeed not cancelled at all and migrates the it to
another cpu. Fix it via a proper hotplug notifier mechanism.
Reported-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: stable@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We currently use an optimization to skip the overhead of wake-idle
processing if more than one task is assigned to a run-queue. The
assumption is that the system must already be load-balanced or we
wouldnt be overloaded to begin with.
The problem is that we are looking at rq->nr_running, which may include
RT tasks in addition to CFS tasks. Since the presence of RT tasks
really has no bearing on the balance status of CFS tasks, this throws
the calculation off.
This patch changes the logic to only consider the number of CFS tasks
when making the decision to optimze the wake-idle.
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
CC: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Dmitry Adamushko pointed out a logic error in task_wake_up_rt() where we
will always evaluate to "true". You can find the thread here:
http://lkml.org/lkml/2008/4/22/296
In reality, we only want to try to push tasks away when a wake up request is
not going to preempt the current task. So lets fix it.
Note: We introduce test_tsk_need_resched() instead of open-coding the flag
check so that the merge-conflict with -rt should help remind us that we
may need to support NEEDS_RESCHED_DELAYED in the future, too.
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
CC: Dmitry Adamushko <dmitry.adamushko@gmail.com>
CC: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Noticed by sparse:
kernel/sched.c:760:20: warning: symbol 'sched_feat_names' was not declared. Should it be static?
kernel/sched.c:767:5: warning: symbol 'sched_feat_open' was not declared. Should it be static?
kernel/sched_fair.c:845:3: warning: returning void-valued expression
kernel/sched.c:4386:3: warning: returning void-valued expression
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The C files are included directly in sched.c, so they are
effectively static.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Joel noticed that the !lw->inv_weight contition isn't unlikely anymore so
remove the unlikely annotation. Also, remove the two div64_u64() inv_weight
calculations, which makes them rely on the calc_delta_mine() path as well.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Normalized sleeper uses calc_delta*() which requires that the rq load is
already updated, so move account_entity_enqueue() before place_entity()
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdb: kconfig fix xconfig/menuconfig element
kgdb: fix signedness mixmatches, add statics, add declaration to header
kgdb: 1000 loops for the single step test in kgdbts
kgdb: trivial sparse fixes in kgdb test-suite
kgdb: minor documentation fixes
Since FUTEX_FD was scheduled for removal in June 2007 lets remove it.
Google Code search found no users for it and NGPT was abandoned in 2003
according to IBM. futex.h is left untouched to make sure the id does
not get reassigned. Since queue_me() has no users left it is commented
out to avoid a warning, i didnt remove it completely since it is part of
the internal api (matching unqueue_me())
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (removed rest)
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Noticed by sparse:
arch/x86/kernel/kgdb.c:556:15: warning: symbol 'kgdb_arch_pc' was not declared. Should it be static?
kernel/kgdb.c:149:8: warning: symbol 'kgdb_do_roundup' was not declared. Should it be static?
kernel/kgdb.c:193:22: warning: symbol 'kgdb_arch_pc' was not declared. Should it be static?
kernel/kgdb.c:712:5: warning: symbol 'remove_all_break' was not declared. Should it be static?
Related to kgdb_hex2long:
arch/x86/kernel/kgdb.c:371:28: warning: incorrect type in argument 2 (different signedness)
arch/x86/kernel/kgdb.c:371:28: expected long *long_val
arch/x86/kernel/kgdb.c:371:28: got unsigned long *<noident>
kernel/kgdb.c:469:27: warning: incorrect type in argument 2 (different signedness)
kernel/kgdb.c:469:27: expected long *long_val
kernel/kgdb.c:469:27: got unsigned long *<noident>
kernel/kgdb.c:470:27: warning: incorrect type in argument 2 (different signedness)
kernel/kgdb.c:470:27: expected long *long_val
kernel/kgdb.c:470:27: got unsigned long *<noident>
kernel/kgdb.c:894:27: warning: incorrect type in argument 2 (different signedness)
kernel/kgdb.c:894:27: expected long *long_val
kernel/kgdb.c:894:27: got unsigned long *<noident>
kernel/kgdb.c:895:27: warning: incorrect type in argument 2 (different signedness)
kernel/kgdb.c:895:27: expected long *long_val
kernel/kgdb.c:895:27: got unsigned long *<noident>
kernel/kgdb.c:1127:28: warning: incorrect type in argument 2 (different signedness)
kernel/kgdb.c:1127:28: expected long *long_val
kernel/kgdb.c:1127:28: got unsigned long *<noident>
kernel/kgdb.c:1132:25: warning: incorrect type in argument 2 (different signedness)
kernel/kgdb.c:1132:25: expected long *long_val
kernel/kgdb.c:1132:25: got unsigned long *<noident>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
The kernel module loader used to be much too happy to allow loading of
modules for the wrong kernel version by default. For example, if you
had MODVERSIONS enabled, but tried to load a module with no version
info, it would happily load it and taint the kernel - whether it was
likely to actually work or not!
