Using SIT tunnels with VRFs works fine if the underlay device is in a
VRF and the link parameter is set to the VRF device. e.g.,
ip tunnel add jtun mode sit remote <addr> local <addr> dev myvrf
Update the device check to allow the link to be the enslaved device as
well. e.g.,
ip tunnel add jtun mode sit remote <addr> local <addr> dev eth4
where eth4 is enslaved to myvrf.
Reported-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checkpatch.pl error:
ERROR: space prohibited before open square bracket '['.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an entry for IFLA_BRPORT_NEIGH_SUPPRESS to bridge port policies.
Fixes: 821f1b21ca ("bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd flood")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart says:
====================
net: mvpp2: various improvements
This series includes various patches improving the Marvell PPv2 driver.
I send them as a series to avoid any possible merge conflict.
- Patches 1 and 2 improve the initializing of the Tx and Rx FIFO.
- Patch 3 initialize the RSS table to evenly distribute the ingress
packets across multiple Rx queues based on their hashes.
- Patch 4 limits the number of TSO segments sent to the driver, to avoid
having more segments to handle than the corresponding number of
available descriptors.
- Patch 5 and 6 are cosmetic improvements.
This applies on today's net-next branch, The patches were tested
extensively (I ran iperf and http downloads in parallel, transferring
TBs of data).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Two functions were always used to set the DMA addresses in Tx
descriptors, because this address is split into a base+offset in the
descriptors. A mask was used to come up with the base and offset
addresses and two functions were called, mvpp2_txdesc_dma_addr_set() and
mvpp2_txdesc_offset_set().
This patch moves the base+offset calculation logic to
mvpp2_txdesc_dma_addr_set(), and removes mvpp2_txdesc_offset_set() to
simplify things.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch using the MVPP2_AGGR_TXQ_SIZE everywhere instead of the
size field of aggr_txq, as the size never change and is always equal to
the MVPP2_AGGR_TXQ_SIZE define.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Too many TSO descriptors can be required for the default queue size,
when using small MSS values for example. Prevent this by adding a
maximum number of allowed TSO segments (300). In addition set a stop and
a wake thresholds to stop the queue when there's no room for a 1 "worst
case scenario skb". Wake up the queue when the number of descriptors is
low enough.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch initialize the RSS tables to evenly (depending on the packets
RSS hashes) distribute the packets across port Rx queues. This helps to
handle packets on different CPUs to improve performances, as more queues
will be used in parallel.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far only the Rx FIFO size was initialized. For PPv2.2 the Tx FIFO
size can be set as well. This patch initializes the Tx FIFO size for
PPv2.2 controllers to 3K.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx FIFO size was set to the same value for all ports. This patch
sets it depending on the maximum speed a given port can handle. This is
only working for PPv2.2.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-10-30
1) Change some variables that can't be negative
from int to unsigned int. From Alexey Dobriyan.
2) Remove a redundant header initialization in esp6.
From Colin Ian King.
3) Some BUG to BUG_ON conversions.
From Gustavo A. R. Silva.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable len is being assigned a value that is never read,
hence the assignment is redundant and can be removed. Cleans
up clang warning:
drivers/net/hamradio/mkiss.c:443:3: warning: Value stored to
'len' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sockmap test is using two programs that use bpf_trace_printk()
which prints into trace_pipe, but nothing is reading it.
Remove it.
Fixes: 6f6d33f3b3 ("bpf: selftests add sockmap tests")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the swap macro and remove unnecessary variable tmp.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the swap macro and remove unnecessary variable tmp.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the swap macro and remove unnecessary variable tmp.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions pci_alloc_consistent is obsolete. So it is replaced
with dma_alloc_coherent
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike ipip and gre, ip_vti never uses err_count in vti4_err,
so no need to check err_count in vti_xmit, it's value always 0.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: Allow non-fatal messages to be passed in extack
There are many cases where networking subsystems throw non-fatal warning
messages that end up in dmesg / kernel log to which a user making the
change is completely oblivious. This set makes the extack facility
usable for returning such messages.
The case in point here is spectrum and adding FIB rules which causes an
offload abort. Make the use case more user friendly by letting the user
know that offload is no longer happening because of the rule change.
v2
- kept the offload abort in a work queue entry per Ido's comment
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a FIB rule on a spectrum platform silently aborts FIB offload:
$ ip ru add pref 99 from all to 192.168.1.1 table 10
$ dmesg -c
[ 623.144736] mlxsw_spectrum 0000:03:00.0: FIB abort triggered. Note that FIB entries are no longer being offloaded to this device.