Generally, such forced module loading should be considered a really
really bad idea, so make it conditional on a new config option
(MODULE_FORCE_LOAD), and make it default to off.
If somebody really wants to force module loads, that's their problem,
but we should not encourage it. Especially as it happened to me by
mistake (ie regular unversioned Fedora modules getting loaded) causing
lots of strange behavior.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no harm, when users can read the info and we ask often enough
during debugging for this kind of information.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
File permissions for
/sys/devices/system/clocksource/clocksource0/available_clocksource
are 600 which allows write access. But this is in fact a read only
file. So change permissions to 400.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The helper function hrtimer_callback_running() is used in
kernel/hrtimer.c as well as in the updated net/can/bcm.c which now
supports hrtimers. Moving the helper function to hrtimer.h removes the
duplicate definition in the C-files.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Force constants in kernel/timeconst.h (except shift counts) to be 64 bits,
using U64_C() constructor macros, and eliminate constants that cannot
be represented at all in 64 bits. This avoids warnings with some gcc
versions.
Drop generating 64-bit constants, since we have no real hope of
getting a full set (operation on 64-bit values requires a 128-bit
intermediate result, which gcc only supports on 64-bit platforms, and
only with libgcc support on some.) Note that the use of these
constants does not depend on if we are on a 32- or 64-bit architecture.
This resolves Bugzilla 10153.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Uwe Kleine-Koenig has some strange hardware where one of the shared
interrupts can be asserted during boot before the appropriate driver
loads. Requesting the shared irq line from another driver result in a
spurious interrupt storm which finally disables the interrupt line.
I have seen similar behaviour on resume before (the hardware does not
work anymore so I can not verify).
Change the spurious disable logic to increment the disable depth and
mark the interrupt with an extra flag which allows us to reenable the
interrupt when a new driver arrives which requests the same irq
line. In the worst case this will disable the irq again via the
spurious trap, but there is a decent chance that the new driver is the
one which can handle the already asserted interrupt and makes the box
usable again.
Eric Biederman said further: This case also happens on a regular basis
in kdump kernels where we deliberately don't shutdown the hardware
before starting the new kernel. This patch should reduce the need for
using irqpoll in that situation by a small amount.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-and-Acked-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
With s390 the last arch switched to the generic sys_ptrace yesterday so
we can now kill the ifdef around it to enforce every new port it using
it instead of introducing new weirdo versions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
timer_stats_timer_set_start_info is invoked twice, additionally, the
invocation of this function can be moved to where it is only called when a
delay is really required.
Signed-off-by: Andrew Liu <shengping.liu@windriver.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The extended crashkernel syntax is a little confusing in the way it handles
ranges. eg:
crashkernel=512M-2G:64M,2G-:128M
Means if the machine has between 512M and 2G of memory the crash region should
be 64M, and if the machine has 2G of memory the region should be 64M. Only if
the machine has more than 2G memory will 128M be allocated.
Although that semantic is correct, it is somewhat baffling. Instead I propose
that the end of the range means the first address past the end of the range,
ie: 512M up to but not including 2G.
[bwalle@suse.de: clarify inclusive/exclusive in crashkernel commandline in documentation]
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Bernhard Walle <bwalle@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the leap second handling from second_overflow(), which doesn't have to
check for it every second anymore. With CONFIG_NO_HZ this also makes sure the
leap second is handled close to the full second. Additionally this makes it
possible to abort a leap second properly by resetting the STA_INS/STA_DEL
status bits.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
current_tick_length used to do a little more, but now it just returns
tick_length, which we can also access directly at the few places, where it's
needed.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As TICK_LENGTH_SHIFT is used for more than just the tick length, the name
isn't quite approriate anymore, so this renames it to NTP_SCALE_SHIFT.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for setting the TAI value (International Atomic Time). The
value is reported back to userspace via timex (as we don't have a
ntp_gettime() syscall).
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
time_offset is already a 64bit value but its resolution barely used, so this
makes better use of it by replacing SHIFT_UPDATE with TICK_LENGTH_SHIFT.
Side note: the SHIFT_HZ in SHIFT_UPDATE was incorrect for CONFIG_NO_HZ and the
primary reason for changing time_offset to 64bit to avoid the overflow.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes time_freq to a 64bit value and makes it static (the only outside
user had no real need to modify it). Intermediate values were already 64bit,
so the change isn't that big, but it saves a little in shifts by replacing
SHIFT_NSEC with TICK_LENGTH_SHIFT. PPM_SCALE is then used to convert between
user space and kernel space representation.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a few more things from the ntp nanokernel related to user space.
It's now possible to select the resolution used of some values via STA_NANO
and the kernel reports in which mode it works (pll/fll).
If some values for adjtimex() are outside the acceptable range, they are now
simply normalized instead of letting the syscall fail. I removed
MOD_CLKA/MOD_CLKB as the mapping didn't really makes any sense, the kernel
doesn't support setting the clock.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is mostly a style cleanup of ntp.c and extracts part of do_adjtimex as
ntp_update_offset(). Otherwise the functionality is still the same as before.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86 is the only arch right now, which provides an optimized for
div_long_long_rem and it has the downside that one has to be very careful that
the divide doesn't overflow.
The API is a little akward, as the arguments for the unsigned divide are
signed. The signed version also doesn't handle a negative divisor and
produces worse code on 64bit archs.
There is little incentive to keep this API alive, so this converts the few
users to the new API.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename div64_64 to div64_u64 to make it consistent with the other divide
functions, so it clearly includes the type of the divide. Move its definition
to math64.h as currently no architecture overrides the generic implementation.
They can still override it of course, but the duplicated declarations are
avoided.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Avi Kivity <avi@qumranet.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This converts a few users of do_div to div_[su]64 and this demonstrates nicely
how it can reduce some expressions to one-liners.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
currently cpu hotplug (unplug) seems broken on s390 and likely others. On cpu
unplug the system starts to behave very strange and hangs.
I bisected the problem to the following commit:
commit 48f20a9a94
Author: Olof Johansson <olof@lixom.net>
Date: Tue Mar 4 15:23:25 2008 -0800
tasklets: execute tasklets in the same order they were queued
Reverting this patch seems to fix the problem. I looked into takeover_tasklet
and it seems that there is a way to corrupt the tail pointer of the current
cpu. If the tasklet list of the frozen cpu is empty, the tail pointer of the
current cpu points to the address of the head pointer of the stopped cpu and
not to the next pointer of a tasklet_struct.
This patch avoids the list splice of the list is empty and cpu hotplug seems
to work as the tail pointer is not corrupted. Olof, can you look into that
patch and ACK/NACK it so Andrew can push this to Linus, if appropriate?
Please note that some lines are longer than 80 chars, but line-wrapping looked
worse that this version.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide module unload callback. Required by the gcov profiling
infrastructure to keep track of profiling data structures.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Make verify_export_symbols check the modules unused, unused_gpl and
gpl_future syms.
Inspired by Jan Beulich's fix, but table-driven.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Obvious typo, but I don't know of any modules with unused GPL exports,
and then it would take someone noticing that the version shouldn't
have matched in a dependent module.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
__find_symbol() has grown over time: there are now 5 different arrays
of symbols it traverses. It also shouldn't print out a warning on
some calls (ie. verify_symbol which simply checks for name clashes,
and __symbol_put which checks for bugs).
1) Rename to find_symbol: no need for underscores.
2) Use bool and add "warn" parameter to suppress warnings.
3) Make table-driven rather than open coded.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (179 commits)
ACPI: Fix acpi_processor_idle and idle= boot parameters interaction
acpi: fix section mismatch warning in pnpacpi
intel_menlo: fix build warning
ACPI: Cleanup: Remove unneeded, multiple local dummy variables
ACPI: video - fix permissions on some proc entries
ACPI: video - properly handle errors when registering proc elements
ACPI: video - do not store invalid entries in attached_array list
ACPI: re-name acpi_pm_ops to acpi_suspend_ops
ACER_WMI/ASUS_LAPTOP: fix build bug
thinkpad_acpi: fix possible NULL pointer dereference if kstrdup failed
ACPI: check a return value correctly in acpi_power_get_context()
#if 0 acpi/bay.c:eject_removable_drive()
eeepc-laptop: add hwmon fan control
eeepc-laptop: add backlight
eeepc-laptop: add base driver
ACPI: thinkpad-acpi: bump up version to 0.20
ACPI: thinkpad-acpi: fix selects in Kconfig
ACPI: thinkpad-acpi: use a private workqueue
ACPI: thinkpad-acpi: fluff really minor fix
ACPI: thinkpad-acpi: use uppercase for "LED" on user documentation
...
Fixed conflicts in drivers/acpi/video.c and drivers/misc/intel_menlow.c
manually.
hrtimers have now dynamic users in the network code. Put them under
debugobjects surveillance as well.