This patch reworks FIB rule handling to return a message to the user:
$ ip ru add pref 99 from all to 8.8.8.8 table 11
Error: spectrum: FIB rules not supported. Aborting offload.
spectrum currently only checks whether the fib rule is a default rule or
an l3mdev rule, both of which it knows how to handle. Any other it aborts
FIB offload. Move the processing to check the rule type inline with the
user request. If the rule is an unsupported one, then a work queue entry
is used to abort the offload. Change the rule delete handling to just
return since it does nothing at the moment.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack to fib_notifier_info and plumb through stack to
call_fib_rule_notifiers, call_fib_entry_notifiers and
call_fib6_entry_notifiers. This allows notifer handlers to
return messages to user.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NLMSGERR API already carries data (eg, a cookie) on the success path.
Allow a message string to be returned as well.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: add port parsing functions
This patchset adds port parsing functions called early in the new
bindings parsing stage, which regroup all the fetching of static data
available at the port level, including the port's type, name and CPU
master interface.
This simplifies the rest of the code which does not need to dig into
device tree or platform data again in order to check a port's type or
name.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that slave dsa_port always have their name set, there is no need to
pass it to dsa_slave_create() anymore. Remove this argument.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the optional "label" property and assign a default one directly at
parse time instead of doing it when creating the slave.
For legacy, simply assign the port name stored in cd->port_names.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fetching the master device can be done directly when a port is parsed
from device tree or pdata, instead of waiting until dsa_dst_parse.
Now that -EPROBE_DEFER is returned before we add the switch to the tree,
there is no need to check for this error after dsa_dst_parse.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign a port's type at parsed time instead of waiting for the tree to
be completed.
Because this is now done earlier, we can use the port's type in
dsa_port_is_* helpers instead of digging again in topology description.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add symmetrical DSA port parsing functions for pdata and device tree,
used to parse and validate a given port node or platform data.
They don't do much for the moment but will be extended later on to
assign a port type and get device references.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point into hiding the -EINVAL error code in ERR_PTR from a
dsa_get_ports function, simply get the "ports" node directly from within
the dsa_parse_ports_dn function.
This also has the effect to make the pdata and device tree handling code
symmetrical inside _dsa_register_switch.
At the same time, rename dsa_parse_ports_dn to dsa_parse_ports_of
because _of is a more common suffix for device tree parsing functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the verifier got progressively smarter over time and size of its internal
state grew as well. Time to reduce the memory consumption.
Before:
sizeof(struct bpf_verifier_state) = 6520
After:
sizeof(struct bpf_verifier_state) = 896
It's done by observing that majority of BPF programs use little to
no stack whereas verifier kept all of 512 stack slots ready always.
Instead dynamically reallocate struct verifier state when stack
access is detected.
Runtime difference before vs after is within a noise.
The number of processed instructions stays the same.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vijaya Mohan Guvva says:
====================
liquidio: switchdev support for LiquidIO NIC
patch1 of this patch set adds switchdev support for SRIOV capable
LiquidIO NIC, so that for every SRIOV VF on LiquidIO, a representor
netdev is created on hypervisor. It also has changes to send representor
interface configurations like admin state and MTU to LiquidIO firmware and
to retrieve HW counted VF stats for VF representor.
patch2 adds support for switchdev enable/disable from devlink
Patchset Change Log:
V2 -> V3:
* Use mac address as the physical switchID.
* Check for eswitch_mode before returning switchID
V1 -> V2:
* Name the representors "pfXvfY".
* Drop patch3 (ethtool support for switchdev ports) that was in V1
because it's not necessary.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable and disable switchdev on SRIOV capable LiquidIO NIC with devlink.
Create representor netdev for each SRIOV VF function on SRIOV enable and
and do the cleanup on SRIOV disable.
Signed-off-by: Vijaya Mohan Guvva <vijaya.guvva@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable switchdev for SRIOV capable LiquidIO NIC. It registers
a representor netdev (with switchdev_ops) for each SRIOV VF created.
It also has changes to send representor interface configurations like
admin state and MTU to LiquidIO firmware and to retrieve HW counted
VF stats for VF representor.
Signed-off-by: Vijaya Mohan Guvva <vijaya.guvva@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2017-10-31 mlx5e stats groups
This series from Kamal introduces an important refactoring for mlx5e stats
handling, which groups the stats into generic groups structure which allows
to control the behavior and stats reporting per group in a modular way.
In the first patch Kamal introduces a new data type "mlx5e_stats_grp" This change
defines a new API to create a group of stats and simplifies the way of handling them.
This struct will define the following behavior per group:
- get_num_stats() - return the number of counters in the group.
- fill_strings() - fill counters strings within the group.
- fill_stats() - fill counters values within the group.
All other patches will be straight forward refactoring per stats group,
where Kamal will move each mlx5e stats group to use the new API.
The idea is to have better flexibility and modularity to add new counters,
all ethtool logic was rendered generic and loops through the generic stats groups and
calls the groups callbacks to figure out how and what to report back to user space.
Introducing new file en_stats.c to hold all the new stat groups logic and implementation.
Static structures (counters descriptors) moved from en_stats.h to en_stats.c which reduces
the mlx5_core binary footprint, originally reported and addressed by Stephen Hemminger:
("mlx5: fix space waste from ethtool descriptions") which was waived due to this re-design.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-10-31
This series contains updates to i40e, i40evf and net/sched.
Arnd Bergmann cleans up the power management code to resolve a build
warning.
Shannon Nelson fixes i40e to only redistribute our vectors when we did
not get the full count that we requested.
Alex reverts a previous commit because it potentially causes a memory leak
when combined with the current page recycling scheme.
Amritha enables configuring cloud filters in i40e using the tc-flower
classifier. The classification function of the filter is to match a
packet to a traffic class. cls_flower is extended to offload classid to
hardware. Hardware traffic classes are identified using classid values
reserved in the range :ffe0 - :ffef.
The cloud filters are added for a VSI and are cleaned up when the VSI is
deleted. The filters that match on L4 ports needs enhanced admin queue
functions with big buffer support for extended fields in cloud filter
commands.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
tdc.py reads a bunch of test cases in json files. When a json file
cannot be parsed, tdc just exits and does not run any tests.
This patch will cause tdc to print a message with the file name and
line number, then that file will be ignored and the rest of the tests
will be processed.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Acked-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check if tcase[k] is an instance of a list (is or is derived from list)
instead of checking if it is a list.
This will be useful if the data structures change to be something
that implements list, instead of being an actual list. In that
case, this code will not have to change.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Acked-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the config customization into a site-local file
tdc_config_local.py, so that updates of the tdc test
software does not require hand-editing of the config.
This patch includes a template for the site-local
customization file.
In addition, this makes it easy to revert to a stock
tdc environment for testing the test framework and/or
the core tests.
Also it makes it harder for any custom config to be
submitted back to the kernel tdc.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Acked-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ignore .pyc files, "python compiled" files, that get created
when a python script is run. They should never be committed.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Acked-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of documentation, supply some very simple test cases
to illustrate how test cases work. One test case shows
commands in the setup, command, verify and teardown stages.
Other test cases show how to have a working test case that
does not have commands in the setup, verify and/or teardown
stages.
Specifically, the command lists for setup and teardown can
be empty. And the verify command must have a command, but
it can be /bin/true. The regex must have a string, we
recommend a single space, and the count of matches must be
zero if you do not want to use the match feature of verify.
Verify will always look for a return code of success (0)
so we give /bin/true when we do not want to make a check
there.
Also, update the documentation for testcases to be more
specific in the cases of:
- accepting non-success return codes in setup and
teardown stages
- how to write the test when no setup, teardown
and/or verify are desired.
To run the example test cases:
$ sudo -E ./tdc.py -f creating-testcases/example.json -l
1f: (example) simple test to test framework
2f: (example) simple test, no need for verify
3f: (example) simple test, no need for setup or teardown (or verify)
$ sudo -E ./tdc.py -f creating-testcases/example.json
Test 1f: simple test to test framework
Test 2f: simple test, no need for verify
Test 3f: simple test, no need for setup or teardown (or verify)
All test results:
1..3
ok 1 1f simple test to test framework
ok 2 2f simple test, no need for verify
ok 3 3f simple test, no need for setup or teardown (or verify)
$
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Acked-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault says:
====================
l2tp: remove unused code
Patch #1 removes the ref/deref mechanism that was originally used to
prevent ppp pseudowires from dropping their sockets. This mechanism
was error prone and isn't used anymore.
Patch #2 removes some module specific refcount debugging.
Patches #3 and #4 take care of some dead code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With conversion to refcount_t, such manual debugging code doesn't make
sense anymore.
The tunnel part was already dropped by
54652eb12c ("l2tp: hold tunnel while looking up sessions in l2tp_netlink").
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ->ref() and ->deref() callbacks are unused since PPP stopped using
them in ee40fb2e1e ("l2tp: protect sock pointer of struct pppol2tp_session with RCU").
We can thus remove them from struct l2tp_session and drop the do_ref
parameter of l2tp_session_get*().
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the channels counters to use the new stats group API.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Reviewed-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Switch the ipsec counters to use the new stats group API.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Reviewed-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Switch the pme counters to use the new stats group API.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Reviewed-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