Add calls to the generic object debugging infrastructure and provide fixup
functions which allow to keep the system alive when recoverable problems have
been detected by the object debugging core code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add calls to the generic object debugging infrastructure and provide fixup
functions which allow to keep the system alive when recoverable problems have
been detected by the object debugging core code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Greg KH <greg@kroah.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use kmem_cache_zalloc(), remove large amounts of initialisation code and
ifdeffery.
Note: this assumes that memset(*atomic_t, 0) correctly initialises the
atomic_t. This is true for all present archtiectures and if it becomes false
for a future architecture then we'll need to make large changes all over the
place anyway.
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix update_console_cmdline() not to to read beyond the terminating zero of its
name argument.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a minimalistic braille screen reader support. This is meant to
be used by blind people e.g. on boot failures or when / cannot be mounted
etc and thus the userland screen readers can not work.
[akpm@linux-foundation.org: fix exports]
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Jiri Kosina <jikos@jikos.cz>
Cc: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new BDI capability flag: BDI_CAP_NO_ACCT_WB. If this flag is
set, then don't update the per-bdi writeback stats from
test_set_page_writeback() and test_clear_page_writeback().
Misc cleanups:
- convert bdi_cap_writeback_dirty() and friends to static inline functions
- create a flag that includes all three dirty/writeback related flags,
since almst all users will want to have them toghether
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These values represent the nesting level of a namespace and pids living in it,
and it's always non-negative.
Turning this from int to unsigned int saves some space in pid.c (11 bytes on
x86 and 64 on ia64) by letting the compiler optimize the pid_nr_ns a bit.
E.g. on ia64 this removes the sign extension calls, which compiler adds to
optimize access to pid->nubers[ns->level].
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the needlessly global marker_debug being static gcc can optimize the
unused code away.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. sys_getpgid() needs rcu_read_lock() to derive the pgrp _nr, even if
the task is current, otherwise we can race with another thread which
does sys_setpgid().
2. Use rcu_read_lock() instead of tasklist_lock when pid != 0, make sure
that we don't use the NULL pid if the task exits right after successful
find_task_by_vpid().
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. sys_getsid() needs rcu_read_lock() to derive the session _nr, even if
the task is current, otherwise we can race with another thread which
does sys_setsid().
2. The task can exit between find_task_by_vpid() and task_session_vnr(),
in that unlikely case sys_getsid() returns 0 instead of -ESRCH.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use change_pid() instead of detach_pid() + attach_pid() in
__set_special_pids().
This way task_session() is not NULL in between.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use change_pid() instead of detach_pid() + attach_pid() in sys_setpgid().
This way task_pgrp() is not NULL in between.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on Eric W. Biederman's idea.
Without tasklist_lock held task_session()/task_pgrp() can return NULL if the
caller races with setprgp()/setsid() which does detach_pid() + attach_pid().
This can happen even if task == current.
Intoduce the new helper, change_pid(), which should be used instead. This way
the caller always sees the special pid != NULL, either old or new.
Also change the prototype of attach_pid(), it always returns 0 and nobody
check the returned value.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on Eric W. Biederman's idea.
Unless task == current, without tasklist_lock held task_session()/task_pgrp()
can return NULL if the caller races with de_thread() which switches the group
leader.
Change transfer_pid() to not clear old->pids[type].pid for the old leader.
This means that its .pid can point to "nowhere", but this is already true for
sub-threads, and the old leader is not group_leader() any longer. IOW, with
or without this change we can't trust task's special pids unless it is the
group leader.
With this change the following code
rcu_read_lock();
task = find_task_by_xxx();
do_something(task_pgrp(task), task_session(task));
rcu_read_unlock();
can't race with exec and hit the NULL pid.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are some places that are known to operate on tasks'
global pids only:
* the rest_init() call (called on boot)
* the kgdb's getthread
* the create_kthread() (since the kthread is run in init ns)
So use the find_task_by_pid_ns(..., &init_pid_ns) there
and schedule the find_task_by_pid for removal.
[sukadev@us.ibm.com: Fix warning in kernel/pid.c]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pid to lookup a task by is passed inside taskstats code via genetlink
message.
Since netlink packets are now processed in the context of the sending task,
this is correct to lookup the task with find_task_by_vpid() here.
Besides, I fix the call to fill_pid() from taskstats_exit(), since the
tsk->pid is not required in fill_pid() in this case, and the pid field on
task_struct is going to be deprecated as well.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Cc: Jonathan Lim <jlim@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The callers of free_pidmap() pass 2 members of "struct upid", we can just
pass "struct upid *" instead. Shaves off 10 bytes from pid.o.
Also, simplify the alloc_pid's "out_free:" error path a little bit. This
way it looks more clear which subset of pid->numbers[] we are freeing.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc :Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Operations are now a shared const function block as with most other Linux
objects
- Introduce wrappers for some optional functions to get consistent behaviour
- Wrap put_char which used to be patched by the tty layer
- Document which functions are needed/optional
- Make put_char report success/fail
- Cache the driver->ops pointer in the tty as tty->ops
- Remove various surplus lock calls we no longer need
- Remove proc_write method as noted by Alexey Dobriyan
- Introduce some missing sanity checks where certain driver/ldisc
combinations would oops as they didn't check needed methods were present
[akpm@linux-foundation.org: fix fs/compat_ioctl.c build]
[akpm@linux-foundation.org: fix isicom]
[akpm@linux-foundation.org: fix arch/ia64/hp/sim/simserial.c build]
[akpm@linux-foundation.org: fix kgdb]
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Afaics, currently there are no kernel problems with ptracing init, it can't
lose SIGNAL_UNKILLABLE flag and be killed/stopped by accident.
The ability to strace/debug init can be very useful if you try to figure out
why it does not work as expected.
However, admin should know what he does, "gdb /sbin/init 1" stops init, it
can't reap orphaned zombies or take care of /etc/inittab until continued. It
is even possible to crash init (and thus the whole system) if you wish,
ptracer has full control.
See also the long discussion: http://marc.info/?t=120628018600001
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nobody can block/ignore SIGSTOP, no need to use force_sig_specific() in
ptrace_attach. Use the "regular" send_sig_info().
With this patch stracing of /sbin/init doesn't clear its SIGNAL_UNKILLABLE,
but not that this makes ptracing of init safe.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently __ptrace_unlink() checks list_empty(->ptrace_list) to figure out
whether the child was reparented. Change the code to use ptrace_reparented()
to make this check more explicit and consistent.
No functional changes.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add another trivial helper for the sake of grep. It also auto-documents the
fact that ->parent != real_parent implies ->ptrace.
No functional changes.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a couple of small comments, it is not easy to see what this code does.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
exit.c has numerous "->exit_signal == -1" comparisons, this check is subtle
and deserves a helper. Imho makes the code more parseable for humans. At
least it's surely more greppable.
Also, a couple of whitespace cleanups. No functional changes.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds the set_restore_sigmask() inline in <linux/thread_info.h> and
replaces every set_thread_flag(TIF_RESTORE_SIGMASK) with a call to it. No
change, but abstracts the details of the flag protocol from all the calls.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the buggy /sbin/init hangs if SIGSEGV/etc happens. The kernel sends
the signal, init dequeues it and ignores, returns from the exception, repeats
the faulting instruction, and so on forever.
Imho, such a behaviour is not good. I think that the explicit loud death of
the buggy /sbin/init is better than the silent hang.
Change force_sig_info() to clear SIGNAL_UNKILLABLE when the task should be
really killed.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The global init has a lot of long standing problems with the unhandled fatal
signals.
- The "is_global_init(current)" check in get_signal_to_deliver()
protects only the main thread. Sub-thread can dequee the fatal
signal and shutdown the whole thread group except the main thread.
If it dequeues SIGSTOP /sbin/init will be stopped, this is not
right too. Note that we can't use is_global_init(->group_leader),
this breaks exec and this can't solve other problems we have.
- Even if afterwards ignored, the fatal signals sets SIGNAL_GROUP_EXIT
on delivery. This breaks exec, has other bad implications, and this
is just wrong.
Introduce the new SIGNAL_UNKILLABLE flag to fix these problems. It also helps
to solve some other problems addressed by the subsequent patches.
Currently we use this flag for the global init only, but it could also be used
by kthreads and (perhaps) by the sub-namespace inits.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that task_session() can't return a false NULL, check_kill_permission()
doesn't need tasklist_lock.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This wasn't documented, but as Atsushi Tsuji pointed out
check_kill_permission() needs tasklist_lock for task_session_nr(). I missed
this fact when removed tasklist from the callers.
Change check_kill_permission() to take tasklist_lock for the SIGCONT case.
Re-order security checks so that we take tasklist_lock only if/when it is
actually needed. This is a minimal fix for now, tasklist will be removed
later.
Also change the code to use task_session() instead of task_session_nr().
Also, remove the SIGCONT check from cap_task_kill(), it is bogus (and the
whole function is bogus. Serge, Eric, why it is still alive?).
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Atsushi Tsuji <a-tsuji@bk.jp.nec.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
